--- zzzz-none-000/linux-3.10.107/arch/blackfin/include/asm/bfin_twi.h 2017-06-27 09:49:32.000000000 +0000 +++ scorpion-7490-727/linux-3.10.107/arch/blackfin/include/asm/bfin_twi.h 2021-02-04 17:41:59.000000000 +0000 @@ -9,60 +9,7 @@ #ifndef __ASM_BFIN_TWI_H__ #define __ASM_BFIN_TWI_H__ -#include -#include - -/* - * All Blackfin system MMRs are padded to 32bits even if the register - * itself is only 16bits. So use a helper macro to streamline this. - */ -#define __BFP(m) u16 m; u16 __pad_##m - -/* - * bfin twi registers layout - */ -struct bfin_twi_regs { - __BFP(clkdiv); - __BFP(control); - __BFP(slave_ctl); - __BFP(slave_stat); - __BFP(slave_addr); - __BFP(master_ctl); - __BFP(master_stat); - __BFP(master_addr); - __BFP(int_stat); - __BFP(int_mask); - __BFP(fifo_ctl); - __BFP(fifo_stat); - u32 __pad[20]; - __BFP(xmt_data8); - __BFP(xmt_data16); - __BFP(rcv_data8); - __BFP(rcv_data16); -}; - -#undef __BFP - -struct bfin_twi_iface { - int irq; - spinlock_t lock; - char read_write; - u8 command; - u8 *transPtr; - int readNum; - int writeNum; - int cur_mode; - int manual_stop; - int result; - struct i2c_adapter adap; - struct completion complete; - struct i2c_msg *pmsg; - int msg_num; - int cur_msg; - u16 saved_clkdiv; - u16 saved_control; - struct bfin_twi_regs __iomem *regs_base; -}; +#include #define DEFINE_TWI_REG(reg_name, reg) \ static inline u16 read_##reg_name(struct bfin_twi_iface *iface) \ @@ -71,7 +18,6 @@ { bfin_write16(&iface->regs_base->reg, v); } DEFINE_TWI_REG(CLKDIV, clkdiv) -DEFINE_TWI_REG(CONTROL, control) DEFINE_TWI_REG(SLAVE_CTL, slave_ctl) DEFINE_TWI_REG(SLAVE_STAT, slave_stat) DEFINE_TWI_REG(SLAVE_ADDR, slave_addr) @@ -80,7 +26,6 @@ DEFINE_TWI_REG(MASTER_ADDR, master_addr) DEFINE_TWI_REG(INT_STAT, int_stat) DEFINE_TWI_REG(INT_MASK, int_mask) -DEFINE_TWI_REG(FIFO_CTL, fifo_ctl) DEFINE_TWI_REG(FIFO_STAT, fifo_stat) DEFINE_TWI_REG(XMT_DATA8, xmt_data8) DEFINE_TWI_REG(XMT_DATA16, xmt_data16) @@ -113,75 +58,25 @@ } #endif +static inline u16 read_FIFO_CTL(struct bfin_twi_iface *iface) +{ + return bfin_read16(&iface->regs_base->fifo_ctl); +} + +static inline void write_FIFO_CTL(struct bfin_twi_iface *iface, u16 v) +{ + bfin_write16(&iface->regs_base->fifo_ctl, v); + SSYNC(); +} -/* ******************** TWO-WIRE INTERFACE (TWI) MASKS ***********************/ -/* TWI_CLKDIV Macros (Use: *pTWI_CLKDIV = CLKLOW(x)|CLKHI(y); ) */ -#define CLKLOW(x) ((x) & 0xFF) /* Periods Clock Is Held Low */ -#define CLKHI(y) (((y)&0xFF)<<0x8) /* Periods Before New Clock Low */ - -/* TWI_PRESCALE Masks */ -#define PRESCALE 0x007F /* SCLKs Per Internal Time Reference (10MHz) */ -#define TWI_ENA 0x0080 /* TWI Enable */ -#define SCCB 0x0200 /* SCCB Compatibility Enable */ - -/* TWI_SLAVE_CTL Masks */ -#define SEN 0x0001 /* Slave Enable */ -#define SADD_LEN 0x0002 /* Slave Address Length */ -#define STDVAL 0x0004 /* Slave Transmit Data Valid */ -#define NAK 0x0008 /* NAK/ACK* Generated At Conclusion Of Transfer */ -#define GEN 0x0010 /* General Call Address Matching Enabled */ - -/* TWI_SLAVE_STAT Masks */ -#define SDIR 0x0001 /* Slave Transfer Direction (Transmit/Receive*) */ -#define GCALL 0x0002 /* General Call Indicator */ - -/* TWI_MASTER_CTL Masks */ -#define MEN 0x0001 /* Master Mode Enable */ -#define MADD_LEN 0x0002 /* Master Address Length */ -#define MDIR 0x0004 /* Master Transmit Direction (RX/TX*) */ -#define FAST 0x0008 /* Use Fast Mode Timing Specs */ -#define STOP 0x0010 /* Issue Stop Condition */ -#define RSTART 0x0020 /* Repeat Start or Stop* At End Of Transfer */ -#define DCNT 0x3FC0 /* Data Bytes To Transfer */ -#define SDAOVR 0x4000 /* Serial Data Override */ -#define SCLOVR 0x8000 /* Serial Clock Override */ - -/* TWI_MASTER_STAT Masks */ -#define MPROG 0x0001 /* Master Transfer In Progress */ -#define LOSTARB 0x0002 /* Lost Arbitration Indicator (Xfer Aborted) */ -#define ANAK 0x0004 /* Address Not Acknowledged */ -#define DNAK 0x0008 /* Data Not Acknowledged */ -#define BUFRDERR 0x0010 /* Buffer Read Error */ -#define BUFWRERR 0x0020 /* Buffer Write Error */ -#define SDASEN 0x0040 /* Serial Data Sense */ -#define SCLSEN 0x0080 /* Serial Clock Sense */ -#define BUSBUSY 0x0100 /* Bus Busy Indicator */ - -/* TWI_INT_SRC and TWI_INT_ENABLE Masks */ -#define SINIT 0x0001 /* Slave Transfer Initiated */ -#define SCOMP 0x0002 /* Slave Transfer Complete */ -#define SERR 0x0004 /* Slave Transfer Error */ -#define SOVF 0x0008 /* Slave Overflow */ -#define MCOMP 0x0010 /* Master Transfer Complete */ -#define MERR 0x0020 /* Master Transfer Error */ -#define XMTSERV 0x0040 /* Transmit FIFO Service */ -#define RCVSERV 0x0080 /* Receive FIFO Service */ - -/* TWI_FIFO_CTRL Masks */ -#define XMTFLUSH 0x0001 /* Transmit Buffer Flush */ -#define RCVFLUSH 0x0002 /* Receive Buffer Flush */ -#define XMTINTLEN 0x0004 /* Transmit Buffer Interrupt Length */ -#define RCVINTLEN 0x0008 /* Receive Buffer Interrupt Length */ - -/* TWI_FIFO_STAT Masks */ -#define XMTSTAT 0x0003 /* Transmit FIFO Status */ -#define XMT_EMPTY 0x0000 /* Transmit FIFO Empty */ -#define XMT_HALF 0x0001 /* Transmit FIFO Has 1 Byte To Write */ -#define XMT_FULL 0x0003 /* Transmit FIFO Full (2 Bytes To Write) */ - -#define RCVSTAT 0x000C /* Receive FIFO Status */ -#define RCV_EMPTY 0x0000 /* Receive FIFO Empty */ -#define RCV_HALF 0x0004 /* Receive FIFO Has 1 Byte To Read */ -#define RCV_FULL 0x000C /* Receive FIFO Full (2 Bytes To Read) */ +static inline u16 read_CONTROL(struct bfin_twi_iface *iface) +{ + return bfin_read16(&iface->regs_base->control); +} +static inline void write_CONTROL(struct bfin_twi_iface *iface, u16 v) +{ + SSYNC(); + bfin_write16(&iface->regs_base->control, v); +} #endif