--- zzzz-none-000/linux-3.10.107/drivers/gpu/drm/radeon/atombios.h 2017-06-27 09:49:32.000000000 +0000 +++ scorpion-7490-727/linux-3.10.107/drivers/gpu/drm/radeon/atombios.h 2021-02-04 17:41:59.000000000 +0000 @@ -74,6 +74,8 @@ #define ATOM_PPLL2 1 #define ATOM_DCPLL 2 #define ATOM_PPLL0 2 +#define ATOM_PPLL3 3 + #define ATOM_EXT_PLL1 8 #define ATOM_EXT_PLL2 9 #define ATOM_EXT_CLOCK 10 @@ -259,7 +261,7 @@ USHORT AdjustDisplayPll; //Atomic Table, used by various SW componentes. USHORT AdjustMemoryController; //Atomic Table, indirectly used by various SW components,called from SetMemoryClock USHORT EnableASIC_StaticPwrMgt; //Atomic Table, only used by Bios - USHORT ASIC_StaticPwrMgtStatusChange; //Obsolete , only used by Bios + USHORT SetUniphyInstance; //Atomic Table, only used by Bios USHORT DAC_LoadDetection; //Atomic Table, directly used by various SW components,latest version 1.2 USHORT LVTMAEncoderControl; //Atomic Table,directly used by various SW components,latest version 1.3 USHORT HW_Misc_Operation; //Atomic Table, directly used by various SW components,latest version 1.1 @@ -271,7 +273,7 @@ USHORT TVEncoderControl; //Function Table,directly used by various SW components,latest version 1.1 USHORT PatchMCSetting; //only used by BIOS USHORT MC_SEQ_Control; //only used by BIOS - USHORT TV1OutputControl; //Atomic Table, Obsolete from Ry6xx, use DAC2 Output instead + USHORT Gfx_Harvesting; //Atomic Table, Obsolete from Ry6xx, Now only used by BIOS for GFX harvesting USHORT EnableScaler; //Atomic Table, used only by Bios USHORT BlankCRTC; //Atomic Table, directly used by various SW components,latest version 1.1 USHORT EnableCRTC; //Atomic Table, directly used by various SW components,latest version 1.1 @@ -328,7 +330,7 @@ #define UNIPHYTransmitterControl DIG1TransmitterControl #define LVTMATransmitterControl DIG2TransmitterControl #define SetCRTC_DPM_State GetConditionalGoldenSetting -#define SetUniphyInstance ASIC_StaticPwrMgtStatusChange +#define ASIC_StaticPwrMgtStatusChange SetUniphyInstance #define HPDInterruptService ReadHWAssistedI2CStatus #define EnableVGA_Access GetSCLKOverMCLKRatio #define EnableYUV GetDispObjectInfo @@ -338,7 +340,7 @@ #define TMDSAEncoderControl PatchMCSetting #define LVDSEncoderControl MC_SEQ_Control #define LCD1OutputControl HW_Misc_Operation - +#define TV1OutputControl Gfx_Harvesting typedef struct _ATOM_MASTER_COMMAND_TABLE { @@ -478,11 +480,11 @@ typedef struct _COMPUTE_MEMORY_ENGINE_PLL_PARAMETERS_V4 { #if ATOM_BIG_ENDIAN - ULONG ucPostDiv; //return parameter: post divider which is used to program to register directly + ULONG ucPostDiv:8; //return parameter: post divider which is used to program to register directly ULONG ulClock:24; //Input= target clock, output = actual clock #else ULONG ulClock:24; //Input= target clock, output = actual clock - ULONG ucPostDiv; //return parameter: post divider which is used to program to register directly + ULONG ucPostDiv:8; //return parameter: post divider which is used to program to register directly #endif }COMPUTE_MEMORY_ENGINE_PLL_PARAMETERS_V4; @@ -504,6 +506,32 @@ UCHAR ucReserved; }COMPUTE_MEMORY_ENGINE_PLL_PARAMETERS_V5; + +typedef struct _COMPUTE_GPU_CLOCK_INPUT_PARAMETERS_V1_6 +{ + ATOM_COMPUTE_CLOCK_FREQ ulClock; //Input Parameter + ULONG ulReserved[2]; +}COMPUTE_GPU_CLOCK_INPUT_PARAMETERS_V1_6; + +//ATOM_COMPUTE_CLOCK_FREQ.ulComputeClockFlag +#define COMPUTE_GPUCLK_INPUT_FLAG_CLK_TYPE_MASK 0x0f +#define COMPUTE_GPUCLK_INPUT_FLAG_DEFAULT_GPUCLK 0x00 +#define COMPUTE_GPUCLK_INPUT_FLAG_SCLK 0x01 + +typedef struct _COMPUTE_GPU_CLOCK_OUTPUT_PARAMETERS_V1_6 +{ + COMPUTE_MEMORY_ENGINE_PLL_PARAMETERS_V4 ulClock; //Output Parameter: ucPostDiv=DFS divider + ATOM_S_MPLL_FB_DIVIDER ulFbDiv; //Output Parameter: PLL FB divider + UCHAR ucPllRefDiv; //Output Parameter: PLL ref divider + UCHAR ucPllPostDiv; //Output Parameter: PLL post divider + UCHAR ucPllCntlFlag; //Output Flags: control flag + UCHAR ucReserved; +}COMPUTE_GPU_CLOCK_OUTPUT_PARAMETERS_V1_6; + +//ucPllCntlFlag +#define SPLL_CNTL_FLAG_VCO_MODE_MASK 0x03 + + // ucInputFlag #define ATOM_PLL_INPUT_FLAG_PLL_STROBE_MODE_EN 1 // 1-StrobeMode, 0-PerformanceMode @@ -1683,9 +1711,12 @@ #define PIXEL_CLOCK_V6_MISC_HDMI_BPP_MASK 0x0c #define PIXEL_CLOCK_V6_MISC_HDMI_24BPP 0x00 #define PIXEL_CLOCK_V6_MISC_HDMI_36BPP 0x04 +#define PIXEL_CLOCK_V6_MISC_HDMI_36BPP_V6 0x08 //for V6, the correct defintion for 36bpp should be 2 for 36bpp(2:1) #define PIXEL_CLOCK_V6_MISC_HDMI_30BPP 0x08 +#define PIXEL_CLOCK_V6_MISC_HDMI_30BPP_V6 0x04 //for V6, the correct defintion for 30bpp should be 1 for 36bpp(5:4) #define PIXEL_CLOCK_V6_MISC_HDMI_48BPP 0x0c #define PIXEL_CLOCK_V6_MISC_REF_DIV_SRC 0x10 +#define PIXEL_CLOCK_V6_MISC_GEN_DPREFCLK 0x40 typedef struct _GET_DISP_PLL_STATUS_INPUT_PARAMETERS_V2 { @@ -2102,6 +2133,17 @@ }DVO_ENCODER_CONTROL_PARAMETERS_V3; #define DVO_ENCODER_CONTROL_PS_ALLOCATION_V3 DVO_ENCODER_CONTROL_PARAMETERS_V3 +typedef struct _DVO_ENCODER_CONTROL_PARAMETERS_V1_4 +{ + USHORT usPixelClock; + UCHAR ucDVOConfig; + UCHAR ucAction; //ATOM_ENABLE/ATOM_DISABLE/ATOM_HPD_INIT + UCHAR ucBitPerColor; //please refer to definition of PANEL_xBIT_PER_COLOR + UCHAR ucReseved[3]; +}DVO_ENCODER_CONTROL_PARAMETERS_V1_4; +#define DVO_ENCODER_CONTROL_PS_ALLOCATION_V1_4 DVO_ENCODER_CONTROL_PARAMETERS_V1_4 + + //ucTableFormatRevision=1 //ucTableContentRevision=3 structure is not changed but usMisc add bit 1 as another input for // bit1=0: non-coherent mode @@ -2165,7 +2207,7 @@ #define SET_ASIC_VOLTAGE_MODE_SOURCE_B 0x4 #define SET_ASIC_VOLTAGE_MODE_SET_VOLTAGE 0x0 -#define SET_ASIC_VOLTAGE_MODE_GET_GPIOVAL 0x1 +#define SET_ASIC_VOLTAGE_MODE_GET_GPIOVAL 0x1 #define SET_ASIC_VOLTAGE_MODE_GET_GPIOMASK 0x2 typedef struct _SET_VOLTAGE_PARAMETERS @@ -2183,7 +2225,7 @@ USHORT usVoltageLevel; // real voltage level }SET_VOLTAGE_PARAMETERS_V2; - +// used by both SetVoltageTable v1.3 and v1.4 typedef