--- zzzz-none-000/linux-3.10.107/arch/arm/mach-tegra/sleep-tegra30.S 2017-06-27 09:49:32.000000000 +0000 +++ scorpion-7490-727/linux-3.10.107/arch/arm/mach-tegra/sleep-tegra30.S 2021-02-04 17:41:59.000000000 +0000 @@ -16,14 +16,122 @@ #include -#include +#include + #include +#include +#include -#include "sleep.h" #include "flowctrl.h" +#include "irammap.h" +#include "sleep.h" + +#define EMC_CFG 0xc +#define EMC_ADR_CFG 0x10 +#define EMC_TIMING_CONTROL 0x28 +#define EMC_REFRESH 0x70 +#define EMC_NOP 0xdc +#define EMC_SELF_REF 0xe0 +#define EMC_MRW 0xe8 +#define EMC_FBIO_CFG5 0x104 +#define EMC_AUTO_CAL_CONFIG 0x2a4 +#define EMC_AUTO_CAL_INTERVAL 0x2a8 +#define EMC_AUTO_CAL_STATUS 0x2ac +#define EMC_REQ_CTRL 0x2b0 +#define EMC_CFG_DIG_DLL 0x2bc +#define EMC_EMC_STATUS 0x2b4 +#define EMC_ZCAL_INTERVAL 0x2e0 +#define EMC_ZQ_CAL 0x2ec +#define EMC_XM2VTTGENPADCTRL 0x310 +#define EMC_XM2VTTGENPADCTRL2 0x314 + +#define PMC_CTRL 0x0 +#define PMC_CTRL_SIDE_EFFECT_LP0 (1 << 14) /* enter LP0 when CPU pwr gated */ + +#define PMC_PLLP_WB0_OVERRIDE 0xf8 +#define PMC_IO_DPD_REQ 0x1b8 +#define PMC_IO_DPD_STATUS 0x1bc + +#define CLK_RESET_CCLK_BURST 0x20 +#define CLK_RESET_CCLK_DIVIDER 0x24 +#define CLK_RESET_SCLK_BURST 0x28 +#define CLK_RESET_SCLK_DIVIDER 0x2c + +#define CLK_RESET_PLLC_BASE 0x80 +#define CLK_RESET_PLLC_MISC 0x8c +#define CLK_RESET_PLLM_BASE 0x90 +#define CLK_RESET_PLLM_MISC 0x9c +#define CLK_RESET_PLLP_BASE 0xa0 +#define CLK_RESET_PLLP_MISC 0xac +#define CLK_RESET_PLLA_BASE 0xb0 +#define CLK_RESET_PLLA_MISC 0xbc +#define CLK_RESET_PLLX_BASE 0xe0 +#define CLK_RESET_PLLX_MISC 0xe4 +#define CLK_RESET_PLLX_MISC3 0x518 +#define CLK_RESET_PLLX_MISC3_IDDQ 3 +#define CLK_RESET_PLLM_MISC_IDDQ 5 +#define CLK_RESET_PLLC_MISC_IDDQ 26 + +#define CLK_RESET_CLK_SOURCE_MSELECT 0x3b4 + +#define MSELECT_CLKM (0x3 << 30) + +#define LOCK_DELAY 50 /* safety delay after lock is detected */ #define TEGRA30_POWER_HOTPLUG_SHUTDOWN (1 << 27) /* Hotplug shutdown */ +.macro emc_device_mask, rd, base + ldr \rd, [\base, #EMC_ADR_CFG] + tst \rd, #0x1 + moveq \rd, #(0x1 << 8) @ just 1 device + movne \rd, #(0x3 << 8) @ 2 devices +.endm + +.macro emc_timing_update, rd, base + mov \rd, #1 + str \rd, [\base, #EMC_TIMING_CONTROL] +1001: + ldr \rd, [\base, #EMC_EMC_STATUS] + tst \rd, #(0x1<<23) @ wait EMC_STATUS_TIMING_UPDATE_STALLED is clear + bne 1001b +.endm + +.macro pll_enable, rd, r_car_base, pll_base, pll_misc + ldr \rd, [\r_car_base, #\pll_base] + tst \rd, #(1 << 30) + orreq \rd, \rd, #(1 << 30) + streq \rd, [\r_car_base, #\pll_base] + /* Enable lock detector */ + .if \pll_misc + ldr \rd, [\r_car_base, #\pll_misc] + bic \rd, \rd, #(1 << 18) + str \rd, [\r_car_base, #\pll_misc] + ldr \rd, [\r_car_base, #\pll_misc] + ldr \rd, [\r_car_base, #\pll_misc] + orr \rd, \rd, #(1 << 18) + str \rd, [\r_car_base, #\pll_misc] + .endif +.endm + +.macro pll_locked, rd, r_car_base, pll_base +1: + ldr \rd, [\r_car_base, #\pll_base] + tst \rd, #(1 << 27) + beq 1b +.endm + +.macro pll_iddq_exit, rd, car, iddq, iddq_bit + ldr \rd, [\car, #\iddq] + bic \rd, \rd, #(1<<\iddq_bit) + str \rd, [\car, #\iddq] +.endm + +.macro pll_iddq_entry, rd, car, iddq, iddq_bit + ldr \rd, [\car, #\iddq] + orr \rd, \rd, #(1<<\iddq_bit) + str \rd, [\car, #\iddq] +.endm + #if defined(CONFIG_HOTPLUG_CPU) || defined(CONFIG_PM_SLEEP) /* * tegra30_hotplug_shutdown(void) @@ -35,7 +143,7 @@ /* Powergate this CPU */ mov r0, #TEGRA30_POWER_HOTPLUG_SHUTDOWN bl tegra30_cpu_shutdown - mov pc, lr @ should never get here + ret lr @ should never get here ENDPROC(tegra30_hotplug_shutdown) /* @@ -43,14 +151,19 @@ * * Puts the current CPU in wait-for-event mode on the flow controller * and powergates it -- flags (in R0) indicate the request type. - * Must never be called for CPU 0. * - * corrupts r0-r4, r12 + * r10 = SoC ID + * corrupts r0-r4, r10-r12 */ ENTRY(tegra30_cpu_shutdown) cpu_id r3 + tegra_get_soc_id TEGRA_APB_MISC_VIRT, r10 + cmp r10, #TEGRA30 + bne _no_cpu0_chk @ It's not Tegra30 + cmp r3, #0 - moveq pc, lr @ Must never be called for CPU 0 + reteq lr @ Must never be called for CPU 0 +_no_cpu0_chk: ldr r12, =TEGRA_FLOW_CTRL_VIRT cpu_to_csr_reg r1, r3 @@ -65,7 +178,9 @@ movw r12, \ FLOW_CTRL_CSR_INTR_FLAG | FLOW_CTRL_CSR_EVENT_FLAG | \ FLOW_CTRL_CSR_ENABLE - mov r4, #(1 << 4) + cmp r10, #TEGRA30 + moveq r4, #(1 << 4) @ wfe bitmap + movne r4, #(1 << 8) @ wfi bitmap ARM( orr r12, r12, r4, lsl r3 ) THUMB( lsl r4, r4, r3 ) THUMB( orr r12, r12, r4 ) @@ -79,9 +194,22 @@ cpsid a @ disable imprecise aborts. ldr r3, [r1] @ read CSR str r3, [r1] @ clear CSR + tst r0, #TEGRA30_POWER_HOTPLUG_SHUTDOWN + beq flow_ctrl_setting_for_lp2 + + /* flow controller set up for hotplug */ + mov r3, #FLOW_CTRL_WAITEVENT @ For hotplug + b flow_ctrl_done +flow_ctrl_setting_for_lp2: + /* flow controller set up for LP2 */ + cmp r10, #TEGRA30 moveq r3, #FLOW_CTRL_WAIT_FOR_INTERRUPT @ For LP2 - movne r3, #FLOW_CTRL_WAITEVENT @ For hotplug + movne r3, #FLOW_CTRL_WAITEVENT + orrne r3, r3, #FLOW_CTRL_HALT_GIC_IRQ + orrne r3, r3, #FLOW_CTRL_HALT_GIC_FIQ +flow_ctrl_done: + cmp r10, #TEGRA30 str r3, [r2] ldr r0, [r2] b wfe_war @@ -89,12 +217,13 @@ __cpu_reset_again: dsb .align 5 - wfe @ CPU should be power gated here + wfeeq @ CPU should be power gated here + wfine wfe_war: b __cpu_reset_again /* - * 38 nop's, which fills reset of wfe cache line and + * 38 nop's, which fills rest of wfe cache line and * 4 more cachelines with nop */ .rept 38 @@ -107,6 +236,41 @@ #ifdef CONFIG_PM_SLEEP /* + * tegra30_sleep_core_finish(unsigned long v2p) + * + * Enters suspend in LP0 or LP1 by turning off the MMU and jumping to + * tegra30_tear_down_core in IRAM + */ +ENTRY(tegra30_sleep_core_finish) + /* Flush, disable the L1 data cache and exit SMP */ + bl tegra_disable_clean_inv_dcache + + /* + * Preload all the address literals that are needed for the + * CPU power-gating process, to avoid loading from SDRAM which + * are not supported once SDRAM is put into self-refresh. + * LP0 / LP1 use physical address, since the MMU needs to be + * disabled before putting SDRAM into self-refresh to avoid + * memory access due to page table walks. + */ + mov32 r4, TEGRA_PMC_BASE + mov32 r5, TEGRA_CLK_RESET_BASE + mov32 r6, TEGRA_FLOW_CTRL_BASE + mov32 r7, TEGRA_TMRUS_BASE + + mov32 r3, tegra_shut_off_mmu + add r3, r3, r0 + + mov32 r0, tegra30_tear_down_core + mov32 r1, tegra30_iram_start + sub r0, r0, r1 + mov32 r1, TEGRA_IRAM_LPx_RESUME_AREA + add r0, r0, r1 + + ret r3 +ENDPROC(tegra30_sleep_core_finish) + +/* * tegra30_sleep_cpu_secondary_finish(unsigned long v2p) * * Enters LP2 on secondary CPU by exiting coherency and powergating the CPU. @@ -115,13 +279,14 @@ mov r7, lr /* Flush and disable the L1 data cache */ + mov r0, #TEGRA_FLUSH_CACHE_LOUIS bl tegra_disable_clean_inv_dcache /* Powergate this CPU. */ mov r0, #0 @ power mode flags (!hotplug) bl tegra30_cpu_shutdown mov r0, #1 @ never return here - mov pc, r7 + ret r7 ENDPROC(tegra30_sleep_cpu_secondary_finish) /* @@ -135,6 +300,368 @@ b tegra30_enter_sleep ENDPROC(tegra30_tear_down_cpu) +/* START OF ROUTINES COPIED TO IRAM */ + .align L1_CACHE_SHIFT + .globl tegra30_iram_start +tegra30_iram_start: + +/* + * tegra30_lp1_reset + * + * reset vector for LP1 restore; copied into IRAM during suspend. + * Brings the system back up to a safe staring point (SDRAM out of + * self-refresh, PLLC, PLLM and PLLP reenabled, CPU running on PLLX, + * system clock running on the same PLL that it suspended at), and + * jumps to tegra_resume to restore virtual addressing. + * The physical address of tegra_resume expected to be stored in + * PMC_SCRATCH41. + * + * NOTE: THIS *MUST* BE RELOCATED TO TEGRA_IRAM_LPx_RESUME_AREA. + */ +ENTRY(tegra30_lp1_reset) + /* + * The CPU and system bus are running at 32KHz and executing from + * IRAM when this code is executed; immediately switch to CLKM and + * enable PLLP, PLLM, PLLC, PLLA and PLLX. + */ + mov32 r0, TEGRA_CLK_RESET_BASE + + mov r1, #(1 << 28) + str r1, [r0, #CLK_RESET_SCLK_BURST] + str r1, [r0, #CLK_RESET_CCLK_BURST] + mov r1, #0 + str r1, [r0, #CLK_RESET_CCLK_DIVIDER] + str r1, [r0, #CLK_RESET_SCLK_DIVIDER] + + tegra_get_soc_id TEGRA_APB_MISC_BASE, r10 + cmp r10, #TEGRA30 + beq _no_pll_iddq_exit + + pll_iddq_exit r1, r0, CLK_RESET_PLLM_MISC, CLK_RESET_PLLM_MISC_IDDQ + pll_iddq_exit r1, r0, CLK_RESET_PLLC_MISC, CLK_RESET_PLLC_MISC_IDDQ + pll_iddq_exit r1, r0, CLK_RESET_PLLX_MISC3, CLK_RESET_PLLX_MISC3_IDDQ + + mov32 r7, TEGRA_TMRUS_BASE + ldr r1, [r7] + add r1, r1, #2 + wait_until r1, r7, r3 + + /* enable PLLM via PMC */ + mov32 r2, TEGRA_PMC_BASE + ldr r1, [r2, #PMC_PLLP_WB0_OVERRIDE] + orr r1, r1, #(1 << 12) + str r1, [r2, #PMC_PLLP_WB0_OVERRIDE] + + pll_enable r1, r0, CLK_RESET_PLLM_BASE, 0 + pll_enable r1, r0, CLK_RESET_PLLC_BASE, 0 + pll_enable r1, r0, CLK_RESET_PLLX_BASE, 0 + + b _pll_m_c_x_done + +_no_pll_iddq_exit: + /* enable PLLM via PMC */ + mov32 r2, TEGRA_PMC_BASE + ldr r1, [r2, #PMC_PLLP_WB0_OVERRIDE] + orr r1, r1, #(1 << 12) + str r1, [r2, #PMC_PLLP_WB0_OVERRIDE] + + pll_enable r1, r0, CLK_RESET_PLLM_BASE, CLK_RESET_PLLM_MISC + pll_enable r1, r0, CLK_RESET_PLLC_BASE, CLK_RESET_PLLC_MISC + pll_enable r1, r0, CLK_RESET_PLLX_BASE, CLK_RESET_PLLX_MISC + +_pll_m_c_x_done: + pll_enable r1, r0, CLK_RESET_PLLP_BASE, CLK_RESET_PLLP_MISC + pll_enable r1, r0, CLK_RESET_PLLA_BASE, CLK_RESET_PLLA_MISC + + pll_locked r1, r0, CLK_RESET_PLLM_BASE + pll_locked r1, r0, CLK_RESET_PLLP_BASE + pll_locked r1, r0, CLK_RESET_PLLA_BASE + pll_locked r1, r0, CLK_RESET_PLLC_BASE + pll_locked r1, r0, CLK_RESET_PLLX_BASE + + mov32 r7, TEGRA_TMRUS_BASE + ldr r1, [r7] + add r1, r1, #LOCK_DELAY + wait_until r1, r7, r3 + + adr r5, tegra_sdram_pad_save + + ldr r4, [r5, #0x18] @ restore CLK_SOURCE_MSELECT + str r4, [r0, #CLK_RESET_CLK_SOURCE_MSELECT] + + ldr r4, [r5, #0x1C] @ restore SCLK_BURST + str r4, [r0, #CLK_RESET_SCLK_BURST] + + cmp r10, #TEGRA30 + movweq r4, #:lower16:((1 << 28) | (0x8)) @ burst policy is PLLX + movteq r4, #:upper16:((1 << 28) | (0x8)) + movwne r4, #:lower16:((1 << 28) | (0xe)) + movtne r4, #:upper16:((1 << 28) | (0xe)) + str r4, [r0, #CLK_RESET_CCLK_BURST] + + /* Restore pad power state to normal */ + ldr r1, [r5, #0x14] @ PMC_IO_DPD_STATUS + mvn r1, r1 + bic r1, r1, #(1 << 31) + orr r1, r1, #(1 << 30) + str r1, [r2, #PMC_IO_DPD_REQ] @ DPD_OFF + + cmp r10, #TEGRA30 + movweq r0, #:lower16:TEGRA_EMC_BASE @ r0 reserved for emc base + movteq r0, #:upper16:TEGRA_EMC_BASE + cmp r10, #TEGRA114 + movweq r0, #:lower16:TEGRA_EMC0_BASE + movteq r0, #:upper16:TEGRA_EMC0_BASE + cmp r10, #TEGRA124 + movweq