--- zzzz-none-000/linux-3.10.107/arch/arm/mach-ux500/timer.c	2017-06-27 09:49:32.000000000 +0000
+++ scorpion-7490-727/linux-3.10.107/arch/arm/mach-ux500/timer.c	2021-02-04 17:41:59.000000000 +0000
@@ -10,95 +10,39 @@
 #include <linux/clocksource.h>
 #include <linux/of.h>
 #include <linux/of_address.h>
-#include <linux/platform_data/clocksource-nomadik-mtu.h>
-
-#include <asm/smp_twd.h>
 
 #include "setup.h"
-#include "irqs.h"
 
 #include "db8500-regs.h"
 #include "id.h"
 
-#ifdef CONFIG_HAVE_ARM_TWD
-static DEFINE_TWD_LOCAL_TIMER(u8500_twd_local_timer,
-			      U8500_TWD_BASE, IRQ_LOCALTIMER);
-
-static void __init ux500_twd_init(void)
-{
-	struct twd_local_timer *twd_local_timer;
-	int err;
-
-	/* Use this to switch local timer base if changed in new ASICs */
-	twd_local_timer = &u8500_twd_local_timer;
-
-	if (of_have_populated_dt())
-		clocksource_of_init();
-	else {
-		err = twd_local_timer_register(twd_local_timer);
-		if (err)
-			pr_err("twd_local_timer_register failed %d\n", err);
-	}
-}
-#else
-#define ux500_twd_init()	do { } while(0)
-#endif
-
-const static struct of_device_id prcmu_timer_of_match[] __initconst = {
+static const struct of_device_id prcmu_timer_of_match[] __initconst = {
 	{ .compatible = "stericsson,db8500-prcmu-timer-4", },
 	{ },
 };
 
 void __init ux500_timer_init(void)
 {
-	void __iomem *mtu_timer_base;
 	void __iomem *prcmu_timer_base;
 	void __iomem *tmp_base;
 	struct device_node *np;
 
-	if (cpu_is_u8500_family() || cpu_is_ux540_family()) {
-		mtu_timer_base = __io_address(U8500_MTU0_BASE);
+	if (cpu_is_u8500_family() || cpu_is_ux540_family())
 		prcmu_timer_base = __io_address(U8500_PRCMU_TIMER_4_BASE);
-	} else {
+	else
 		ux500_unknown_soc();
-	}
 
-	/* TODO: Once MTU has been DT:ed place code above into else. */
-	if (of_have_populated_dt()) {
-#ifdef CONFIG_OF
-		np = of_find_matching_node(NULL, prcmu_timer_of_match);
-		if (!np)
-#endif
-			goto dt_fail;
-
-		tmp_base = of_iomap(np, 0);
-		if (!tmp_base)
-			goto dt_fail;
+	np = of_find_matching_node(NULL, prcmu_timer_of_match);
+	if (!np)
+		goto dt_fail;
+
+	tmp_base = of_iomap(np, 0);
+	if (!tmp_base)
+		goto dt_fail;
 
-		prcmu_timer_base = tmp_base;
-	}
+	prcmu_timer_base = tmp_base;
 
 dt_fail:
-	/* Doing it the old fashioned way. */
-
-	/*
-	 * Here we register the timerblocks active in the system.
-	 * Localtimers (twd) is started when both cpu is up and running.
-	 * MTU register a clocksource, clockevent and sched_clock.
-	 * Since the MTU is located in the VAPE power domain
-	 * it will be cleared in sleep which makes it unsuitable.
-	 * We however need it as a timer tick (clockevent)
-	 * during boot to calibrate delay until twd is started.
-	 * RTC-RTT have problems as timer tick during boot since it is
-	 * depending on delay which is not yet calibrated. RTC-RTT is in the
-	 * always-on powerdomain and is used as clockevent instead of twd when
-	 * sleeping.
-	 * The PRCMU timer 4 register a clocksource and
-	 * sched_clock with higher rating then MTU since is always-on.
-	 *
-	 */
-
-	nmdk_timer_init(mtu_timer_base, IRQ_MTU0);
 	clksrc_dbx500_prcmu_init(prcmu_timer_base);
-	ux500_twd_init();
+	clocksource_probe();
 }