--- zzzz-none-000/linux-3.10.107/arch/arm/mach-tegra/sleep-tegra20.S 2017-06-27 09:49:32.000000000 +0000 +++ scorpion-7490-727/linux-3.10.107/arch/arm/mach-tegra/sleep-tegra20.S 2021-02-04 17:41:59.000000000 +0000 @@ -23,10 +23,50 @@ #include #include #include +#include +#include "irammap.h" #include "sleep.h" #include "flowctrl.h" +#define EMC_CFG 0xc +#define EMC_ADR_CFG 0x10 +#define EMC_REFRESH 0x70 +#define EMC_NOP 0xdc +#define EMC_SELF_REF 0xe0 +#define EMC_REQ_CTRL 0x2b0 +#define EMC_EMC_STATUS 0x2b4 + +#define CLK_RESET_CCLK_BURST 0x20 +#define CLK_RESET_CCLK_DIVIDER 0x24 +#define CLK_RESET_SCLK_BURST 0x28 +#define CLK_RESET_SCLK_DIVIDER 0x2c +#define CLK_RESET_PLLC_BASE 0x80 +#define CLK_RESET_PLLM_BASE 0x90 +#define CLK_RESET_PLLP_BASE 0xa0 + +#define APB_MISC_XM2CFGCPADCTRL 0x8c8 +#define APB_MISC_XM2CFGDPADCTRL 0x8cc +#define APB_MISC_XM2CLKCFGPADCTRL 0x8d0 +#define APB_MISC_XM2COMPPADCTRL 0x8d4 +#define APB_MISC_XM2VTTGENPADCTRL 0x8d8 +#define APB_MISC_XM2CFGCPADCTRL2 0x8e4 +#define APB_MISC_XM2CFGDPADCTRL2 0x8e8 + +.macro pll_enable, rd, r_car_base, pll_base + ldr \rd, [\r_car_base, #\pll_base] + tst \rd, #(1 << 30) + orreq \rd, \rd, #(1 << 30) + streq \rd, [\r_car_base, #\pll_base] +.endm + +.macro emc_device_mask, rd, base + ldr \rd, [\base, #EMC_ADR_CFG] + tst \rd, #(0x3 << 24) + moveq \rd, #(0x1 << 8) @ just 1 device + movne \rd, #(0x3 << 8) @ 2 devices +.endm + #if defined(CONFIG_HOTPLUG_CPU) || defined(CONFIG_PM_SLEEP) /* * tegra20_hotplug_shutdown(void) @@ -38,7 +78,7 @@ /* Put this CPU down */ cpu_id r0 bl tegra20_cpu_shutdown - mov pc, lr @ should never get here + ret lr @ should never get here ENDPROC(tegra20_hotplug_shutdown) /* @@ -56,10 +96,11 @@ */ ENTRY(tegra20_cpu_shutdown) cmp r0, #0 - moveq pc, lr @ must not be called for CPU 0 - mov32 r1, TEGRA_PMC_VIRT + PMC_SCRATCH41 + reteq lr @ must not be called for CPU 0 + mov32 r1, TEGRA_IRAM_RESET_BASE_VIRT + ldr r2, =__tegra20_cpu1_resettable_status_offset mov r12, #CPU_RESETTABLE - str r12, [r1] + strb r12, [r1, r2] cpu_to_halt_reg r1, r0 ldr r3, =TEGRA_FLOW_CTRL_VIRT @@ -77,7 +118,7 @@ cpu_id r3 cmp r3, r0 beq . - mov pc, lr + ret lr ENDPROC(tegra20_cpu_shutdown) #endif @@ -124,7 +165,7 @@ cmpeq r12, r0 @ !turn == cpu? beq 1b @ while !turn == cpu && flag[!cpu] == 1 - mov pc, lr @ locked + ret lr @ locked ENDPROC(tegra_pen_lock) ENTRY(tegra_pen_unlock) @@ -136,51 +177,76 @@ addne r2, r3, #PMC_SCRATCH39 mov r12, #0 str r12, [r2] - mov pc, lr + ret lr ENDPROC(tegra_pen_unlock) /* * tegra20_cpu_clear_resettable(void) * - * Called to clear the "resettable soon" flag in PMC_SCRATCH41 when + * Called to clear the "resettable soon" flag in IRAM variable when * it is expected that the secondary CPU will be idle soon. */ ENTRY(tegra20_cpu_clear_resettable) - mov32 r1, TEGRA_PMC_VIRT + PMC_SCRATCH41 + mov32 r1, TEGRA_IRAM_RESET_BASE_VIRT + ldr r2, =__tegra20_cpu1_resettable_status_offset mov r12, #CPU_NOT_RESETTABLE - str r12, [r1] - mov pc, lr + strb r12, [r1, r2] + ret lr ENDPROC(tegra20_cpu_clear_resettable) /* * tegra20_cpu_set_resettable_soon(void) * - * Called to set the "resettable soon" flag in PMC_SCRATCH41 when + * Called to set the "resettable soon" flag in IRAM variable when * it is expected that the secondary CPU will be idle soon. */ ENTRY(tegra20_cpu_set_resettable_soon) - mov32 r1, TEGRA_PMC_VIRT + PMC_SCRATCH41 + mov32 r1, TEGRA_IRAM_RESET_BASE_VIRT + ldr r2, =__tegra20_cpu1_resettable_status_offset mov r12, #CPU_RESETTABLE_SOON - str r12, [r1] - mov pc, lr + strb r12, [r1, r2] + ret lr ENDPROC(tegra20_cpu_set_resettable_soon) /* * tegra20_cpu_is_resettable_soon(void) * - * Returns true if the "resettable soon" flag in PMC_SCRATCH41 has been + * Returns true if the "resettable soon" flag in IRAM variable has been * set because it is expected that the secondary CPU will be idle soon. */ ENTRY(tegra20_cpu_is_resettable_soon) - mov32 r1, TEGRA_PMC_VIRT + PMC_SCRATCH41 - ldr r12, [r1] + mov32 r1, TEGRA_IRAM_RESET_BASE_VIRT + ldr r2, =__tegra20_cpu1_resettable_status_offset + ldrb r12, [r1, r2] cmp r12, #CPU_RESETTABLE_SOON moveq r0, #1 movne r0, #0 - mov pc, lr + ret lr ENDPROC(tegra20_cpu_is_resettable_soon) /* + * tegra20_sleep_core_finish(unsigned long v2p) + * + * Enters suspend in LP0 or LP1 by turning off the mmu and jumping to + * tegra20_tear_down_core in IRAM + */ +ENTRY(tegra20_sleep_core_finish) + /* Flush, disable the L1 data cache and exit SMP */ + bl tegra_disable_clean_inv_dcache + + mov32 r3, tegra_shut_off_mmu + add r3, r3, r0 + + mov32 r0, tegra20_tear_down_core + mov32 r1, tegra20_iram_start + sub r0, r0, r1 + mov32 r1, TEGRA_IRAM_LPx_RESUME_AREA + add r0, r0, r1 + + ret r3 +ENDPROC(tegra20_sleep_core_finish) + +/* * tegra20_sleep_cpu_secondary_finish(unsigned long v2p) * * Enters WFI on secondary CPU by exiting coherency. @@ -191,11 +257,13 @@ mrc p15, 0, r11, c1, c0, 1 @ save actlr before exiting coherency /* Flush and disable the L1 data cache */ + mov r0, #TEGRA_FLUSH_CACHE_LOUIS bl tegra_disable_clean_inv_dcache - mov32 r0, TEGRA_PMC_VIRT + PMC_SCRATCH41 + mov32 r0, TEGRA_IRAM_RESET_BASE_VIRT + ldr r4, =__tegra20_cpu1_resettable_status_offset mov r3, #CPU_RESETTABLE - str r3, [r0] + strb r3, [r0, r4] bl tegra_cpu_do_idle @@ -211,10 +279,10 @@ bl tegra_pen_lock - mov32 r3, TEGRA_PMC_VIRT - add r0, r3, #PMC_SCRATCH41 + mov32 r0, TEGRA_IRAM_RESET_BASE_VIRT + ldr r4, =__tegra20_cpu1_resettable_status_offset mov r3, #CPU_NOT_RESETTABLE - str r3, [r0] + strb r3, [r0, r4] bl tegra_pen_unlock @@ -250,6 +318,150 @@ b tegra20_enter_sleep ENDPROC(tegra20_tear_down_cpu) +/* START OF ROUTINES COPIED TO IRAM */ + .align L1_CACHE_SHIFT + .globl tegra20_iram_start +tegra20_iram_start: + +/* + * tegra20_lp1_reset + * + * reset vector for LP1 restore; copied into IRAM during suspend. + * Brings the system back up to a safe staring point (SDRAM out of + * self-refresh, PLLC, PLLM and PLLP reenabled, CPU running on PLLP, + * system clock running on the same PLL that it suspended at), and + * jumps to tegra_resume to restore virtual addressing and PLLX. + * The physical address of tegra_resume expected to be stored in + * PMC_SCRATCH41. + * + * NOTE: THIS *MUST* BE RELOCATED TO TEGRA_IRAM_LPx_RESUME_AREA. + */ +ENTRY(tegra20_lp1_reset) + /* + * The CPU and system bus are running at 32KHz and executing from + * IRAM when this code is executed; immediately switch to CLKM and + * enable PLLM, PLLP, PLLC. + */ + mov32 r0, TEGRA_CLK_RESET_BASE + + mov r1, #(1 << 28) + str r1, [r0, #CLK_RESET_SCLK_BURST] + str r1, [r0, #CLK_RESET_CCLK_BURST] + mov r1, #0 + str r1, [r0, #CLK_RESET_CCLK_DIVIDER] + str r1, [r0, #CLK_RESET_SCLK_DIVIDER] + + pll_enable r1, r0, CLK_RESET_PLLM_BASE + pll_enable r1, r0, CLK_RESET_PLLP_BASE + pll_enable r1, r0, CLK_RESET_PLLC_BASE + + adr r2, tegra20_sdram_pad_address + adr r4, tegra20_sdram_pad_save + mov r5, #0 + + ldr r6, tegra20_sdram_pad_size +padload: + ldr r7, [r2, r5] @ r7 is the addr in the pad_address + + ldr r1, [r4, r5] + str r1, [r7] @ restore the value in pad_save + + add r5, r5, #4 + cmp r6, r5 + bne padload + +padload_done: + /* 255uS delay for PLL stabilization */ + mov32 r7, TEGRA_TMRUS_BASE + ldr r1, [r7] + add r1, r1, #0xff + wait_until r1, r7, r9 + + adr r4, tegra20_sclk_save + ldr r4, [r4] + str r4, [r0, #CLK_RESET_SCLK_BURST] + mov32 r4, ((1 << 28) | (4)) @ burst policy is PLLP + str r4, [r0, #CLK_RESET_CCLK_BURST] + + mov32 r0, TEGRA_EMC_BASE + ldr r1, [r0, #EMC_CFG] + bic r1, r1, #(1 << 31) @ disable DRAM_CLK_STOP + str r1, [r0, #EMC_CFG] + + mov r1, #0 + str r1, [r0, #EMC_SELF_REF] @ take DRAM out of self refresh + mov r1, #1 + str r1, [r0, #EMC_NOP] + str r1, [r0, #EMC_NOP] + str r1, [r0, #EMC_REFRESH] + + emc_device_mask r1, r0 + +exit_selfrefresh_loop: + ldr r2, [r0, #EMC_EMC_STATUS] + ands r2, r2, r1 + bne exit_selfrefresh_loop + + mov r1, #0 @ unstall all transactions + str r1, [r0, #EMC_REQ_CTRL] + + mov32 r0, TEGRA_PMC_BASE + ldr r0, [r0, #PMC_SCRATCH41] + ret r0 @ jump to tegra_resume +ENDPROC(tegra20_lp1_reset) + +/* + * tegra20_tear_down_core + * + * copied into and executed from IRAM + * puts memory in self-refresh for LP0 and LP1 + */ +tegra20_tear_down_core: + bl tegra20_sdram_self_refresh + bl tegra20_switch_cpu_to_clk32k + b tegra20_enter_sleep + +/* + * tegra20_switch_cpu_to_clk32k + * + * In LP0 and LP1 all PLLs will be turned off. Switch the CPU and system clock + * to the 32KHz clock. + */ +tegra20_switch_cpu_to_clk32k: + /* + * start by switching to CLKM to safely disable PLLs, then switch to + * CLKS. + */ + mov r0, #(1 << 