--- zzzz-none-000/linux-3.10.107/arch/mips/mti-sead3/sead3-platform.c	2017-06-27 09:49:32.000000000 +0000
+++ scorpion-7490-727/linux-3.10.107/arch/mips/mti-sead3/sead3-platform.c	2021-02-04 17:41:59.000000000 +0000
@@ -5,14 +5,22 @@
  *
  * Copyright (C) 2012 MIPS Technologies, Inc.  All rights reserved.
  */
-#include <linux/module.h>
+#include <linux/dma-mapping.h>
 #include <linux/init.h>
+#include <linux/irq.h>
+#include <linux/irqchip/mips-gic.h>
+#include <linux/leds.h>
+#include <linux/mtd/physmap.h>
+#include <linux/platform_device.h>
 #include <linux/serial_8250.h>
+#include <linux/smsc911x.h>
 
-#define UART(base, int)							\
+#include <asm/mips-boards/sead3int.h>
+
+#define UART(base)							\
 {									\
 	.mapbase	= base,						\
-	.irq		= int,						\
+	.irq		= -1,						\
 	.uartclk	= 14745600,					\
 	.iotype		= UPIO_MEM32,					\
 	.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_IOREMAP, \
@@ -20,8 +28,8 @@
 }
 
 static struct plat_serial8250_port uart8250_data[] = {
-	UART(0x1f000900, MIPS_CPU_IRQ_BASE + 4),   /* ttyS0 = USB   */
-	UART(0x1f000800, MIPS_CPU_IRQ_BASE + 4),   /* ttyS1 = RS232 */
+	UART(0x1f000900),   /* ttyS0 = USB   */
+	UART(0x1f000800),   /* ttyS1 = RS232 */
 	{ },
 };
 
@@ -33,13 +41,183 @@
 	},
 };
 