struct _SET_VOLTAGE_PARAMETERS_V1_3 { UCHAR ucVoltageType; // To tell which voltage to set up, VDDC/MVDDC/MVDDQ/VDDCI @@ -2200,15 +2242,20 @@ //SET_VOLTAGE_PARAMETERS_V3.ucVoltageMode #define ATOM_SET_VOLTAGE 0 //Set voltage Level #define ATOM_INIT_VOLTAGE_REGULATOR 3 //Init Regulator -#define ATOM_SET_VOLTAGE_PHASE 4 //Set Vregulator Phase -#define ATOM_GET_MAX_VOLTAGE 6 //Get Max Voltage, not used in SetVoltageTable v1.3 -#define ATOM_GET_VOLTAGE_LEVEL 6 //Get Voltage level from vitual voltage ID +#define ATOM_SET_VOLTAGE_PHASE 4 //Set Vregulator Phase, only for SVID/PVID regulator +#define ATOM_GET_MAX_VOLTAGE 6 //Get Max Voltage, not used from SetVoltageTable v1.3 +#define ATOM_GET_VOLTAGE_LEVEL 6 //Get Voltage level from vitual voltage ID, not used for SetVoltage v1.4 +#define ATOM_GET_LEAKAGE_ID 8 //Get Leakage Voltage Id ( starting from SMU7x IP ), SetVoltage v1.4 // define vitual voltage id in usVoltageLevel #define ATOM_VIRTUAL_VOLTAGE_ID0 0xff01 #define ATOM_VIRTUAL_VOLTAGE_ID1 0xff02 #define ATOM_VIRTUAL_VOLTAGE_ID2 0xff03 #define ATOM_VIRTUAL_VOLTAGE_ID3 0xff04 +#define ATOM_VIRTUAL_VOLTAGE_ID4 0xff05 +#define ATOM_VIRTUAL_VOLTAGE_ID5 0xff06 +#define ATOM_VIRTUAL_VOLTAGE_ID6 0xff07 +#define ATOM_VIRTUAL_VOLTAGE_ID7 0xff08 typedef struct _SET_VOLTAGE_PS_ALLOCATION { @@ -2245,15 +2292,36 @@ #define ATOM_GET_VOLTAGE_VID 0x00 #define ATOM_GET_VOTLAGE_INIT_SEQ 0x03 #define ATOM_GET_VOLTTAGE_PHASE_PHASE_VID 0x04 -// for SI, this state map to 0xff02 voltage state in Power Play table, which is power boost state -#define ATOM_GET_VOLTAGE_STATE0_LEAKAGE_VID 0x10 +#define ATOM_GET_VOLTAGE_SVID2 0x07 //Get SVI2 Regulator Info +// for SI, this state map to 0xff02 voltage state in Power Play table, which is power boost state +#define ATOM_GET_VOLTAGE_STATE0_LEAKAGE_VID 0x10 // for SI, this state map to 0xff01 voltage state in Power Play table, which is performance state #define ATOM_GET_VOLTAGE_STATE1_LEAKAGE_VID 0x11 -// undefined power state + #define ATOM_GET_VOLTAGE_STATE2_LEAKAGE_VID 0x12 #define ATOM_GET_VOLTAGE_STATE3_LEAKAGE_VID 0x13 +// New Added from CI Hawaii for GetVoltageInfoTable, input parameter structure +typedef struct _GET_VOLTAGE_INFO_INPUT_PARAMETER_V1_2 +{ + UCHAR ucVoltageType; // Input: To tell which voltage to set up, VDDC/MVDDC/MVDDQ/VDDCI + UCHAR ucVoltageMode; // Input: Indicate action: Get voltage info + USHORT usVoltageLevel; // Input: real voltage level in unit of mv or Voltage Phase (0, 1, 2, .. ) or Leakage Id + ULONG ulSCLKFreq; // Input: when ucVoltageMode= ATOM_GET_VOLTAGE_EVV_VOLTAGE, DPM state SCLK frequency, Define in PPTable SCLK/Voltage dependence table +}GET_VOLTAGE_INFO_INPUT_PARAMETER_V1_2; + +// New in GetVoltageInfo v1.2 ucVoltageMode +#define ATOM_GET_VOLTAGE_EVV_VOLTAGE 0x09 + +// New Added from CI Hawaii for EVV feature +typedef struct _GET_EVV_VOLTAGE_INFO_OUTPUT_PARAMETER_V1_2 +{ + USHORT usVoltageLevel; // real voltage level in unit of mv + USHORT usVoltageId; // Voltage Id programmed in Voltage Regulator + ULONG ulReseved; +}GET_EVV_VOLTAGE_INFO_OUTPUT_PARAMETER_V1_2; + /****************************************************************************/ // Structures used by TVEncoderControlTable /****************************************************************************/ @@ -2628,7 +2696,8 @@ ULONG ulFirmwareRevision; ULONG ulDefaultEngineClock; //In 10Khz unit ULONG ulDefaultMemoryClock; //In 10Khz unit - ULONG ulReserved[2]; + ULONG ulSPLL_OutputFreq; //In 10Khz unit + ULONG ulGPUPLL_OutputFreq; //In 10Khz unit ULONG ulReserved1; //Was ulMaxEngineClockPLL_Output; //In 10Khz unit* ULONG ulReserved2; //Was ulMaxMemoryClockPLL_Output; //In 10Khz unit* ULONG ulMaxPixelClockPLL_Output; //In 10Khz unit @@ -3813,6 +3882,14 @@ UCHAR ucGPIO_ID; }ATOM_GPIO_PIN_ASSIGNMENT; +//ucGPIO_ID pre-define id for multiple usage +//from SMU7.x, if ucGPIO_ID=PP_AC_DC_SWITCH_GPIO_PINID in GPIO_LUTTable, AC/DC swithing feature is enable +#define PP_AC_DC_SWITCH_GPIO_PINID 60 +//from SMU7.x, if ucGPIO_ID=VDDC_REGULATOR_VRHOT_GPIO_PINID in GPIO_LUTable, VRHot feature is enable +#define VDDC_VRHOT_GPIO_PINID 61 +//if ucGPIO_ID=VDDC_PCC_GPIO_PINID in GPIO_LUTable, Peak Current Control feature is enabled +#define VDDC_PCC_GPIO_PINID 62 + typedef struct _ATOM_GPIO_PIN_LUT { ATOM_COMMON_TABLE_HEADER sHeader; @@ -4074,17 +4151,19 @@ //usCaps #define EXT_DISPLAY_PATH_CAPS__HBR2_DISABLE 0x01 +#define EXT_DISPLAY_PATH_CAPS__DP_FIXED_VS_EN 0x02 typedef struct _ATOM_EXTERNAL_DISPLAY_CONNECTION_INFO { ATOM_COMMON_TABLE_HEADER sHeader; UCHAR ucGuid [NUMBER_OF_UCHAR_FOR_GUID]; // a GUID is a 16 byte long string EXT_DISPLAY_PATH sPath[MAX_NUMBER_OF_EXT_DISPLAY_PATH]; // total of fixed 7 entries. - UCHAR ucChecksum; // a simple Checksum of the sum of whole structure equal to 0x0. + UCHAR ucChecksum; // a simple Checksum of the sum of whole structure equal to 0x0. UCHAR uc3DStereoPinId; // use for eDP panel UCHAR ucRemoteDisplayConfig; UCHAR uceDPToLVDSRxId; - UCHAR Reserved[4]; // for potential expansion + UCHAR ucFixDPVoltageSwing; // usCaps[1]=1, this indicate DP_LANE_SET value + UCHAR Reserved[3]; // for potential expansion }ATOM_EXTERNAL_DISPLAY_CONNECTION_INFO; //Related definitions, all records are different but they have a commond header @@ -4115,10 +4194,10 @@ #define ATOM_OBJECT_LINK_RECORD_TYPE 18 //Once this record is present under one object, it indicats the oobject is linked to another obj described by the record #define ATOM_CONNECTOR_REMOTE_CAP_RECORD_TYPE 19 #define ATOM_ENCODER_CAP_RECORD_TYPE 20 - +#define ATOM_BRACKET_LAYOUT_RECORD_TYPE 21 //Must be updated when new record type is added,equal to that record definition! -#define ATOM_MAX_OBJECT_RECORD_NUMBER ATOM_ENCODER_CAP_RECORD_TYPE +#define ATOM_MAX_OBJECT_RECORD_NUMBER ATOM_BRACKET_LAYOUT_RECORD_TYPE typedef struct _ATOM_I2C_RECORD { @@ -4343,6 +4422,31 @@ USHORT usReserved; }ATOM_CONNECTOR_REMOTE_CAP_RECORD; +typedef struct _ATOM_CONNECTOR_LAYOUT_INFO +{ + USHORT usConnectorObjectId; + UCHAR ucConnectorType; + UCHAR ucPosition; +}ATOM_CONNECTOR_LAYOUT_INFO; + +// define ATOM_CONNECTOR_LAYOUT_INFO.ucConnectorType to describe the display connector size +#define CONNECTOR_TYPE_DVI_D 1 +#define CONNECTOR_TYPE_DVI_I 2 +#define CONNECTOR_TYPE_VGA 3 +#define CONNECTOR_TYPE_HDMI 4 +#define CONNECTOR_TYPE_DISPLAY_PORT 5 +#define CONNECTOR_TYPE_MINI_DISPLAY_PORT 6 + +typedef struct _ATOM_BRACKET_LAYOUT_RECORD +{ + ATOM_COMMON_RECORD_HEADER sheader; + UCHAR ucLength; + UCHAR ucWidth; + UCHAR ucConnNum; + UCHAR ucReserved; + ATOM_CONNECTOR_LAYOUT_INFO asConnInfo[1]; +}ATOM_BRACKET_LAYOUT_RECORD; + /****************************************************************************/ // ASIC voltage data table /****************************************************************************/ @@ -4416,6 +4520,13 @@ #define VOLTAGE_CONTROL_ID_CHL822x 0x08 #define VOLTAGE_CONTROL_ID_VT1586M 0x09 #define VOLTAGE_CONTROL_ID_UP1637 0x0A +#define VOLTAGE_CONTROL_ID_CHL8214 0x0B +#define VOLTAGE_CONTROL_ID_UP1801 0x0C +#define VOLTAGE_CONTROL_ID_ST6788A 0x0D +#define VOLTAGE_CONTROL_ID_CHLIR3564SVI2 0x0E +#define VOLTAGE_CONTROL_ID_AD527x 0x0F +#define VOLTAGE_CONTROL_ID_NCP81022 0x10 +#define VOLTAGE_CONTROL_ID_LTC2635 0x11 typedef struct _ATOM_VOLTAGE_OBJECT { @@ -4458,6 +4569,16 @@ USHORT usSize; //Size of Object }ATOM_VOLTAGE_OBJECT_HEADER_V3; +// ATOM_VOLTAGE_OBJECT_HEADER_V3.ucVoltageMode +#define VOLTAGE_OBJ_GPIO_LUT 0 //VOLTAGE and GPIO Lookup table ->ATOM_GPIO_VOLTAGE_OBJECT_V3 +#define VOLTAGE_OBJ_VR_I2C_INIT_SEQ 3 //VOLTAGE REGULATOR INIT sequece through I2C -> ATOM_I2C_VOLTAGE_OBJECT_V3 +#define VOLTAGE_OBJ_PHASE_LUT 4 //Set Vregulator Phase lookup table ->ATOM_GPIO_VOLTAGE_OBJECT_V3 +#define VOLTAGE_OBJ_SVID2 7 //Indicate voltage control by SVID2 ->ATOM_SVID2_VOLTAGE_OBJECT_V3 +#define VOLTAGE_OBJ_EVV 8 +#define VOLTAGE_OBJ_PWRBOOST_LEAKAGE_LUT 0x10 //Powerboost Voltage and LeakageId lookup table->ATOM_LEAKAGE_VOLTAGE_OBJECT_V3 +#define VOLTAGE_OBJ_HIGH_STATE_LEAKAGE_LUT 0x11 //High voltage state Voltage and LeakageId lookup table->ATOM_LEAKAGE_VOLTAGE_OBJECT_V3 +#define VOLTAGE_OBJ_HIGH1_STATE_LEAKAGE_LUT 0x12 //High1 voltage state Voltage and LeakageId lookup table->ATOM_LEAKAGE_VOLTAGE_OBJECT_V3 + typedef struct _VOLTAGE_LUT_ENTRY_V2 { ULONG ulVoltageId; // The Voltage ID which is used to program GPIO register @@ -4473,7 +4594,7 @@ typedef struct _ATOM_I2C_VOLTAGE_OBJECT_V3 { - ATOM_VOLTAGE_OBJECT_HEADER_V3 sHeader; + ATOM_VOLTAGE_OBJECT_HEADER_V3 sHeader; // voltage mode = VOLTAGE_OBJ_VR_I2C_INIT_SEQ UCHAR ucVoltageRegulatorId; //Indicate Voltage Regulator Id UCHAR ucVoltageControlI2cLine; UCHAR ucVoltageControlAddress; @@ -4482,9 +4603,13 @@ VOLTAGE_LUT_ENTRY asVolI2cLut[1]; // end with 0xff }ATOM_I2C_VOLTAGE_OBJECT_V3; +// ATOM_I2C_VOLTAGE_OBJECT_V3.ucVoltageControlFlag +#define VOLTAGE_DATA_ONE_BYTE 0 +#define VOLTAGE_DATA_TWO_BYTE 1 + typedef struct _ATOM_GPIO_VOLTAGE_OBJECT_V3 { - ATOM_VOLTAGE_OBJECT_HEADER_V3 sHeader; + ATOM_VOLTAGE_OBJECT_HEADER_V3 sHeader; // voltage mode = VOLTAGE_OBJ_GPIO_LUT or VOLTAGE_OBJ_PHASE_LUT UCHAR ucVoltageGpioCntlId; // default is 0 which indicate control through CG VID mode UCHAR ucGpioEntryNum; // indiate the entry numbers of Votlage/Gpio value Look up table UCHAR ucPhaseDelay; // phase delay in unit of micro second @@ -4495,7 +4620,7 @@ typedef struct _ATOM_LEAKAGE_VOLTAGE_OBJECT_V3 { - ATOM_VOLTAGE_OBJECT_HEADER_V3 sHeader; + ATOM_VOLTAGE_OBJECT_HEADER_V3 sHeader; // voltage mode = 0x10/0x11/0x12 UCHAR ucLeakageCntlId; // default is 0 UCHAR ucLeakageEntryNum; // indicate the entry number of LeakageId/Voltage Lut table UCHAR ucReserved[2]; @@ -4503,10 +4628,27 @@ LEAKAGE_VOLTAGE_LUT_ENTRY_V2 asLeakageIdLut[1]; }ATOM_LEAKAGE_VOLTAGE_OBJECT_V3; + +typedef struct _ATOM_SVID2_VOLTAGE_OBJECT_V3 +{ + ATOM_VOLTAGE_OBJECT_HEADER_V3 sHeader; // voltage mode = VOLTAGE_OBJ_SVID2 +// 14:7 – PSI0_VID +// 6 – PSI0_EN +// 5 – PSI1 +// 4:2 – load line slope trim. +// 1:0 – offset trim, + USHORT usLoadLine_PSI; +// GPU GPIO pin Id to SVID2 regulator VRHot pin. possible value 0~31. 0 means GPIO0, 31 means GPIO31 + UCHAR ucSVDGpioId; //0~31 indicate GPIO0~31 + UCHAR ucSVCGpioId; //0~31 indicate GPIO0~31 + ULONG ulReserved; +}ATOM_SVID2_VOLTAGE_OBJECT_V3; + typedef union _ATOM_VOLTAGE_OBJECT_V3{ ATOM_GPIO_VOLTAGE_OBJECT_V3 asGpioVoltageObj; ATOM_I2C_VOLTAGE_OBJECT_V3 asI2cVoltageObj; ATOM_LEAKAGE_VOLTAGE_OBJECT_V3 asLeakageObj; + ATOM_SVID2_VOLTAGE_OBJECT_V3 asSVID2Obj; }ATOM_VOLTAGE_OBJECT_V3; typedef struct _ATOM_VOLTAGE_OBJECT_INFO_V3_1 @@ -4536,6 +4678,64 @@ ATOM_ASIC_PROFILE_VOLTAGE asVoltage; }ATOM_ASIC_PROFILING_INFO; +typedef struct _ATOM_ASIC_PROFILING_INFO_V2_1 +{ + ATOM_COMMON_TABLE_HEADER asHeader; + UCHAR ucLeakageBinNum; // indicate the entry number of LeakageId/Voltage Lut table + USHORT usLeakageBinArrayOffset; // offset of USHORT Leakage Bin list array ( from lower LeakageId to higher) + + UCHAR ucElbVDDC_Num; + USHORT usElbVDDC_IdArrayOffset; // offset of USHORT virtual VDDC voltage id ( 0xff01~0xff08 ) + USHORT usElbVDDC_LevelArrayOffset; // offset of 2 dimension voltage level USHORT array + + UCHAR ucElbVDDCI_Num; + USHORT usElbVDDCI_IdArrayOffset; // offset of USHORT virtual VDDCI voltage id ( 0xff01~0xff08 ) + USHORT usElbVDDCI_LevelArrayOffset; // offset of 2 dimension voltage level USHORT array +}ATOM_ASIC_PROFILING_INFO_V2_1; + +typedef struct _ATOM_ASIC_PROFILING_INFO_V3_1 +{ + ATOM_COMMON_TABLE_HEADER asHeader; + ULONG ulEvvDerateTdp; + ULONG ulEvvDerateTdc; + ULONG ulBoardCoreTemp; + ULONG ulMaxVddc; + ULONG ulMinVddc; + ULONG ulLoadLineSlop; + ULONG ulLeakageTemp; + ULONG ulLeakageVoltage; + ULONG ulCACmEncodeRange; + ULONG ulCACmEncodeAverage; + ULONG ulCACbEncodeRange; + ULONG ulCACbEncodeAverage; + ULONG ulKt_bEncodeRange; + ULONG ulKt_bEncodeAverage; + ULONG ulKv_mEncodeRange; + ULONG