28) + str r0, [r5, #CLK_RESET_SCLK_BURST] + str r0, [r5, #CLK_RESET_CCLK_BURST] + mov r0, #0 + str r0, [r5, #CLK_RESET_CCLK_DIVIDER] + str r0, [r5, #CLK_RESET_SCLK_DIVIDER] + + /* 2uS delay delay between changing SCLK and disabling PLLs */ + mov32 r7, TEGRA_TMRUS_BASE + ldr r1, [r7] + add r1, r1, #2 + wait_until r1, r7, r9 + + /* disable PLLM, PLLP and PLLC */ + ldr r0, [r5, #CLK_RESET_PLLM_BASE] + bic r0, r0, #(1 << 30) + str r0, [r5, #CLK_RESET_PLLM_BASE] + ldr r0, [r5, #CLK_RESET_PLLP_BASE] + bic r0, r0, #(1 << 30) + str r0, [r5, #CLK_RESET_PLLP_BASE] + ldr r0, [r5, #CLK_RESET_PLLC_BASE] + bic r0, r0, #(1 << 30) + str r0, [r5, #CLK_RESET_PLLC_BASE] + + /* switch to CLKS */ + mov r0, #0 /* brust policy = 32KHz */ + str r0, [r5, #CLK_RESET_SCLK_BURST] + + ret lr + /* * tegra20_enter_sleep * @@ -274,4 +486,95 @@ isb b halted +/* + * tegra20_sdram_self_refresh + * + * called with MMU off and caches disabled + * puts sdram in self refresh + * must be executed from IRAM + */ +tegra20_sdram_self_refresh: + mov32 r1, TEGRA_EMC_BASE @ r1 reserved for emc base addr + + mov r2, #3 + str r2, [r1, #EMC_REQ_CTRL] @ stall incoming DRAM requests + +emcidle: + ldr r2, [r1, #EMC_EMC_STATUS] + tst r2, #4 + beq emcidle + + mov r2, #1 + str r2, [r1, #EMC_SELF_REF] + + emc_device_mask r2, r1 + +emcself: + ldr r3, [r1, #EMC_EMC_STATUS] + and r3, r3, r2 + cmp r3, r2 + bne emcself @ loop until DDR in self-refresh + + adr r2, tegra20_sdram_pad_address + adr r3, tegra20_sdram_pad_safe + adr r4, tegra20_sdram_pad_save + mov r5, #0 + + ldr r6, tegra20_sdram_pad_size +padsave: + ldr r0, [r2, r5] @ r0 is the addr in the pad_address + + ldr r1, [r0] + str r1, [r4, r5] @ save the content of the addr + + ldr r1, [r3, r5] + str r1, [r0] @ set the save val to the addr + + add r5, r5, #4 + cmp r6, r5 + bne padsave +padsave_done: + + mov32 r5, TEGRA_CLK_RESET_BASE + ldr r0, [r5, #CLK_RESET_SCLK_BURST] + adr r2, tegra20_sclk_save + str r0, [r2] + dsb + ret lr + +tegra20_sdram_pad_address: + .word TEGRA_APB_MISC_BASE + APB_MISC_XM2CFGCPADCTRL + .word TEGRA_APB_MISC_BASE + APB_MISC_XM2CFGDPADCTRL + .word TEGRA_APB_MISC_BASE + APB_MISC_XM2CLKCFGPADCTRL + .word TEGRA_APB_MISC_BASE + APB_MISC_XM2COMPPADCTRL + .word TEGRA_APB_MISC_BASE + APB_MISC_XM2VTTGENPADCTRL + .word TEGRA_APB_MISC_BASE + APB_MISC_XM2CFGCPADCTRL2 + .word TEGRA_APB_MISC_BASE + APB_MISC_XM2CFGDPADCTRL2 + +tegra20_sdram_pad_size: + .word tegra20_sdram_pad_size - tegra20_sdram_pad_address + +tegra20_sdram_pad_safe: + .word 0x8 + .word 0x8 + .word 0x0 + .word 0x8 + .word 0x5500 + .word 0x08080040 + .word 0x0 + +tegra20_sclk_save: + .word 0x0 + +tegra20_sdram_pad_save: + .rept (tegra20_sdram_pad_size - tegra20_sdram_pad_address) / 4 + .long 0 + .endr + + .ltorg +/* dummy symbol for end of IRAM */ + .align L1_CACHE_SHIFT + .globl tegra20_iram_end +tegra20_iram_end: + b . #endif