r0, #:lower16:TEGRA124_EMC_BASE + movteq r0, #:upper16:TEGRA124_EMC_BASE + +exit_self_refresh: + ldr r1, [r5, #0xC] @ restore EMC_XM2VTTGENPADCTRL + str r1, [r0, #EMC_XM2VTTGENPADCTRL] + ldr r1, [r5, #0x10] @ restore EMC_XM2VTTGENPADCTRL2 + str r1, [r0, #EMC_XM2VTTGENPADCTRL2] + ldr r1, [r5, #0x8] @ restore EMC_AUTO_CAL_INTERVAL + str r1, [r0, #EMC_AUTO_CAL_INTERVAL] + + /* Relock DLL */ + ldr r1, [r0, #EMC_CFG_DIG_DLL] + orr r1, r1, #(1 << 30) @ set DLL_RESET + str r1, [r0, #EMC_CFG_DIG_DLL] + + emc_timing_update r1, r0 + + cmp r10, #TEGRA114 + movweq r1, #:lower16:TEGRA_EMC1_BASE + movteq r1, #:upper16:TEGRA_EMC1_BASE + cmpeq r0, r1 + + ldr r1, [r0, #EMC_AUTO_CAL_CONFIG] + orr r1, r1, #(1 << 31) @ set AUTO_CAL_ACTIVE + orreq r1, r1, #(1 << 27) @ set slave mode for channel 1 + str r1, [r0, #EMC_AUTO_CAL_CONFIG] + +emc_wait_auto_cal_onetime: + ldr r1, [r0, #EMC_AUTO_CAL_STATUS] + tst r1, #(1 << 31) @ wait until AUTO_CAL_ACTIVE is cleared + bne emc_wait_auto_cal_onetime + + ldr r1, [r0, #EMC_CFG] + bic r1, r1, #(1 << 31) @ disable DRAM_CLK_STOP_PD + str r1, [r0, #EMC_CFG] + + mov r1, #0 + str r1, [r0, #EMC_SELF_REF] @ take DRAM out of self refresh + mov r1, #1 + cmp r10, #TEGRA30 + streq r1, [r0, #EMC_NOP] + streq r1, [r0, #EMC_NOP] + streq r1, [r0, #EMC_REFRESH] + + emc_device_mask r1, r0 + +exit_selfrefresh_loop: + ldr r2, [r0, #EMC_EMC_STATUS] + ands r2, r2, r1 + bne exit_selfrefresh_loop + + lsr r1, r1, #8 @ devSel, bit0:dev0, bit1:dev1 + + mov32 r7, TEGRA_TMRUS_BASE + ldr r2, [r0, #EMC_FBIO_CFG5] + + and r2, r2, #3 @ check DRAM_TYPE + cmp r2, #2 + beq emc_lpddr2 + + /* Issue a ZQ_CAL for dev0 - DDR3 */ + mov32 r2, 0x80000011 @ DEV_SELECTION=2, LENGTH=LONG, CMD=1 + str r2, [r0, #EMC_ZQ_CAL] + ldr r2, [r7] + add r2, r2, #10 + wait_until r2, r7, r3 + + tst r1, #2 + beq zcal_done + + /* Issue a ZQ_CAL for dev1 - DDR3 */ + mov32 r2, 0x40000011 @ DEV_SELECTION=1, LENGTH=LONG, CMD=1 + str r2, [r0, #EMC_ZQ_CAL] + ldr r2, [r7] + add r2, r2, #10 + wait_until r2, r7, r3 + b zcal_done + +emc_lpddr2: + /* Issue a ZQ_CAL for dev0 - LPDDR2 */ + mov32 r2, 0x800A00AB @ DEV_SELECTION=2, MA=10, OP=0xAB + str r2, [r0, #EMC_MRW] + ldr r2, [r7] + add r2, r2, #1 + wait_until r2, r7, r3 + + tst r1, #2 + beq zcal_done + + /* Issue a ZQ_CAL for dev0 - LPDDR2 */ + mov32 r2, 0x400A00AB @ DEV_SELECTION=1, MA=10, OP=0xAB + str r2, [r0, #EMC_MRW] + ldr r2, [r7] + add r2, r2, #1 + wait_until r2, r7, r3 + +zcal_done: + mov r1, #0 @ unstall all transactions + str r1, [r0, #EMC_REQ_CTRL] + ldr r1, [r5, #0x4] @ restore EMC_ZCAL_INTERVAL + str r1, [r0, #EMC_ZCAL_INTERVAL] + ldr r1, [r5, #0x0] @ restore EMC_CFG + str r1, [r0, #EMC_CFG] + + /* Tegra114 