ulKv_mEncodeAverage; + ULONG ulKv_bEncodeRange; + ULONG ulKv_bEncodeAverage; + ULONG ulLkgEncodeLn_MaxDivMin; + ULONG ulLkgEncodeMin; + ULONG ulEfuseLogisticAlpha; + USHORT usPowerDpm0; + USHORT usCurrentDpm0; + USHORT usPowerDpm1; + USHORT usCurrentDpm1; + USHORT usPowerDpm2; + USHORT usCurrentDpm2; + USHORT usPowerDpm3; + USHORT usCurrentDpm3; + USHORT usPowerDpm4; + USHORT usCurrentDpm4; + USHORT usPowerDpm5; + USHORT usCurrentDpm5; + USHORT usPowerDpm6; + USHORT usCurrentDpm6; + USHORT usPowerDpm7; + USHORT usCurrentDpm7; +}ATOM_ASIC_PROFILING_INFO_V3_1; + + typedef struct _ATOM_POWER_SOURCE_OBJECT { UCHAR ucPwrSrcId; // Power source @@ -4652,6 +4852,8 @@ #define SYS_INFO_LVDSMISC__888_BPC 0x04 #define SYS_INFO_LVDSMISC__OVERRIDE_EN 0x08 #define SYS_INFO_LVDSMISC__BLON_ACTIVE_LOW 0x10 +// new since Trinity +#define SYS_INFO_LVDSMISC__TRAVIS_LVDS_VOL_OVERRIDE_EN 0x20 // not used any more #define SYS_INFO_LVDSMISC__VSYNC_ACTIVE_LOW 0x04 @@ -4752,6 +4954,29 @@ ATOM_INTEGRATED_SYSTEM_INFO_V6 sIntegratedSysInfo; ULONG ulPowerplayTable[128]; }ATOM_FUSION_SYSTEM_INFO_V1; + + +typedef struct _ATOM_TDP_CONFIG_BITS +{ +#if ATOM_BIG_ENDIAN + ULONG uReserved:2; + ULONG uTDP_Value:14; // Original TDP value in tens of milli watts + ULONG uCTDP_Value:14; // Override value in tens of milli watts + ULONG uCTDP_Enable:2; // = (uCTDP_Value > uTDP_Value? 2: (uCTDP_Value < uTDP_Value)) +#else + ULONG uCTDP_Enable:2; // = (uCTDP_Value > uTDP_Value? 2: (uCTDP_Value < uTDP_Value)) + ULONG uCTDP_Value:14; // Override value in tens of milli watts + ULONG uTDP_Value:14; // Original TDP value in tens of milli watts + ULONG uReserved:2; +#endif +}ATOM_TDP_CONFIG_BITS; + +typedef union _ATOM_TDP_CONFIG +{ + ATOM_TDP_CONFIG_BITS TDP_config; + ULONG TDP_config_all; +}ATOM_TDP_CONFIG; + /********************************************************************************************************************** ATOM_FUSION_SYSTEM_INFO_V1 Description sIntegratedSysInfo: refer to ATOM_INTEGRATED_SYSTEM_INFO_V6 definition. @@ -4784,7 +5009,8 @@ UCHAR ucMemoryType; UCHAR ucUMAChannelNumber; UCHAR strVBIOSMsg[40]; - ULONG ulReserved[20]; + ATOM_TDP_CONFIG asTdpConfig; + ULONG ulReserved[19]; ATOM_AVAILABLE_SCLK_LIST sAvail_SCLK[5]; ULONG ulGMCRestoreResetTime; ULONG ulMinimumNClk; @@ -4809,7 +5035,7 @@ USHORT GnbTdpLimit; USHORT usMaxLVDSPclkFreqInSingleLink; UCHAR ucLvdsMisc; - UCHAR ucLVDSReserved; + UCHAR ucTravisLVDSVolAdjust; UCHAR ucLVDSPwrOnSeqDIGONtoDE_in4Ms; UCHAR ucLVDSPwrOnSeqDEtoVARY_BL_in4Ms; UCHAR ucLVDSPwrOffSeqVARY_BLtoDE_in4Ms; @@ -4817,7 +5043,7 @@ UCHAR ucLVDSOffToOnDelay_in4Ms; UCHAR ucLVDSPwrOnSeqVARY_BLtoBLON_in4Ms; UCHAR ucLVDSPwrOffSeqBLONtoVARY_BL_in4Ms; - UCHAR ucLVDSReserved1; + UCHAR ucMinAllowedBL_Level; ULONG ulLCDBitDepthControlVal; ULONG ulNbpStateMemclkFreq[4]; USHORT usNBP2Voltage; @@ -4846,6 +5072,7 @@ #define SYS_INFO_GPUCAPS__TMDSHDMI_COHERENT_SINGLEPLL_MODE 0x01 #define SYS_INFO_GPUCAPS__DP_SINGLEPLL_MODE 0x02 #define SYS_INFO_GPUCAPS__DISABLE_AUX_MODE_DETECT 0x08 +#define SYS_INFO_GPUCAPS__ENABEL_DFS_BYPASS 0x10 /********************************************************************************************************************** ATOM_INTEGRATED_SYSTEM_INFO_V1_7 Description @@ -4945,6 +5172,9 @@ [bit2] LVDS 888bit per color mode =0: 666 bit per color =1:888 bit per color [bit3] LVDS parameter override enable =0: ucLvdsMisc parameter are not used =1: ucLvdsMisc parameter should be used [bit4] Polarity of signal sent to digital BLON output pin. =0: not inverted(active high) =1: inverted ( active low ) + [bit5] Travid LVDS output voltage override enable, when =1, use ucTravisLVDSVolAdjust value to overwrite Traivs register LVDS_CTRL_4 +ucTravisLVDSVolAdjust When ucLVDSMisc[5]=1,it means platform SBIOS want to overwrite TravisLVDSVoltage. Then VBIOS will use ucTravisLVDSVolAdjust + value to program Travis register LVDS_CTRL_4 ucLVDSPwrOnSeqDIGONtoDE_in4Ms: LVDS power up sequence time in unit of 4ms, time delay from DIGON signal active to data enable signal active( DE ). =0 mean use VBIOS default which is 8 ( 32ms ). The LVDS power up sequence is as following: DIGON->DE->VARY_BL->BLON. This parameter is used by VBIOS only. VBIOS will patch LVDS_InfoTable. @@ -4964,18 +5194,241 @@ =0 means to use VBIOS default delay which is 125 ( 500ms ). This parameter is used by VBIOS only. VBIOS will patch LVDS_InfoTable. -ucLVDSPwrOnVARY_BLtoBLON_in4Ms: LVDS power up sequence time in unit of 4ms. Time delay from VARY_BL signal on to DLON signal active. +ucLVDSPwrOnSeqVARY_BLtoBLON_in4Ms: + LVDS power up sequence time in unit of 4ms. Time delay from VARY_BL signal on to DLON signal active. =0 means to use VBIOS default delay which is 0 ( 0ms ). This parameter is used by VBIOS only. VBIOS will patch LVDS_InfoTable. -ucLVDSPwrOffBLONtoVARY_BL_in4Ms: LVDS power down sequence time in unit of 4ms. Time delay from BLON signal off to VARY_BL signal off. +ucLVDSPwrOffSeqBLONtoVARY_BL_in4Ms: + LVDS power down sequence time in unit of 4ms. Time delay from BLON signal off to VARY_BL signal off. =0 means to use VBIOS default delay which is 0 ( 0ms ). This parameter is used by VBIOS only. VBIOS will patch LVDS_InfoTable. +ucMinAllowedBL_Level: Lowest LCD backlight PWM level. This is customer platform specific parameters. By default it is 0. + ulNbpStateMemclkFreq[4]: system memory clock frequncey in unit of 10Khz in different NB pstate. **********************************************************************************************************************/ +// this IntegrateSystemInfoTable is used for Kaveri & Kabini APU +typedef struct _ATOM_INTEGRATED_SYSTEM_INFO_V1_8 +{ + ATOM_COMMON_TABLE_HEADER sHeader; + ULONG ulBootUpEngineClock; + ULONG ulDentistVCOFreq; + ULONG ulBootUpUMAClock; + ATOM_CLK_VOLT_CAPABILITY sDISPCLK_Voltage[4]; + ULONG ulBootUpReqDisplayVector; + ULONG ulVBIOSMisc; + ULONG ulGPUCapInfo; + ULONG ulDISP_CLK2Freq; + USHORT