--- zzzz-none-000/linux-3.10.107/arch/mips/alchemy/common/setup.c	2017-06-27 09:49:32.000000000 +0000
+++ scorpion-7490-727/linux-3.10.107/arch/mips/alchemy/common/setup.c	2021-02-04 17:41:59.000000000 +0000
@@ -27,30 +27,18 @@
 
 #include <linux/init.h>
 #include <linux/ioport.h>
-#include <linux/jiffies.h>
-#include <linux/module.h>
 
+#include <asm/dma-coherence.h>
 #include <asm/mipsregs.h>
-#include <asm/time.h>
 
 #include <au1000.h>
 
 extern void __init board_setup(void);
-extern void set_cpuspec(void);
+extern void __init alchemy_set_lpj(void);
 
 void __init plat_mem_setup(void)
 {
-	unsigned long est_freq;
-
-	/* determine core clock */
-	est_freq = au1xxx_calc_clock();
-	est_freq += 5000;    /* round */
-	est_freq -= est_freq % 10000;
-	printk(KERN_INFO "(PRId %08x) @ %lu.%02lu MHz\n", read_c0_prid(),
-	       est_freq / 1000000, ((est_freq % 1000000) * 100) / 1000000);
-
-	/* this is faster than wasting cycles trying to approximate it */
-	preset_lpj = (est_freq >> 1) / HZ;
+	alchemy_set_lpj();
 
 	if (au1xxx_cpu_needs_config_od())
 		/* Various early Au1xx0 errata corrected by this */
@@ -59,6 +47,21 @@
 		/* Clear to obtain best system bus performance */
 		clear_c0_config(1 << 19); /* Clear Config[OD] */
 
+	hw_coherentio = 0;
+	coherentio = 1;
+	switch (alchemy_get_cputype()) {
+	case ALCHEMY_CPU_AU1000:
+	case ALCHEMY_CPU_AU1500:
+	case ALCHEMY_CPU_AU1100:
+		coherentio = 0;
+		break;
+	case ALCHEMY_CPU_AU1200:
+		/* Au1200 AB USB does not support coherent memory */
+		if (0 == (read_c0_prid() & PRID_REV_MASK))
+			coherentio = 0;
+		break;
+	}
+
 	board_setup();	/* board specific setup */
 
 	/* IO/MEM resources. */
@@ -69,9 +72,9 @@
 	iomem_resource.end = IOMEM_RESOURCE_END;
 }
 
-#if defined(CONFIG_64BIT_PHYS_ADDR) && defined(CONFIG_PCI)
+#if defined(CONFIG_PHYS_ADDR_T_64BIT) && defined(CONFIG_PCI)
 /* This routine should be valid for all Au1x based boards */
-phys_t __fixup_bigphys_addr(phys_t phys_addr, phys_t size)
+phys_addr_t __fixup_bigphys_addr(phys_addr_t phys_addr, phys_addr_t size)
 {
 	unsigned long start = ALCHEMY_PCI_MEMWIN_START;
 	unsigned long end = ALCHEMY_PCI_MEMWIN_END;
@@ -82,7 +85,7 @@
 
 	/* Check for PCI memory window */
 	if (phys_addr >= start && (phys_addr + size - 1) <= end)
-		return (phys_t)(AU1500_PCI_MEM_PHYS_ADDR + phys_addr);
+		return (phys_addr_t)(AU1500_PCI_MEM_PHYS_ADDR + phys_addr);
 
 	/* default nop */
 	return phys_addr;