--- zzzz-none-000/linux-3.10.107/arch/x86/include/asm/mwait.h	2017-06-27 09:49:32.000000000 +0000
+++ scorpion-7490-727/linux-3.10.107/arch/x86/include/asm/mwait.h	2021-02-04 17:41:59.000000000 +0000
@@ -1,6 +1,8 @@
 #ifndef _ASM_X86_MWAIT_H
 #define _ASM_X86_MWAIT_H
 
+#include <linux/sched.h>
+
 #define MWAIT_SUBSTATE_MASK		0xf
 #define MWAIT_CSTATE_MASK		0xf
 #define MWAIT_SUBSTATE_SIZE		4
@@ -12,5 +14,99 @@
 #define CPUID5_ECX_INTERRUPT_BREAK	0x2
 
 #define MWAIT_ECX_INTERRUPT_BREAK	0x1
+#define MWAITX_ECX_TIMER_ENABLE		BIT(1)
+#define MWAITX_MAX_LOOPS		((u32)-1)
+#define MWAITX_DISABLE_CSTATES		0xf
+
+static inline void __monitor(const void *eax, unsigned long ecx,
+			     unsigned long edx)
+{
+	/* "monitor %eax, %ecx, %edx;" */
+	asm volatile(".byte 0x0f, 0x01, 0xc8;"
+		     :: "a" (eax), "c" (ecx), "d"(edx));
+}
+
+static inline void __monitorx(const void *eax, unsigned long ecx,
+			      unsigned long edx)
+{
+	/* "monitorx %eax, %ecx, %edx;" */
+	asm volatile(".byte 0x0f, 0x01, 0xfa;"
+		     :: "a" (eax), "c" (ecx), "d"(edx));
+}
+
+static inline void __mwait(unsigned long eax, unsigned long ecx)
+{
+	/* "mwait %eax, %ecx;" */
+	asm volatile(".byte 0x0f, 0x01, 0xc9;"
+		     :: "a" (eax), "c" (ecx));
+}
+
+/*
+ * MWAITX allows for a timer expiration to get the core out a wait state in
+ * addition to the default MWAIT exit condition of a store appearing at a
+ * monitored virtual address.
+ *
+ * Registers:
+ *
+ * MWAITX ECX[1]: enable timer if set
+ * MWAITX EBX[31:0]: max wait time expressed in SW P0 clocks. The software P0
+ * frequency is the same as the TSC frequency.
+ *
+ * Below is a comparison between MWAIT and MWAITX on AMD processors:
+ *
+ *                 MWAIT                           MWAITX
+ * opcode          0f 01 c9           |            0f 01 fb
+ * ECX[0]                  value of RFLAGS.IF seen by instruction
+ * ECX[1]          unused/#GP if set  |            enable timer if set
+ * ECX[31:2]                     unused/#GP if set
+ * EAX                           unused (reserve for hint)
+ * EBX[31:0]       unused             |            max wait time (P0 clocks)
+ *
+ *                 MONITOR                         MONITORX
+ * opcode          0f 01 c8           |            0f 01 fa
+ * EAX                     (logical) address to monitor
+ * ECX                     #GP if not zero
+ */
+static inline void __mwaitx(unsigned long eax, unsigned long ebx,
+			    unsigned long ecx)
+{
+	/* "mwaitx %eax, %ebx, %ecx;" */
+	asm volatile(".byte 0x0f, 0x01, 0xfb;"
+		     :: "a" (eax), "b" (ebx), "c" (ecx));
+}
+
+static inline void __sti_mwait(unsigned long eax, unsigned long ecx)
+{
+	trace_hardirqs_on();
+	/* "mwait %eax, %ecx;" */
+	asm volatile("sti; .byte 0x0f, 0x01, 0xc9;"
+		     :: "a" (eax), "c" (ecx));
+}
+
+/*
+ * This uses new MONITOR/MWAIT instructions on P4 processors with PNI,
+ * which can obviate IPI to trigger checking of need_resched.
+ * We execute MONITOR against need_resched and enter optimized wait state
+ * through MWAIT. Whenever someone changes need_resched, we would be woken
+ * up from MWAIT (without an IPI).
+ *
+ * New with Core Duo processors, MWAIT can take some hints based on CPU
+ * capability.
+ */
+static inline void mwait_idle_with_hints(unsigned long eax, unsigned long ecx)
+{
+	if (!current_set_polling_and_test()) {
+		if (static_cpu_has_bug(X86_BUG_CLFLUSH_MONITOR)) {
+			mb();
+			clflush((void *)&current_thread_info()->flags);
+			mb();
+		}
+
+		__monitor((void *)&current_thread_info()->flags, 0, 0);
+		if (!need_resched())
+			__mwait(eax, ecx);
+	}
+	current_clr_polling();
+}
 
 #endif /* _ASM_X86_MWAIT_H */