usRequestedPWMFreqInHz; + UCHAR ucHtcTmpLmt; + UCHAR ucHtcHystLmt; + ULONG ulReserved2; + ULONG ulSystemConfig; + ULONG ulCPUCapInfo; + ULONG ulReserved3; + USHORT usGPUReservedSysMemSize; + USHORT usExtDispConnInfoOffset; + USHORT usPanelRefreshRateRange; + UCHAR ucMemoryType; + UCHAR ucUMAChannelNumber; + UCHAR strVBIOSMsg[40]; + ATOM_TDP_CONFIG asTdpConfig; + ULONG ulReserved[19]; + ATOM_AVAILABLE_SCLK_LIST sAvail_SCLK[5]; + ULONG ulGMCRestoreResetTime; + ULONG ulReserved4; + ULONG ulIdleNClk; + ULONG ulDDR_DLL_PowerUpTime; + ULONG ulDDR_PLL_PowerUpTime; + USHORT usPCIEClkSSPercentage; + USHORT usPCIEClkSSType; + USHORT usLvdsSSPercentage; + USHORT usLvdsSSpreadRateIn10Hz; + USHORT usHDMISSPercentage; + USHORT usHDMISSpreadRateIn10Hz; + USHORT usDVISSPercentage; + USHORT usDVISSpreadRateIn10Hz; + ULONG ulGPUReservedSysMemBaseAddrLo; + ULONG ulGPUReservedSysMemBaseAddrHi; + ULONG ulReserved5[3]; + USHORT usMaxLVDSPclkFreqInSingleLink; + UCHAR ucLvdsMisc; + UCHAR ucTravisLVDSVolAdjust; + UCHAR ucLVDSPwrOnSeqDIGONtoDE_in4Ms; + UCHAR ucLVDSPwrOnSeqDEtoVARY_BL_in4Ms; + UCHAR ucLVDSPwrOffSeqVARY_BLtoDE_in4Ms; + UCHAR ucLVDSPwrOffSeqDEtoDIGON_in4Ms; + UCHAR ucLVDSOffToOnDelay_in4Ms; + UCHAR ucLVDSPwrOnSeqVARY_BLtoBLON_in4Ms; + UCHAR ucLVDSPwrOffSeqBLONtoVARY_BL_in4Ms; + UCHAR ucMinAllowedBL_Level; + ULONG ulLCDBitDepthControlVal; + ULONG ulNbpStateMemclkFreq[4]; + ULONG ulReserved6; + ULONG ulNbpStateNClkFreq[4]; + USHORT usNBPStateVoltage[4]; + USHORT usBootUpNBVoltage; + USHORT usReserved2; + ATOM_EXTERNAL_DISPLAY_CONNECTION_INFO sExtDispConnInfo; +}ATOM_INTEGRATED_SYSTEM_INFO_V1_8; + +/********************************************************************************************************************** + ATOM_INTEGRATED_SYSTEM_INFO_V1_8 Description +ulBootUpEngineClock: VBIOS bootup Engine clock frequency, in 10kHz unit. if it is equal 0, then VBIOS use pre-defined bootup engine clock +ulDentistVCOFreq: Dentist VCO clock in 10kHz unit. +ulBootUpUMAClock: System memory boot up clock frequency in 10Khz unit. +sDISPCLK_Voltage: Report Display clock frequency requirement on GNB voltage(up to 4 voltage levels). + +ulBootUpReqDisplayVector: VBIOS boot up display IDs, following are supported devices in Trinity projects: + ATOM_DEVICE_CRT1_SUPPORT 0x0001 + ATOM_DEVICE_DFP1_SUPPORT 0x0008 + ATOM_DEVICE_DFP6_SUPPORT 0x0040 + ATOM_DEVICE_DFP2_SUPPORT 0x0080 + ATOM_DEVICE_DFP3_SUPPORT 0x0200 + ATOM_DEVICE_DFP4_SUPPORT 0x0400 + ATOM_DEVICE_DFP5_SUPPORT 0x0800 + ATOM_DEVICE_LCD1_SUPPORT 0x0002 + +ulVBIOSMisc: Miscellenous flags for VBIOS requirement and interface + bit[0]=0: INT15 callback function Get LCD EDID ( ax=4e08, bl=1b ) is not supported by SBIOS. + =1: INT15 callback function Get LCD EDID ( ax=4e08, bl=1b ) is supported by SBIOS. + bit[1]=0: INT15 callback function Get boot display( ax=4e08, bl=01h) is not supported by SBIOS + =1: INT15 callback function Get boot display( ax=4e08, bl=01h) is supported by SBIOS + bit[2]=0: INT15 callback function Get panel Expansion ( ax=4e08, bl=02h) is not supported by SBIOS + =1: INT15 callback function Get panel Expansion ( ax=4e08, bl=02h) is supported by SBIOS + bit[3]=0: VBIOS fast boot is disable + =1: VBIOS fast boot is enable. ( VBIOS skip display device detection in every set mode if LCD panel is connect and LID is open) + +ulGPUCapInfo: bit[0~2]= Reserved + bit[3]=0: Enable AUX HW mode detection logic + =1: Disable AUX HW mode detection logic + bit[4]=0: Disable DFS bypass feature + =1: Enable DFS bypass feature + +usRequestedPWMFreqInHz: When it's set to 0x0 by SBIOS: the LCD BackLight is not controlled by GPU(SW). + Any attempt to change BL using VBIOS function or enable VariBri from PP table is not effective since ATOM_BIOS_INFO_BL_CONTROLLED_BY_GPU==0; + + When it's set to a non-zero frequency, the BackLight is controlled by GPU (SW) in one of two ways below: + 1. SW uses the GPU BL PWM output to control the BL, in chis case, this non-zero frequency determines what freq GPU should use; + VBIOS will set up proper PWM frequency and ATOM_BIOS_INFO_BL_CONTROLLED_BY_GPU==1,as the result, + Changing BL using VBIOS function is functional in both driver and non-driver present environment; + and enabling VariBri under the driver environment from PP table is optional. + + 2. SW uses other means to control BL (like DPCD),this non-zero frequency serves as a flag only indicating + that BL control from GPU is expected. + VBIOS will NOT set up PWM frequency but make ATOM_BIOS_INFO_BL_CONTROLLED_BY_GPU==1 + Changing BL using VBIOS function could be functional in both driver and non-driver present environment,but + it's per platform + and enabling VariBri under the driver environment from PP table is optional. + +ucHtcTmpLmt: Refer to D18F3x64 bit[22:16], HtcTmpLmt. Threshold on value to enter HTC_active state. +ucHtcHystLmt: Refer to D18F3x64 bit[27:24], HtcHystLmt. + To calculate threshold off value to exit HTC_active state, which is Threshold on vlaue minus ucHtcHystLmt. + +ulSystemConfig: Bit[0]=0: PCIE Power Gating Disabled + =1: PCIE Power Gating Enabled + Bit[1]=0: DDR-DLL shut-down feature disabled. + 1: DDR-DLL shut-down feature enabled. + Bit[2]=0: DDR-PLL Power down feature disabled. + 1: DDR-PLL Power down feature enabled. + Bit[3]=0: GNB DPM is disabled + =1: GNB DPM is enabled +ulCPUCapInfo: TBD + +usExtDispConnInfoOffset: Offset to sExtDispConnInfo inside the structure +usPanelRefreshRateRange: Bit vector for LCD supported refresh rate range. If DRR is requestd by the platform, at least two bits need to be set + to indicate a range. + SUPPORTED_LCD_REFRESHRATE_30Hz 0x0004 + SUPPORTED_LCD_REFRESHRATE_40Hz 0x0008 + SUPPORTED_LCD_REFRESHRATE_50Hz 0x0010 + SUPPORTED_LCD_REFRESHRATE_60Hz 0x0020 + +ucMemoryType: [3:0]=1:DDR1;=2:DDR2;=3:DDR3;=5:GDDR5; [7:4] is reserved. +ucUMAChannelNumber: System memory channel numbers. + +strVBIOSMsg[40]: VBIOS boot up