--- zzzz-none-000/linux-3.10.107/arch/blackfin/mach-bf518/boards/ezbrd.c	2017-06-27 09:49:32.000000000 +0000
+++ scorpion-7490-727/linux-3.10.107/arch/blackfin/mach-bf518/boards/ezbrd.c	2021-02-04 17:41:59.000000000 +0000
@@ -36,7 +36,7 @@
  *  Driver needs to know address, irq and flag pin.
  */
 
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
 static struct mtd_partition ezbrd_partitions[] = {
 	{
 		.name       = "bootloader(nor)",
@@ -61,7 +61,7 @@
 
 static struct resource ezbrd_flash_resource = {
 	.start = 0x20000000,
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 	.end   = 0x202fffff,
 #else
 	.end   = 0x203fffff,
@@ -80,14 +80,14 @@
 };
 #endif
 
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 static struct platform_device rtc_device = {
 	.name = "rtc-bfin",
 	.id   = -1,
 };
 #endif
 
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
 #include <linux/bfin_mac.h>
 static const unsigned short bfin_mac_peripherals[] = {
 	P_MII0_ETxD0,
@@ -105,7 +105,7 @@
 
 static struct bfin_phydev_platform_data bfin_phydev_data[] = {
 	{
-#if defined(CONFIG_NET_DSA_KSZ8893M) || defined(CONFIG_NET_DSA_KSZ8893M_MODULE)
+#if IS_ENABLED(CONFIG_NET_DSA_KSZ8893M)
 		.addr = 3,
 #else
 		.addr = 1,
@@ -119,7 +119,7 @@
 	.phydev_data = bfin_phydev_data,
 	.phy_mode = PHY_INTERFACE_MODE_MII,
 	.mac_peripherals = bfin_mac_peripherals,
-#if defined(CONFIG_NET_DSA_KSZ8893M) || defined(CONFIG_NET_DSA_KSZ8893M_MODULE)
+#if IS_ENABLED(CONFIG_NET_DSA_KSZ8893M)
 	.phy_mask = 0xfff7, /* Only probe the port phy connect to the on chip MAC */
 #endif
 	.vlan1_mask = 1,
@@ -140,7 +140,7 @@
 	}
 };
 
-#if defined(CONFIG_NET_DSA_KSZ8893M) || defined(CONFIG_NET_DSA_KSZ8893M_MODULE)
+#if IS_ENABLED(CONFIG_NET_DSA_KSZ8893M)
 static struct dsa_chip_data ksz8893m_switch_chip_data = {
 	.mii_bus = &bfin_mii_bus.dev,
 	.port_names = {
@@ -165,8 +165,7 @@
 #endif
 #endif
 
-#if defined(CONFIG_MTD_M25P80) \
-	|| defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
 static struct mtd_partition bfin_spi_flash_partitions[] = {
 	{
 		.name = "bootloader(spi)",
@@ -193,13 +192,13 @@
 };
 #endif
 
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
 static struct bfin5xx_spi_chip mmc_spi_chip_info = {
 	.enable_dma = 0,
 };
 #endif
 
-#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7877)
 static const struct ad7877_platform_data bfin_ad7877_ts_info = {
 	.model			= 7877,
 	.vref_delay_usecs	= 50,	/* internal, no capacitor */
@@ -216,8 +215,7 @@
 #endif
 
 static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) \
-	|| defined(CONFIG_MTD_M25P80_MODULE)
+#if IS_ENABLED(CONFIG_MTD_M25P80)
 	{
 		/* the modalias must be the same as spi device driver name */
 		.modalias = "m25p80", /* Name of spi_driver for this device */
@@ -230,9 +228,8 @@
 	},
 #endif
 
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
-#if defined(CONFIG_NET_DSA_KSZ8893M) \
-	|| defined(CONFIG_NET_DSA_KSZ8893M_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
+#if IS_ENABLED(CONFIG_NET_DSA_KSZ8893M)
 	{
 		.modalias = "ksz8893m",
 		.max_speed_hz = 5000000,
@@ -244,7 +241,7 @@
 #endif
 #endif
 
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
 	{
 		.modalias = "mmc_spi",
 		.max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
@@ -254,7 +251,7 @@
 		.mode = SPI_MODE_3,
 	},
 #endif
-#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7877)
 	{
 		.modalias		= "ad7877",
 		.platform_data		= &bfin_ad7877_ts_info,
@@ -264,7 +261,7 @@
 		.chip_select  = 2,
 	},
 #endif
-#if defined(CONFIG_SND_SOC_WM8731) || defined(CONFIG_SND_SOC_WM8731_MODULE) \
+#if IS_ENABLED(CONFIG_SND_SOC_WM8731) \
 	 && defined(CONFIG_SND_SOC_WM8731_SPI)
 	{
 		.modalias	= "wm8731",
@@ -274,7 +271,7 @@
 		.mode = SPI_MODE_0,
 	},
 #endif
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+#if IS_ENABLED(CONFIG_SPI_SPIDEV)
 	{
 		.modalias = "spidev",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
@@ -282,7 +279,7 @@
 		.chip_select = 1,
 	},
 #endif
-#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+#if IS_ENABLED(CONFIG_FB_BFIN_LQ035Q1)
 	{
 		.modalias = "bfin-lq035q1-spi",
 		.max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
@@ -294,7 +291,7 @@
 };
 