-static int __init uart8250_init(void)
+static struct smsc911x_platform_config sead3_smsc911x_data = {
+	.irq_polarity	= SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
+	.irq_type	= SMSC911X_IRQ_TYPE_PUSH_PULL,
+	.flags		= SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS,
+	.phy_interface	= PHY_INTERFACE_MODE_MII,
+};
+
+static struct resource sead3_net_resources[] = {
+	{
+		.start			= 0x1f010000,
+		.end			= 0x1f01ffff,
+		.flags			= IORESOURCE_MEM
+	}, {
+		.flags			= IORESOURCE_IRQ
+	}
+};
+
+static struct platform_device sead3_net_device = {
+	.name			= "smsc911x",
+	.id			= 0,
+	.dev			= {
+		.platform_data	= &sead3_smsc911x_data,
+	},
+	.num_resources		= ARRAY_SIZE(sead3_net_resources),
+	.resource		= sead3_net_resources
+};
+
+static struct mtd_partition sead3_mtd_partitions[] = {
+	{
+		.name =		"User FS",
+		.offset =	0x00000000,
+		.size =		0x01fc0000,
+	}, {
+		.name =		"Board Config",
+		.offset =	0x01fc0000,
+		.size =		0x00040000,
+		.mask_flags =	MTD_WRITEABLE
+	},
+};
+
+static struct physmap_flash_data sead3_flash_data = {
+	.width		= 4,
+	.nr_parts	= ARRAY_SIZE(sead3_mtd_partitions),
+	.parts		= sead3_mtd_partitions
+};
+
+static struct resource sead3_flash_resource = {
+	.start		= 0x1c000000,
+	.end		= 0x1dffffff,
+	.flags		= IORESOURCE_MEM
+};
+
+static struct platform_device sead3_flash = {
+	.name		= "physmap-flash",
+	.id		= 0,
+	.dev		= {
+		.platform_data	= &sead3_flash_data,
+	},
+	.num_resources	= 1,
+	.resource	= &sead3_flash_resource,
+};
+
+#define LEDFLAGS(bits, shift)		\
+	((bits << 8) | (shift << 8))
+
+#define LEDBITS(id, shift, bits)	\
+	.name = id #shift,		\
+	.flags = LEDFLAGS(bits, shift)
+
+static struct led_info led_data_info[] = {
+	{ LEDBITS("bit", 0, 1) },
+	{ LEDBITS("bit", 1, 1) },
+	{ LEDBITS("bit", 2, 1) },
+	{ LEDBITS("bit", 3, 1) },
+	{ LEDBITS("bit", 4, 1) },
+	{ LEDBITS("bit", 5, 1) },
+	{ LEDBITS("bit", 6, 1) },
+	{ LEDBITS("bit", 7, 1) },
+	{ LEDBITS("all", 0, 8) },
+};
+
+static struct led_platform_data led_data = {
+	.num_leds	= ARRAY_SIZE(led_data_info),
+	.leds		= led_data_info
+};
+
+static struct resource pled_resources[] = {
+	{
+		.start	= 0x1f000210,
+		.end	= 0x1f000217,
+		.flags	= IORESOURCE_MEM
+	}
+};
+
+static struct platform_device pled_device = {
+	.name			= "sead3::pled",
+	.id			= 0,
+	.dev			= {
+		.platform_data	= &led_data,
+	},
+	.num_resources		= ARRAY_SIZE(pled_resources),
+	.resource		= pled_resources
+};
+
+
+static struct resource fled_resources[] = {
+	{
+		.start			= 0x1f000218,
+		.end			= 0x1f00021f,
+		.flags			= IORESOURCE_MEM
+	}
+};
+
+static struct platform_device fled_device = {
+	.name			= "sead3::fled",
+	.id			= 0,
+	.dev			= {
+		.platform_data	= &led_data,
+	},
+	.num_resources		= ARRAY_SIZE(fled_resources),
+	.resource		= fled_resources
+};
+
+static struct platform_device sead3_led_device = {
+        .name   = "sead3-led",
+        .id     = -1,
+};
+
+static struct resource ehci_resources[] = {
+	{
+		.start			= 0x1b200000,
+		.end			= 0x1b200fff,
+		.flags			= IORESOURCE_MEM
+	}, {
+		.flags			= IORESOURCE_IRQ
+	}
+};
+
+static u64 sead3_usbdev_dma_mask = DMA_BIT_MASK(32);
+
+static struct platform_device ehci_device = {
+	.name		= "sead3-ehci",
+	.id		= 0,
+	.dev		= {
+		.dma_mask		= &sead3_usbdev_dma_mask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32)
+	},
+	.num_resources	= ARRAY_SIZE(ehci_resources),
+	.resource	= ehci_resources
+};
+
+static struct platform_device *sead3_platform_devices[] __initdata = {
+	&uart8250_device,
+	&sead3_flash,
+	&pled_device,
+	&fled_device,
+	&sead3_led_device,
+	&ehci_device,
+	&sead3_net_device,
+};
+
+static int __init sead3_platforms_device_init(void)
 {
-	return platform_device_register(&uart8250_device);
-}
+	if (gic_present) {
+		uart8250_data[0].irq = MIPS_GIC_IRQ_BASE + GIC_INT_UART0;
+		uart8250_data[1].irq = MIPS_GIC_IRQ_BASE + GIC_INT_UART1;
+		ehci_resources[1].start = MIPS_GIC_IRQ_BASE + GIC_INT_EHCI;
+		sead3_net_resources[1].start = MIPS_GIC_IRQ_BASE + GIC_INT_NET;
+	} else {
+		uart8250_data[0].irq = MIPS_CPU_IRQ_BASE + CPU_INT_UART0;
+		uart8250_data[1].irq = MIPS_CPU_IRQ_BASE + CPU_INT_UART1;
+		ehci_resources[1].start = MIPS_CPU_IRQ_BASE + CPU_INT_EHCI;
+		sead3_net_resources[1].start = MIPS_CPU_IRQ_BASE + CPU_INT_NET;
+	}
 
-module_init(uart8250_init);
+	return platform_add_devices(sead3_platform_devices,
+				    ARRAY_SIZE(sead3_platform_devices));
+}
 
-MODULE_AUTHOR("Chris Dearman <chris@mips.com>");
-MODULE_LICENSE("GPL");
-MODULE_DESCRIPTION("8250 UART probe driver for SEAD3");
+device_initcall(sead3_platforms_device_init);