--- zzzz-none-000/linux-3.10.107/arch/mips/alchemy/devboards/db1200.c 2017-06-27 09:49:32.000000000 +0000 +++ scorpion-7490-727/linux-3.10.107/arch/mips/alchemy/devboards/db1200.c 2021-02-04 17:41:59.000000000 +0000 @@ -18,6 +18,7 @@ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA */ +#include #include #include #include @@ -35,16 +36,63 @@ #include #include #include +#include #include #include #include +#include #include #include #include -#include #include "platform.h" +#define BCSR_INT_IDE 0x0001 +#define BCSR_INT_ETH 0x0002 +#define BCSR_INT_PC0 0x0004 +#define BCSR_INT_PC0STSCHG 0x0008 +#define BCSR_INT_PC1 0x0010 +#define BCSR_INT_PC1STSCHG 0x0020 +#define BCSR_INT_DC 0x0040 +#define BCSR_INT_FLASHBUSY 0x0080 +#define BCSR_INT_PC0INSERT 0x0100 +#define BCSR_INT_PC0EJECT 0x0200 +#define BCSR_INT_PC1INSERT 0x0400 +#define BCSR_INT_PC1EJECT 0x0800 +#define BCSR_INT_SD0INSERT 0x1000 +#define BCSR_INT_SD0EJECT 0x2000 +#define BCSR_INT_SD1INSERT 0x4000 +#define BCSR_INT_SD1EJECT 0x8000 + +#define DB1200_IDE_PHYS_ADDR 0x18800000 +#define DB1200_IDE_REG_SHIFT 5 +#define DB1200_IDE_PHYS_LEN (16 << DB1200_IDE_REG_SHIFT) +#define DB1200_ETH_PHYS_ADDR 0x19000300 +#define DB1200_NAND_PHYS_ADDR 0x20000000 + +#define PB1200_IDE_PHYS_ADDR 0x0C800000 +#define PB1200_ETH_PHYS_ADDR 0x0D000300 +#define PB1200_NAND_PHYS_ADDR 0x1C000000 + +#define DB1200_INT_BEGIN (AU1000_MAX_INTR + 1) +#define DB1200_IDE_INT (DB1200_INT_BEGIN + 0) +#define DB1200_ETH_INT (DB1200_INT_BEGIN + 1) +#define DB1200_PC0_INT (DB1200_INT_BEGIN + 2) +#define DB1200_PC0_STSCHG_INT (DB1200_INT_BEGIN + 3) +#define DB1200_PC1_INT (DB1200_INT_BEGIN + 4) +#define DB1200_PC1_STSCHG_INT (DB1200_INT_BEGIN + 5) +#define DB1200_DC_INT (DB1200_INT_BEGIN + 6) +#define DB1200_FLASHBUSY_INT (DB1200_INT_BEGIN + 7) +#define DB1200_PC0_INSERT_INT (DB1200_INT_BEGIN + 8) +#define DB1200_PC0_EJECT_INT (DB1200_INT_BEGIN + 9) +#define DB1200_PC1_INSERT_INT (DB1200_INT_BEGIN + 10) +#define DB1200_PC1_EJECT_INT (DB1200_INT_BEGIN + 11) +#define DB1200_SD0_INSERT_INT (DB1200_INT_BEGIN + 12) +#define DB1200_SD0_EJECT_INT (DB1200_INT_BEGIN + 13) +#define PB1200_SD1_INSERT_INT (DB1200_INT_BEGIN + 14) +#define PB1200_SD1_EJECT_INT (DB1200_INT_BEGIN + 15) +#define DB1200_INT_END (DB1200_INT_BEGIN + 15) + const char *get_system_type(void); static int __init db1200_detect_board(void) @@ -82,45 +130,25 @@ int __init db1200_board_setup(void) { - unsigned long freq0, clksrc, div, pfc; unsigned short whoami; if (db1200_detect_board()) return -ENODEV; whoami = bcsr_read(BCSR_WHOAMI); + switch (BCSR_WHOAMI_BOARD(whoami)) { + case BCSR_WHOAMI_PB1200_DDR1: + case BCSR_WHOAMI_PB1200_DDR2: + case BCSR_WHOAMI_DB1200: + break; + default: + return -ENODEV; + } + printk(KERN_INFO "Alchemy/AMD/RMI %s Board, CPLD Rev %d" " Board-ID %d Daughtercard ID %d\n", get_system_type(), (whoami >> 4) & 0xf, (whoami >> 8) & 0xf, whoami & 0xf); - /* SMBus/SPI on PSC0, Audio on PSC1 */ - pfc = __raw_readl((void __iomem *)SYS_PINFUNC); - pfc &= ~(SYS_PINFUNC_P0A | SYS_PINFUNC_P0B); - pfc &= ~(SYS_PINFUNC_P1A | SYS_PINFUNC_P1B | SYS_PINFUNC_FS3); - pfc |= SYS_PINFUNC_P1C; /* SPI is configured later */ - __raw_writel(pfc, (void __iomem *)SYS_PINFUNC); - wmb(); - - /* Clock configurations: PSC0: ~50MHz via Clkgen0, derived from - * CPU clock; all other clock generators off/unused. - */ - div = (get_au1x00_speed() + 25000000) / 50000000; - if (div & 1) - div++; - div = ((div >> 1) - 1) & 0xff; - - freq0 = div << SYS_FC_FRDIV0_BIT; - __raw_writel(freq0, (void __iomem *)SYS_FREQCTRL0); - wmb(); - freq0 |= SYS_FC_FE0; /* enable F0 */ - __raw_writel(freq0, (void __iomem *)SYS_FREQCTRL0); - wmb(); - - /* psc0_intclk comes 1:1 from F0 */ - clksrc = SYS_CS_MUX_FQ0 << SYS_CS_ME0_BIT; - __raw_writel(clksrc, (void __iomem *)SYS_CLKSRC); - wmb(); - return 0; } @@ -194,7 +222,7 @@ static int au1200_nand_device_ready(struct mtd_info *mtd) { - return __raw_readl((void __iomem *)MEM_STSTAT) & 1; + return alchemy_rdsmem(AU1000_MEM_STSTAT) & 1; } static struct mtd_partition db1200_nand_parts[] = { @@ -275,32 +303,38 @@ /**********************************************************************/ +static struct pata_platform_info db1200_ide_info = { + .ioport_shift = DB1200_IDE_REG_SHIFT, +}; + +#define IDE_ALT_START (14 << DB1200_IDE_REG_SHIFT) static struct resource db1200_ide_res[] = { [0] = { .start = DB1200_IDE_PHYS_ADDR, - .end = DB1200_IDE_PHYS_ADDR + DB1200_IDE_PHYS_LEN - 1, + .end = DB1200_IDE_PHYS_ADDR + IDE_ALT_START - 1, .flags = IORESOURCE_MEM, }, [1] = { + .start = DB1200_IDE_PHYS_ADDR + IDE_ALT_START, + .end = DB1200_IDE_PHYS_ADDR + DB1200_IDE_PHYS_LEN - 1, + .flags = IORESOURCE_MEM, + }, + [2] = { .start = DB1200_IDE_INT, .end = DB1200_IDE_INT, .flags = IORESOURCE_IRQ, }, - [2] = { - .start = AU1200_DSCR_CMD0_DMA_REQ1, - .end = AU1200_DSCR_CMD0_DMA_REQ1, - .flags = IORESOURCE_DMA, - }, }; static u64 au1200_ide_dmamask = DMA_BIT_MASK(32); static struct platform_device db1200_ide_dev = { - .name = "au1200-ide", + .name = "pata_platform", .id = 0, .dev = { .dma_mask = &au1200_ide_dmamask, .coherent_dma_mask = DMA_BIT_MASK(32), + .platform_data = &db1200_ide_info, }, .num_resources = ARRAY_SIZE(db1200_ide_res), .resource = db1200_ide_res, @@ -785,6 +819,7 @@ unsigned long pfc; unsigned short sw; int swapped, bid; + struct clk *c; bid = BCSR_WHOAMI_BOARD(bcsr_read(BCSR_WHOAMI)); if ((bid == BCSR_WHOAMI_PB1200_DDR1) || @@ -797,6 +832,25 @@ irq_set_irq_type(AU1200_GPIO7_INT, IRQ_TYPE_LEVEL_LOW); bcsr_init_irq(DB1200_INT_BEGIN, DB1200_INT_END, AU1200_GPIO7_INT); + /* SMBus/SPI on PSC0, Audio on PSC1 */ + pfc = alchemy_rdsys(AU1000_SYS_PINFUNC); + pfc &= ~(SYS_PINFUNC_P0A | SYS_PINFUNC_P0B); + pfc &= ~(SYS_PINFUNC_P1A | SYS_PINFUNC_P1B | SYS_PINFUNC_FS3); + pfc |= SYS_PINFUNC_P1C; /* SPI is configured later */ + alchemy_wrsys(pfc, AU1000_SYS_PINFUNC); + + /* get 50MHz for I2C driver on PSC0 */ + c = clk_get(NULL, "psc0_intclk"); + if (!IS_ERR(c)) { + pfc = clk_round_rate(c, 50000000); + if ((pfc < 1) || (abs(50000000 - pfc) > 2500000)) + pr_warn("DB1200: cant get I2C close to 50MHz\n"); + else + clk_set_rate(c, pfc); + clk_prepare_enable(c); + clk_put(c); + } + /* insert/eject pairs: one of both is always screaming. To avoid * issues they must not be automatically enabled when initially * requested. @@ -824,7 +878,7 @@ * As a result, in SPI mode, OTG simply won't work (PSC0 uses * it as an input pin which is pulled high on the boards). */ - pfc = __raw_readl((void __iomem *)SYS_PINFUNC) & ~SYS_PINFUNC_P0A; + pfc = alchemy_rdsys(AU1000_SYS_PINFUNC) & ~SYS_PINFUNC_P0A; /* switch off OTG VBUS supply */ gpio_request(215, "otg-vbus"); @@ -850,8 +904,7 @@ printk(KERN_INFO " S6.8 ON : PSC0 mode SPI\n"); printk(KERN_INFO " OTG port VBUS supply disabled\n"); } - __raw_writel(pfc, (void __iomem *)SYS_PINFUNC); - wmb(); + alchemy_wrsys(pfc, AU1000_SYS_PINFUNC); /* Audio: DIP7 selects I2S(0)/AC97(1), but need I2C for I2S! * so: DIP7=1 || DIP8=0 => AC97, DIP7=0 && DIP8=1 => I2S