customized message string + +sAvail_SCLK[5]: Arrays to provide availabe list of SLCK and corresponding voltage, order from low to high + +ulGMCRestoreResetTime: GMC power restore and GMC reset time to calculate data reconnection latency. Unit in ns. +ulIdleNClk: NCLK speed while memory runs in self-refresh state, used to calculate self-refresh latency. Unit in 10kHz. +ulDDR_DLL_PowerUpTime: DDR PHY DLL power up time. Unit in ns. +ulDDR_PLL_PowerUpTime: DDR PHY PLL power up time. Unit in ns. + +usPCIEClkSSPercentage: PCIE Clock Spread Spectrum Percentage in unit 0.01%; 100 mean 1%. +usPCIEClkSSType: PCIE Clock Spread Spectrum Type. 0 for Down spread(default); 1 for Center spread. +usLvdsSSPercentage: LVDS panel ( not include eDP ) Spread Spectrum Percentage in unit of 0.01%, =0, use VBIOS default setting. +usLvdsSSpreadRateIn10Hz: LVDS panel ( not include eDP ) Spread Spectrum frequency in unit of 10Hz, =0, use VBIOS default setting. +usHDMISSPercentage: HDMI Spread Spectrum Percentage in unit 0.01%; 100 mean 1%, =0, use VBIOS default setting. +usHDMISSpreadRateIn10Hz: HDMI Spread Spectrum frequency in unit of 10Hz, =0, use VBIOS default setting. +usDVISSPercentage: DVI Spread Spectrum Percentage in unit 0.01%; 100 mean 1%, =0, use VBIOS default setting. +usDVISSpreadRateIn10Hz: DVI Spread Spectrum frequency in unit of 10Hz, =0, use VBIOS default setting. + +usGPUReservedSysMemSize: Reserved system memory size for ACP engine in APU GNB, units in MB. 0/2/4MB based on CMOS options, current default could be 0MB. KV only, not on KB. +ulGPUReservedSysMemBaseAddrLo: Low 32 bits base address to the reserved system memory. +ulGPUReservedSysMemBaseAddrHi: High 32 bits base address to the reserved system memory. + +usMaxLVDSPclkFreqInSingleLink: Max pixel clock LVDS panel single link, if=0 means VBIOS use default threhold, right now it is 85Mhz +ucLVDSMisc: [bit0] LVDS 888bit panel mode =0: LVDS 888 panel in LDI mode, =1: LVDS 888 panel in FPDI mode + [bit1] LVDS panel lower and upper link mapping =0: lower link and upper link not swap, =1: lower link and upper link are swapped + [bit2] LVDS 888bit per color mode =0: 666 bit per color =1:888 bit per color + [bit3] LVDS parameter override enable =0: ucLvdsMisc parameter are not used =1: ucLvdsMisc parameter should be used + [bit4] Polarity of signal sent to digital BLON output pin. =0: not inverted(active high) =1: inverted ( active low ) + [bit5] Travid LVDS output voltage override enable, when =1, use ucTravisLVDSVolAdjust value to overwrite Traivs register LVDS_CTRL_4 +ucTravisLVDSVolAdjust When ucLVDSMisc[5]=1,it means platform SBIOS want to overwrite TravisLVDSVoltage. Then VBIOS will use ucTravisLVDSVolAdjust + value to program Travis register LVDS_CTRL_4 +ucLVDSPwrOnSeqDIGONtoDE_in4Ms: + LVDS power up sequence time in unit of 4ms, time delay from DIGON signal active to data enable signal active( DE ). + =0 mean use VBIOS default which is 8 ( 32ms ). The LVDS power up sequence is as following: DIGON->DE->VARY_BL->BLON. + This parameter is used by VBIOS only. VBIOS will patch LVDS_InfoTable. +ucLVDSPwrOnDEtoVARY_BL_in4Ms: + LVDS power up sequence time in unit of 4ms., time delay from DE( data enable ) active to Vary Brightness enable signal active( VARY_BL ). + =0 mean use VBIOS default which is 90 ( 360ms ). The LVDS power up sequence is as following: DIGON->DE->VARY_BL->BLON. + This parameter is used by VBIOS only. VBIOS will patch LVDS_InfoTable. +ucLVDSPwrOffVARY_BLtoDE_in4Ms: + LVDS power down sequence time in unit of 4ms, time delay from data enable ( DE ) signal off to LCDVCC (DIGON) off. + =0 mean use VBIOS default delay which is 8 ( 32ms ). The LVDS power down sequence is as following: BLON->VARY_BL->DE->DIGON + This parameter is used by VBIOS only. VBIOS will patch LVDS_InfoTable. +ucLVDSPwrOffDEtoDIGON_in4Ms: + LVDS power down sequence time in unit of 4ms, time delay from vary brightness enable signal( VARY_BL) off to data enable ( DE ) signal off. + =0 mean use VBIOS default which is 90 ( 360ms ). The LVDS power down sequence is as following: BLON->VARY_BL->DE->DIGON + This parameter is used by VBIOS only. VBIOS will patch LVDS_InfoTable. +ucLVDSOffToOnDelay_in4Ms: + LVDS power down sequence time in unit of 4ms. Time delay from DIGON signal off to DIGON signal active. + =0 means to use VBIOS default delay which is 125 ( 500ms ). + This parameter is used by VBIOS only. VBIOS will patch LVDS_InfoTable. +ucLVDSPwrOnSeqVARY_BLtoBLON_in4Ms: + LVDS power up sequence time in unit of 4ms. Time delay from VARY_BL signal on to DLON signal active. + =0 means to use VBIOS default delay which is 0 ( 0ms ). + This parameter is used by VBIOS only. VBIOS will patch LVDS_InfoTable. + +ucLVDSPwrOffSeqBLONtoVARY_BL_in4Ms: + LVDS power down sequence time in unit of 4ms. Time delay from BLON signal off to VARY_BL signal off. + =0 means to use VBIOS default delay which is 0 ( 0ms ). + This parameter is used by VBIOS only. VBIOS will patch LVDS_InfoTable. +ucMinAllowedBL_Level: Lowest LCD backlight PWM level. This is customer platform specific parameters. By default it is 0. + +ulLCDBitDepthControlVal: GPU display control encoder bit dither control setting, used to program register mmFMT_BIT_DEPTH_CONTROL + +ulNbpStateMemclkFreq[4]: system memory clock frequncey in unit of 10Khz in different NB P-State(P0, P1, P2 & P3). +ulNbpStateNClkFreq[4]: NB P-State NClk frequency in different NB P-State +usNBPStateVoltage[4]: NB P-State (P0/P1 & P2/P3) voltage; NBP3 refers to lowes voltage +usBootUpNBVoltage: NB P-State voltage during boot up before driver loaded +sExtDispConnInfo: Display connector information table provided to VBIOS + +**********************************************************************************************************************/ + +// this Table is used for Kaveri/Kabini APU +typedef struct _ATOM_FUSION_SYSTEM_INFO_V2 +{ + ATOM_INTEGRATED_SYSTEM_INFO_V1_8 