--- zzzz-none-000/linux-3.10.107/arch/m32r/include/asm/barrier.h	2017-06-27 09:49:32.000000000 +0000
+++ scorpion-7490-727/linux-3.10.107/arch/m32r/include/asm/barrier.h	2021-02-04 17:41:59.000000000 +0000
@@ -11,84 +11,6 @@
 
 #define nop()  __asm__ __volatile__ ("nop" : : )
 
-/*
- * Memory barrier.
- *
- * mb() prevents loads and stores being reordered across this point.
- * rmb() prevents loads being reordered across this point.
- * wmb() prevents stores being reordered across this point.
- */
-#define mb()   barrier()
-#define rmb()  mb()
-#define wmb()  mb()
-
-/**
- * read_barrier_depends - Flush all pending reads that subsequents reads
- * depend on.
- *
- * No data-dependent reads from memory-like regions are ever reordered
- * over this barrier.  All reads preceding this primitive are guaranteed
- * to access memory (but not necessarily other CPUs' caches) before any
- * reads following this primitive that depend on the data return by
- * any of the preceding reads.  This primitive is much lighter weight than
- * rmb() on most CPUs, and is never heavier weight than is
- * rmb().
- *
- * These ordering constraints are respected by both the local CPU
- * and the compiler.
- *
- * Ordering is not guaranteed by anything other than these primitives,
- * not even by data dependencies.  See the documentation for
- * memory_barrier() for examples and URLs to more information.
- *
- * For example, the following code would force ordering (the initial
- * value of "a" is zero, "b" is one, and "p" is "&a"):
- *
- * <programlisting>
- *      CPU 0                           CPU 1
- *
- *      b = 2;
- *      memory_barrier();
- *      p = &b;                         q = p;
- *                                      read_barrier_depends();
- *                                      d = *q;
- * </programlisting>
- *
- *
- * because the read of "*q" depends on the read of "p" and these
- * two reads are separated by a read_barrier_depends().  However,
- * the following code, with the same initial values for "a" and "b":
- *
- * <programlisting>
- *      CPU 0                           CPU 1
- *
- *      a = 2;
- *      memory_barrier();
- *      b = 3;                          y = b;
- *                                      read_barrier_depends();
- *                                      x = a;
- * </programlisting>
- *
- * does not enforce ordering, since there is no data dependency between
- * the read of "a" and the read of "b".  Therefore, on some CPUs, such
- * as Alpha, "y" could be set to 3 and "x" to 0.  Use rmb()
- * in cases like this where there are no data dependencies.
- **/
-
-#define read_barrier_depends()	do { } while (0)
-
-#ifdef CONFIG_SMP
-#define smp_mb()	mb()
-#define smp_rmb()	rmb()
-#define smp_wmb()	wmb()
-#define smp_read_barrier_depends()	read_barrier_depends()
-#define set_mb(var, value) do { (void) xchg(&var, value); } while (0)
-#else
-#define smp_mb()	barrier()
-#define smp_rmb()	barrier()
-#define smp_wmb()	barrier()
-#define smp_read_barrier_depends()	do { } while (0)
-#define set_mb(var, value) do { var = value; barrier(); } while (0)
-#endif
+#include <asm-generic/barrier.h>
 
 #endif /* _ASM_M32R_BARRIER_H */