--- zzzz-none-000/linux-3.10.107/arch/mips/ath79/mach-ap136.c 2017-06-27 09:49:32.000000000 +0000 +++ scorpion-7490-727/linux-3.10.107/arch/mips/ath79/mach-ap136.c 2021-02-04 17:41:59.000000000 +0000 @@ -18,23 +18,29 @@ * */ -#include -#include +#include +#include -#include "machtypes.h" +#include + +#include "common.h" +#include "pci.h" +#include "dev-ap9x-pci.h" #include "dev-gpio-buttons.h" +#include "dev-eth.h" #include "dev-leds-gpio.h" -#include "dev-spi.h" +#include "dev-m25p80.h" +#include "dev-nfc.h" #include "dev-usb.h" #include "dev-wmac.h" -#include "pci.h" +#include "machtypes.h" -#define AP136_GPIO_LED_STATUS_RED 14 -#define AP136_GPIO_LED_STATUS_GREEN 19 #define AP136_GPIO_LED_USB 4 -#define AP136_GPIO_LED_WLAN_2G 13 #define AP136_GPIO_LED_WLAN_5G 12 +#define AP136_GPIO_LED_WLAN_2G 13 +#define AP136_GPIO_LED_STATUS_RED 14 #define AP136_GPIO_LED_WPS_RED 15 +#define AP136_GPIO_LED_STATUS_GREEN 19 #define AP136_GPIO_LED_WPS_GREEN 20 #define AP136_GPIO_BTN_WPS 16 @@ -43,37 +49,39 @@ #define AP136_KEYS_POLL_INTERVAL 20 /* msecs */ #define AP136_KEYS_DEBOUNCE_INTERVAL (3 * AP136_KEYS_POLL_INTERVAL) -#define AP136_WMAC_CALDATA_OFFSET 0x1000 -#define AP136_PCIE_CALDATA_OFFSET 0x5000 +#define AP136_MAC0_OFFSET 0 +#define AP136_MAC1_OFFSET 6 +#define AP136_WMAC_CALDATA_OFFSET 0x1000 +#define AP136_PCIE_CALDATA_OFFSET 0x5000 static struct gpio_led ap136_leds_gpio[] __initdata = { { - .name = "qca:green:status", + .name = "ap136:green:status", .gpio = AP136_GPIO_LED_STATUS_GREEN, .active_low = 1, }, { - .name = "qca:red:status", + .name = "ap136:red:status", .gpio = AP136_GPIO_LED_STATUS_RED, .active_low = 1, }, { - .name = "qca:green:wps", + .name = "ap136:green:wps", .gpio = AP136_GPIO_LED_WPS_GREEN, .active_low = 1, }, { - .name = "qca:red:wps", + .name = "ap136:red:wps", .gpio = AP136_GPIO_LED_WPS_RED, .active_low = 1, }, { - .name = "qca:red:wlan-2g", + .name = "ap136:red:wlan-2g", .gpio = AP136_GPIO_LED_WLAN_2G, .active_low = 1, }, { - .name = "qca:red:usb", + .name = "ap136:red:usb", .gpio = AP136_GPIO_LED_USB, .active_low = 1, } @@ -98,59 +106,151 @@ }, }; -static struct spi_board_info ap136_spi_info[] = { - { - .bus_num = 0, - .chip_select = 0, - .max_speed_hz = 25000000, - .modalias = "mx25l6405d", - } +static struct ar8327_pad_cfg ap136_ar8327_pad0_cfg; +static struct ar8327_pad_cfg ap136_ar8327_pad6_cfg; + +static struct ar8327_platform_data ap136_ar8327_data = { + .pad0_cfg = &ap136_ar8327_pad0_cfg, + .pad6_cfg = &ap136_ar8327_pad6_cfg, + .port0_cfg = { + .force_link = 1, + .speed = AR8327_PORT_SPEED_1000, + .duplex = 1, + .txpause = 1, + .rxpause = 1, + }, + .port6_cfg = { + .force_link = 1, + .speed = AR8327_PORT_SPEED_1000, + .duplex = 1, + .txpause = 1, + .rxpause = 1, + }, }; -static struct ath79_spi_platform_data ap136_spi_data = { - .bus_num = 0, - .num_chipselect = 1, +static struct mdio_board_info ap136_mdio0_info[] = { + { + .bus_id = "ag71xx-mdio.0", + .phy_addr = 0, + .platform_data = &ap136_ar8327_data, + }, }; -#ifdef CONFIG_PCI -static struct ath9k_platform_data ap136_ath9k_data; +static void __init ap136_common_setup(void) +{ + u8 *art = (u8 *) KSEG1ADDR(0x1fff0000); + + ath79_register_m25p80(NULL); + + ath79_register_leds_gpio(-1, ARRAY_SIZE(ap136_leds_gpio), + ap136_leds_gpio); + ath79_register_gpio_keys_polled(-1, AP136_KEYS_POLL_INTERVAL, + ARRAY_SIZE(ap136_gpio_keys), + ap136_gpio_keys); + + ath79_register_usb(); + ath79_register_nfc(); + + ath79_register_wmac(art + AP136_WMAC_CALDATA_OFFSET, NULL); + + ath79_setup_qca955x_eth_cfg(QCA955X_ETH_CFG_RGMII_EN); -static int ap136_pci_plat_dev_init(struct pci_dev *dev) + ath79_register_mdio(0, 0x0); + ath79_init_mac(ath79_eth0_data.mac_addr, art + AP136_MAC0_OFFSET, 0); + + mdiobus_register_board_info(ap136_mdio0_info, + ARRAY_SIZE(ap136_mdio0_info)); + + /* GMAC0 is connected to the RMGII interface */ + ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_RGMII; + ath79_eth0_data.phy_mask = BIT(0); + ath79_eth0_data.mii_bus_dev = &ath79_mdio0_device.dev; + + ath79_register_eth(0); + + /* GMAC1 is connected tot eh SGMII interface */ + ath79_eth1_data.phy_if_mode = PHY_INTERFACE_MODE_SGMII; + ath79_eth1_data.speed = SPEED_1000; + ath79_eth1_data.duplex = DUPLEX_FULL; + + ath79_register_eth(1); +} + +static void __init ap136_010_setup(void) { - if (dev->bus->number == 1 && (PCI_SLOT(dev->devfn)) == 0) - dev->dev.platform_data = &ap136_ath9k_data; + u8 *art = (u8 *) KSEG1ADDR(0x1fff0000); - return 0; + /* GMAC0 of the AR8327 switch is connected to GMAC0 via RGMII */ + ap136_ar8327_pad0_cfg.mode = AR8327_PAD_MAC_RGMII; + ap136_ar8327_pad0_cfg.txclk_delay_en = true; + ap136_ar8327_pad0_cfg.rxclk_delay_en = true; + ap136_ar8327_pad0_cfg.txclk_delay_sel = AR8327_CLK_DELAY_SEL1; + ap136_ar8327_pad0_cfg.rxclk_delay_sel = AR8327_CLK_DELAY_SEL2; + + /* GMAC6 of the AR8327 switch is connected to GMAC1 via SGMII */ + ap136_ar8327_pad6_cfg.mode = AR8327_PAD_MAC_SGMII; + ap136_ar8327_pad6_cfg.rxclk_delay_en = true; + ap136_ar8327_pad6_cfg.rxclk_delay_sel = AR8327_CLK_DELAY_SEL0; + + ath79_eth0_pll_data.pll_1000 = 0xa6000000; + ath79_eth1_pll_data.pll_1000 = 0x03000101; + + ap136_common_setup(); + ap91_pci_init(art + AP136_PCIE_CALDATA_OFFSET, NULL); } -static void __init ap136_pci_init(u8 *eeprom) +MIPS_MACHINE(ATH79_MACH_AP136_010, "AP136-010", + "Atheros AP136-010 reference board", + ap136_010_setup); + +static void __init ap136_020_common_setup(void) { - memcpy(ap136_ath9k_data.eeprom_data, eeprom, - sizeof(ap136_ath9k_data.eeprom_data)); + /* GMAC0 of the AR8327 switch is connected to GMAC1 via SGMII */ + ap136_ar8327_pad0_cfg.mode = AR8327_PAD_MAC_SGMII; + ap136_ar8327_pad0_cfg.sgmii_delay_en = true; + + /* GMAC6 of the AR8327 switch is connected to GMAC0 via RGMII */ + ap136_ar8327_pad6_cfg.mode = AR8327_PAD_MAC_RGMII; + ap136_ar8327_pad6_cfg.txclk_delay_en = true; + ap136_ar8327_pad6_cfg.rxclk_delay_en = true; + ap136_ar8327_pad6_cfg.txclk_delay_sel = AR8327_CLK_DELAY_SEL1; + ap136_ar8327_pad6_cfg.rxclk_delay_sel = AR8327_CLK_DELAY_SEL2; - ath79_pci_set_plat_dev_init(ap136_pci_plat_dev_init); - ath79_register_pci(); + ath79_eth0_pll_data.pll_1000 = 0x56000000; + ath79_eth1_pll_data.pll_1000 = 0x03000101; + + ap136_common_setup(); } -#else -static inline void ap136_pci_init(void) {} -#endif /* CONFIG_PCI */ -static void __init ap136_setup(void) +static void __init ap136_020_setup(void) { u8 *art = (u8 *) KSEG1ADDR(0x1fff0000); - ath79_register_leds_gpio(-1, ARRAY_SIZE(ap136_leds_gpio), - ap136_leds_gpio); - ath79_register_gpio_keys_polled(-1, AP136_KEYS_POLL_INTERVAL, - ARRAY_SIZE(ap136_gpio_keys), - ap136_gpio_keys); - ath79_register_spi(&ap136_spi_data, ap136_spi_info, - ARRAY_SIZE(ap136_spi_info)); - ath79_register_usb(); - ath79_register_wmac(art + AP136_WMAC_CALDATA_OFFSET); - ap136_pci_init(art + AP136_PCIE_CALDATA_OFFSET); + ap136_020_common_setup(); + ap91_pci_init(art + AP136_PCIE_CALDATA_OFFSET, NULL); } -MIPS_MACHINE(ATH79_MACH_AP136_010, "AP136-010", - "Atheros AP136-010 reference board", - ap136_setup); +MIPS_MACHINE(ATH79_MACH_AP136_020, "AP136-020", + "Atheros AP136-020 reference board", + ap136_020_setup); + +/* + * AP135-020 is similar to AP136-020, any future AP135 specific init + * code can be added here. + */ +static void __init ap135_020_setup(void) +{ + ap136_leds_gpio[0].name = "ap135:green:status"; + ap136_leds_gpio[1].name = "ap135:red:status"; + ap136_leds_gpio[2].name = "ap135:green:wps"; + ap136_leds_gpio[3].name = "ap135:red:wps"; + ap136_leds_gpio[4].name = "ap135:red:wlan-2g"; + ap136_leds_gpio[5].name = "ap135:red:usb"; + + ap136_020_common_setup(); + ath79_register_pci(); +} + +MIPS_MACHINE(ATH79_MACH_AP135_020, "AP135-020", + "Atheros AP135-020 reference board", + ap135_020_setup);