sIntegratedSysInfo; // refer to ATOM_INTEGRATED_SYSTEM_INFO_V1_8 definition + ULONG ulPowerplayTable[128]; // Update comments here to link new powerplay table definition structure +}ATOM_FUSION_SYSTEM_INFO_V2; + + /**************************************************************************/ // This portion is only used when ext thermal chip or engine/memory clock SS chip is populated on a design //Memory SS Info Table @@ -5026,22 +5479,24 @@ //Define ucClockIndication, SW uses the IDs below to search if the SS is required/enabled on a clock branch/signal type. //SS is not required or enabled if a match is not found. -#define ASIC_INTERNAL_MEMORY_SS 1 -#define ASIC_INTERNAL_ENGINE_SS 2 -#define ASIC_INTERNAL_UVD_SS 3 -#define ASIC_INTERNAL_SS_ON_TMDS 4 -#define ASIC_INTERNAL_SS_ON_HDMI 5 -#define ASIC_INTERNAL_SS_ON_LVDS 6 -#define ASIC_INTERNAL_SS_ON_DP 7 -#define ASIC_INTERNAL_SS_ON_DCPLL 8 -#define ASIC_EXTERNAL_SS_ON_DP_CLOCK 9 -#define ASIC_INTERNAL_VCE_SS 10 +#define ASIC_INTERNAL_MEMORY_SS 1 +#define ASIC_INTERNAL_ENGINE_SS 2 +#define ASIC_INTERNAL_UVD_SS 3 +#define ASIC_INTERNAL_SS_ON_TMDS 4 +#define ASIC_INTERNAL_SS_ON_HDMI 5 +#define ASIC_INTERNAL_SS_ON_LVDS 6 +#define ASIC_INTERNAL_SS_ON_DP 7 +#define ASIC_INTERNAL_SS_ON_DCPLL 8 +#define ASIC_EXTERNAL_SS_ON_DP_CLOCK 9 +#define ASIC_INTERNAL_VCE_SS 10 +#define ASIC_INTERNAL_GPUPLL_SS 11 + typedef struct _ATOM_ASIC_SS_ASSIGNMENT_V2 { ULONG ulTargetClockRange; //For mem/engine/uvd, Clock Out frequence (VCO ), in unit of 10Khz //For TMDS/HDMI/LVDS, it is pixel clock , for DP, it is link clock ( 27000 or 16200 ) - USHORT usSpreadSpectrumPercentage; //in unit of 0.01% + USHORT usSpreadSpectrumPercentage; //in unit of 0.01% or 0.001%, decided by ucSpreadSpectrumMode bit4 USHORT usSpreadRateIn10Hz; //in unit of 10Hz, modulation freq UCHAR ucClockIndication; //Indicate which clock source needs SS UCHAR ucSpreadSpectrumMode; //Bit0=0 Down Spread,=1 Center Spread, bit1=0: internal SS bit1=1: external SS @@ -5079,6 +5534,11 @@ UCHAR ucReserved[2]; }ATOM_ASIC_SS_ASSIGNMENT_V3; +//ATOM_ASIC_SS_ASSIGNMENT_V3.ucSpreadSpectrumMode +#define SS_MODE_V3_CENTRE_SPREAD_MASK 0x01 +#define SS_MODE_V3_EXTERNAL_SS_MASK 0x02 +#define SS_MODE_V3_PERCENTAGE_DIV_BY_1000_MASK 0x10 + typedef struct _ATOM_ASIC_INTERNAL_SS_INFO_V3 { ATOM_COMMON_TABLE_HEADER sHeader; @@ -5447,6 +5907,8 @@ #define ATOM_S7_DOS_MODE_PIXEL_DEPTHb0 0x0C #define ATOM_S7_DOS_MODE_PIXEL_FORMATb0 0xF0 #define ATOM_S7_DOS_8BIT_DAC_ENb1 0x01 +#define ATOM_S7_ASIC_INIT_COMPLETEb1 0x02 +#define ATOM_S7_ASIC_INIT_COMPLETE_MASK 0x00000200 #define ATOM_S7_DOS_MODE_NUMBERw1 0x0FFFF #define ATOM_S7_DOS_8BIT_DAC_EN_SHIFT 8 @@ -5719,6 +6181,7 @@ #define INDIRECT_IO_PCIE 3 #define INDIRECT_IO_PCIEP 4 #define INDIRECT_IO_NBMISC 5 +#define INDIRECT_IO_SMU 5 #define INDIRECT_IO_PLL_READ INDIRECT_IO_PLL | INDIRECT_READ #define INDIRECT_IO_PLL_WRITE INDIRECT_IO_PLL | INDIRECT_WRITE @@ -5730,6 +6193,8 @@ #define INDIRECT_IO_PCIEP_WRITE INDIRECT_IO_PCIEP | INDIRECT_WRITE #define INDIRECT_IO_NBMISC_READ INDIRECT_IO_NBMISC | INDIRECT_READ #define INDIRECT_IO_NBMISC_WRITE INDIRECT_IO_NBMISC | INDIRECT_WRITE +#define INDIRECT_IO_SMU_READ INDIRECT_IO_SMU | INDIRECT_READ +#define INDIRECT_IO_SMU_WRITE INDIRECT_IO_SMU | INDIRECT_WRITE typedef struct _ATOM_OEM_INFO { @@ -5875,8 +6340,10 @@ #define _64Mx32 0x43 #define _128Mx8 0x51 #define _128Mx16 0x52 +#define _128Mx32 0x53 #define _256Mx8 0x61 #define _256Mx16 0x62 +#define _512Mx8 0x71 #define SAMSUNG 0x1 #define INFINEON 0x2 @@ -5893,6 +6360,8 @@ #define PROMOS MOSEL #define KRETON INFINEON #define ELIXIR NANYA +#define MEZZA ELPIDA + /////////////Support for GDDR5 MC uCode to reside in upper 64K of ROM///////////// @@ -6620,11 +7089,16 @@ UCHAR ucMaxDispEngineNum; UCHAR ucMaxActiveDispEngineNum; UCHAR ucMaxPPLLNum; - UCHAR ucCoreRefClkSource; // value of CORE_REF_CLK_SOURCE - UCHAR ucReserved[3]; - ASIC_TRANSMITTER_INFO_V2 asTransmitterInfo[1]; // for alligment only + UCHAR ucCoreRefClkSource; // value of CORE_REF_CLK_SOURCE + UCHAR ucDispCaps; + UCHAR ucReserved[2]; + ASIC_TRANSMITTER_INFO_V2 asTransmitterInfo[1]; // for alligment only }ATOM_DISP_OUT_INFO_V3; +//ucDispCaps +#define DISPLAY_CAPS__DP_PCLK_FROM_PPLL 0x01 +#define DISPLAY_CAPS__FORCE_DISPDEV_CONNECTED 0x02 + typedef enum CORE_REF_CLK_SOURCE{ CLOCK_SRC_XTALIN=0, CLOCK_SRC_XO_IN=1, @@ -6829,6 +7303,17 @@ USHORT usPhyPllSettingOffset; // offset of CLOCK_CONDITION_SETTING_ENTRY* with Phy Pll Settings }DIG_TRANSMITTER_INFO_HEADER_V3_1; +typedef struct _DIG_TRANSMITTER_INFO_HEADER_V3_2{ + ATOM_COMMON_TABLE_HEADER sHeader; + USHORT usDPVsPreEmphSettingOffset; // offset of PHY_ANALOG_SETTING_INFO * with DP Voltage Swing and Pre-Emphasis for each Link clock + USHORT usPhyAnalogRegListOffset; // offset of CLOCK_CONDITION_REGESTER_INFO* with None-DP mode Analog Setting's register Info + USHORT usPhyAnalogSettingOffset; // offset of CLOCK_CONDITION_SETTING_ENTRY* with None-DP mode Analog Setting for each link clock range + USHORT usPhyPllRegListOffset; // offset of CLOCK_CONDITION_REGESTER_INFO* with Phy Pll register Info + USHORT usPhyPllSettingOffset; // offset of CLOCK_CONDITION_SETTING_ENTRY* with Phy Pll Settings + USHORT usDPSSRegListOffset; // offset of CLOCK_CONDITION_REGESTER_INFO* with Phy SS Pll register Info + USHORT usDPSSSettingOffset; // offset of CLOCK_CONDITION_SETTING_ENTRY* with Phy SS Pll Settings +}DIG_TRANSMITTER_INFO_HEADER_V3_2; + typedef struct _CLOCK_CONDITION_REGESTER_INFO{ USHORT usRegisterIndex; UCHAR ucStartBit; @@ -6852,12 +7337,24 @@ ULONG ulRegVal; }PHY_CONDITION_REG_VAL; +typedef struct _PHY_CONDITION_REG_VAL_V2{ + ULONG ulCondition; + UCHAR ucCondition2; + ULONG ulRegVal; +}PHY_CONDITION_REG_VAL_V2; + typedef struct _PHY_CONDITION_REG_INFO{ USHORT usRegIndex; USHORT usSize; PHY_CONDITION_REG_VAL asRegVal[1]; }PHY_CONDITION_REG_INFO; +typedef struct _PHY_CONDITION_REG_INFO_V2{ + USHORT