 /* SPI controller data */
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 /* SPI (0) */
 static struct bfin5xx_spi_master bfin_spi0_info = {
 	.num_chipselect = 6,
@@ -366,7 +363,7 @@
 };
 #endif  /* spi master and devices */
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 static struct resource bfin_uart0_resources[] = {
 	{
@@ -465,7 +462,7 @@
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 static struct resource bfin_sir0_resources[] = {
 	{
@@ -520,7 +517,7 @@
 #endif
 #endif
 
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
 static struct platform_device bfin_i2s = {
 	.name = "bfin-i2s",
 	.id = CONFIG_SND_BF5XX_SPORT_NUM,
@@ -528,7 +525,7 @@
 };
 #endif
 
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
 static const u16 bfin_twi0_pins[] = {P_TWI0_SCL, P_TWI0_SDA, 0};
 
 static struct resource bfin_twi0_resource[] = {
@@ -556,25 +553,25 @@
 #endif
 
 static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
-#if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_TWI_LCD)
 	{
 		I2C_BOARD_INFO("pcf8574_lcd", 0x22),
 	},
 #endif
-#if defined(CONFIG_INPUT_PCF8574) || defined(CONFIG_INPUT_PCF8574_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_PCF8574)
 	{
 		I2C_BOARD_INFO("pcf8574_keypad", 0x27),
 		.irq = IRQ_PF8,
 	},
 #endif
-#if defined(CONFIG_SND_SOC_SSM2602) || defined(CONFIG_SND_SOC_SSM2602_MODULE)
+#if IS_ENABLED(CONFIG_SND_SOC_SSM2602)
 	{
 		I2C_BOARD_INFO("ssm2602", 0x1b),
 	},
 #endif
 };
 
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 static struct resource bfin_sport0_uart_resources[] = {
 	{
@@ -645,7 +642,7 @@
 #endif
 #endif
 
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
 #include <linux/input.h>
 #include <linux/gpio_keys.h>
 
@@ -667,7 +664,7 @@
 };
 #endif
 
-#if defined(CONFIG_SDH_BFIN) || defined(CONFIG_SDH_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SDH_BFIN)
 
 static struct bfin_sd_host bfin_sdh_data = {
 	.dma_chan = CH_RSI,
@@ -710,24 +707,24 @@
 
 	&bfin_dpmc,
 
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 	&rtc_device,
 #endif
 
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_MAC)
 	&bfin_mii_bus,
 	&bfin_mac_device,
-#if defined(CONFIG_NET_DSA_KSZ8893M) || defined(CONFIG_NET_DSA_KSZ8893M_MODULE)
+#if IS_ENABLED(CONFIG_NET_DSA_KSZ8893M)
 	&ksz8893m_switch_device,
 #endif
 #endif
 
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 	&bfin_spi0_device,
 	&bfin_spi1_device,
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 	&bfin_uart0_device,
 #endif
@@ -736,7 +733,7 @@
 #endif
 #endif
 
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 	&bfin_sir0_device,
 #endif
@@ -745,15 +742,15 @@
 #endif
 #endif
 
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
 	&i2c_bfin_twi_device,
 #endif
 
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+#if IS_ENABLED(CONFIG_SND_BF5XX_I2S)
 	&bfin_i2s,
 #endif
 
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 	&bfin_sport0_uart_device,
 #endif
@@ -762,15 +759,15 @@
 #endif
 #endif
 
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
 	&bfin_device_gpiokeys,
 #endif
 
-#if defined(CONFIG_SDH_BFIN) || defined(CONFIG_SDH_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SDH_BFIN)
 	&bf51x_sdh_device,
 #endif
 
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
 	&ezbrd_flash_device,
 #endif
 };
@@ -784,7 +781,7 @@
 	spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
 	/* setup BF518-EZBRD GPIO pin PG11 to AMS2, PG15 to AMS3. */
 	peripheral_request(P_AMS2, "ParaFlash");
-#if !defined(CONFIG_SPI_BFIN5XX) && !defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if !IS_ENABLED(CONFIG_SPI_BFIN5XX)
 	peripheral_request(P_AMS3, "ParaFlash");
 #endif
 	return 0;