--- zzzz-none-000/linux-3.10.107/arch/mips/cavium-octeon/executive/cvmx-helper-board.c	2017-06-27 09:49:32.000000000 +0000
+++ scorpion-7490-727/linux-3.10.107/arch/mips/cavium-octeon/executive/cvmx-helper-board.c	2021-02-04 17:41:59.000000000 +0000
@@ -181,6 +181,26 @@
 			return ipd_port - 16 + 4;
 		else
 			return -1;
+	case CVMX_BOARD_TYPE_UBNT_E100:
+		if (ipd_port >= 0 && ipd_port <= 2)
+			return 7 - ipd_port;
+		else
+			return -1;
+	case CVMX_BOARD_TYPE_CUST_DSR1000N:
+		/*
+		 * Port 2 connects to Broadcom PHY (B5081). Other ports (0-1)
+		 * connect to a switch (BCM53115).
+		 */
+		if (ipd_port == 2)
+			return 8;
+		else
+			return -1;
+	case CVMX_BOARD_TYPE_KONTRON_S1901:
+		if (ipd_port == CVMX_HELPER_BOARD_MGMT_IPD_PORT)
+			return 1;
+		else
+			return -1;
+
 	}
 
 	/* Some unknown board. Somebody forgot to update this function... */
@@ -269,6 +289,18 @@
 			return result;
 		}
 		break;
+	case CVMX_BOARD_TYPE_CUST_DSR1000N:
+		if (ipd_port == 0 || ipd_port == 1) {
+			/* Ports 0 and 1 connect to a switch (BCM53115). */
+			result.s.link_up = 1;
+			result.s.full_duplex = 1;
+			result.s.speed = 1000;
+			return result;
+		} else {
+			/* Port 2 uses a Broadcom PHY (B5081). */
+			is_broadcom_phy = 1;
+		}
+		break;
 	}
 
 	phy_addr = cvmx_helper_board_get_mii_address(ipd_port);
@@ -706,6 +738,42 @@
 				}
 			}
 		}
+	} else if (cvmx_sysinfo_get()->board_type ==
+			CVMX_BOARD_TYPE_UBNT_E100) {
+		cvmx_write_csr(CVMX_ASXX_RX_CLK_SETX(0, interface), 0);
+		cvmx_write_csr(CVMX_ASXX_TX_CLK_SETX(0, interface), 0x10);
+		cvmx_write_csr(CVMX_ASXX_RX_CLK_SETX(1, interface), 0);
+		cvmx_write_csr(CVMX_ASXX_TX_CLK_SETX(1, interface), 0x10);
+		cvmx_write_csr(CVMX_ASXX_RX_CLK_SETX(2, interface), 0);
+		cvmx_write_csr(CVMX_ASXX_TX_CLK_SETX(2, interface), 0x10);
 	}
 	return 0;
 }
+
+/**
+ * Get the clock type used for the USB block based on board type.
+ * Used by the USB code for auto configuration of clock type.
+ *
+ * Return USB clock type enumeration
+ */
+enum cvmx_helper_board_usb_clock_types __cvmx_helper_board_usb_get_clock_type(void)
+{
+	switch (cvmx_sysinfo_get()->board_type) {
+	case CVMX_BOARD_TYPE_BBGW_REF:
+	case CVMX_BOARD_TYPE_LANAI2_A:
+	case CVMX_BOARD_TYPE_LANAI2_U:
+	case CVMX_BOARD_TYPE_LANAI2_G:
+	case CVMX_BOARD_TYPE_NIC10E_66:
+	case CVMX_BOARD_TYPE_UBNT_E100:
+	case CVMX_BOARD_TYPE_CUST_DSR1000N:
+		return USB_CLOCK_TYPE_CRYSTAL_12;
+	case CVMX_BOARD_TYPE_NIC10E:
+		return USB_CLOCK_TYPE_REF_12;
+	default:
+		break;
+	}
+	/* Most boards except NIC10e use a 12MHz crystal */
+	if (OCTEON_IS_OCTEON2())
+		return USB_CLOCK_TYPE_CRYSTAL_12;
+	return USB_CLOCK_TYPE_REF_48;
+}