had dual EMC channel, now config the other one */ + cmp r10, #TEGRA114 + bne __no_dual_emc_chanl + mov32 r1, TEGRA_EMC1_BASE + cmp r0, r1 + movne r0, r1 + addne r5, r5, #0x20 + bne exit_self_refresh +__no_dual_emc_chanl: + + mov32 r0, TEGRA_PMC_BASE + ldr r0, [r0, #PMC_SCRATCH41] + ret r0 @ jump to tegra_resume +ENDPROC(tegra30_lp1_reset) + + .align L1_CACHE_SHIFT +tegra30_sdram_pad_address: + .word TEGRA_EMC_BASE + EMC_CFG @0x0 + .word TEGRA_EMC_BASE + EMC_ZCAL_INTERVAL @0x4 + .word TEGRA_EMC_BASE + EMC_AUTO_CAL_INTERVAL @0x8 + .word TEGRA_EMC_BASE + EMC_XM2VTTGENPADCTRL @0xc + .word TEGRA_EMC_BASE + EMC_XM2VTTGENPADCTRL2 @0x10 + .word TEGRA_PMC_BASE + PMC_IO_DPD_STATUS @0x14 + .word TEGRA_CLK_RESET_BASE + CLK_RESET_CLK_SOURCE_MSELECT @0x18 + .word TEGRA_CLK_RESET_BASE + CLK_RESET_SCLK_BURST @0x1c +tegra30_sdram_pad_address_end: + +tegra114_sdram_pad_address: + .word TEGRA_EMC0_BASE + EMC_CFG @0x0 + .word TEGRA_EMC0_BASE + EMC_ZCAL_INTERVAL @0x4 + .word TEGRA_EMC0_BASE + EMC_AUTO_CAL_INTERVAL @0x8 + .word TEGRA_EMC0_BASE + EMC_XM2VTTGENPADCTRL @0xc + .word TEGRA_EMC0_BASE + EMC_XM2VTTGENPADCTRL2 @0x10 + .word TEGRA_PMC_BASE + PMC_IO_DPD_STATUS @0x14 + .word TEGRA_CLK_RESET_BASE + CLK_RESET_CLK_SOURCE_MSELECT @0x18 + .word TEGRA_CLK_RESET_BASE + CLK_RESET_SCLK_BURST @0x1c + .word TEGRA_EMC1_BASE + EMC_CFG @0x20 + .word TEGRA_EMC1_BASE + EMC_ZCAL_INTERVAL @0x24 + .word TEGRA_EMC1_BASE + EMC_AUTO_CAL_INTERVAL @0x28 + .word TEGRA_EMC1_BASE + EMC_XM2VTTGENPADCTRL @0x2c + .word TEGRA_EMC1_BASE + EMC_XM2VTTGENPADCTRL2 @0x30 +tegra114_sdram_pad_adress_end: + +tegra124_sdram_pad_address: + .word TEGRA124_EMC_BASE + EMC_CFG @0x0 + .word TEGRA124_EMC_BASE + EMC_ZCAL_INTERVAL @0x4 + .word TEGRA124_EMC_BASE + EMC_AUTO_CAL_INTERVAL @0x8 + .word TEGRA124_EMC_BASE + EMC_XM2VTTGENPADCTRL @0xc + .word TEGRA124_EMC_BASE + EMC_XM2VTTGENPADCTRL2 @0x10 + .word TEGRA_PMC_BASE + PMC_IO_DPD_STATUS @0x14 + .word TEGRA_CLK_RESET_BASE + CLK_RESET_CLK_SOURCE_MSELECT @0x18 + .word TEGRA_CLK_RESET_BASE + CLK_RESET_SCLK_BURST @0x1c +tegra124_sdram_pad_address_end: + +tegra30_sdram_pad_size: + .word tegra30_sdram_pad_address_end - tegra30_sdram_pad_address + +tegra114_sdram_pad_size: + .word tegra114_sdram_pad_adress_end - tegra114_sdram_pad_address + + .type tegra_sdram_pad_save, %object +tegra_sdram_pad_save: + .rept (tegra114_sdram_pad_adress_end - tegra114_sdram_pad_address) / 4 + .long 0 + .endr + +/* + * tegra30_tear_down_core + * + * copied into and executed from IRAM + * puts memory in self-refresh for LP0 and LP1 + */ +tegra30_tear_down_core: + bl tegra30_sdram_self_refresh + bl tegra30_switch_cpu_to_clk32k + b tegra30_enter_sleep + +/* + * tegra30_switch_cpu_to_clk32k + * + * In LP0 and LP1 all PLLs will be turned off. Switching the CPU and System CLK + * to the 32KHz clock. + * r4 = TEGRA_PMC_BASE + * r5 = TEGRA_CLK_RESET_BASE + * r6 = TEGRA_FLOW_CTRL_BASE + * r7 = TEGRA_TMRUS_BASE + * r10= SoC ID + */ +tegra30_switch_cpu_to_clk32k: + /* + * start by jumping to CLKM to safely disable PLLs, then jump to + * CLKS. + */ + mov r0, #(1 << 28) + str r0, [r5, #CLK_RESET_SCLK_BURST] + /* 2uS delay delay between changing SCLK and CCLK */ + ldr r1, [r7] + add r1, r1, #2 + wait_until r1, r7, r9 + str r0, [r5, #CLK_RESET_CCLK_BURST] + mov r0, #0 + str r0, [r5, #CLK_RESET_CCLK_DIVIDER] + str r0, [r5, #CLK_RESET_SCLK_DIVIDER] + + /* switch the clock source of mselect to be CLK_M */ + ldr r0, [r5, #CLK_RESET_CLK_SOURCE_MSELECT] + orr r0, r0, #MSELECT_CLKM + str r0, [r5, #CLK_RESET_CLK_SOURCE_MSELECT] + + /* 2uS delay delay between changing SCLK and disabling PLLs */ + ldr r1, [r7] + add r1, r1, #2 + wait_until r1, r7, r9 + + /* disable PLLM via PMC in LP1 */ + ldr r0, [r4, #PMC_PLLP_WB0_OVERRIDE] + bic r0, r0, #(1 << 12) + str r0, [r4, #PMC_PLLP_WB0_OVERRIDE] + + /* disable PLLP, PLLA, PLLC and PLLX */ + ldr r0, [r5, #CLK_RESET_PLLP_BASE] + bic r0, r0, #(1 << 30) + str r0, [r5, #CLK_RESET_PLLP_BASE] + ldr r0, [r5, #CLK_RESET_PLLA_BASE] + bic r0, r0, #(1 << 30) + str r0, [r5, #CLK_RESET_PLLA_BASE] + ldr r0, [r5, #CLK_RESET_PLLC_BASE] + bic r0, r0, #(1 << 30) + str r0, [r5, #CLK_RESET_PLLC_BASE] + ldr r0, [r5, #CLK_RESET_PLLX_BASE] + bic r0, r0, #(1 << 30) + str r0, [r5, #CLK_RESET_PLLX_BASE] + + cmp r10, #TEGRA30 + beq _no_pll_in_iddq + pll_iddq_entry r1, r5, CLK_RESET_PLLX_MISC3, CLK_RESET_PLLX_MISC3_IDDQ +_no_pll_in_iddq: + + /* switch to CLKS */ + mov r0, #0 /* brust policy = 32KHz */ + str r0, [r5, #CLK_RESET_SCLK_BURST] + + ret lr + /* * tegra30_enter_sleep * @@ -152,8 +679,12 @@ orr r0, r0, #FLOW_CTRL_CSR_ENABLE str r0, [r6, r2] + tegra_get_soc_id TEGRA_APB_MISC_BASE, r10 + cmp r10, #TEGRA30 mov r0, #FLOW_CTRL_WAIT_FOR_INTERRUPT - orr r0, r0, #FLOW_CTRL_HALT_CPU_IRQ | FLOW_CTRL_HALT_CPU_FIQ + orreq r0, r0, #FLOW_CTRL_HALT_CPU_IRQ | FLOW_CTRL_HALT_CPU_FIQ + orrne r0, r0, #FLOW_CTRL_HALT_LIC_IRQ | FLOW_CTRL_HALT_LIC_FIQ + cpu_to_halt_reg r2, r1 str r0, [r6, r2] dsb @@ -167,4 +698,134 @@ /* !!!FIXME!!! Implement halt failure handler */ b halted +/* + * tegra30_sdram_self_refresh + * + * called with MMU off and caches disabled + * must be executed from IRAM + * r4 = TEGRA_PMC_BASE + * r5 = TEGRA_CLK_RESET_BASE + * r6 = TEGRA_FLOW_CTRL_BASE + * r7 = TEGRA_TMRUS_BASE + * r10= SoC ID + */ +tegra30_sdram_self_refresh: + + adr r8, tegra_sdram_pad_save + tegra_get_soc_id TEGRA_APB_MISC_BASE, r10 + cmp r10, #TEGRA30 + adreq r2, tegra30_sdram_pad_address + ldreq r3, tegra30_sdram_pad_size + cmp r10, #TEGRA114 + adreq r2, tegra114_sdram_pad_address + ldreq r3, tegra114_sdram_pad_size + cmp r10, #TEGRA124 + adreq r2, tegra124_sdram_pad_address + ldreq r3, tegra30_sdram_pad_size + + mov r9, #0 + +padsave: + ldr r0, [r2, r9] @ r0 is the addr in the pad_address + + ldr r1, [r0] + str r1, [r8, r9] @ save the content of the addr + + add r9, r9, #4 + cmp r3, r9 + bne padsave +padsave_done: + + dsb + + cmp r10, #TEGRA30 + ldreq r0, =TEGRA_EMC_BASE @ r0 reserved for emc base addr + cmp r10, #TEGRA114 + ldreq r0, =TEGRA_EMC0_BASE + cmp r10, #TEGRA124 + ldreq r0, =TEGRA124_EMC_BASE + +enter_self_refresh: + cmp r10, #TEGRA30 + mov r1, #0 + str r1, [r0, #EMC_ZCAL_INTERVAL] + str r1, [r0, #EMC_AUTO_CAL_INTERVAL] + ldr r1, [r0, #EMC_CFG] + bic r1, r1, #(1 << 28) + bicne r1, r1, #(1 << 29) + str r1, [r0, #EMC_CFG] @ disable DYN_SELF_REF + + emc_timing_update r1, r0 + + ldr r1, [r7] + add r1, r1, #5 + wait_until r1, r7, r2 + +emc_wait_auto_cal: + ldr r1, [r0, #EMC_AUTO_CAL_STATUS] + tst r1, #(1 << 31) @ wait until AUTO_CAL_ACTIVE is cleared + bne emc_wait_auto_cal + + mov r1, #3 + str r1, [r0, #EMC_REQ_CTRL] @ stall incoming DRAM requests + +emcidle: + ldr r1, [r0, #EMC_EMC_STATUS] + tst r1, #4 + beq emcidle + + mov r1, #1 + str r1, [r0, #EMC_SELF_REF] + + emc_device_mask r1, r0 + +emcself: + ldr r2, [r0, #EMC_EMC_STATUS] + and r2, r2, r1 + cmp r2, r1 + bne emcself @ loop until DDR in self-refresh + + /* Put VTTGEN in the lowest power mode */ + ldr r1, [r0, #EMC_XM2VTTGENPADCTRL] + mov32 r2, 0xF8F8FFFF @ clear XM2VTTGEN_DRVUP and XM2VTTGEN_DRVDN + and r1, r1, r2 + str r1, [r0, #EMC_XM2VTTGENPADCTRL] + ldr r1, [r0, #EMC_XM2VTTGENPADCTRL2] + cmp r10, #TEGRA30 + orreq r1, r1, #7 @ set E_NO_VTTGEN + orrne r1, r1, #0x3f + str r1, [r0, #EMC_XM2VTTGENPADCTRL2] + + emc_timing_update r1, r0 + + /* Tegra114 had dual EMC channel, now config the other one */ + cmp r10, #TEGRA114 + bne no_dual_emc_chanl + mov32 r1, TEGRA_EMC1_BASE + cmp r0, r1 + movne r0, r1 + bne enter_self_refresh +no_dual_emc_chanl: + + ldr r1, [r4, #PMC_CTRL] + tst r1, #PMC_CTRL_SIDE_EFFECT_LP0 + bne pmc_io_dpd_skip + /* + * Put DDR_DATA, DISC_ADDR_CMD, DDR_ADDR_CMD, POP_ADDR_CMD, POP_CLK + * and COMP in the lowest power mode when LP1. + */ + mov32 r1, 0x8EC00000 + str r1, [r4, #PMC_IO_DPD_REQ] +pmc_io_dpd_skip: + + dsb + + ret lr + + .ltorg +/* dummy symbol for end of IRAM */ + .align L1_CACHE_SHIFT + .global tegra30_iram_end +tegra30_iram_end: + b . #endif