usRegIndex; + USHORT usSize; + PHY_CONDITION_REG_VAL_V2 asRegVal[1]; +}PHY_CONDITION_REG_INFO_V2; + typedef struct _PHY_ANALOG_SETTING_INFO{ UCHAR ucEncodeMode; UCHAR ucPhySel; @@ -6865,6 +7362,25 @@ PHY_CONDITION_REG_INFO asAnalogSetting[1]; }PHY_ANALOG_SETTING_INFO; +typedef struct _PHY_ANALOG_SETTING_INFO_V2{ + UCHAR ucEncodeMode; + UCHAR ucPhySel; + USHORT usSize; + PHY_CONDITION_REG_INFO_V2 asAnalogSetting[1]; +}PHY_ANALOG_SETTING_INFO_V2; + +typedef struct _GFX_HAVESTING_PARAMETERS { + UCHAR ucGfxBlkId; //GFX blk id to be harvested, like CU, RB or PRIM + UCHAR ucReserved; //reserved + UCHAR ucActiveUnitNumPerSH; //requested active CU/RB/PRIM number per shader array + UCHAR ucMaxUnitNumPerSH; //max CU/RB/PRIM number per shader array +} GFX_HAVESTING_PARAMETERS; + +//ucGfxBlkId +#define GFX_HARVESTING_CU_ID 0 +#define GFX_HARVESTING_RB_ID 1 +#define GFX_HARVESTING_PRIM_ID 2 + /****************************************************************************/ //Portion VI: Definitinos for vbios MC scratch registers that driver used /****************************************************************************/ @@ -6875,8 +7391,17 @@ #define MC_MISC0__MEMORY_TYPE__GDDR3 0x30000000 #define MC_MISC0__MEMORY_TYPE__GDDR4 0x40000000 #define MC_MISC0__MEMORY_TYPE__GDDR5 0x50000000 +#define MC_MISC0__MEMORY_TYPE__HBM 0x60000000 #define MC_MISC0__MEMORY_TYPE__DDR3 0xB0000000 +#define ATOM_MEM_TYPE_DDR_STRING "DDR" +#define ATOM_MEM_TYPE_DDR2_STRING "DDR2" +#define ATOM_MEM_TYPE_GDDR3_STRING "GDDR3" +#define ATOM_MEM_TYPE_GDDR4_STRING "GDDR4" +#define ATOM_MEM_TYPE_GDDR5_STRING "GDDR5" +#define ATOM_MEM_TYPE_HBM_STRING "HBM" +#define ATOM_MEM_TYPE_DDR3_STRING "DDR3" + /****************************************************************************/ //Portion VI: Definitinos being oboselete /****************************************************************************/ @@ -7239,565 +7764,6 @@ ATOM_POWERMODE_INFO_V3 asPowerPlayInfo[ATOM_MAX_NUMBEROF_POWER_BLOCK]; }ATOM_POWERPLAY_INFO_V3; -/* New PPlib */ -/**************************************************************************/ -typedef struct _ATOM_PPLIB_THERMALCONTROLLER - -{ - UCHAR ucType; // one of ATOM_PP_THERMALCONTROLLER_* - UCHAR ucI2cLine; // as interpreted by DAL I2C - UCHAR ucI2cAddress; - UCHAR ucFanParameters; // Fan Control Parameters. - UCHAR ucFanMinRPM; // Fan Minimum RPM (hundreds) -- for display purposes only. - UCHAR ucFanMaxRPM; // Fan Maximum RPM (hundreds) -- for display purposes only. - UCHAR ucReserved; // ---- - UCHAR ucFlags; // to be defined -} ATOM_PPLIB_THERMALCONTROLLER; - -#define ATOM_PP_FANPARAMETERS_TACHOMETER_PULSES_PER_REVOLUTION_MASK 0x0f -#define ATOM_PP_FANPARAMETERS_NOFAN 0x80 // No fan is connected to this controller. - -#define ATOM_PP_THERMALCONTROLLER_NONE 0 -#define ATOM_PP_THERMALCONTROLLER_LM63 1 // Not used by PPLib -#define ATOM_PP_THERMALCONTROLLER_ADM1032 2 // Not used by PPLib -#define ATOM_PP_THERMALCONTROLLER_ADM1030 3 // Not used by PPLib -#define ATOM_PP_THERMALCONTROLLER_MUA6649 4 // Not used by PPLib -#define ATOM_PP_THERMALCONTROLLER_LM64 5 -#define ATOM_PP_THERMALCONTROLLER_F75375 6 // Not used by PPLib -#define ATOM_PP_THERMALCONTROLLER_RV6xx 7 -#define ATOM_PP_THERMALCONTROLLER_RV770 8 -#define ATOM_PP_THERMALCONTROLLER_ADT7473 9 -#define ATOM_PP_THERMALCONTROLLER_EXTERNAL_GPIO 11 -#define ATOM_PP_THERMALCONTROLLER_EVERGREEN 12 -#define ATOM_PP_THERMALCONTROLLER_EMC2103 13 /* 0x0D */ // Only fan control will be implemented, do NOT show this in PPGen. -#define ATOM_PP_THERMALCONTROLLER_SUMO 14 /* 0x0E */ // Sumo type, used internally -#define ATOM_PP_THERMALCONTROLLER_NISLANDS 15 -#define ATOM_PP_THERMALCONTROLLER_SISLANDS 16 -#define ATOM_PP_THERMALCONTROLLER_LM96163 17 - -// Thermal controller 'combo type' to use an external controller for Fan control and an internal controller for thermal. -// We probably should reserve the bit 0x80 for this use. -// To keep the number of these types low we should also use the same code for all ASICs (i.e. do not distinguish RV6xx and RV7xx Internal here). -// The driver can pick the correct internal controller based on the ASIC. - -#define ATOM_PP_THERMALCONTROLLER_ADT7473_WITH_INTERNAL 0x89 // ADT7473 Fan Control + Internal Thermal Controller -#define ATOM_PP_THERMALCONTROLLER_EMC2103_WITH_INTERNAL 0x8D // EMC2103 Fan Control + Internal Thermal Controller - -typedef struct _ATOM_PPLIB_STATE -{ - UCHAR ucNonClockStateIndex; - UCHAR ucClockStateIndices[1]; // variable-sized -} ATOM_PPLIB_STATE; - - -typedef struct _ATOM_PPLIB_FANTABLE -{ - UCHAR ucFanTableFormat; // Change this if the table format changes or version changes so that the other fields are not the same. - UCHAR ucTHyst; // Temperature hysteresis. Integer. - USHORT usTMin; // The temperature, in 0.01 centigrades, below which we just run at a minimal PWM. - USHORT usTMed; // The middle temperature where we change slopes. - USHORT usTHigh; // The high point above TMed for adjusting the second slope. - USHORT usPWMMin; // The minimum PWM value in percent (0.01% increments). - USHORT usPWMMed; // The PWM value (in percent) at TMed. - USHORT usPWMHigh; // The PWM value at THigh. -} ATOM_PPLIB_FANTABLE; - -typedef struct _ATOM_PPLIB_FANTABLE2 -{ - ATOM_PPLIB_FANTABLE basicTable; - USHORT usTMax; // The max temperature -} ATOM_PPLIB_FANTABLE2; - -typedef struct _ATOM_PPLIB_EXTENDEDHEADER -{ - USHORT usSize; - ULONG ulMaxEngineClock; // For Overdrive. - ULONG ulMaxMemoryClock; // For Overdrive. - // Add extra system parameters here, always adjust size to include all fields. - USHORT usVCETableOffset; //points to ATOM_PPLIB_VCE_Table - USHORT usUVDTableOffset; //points to ATOM_PPLIB_UVD_Table -} ATOM_PPLIB_EXTENDEDHEADER; - -//// ATOM_PPLIB_POWERPLAYTABLE::ulPlatformCaps -#define ATOM_PP_PLATFORM_CAP_BACKBIAS 1 -#define ATOM_PP_PLATFORM_CAP_POWERPLAY 2 -#define ATOM_PP_PLATFORM_CAP_SBIOSPOWERSOURCE 4 -#define ATOM_PP_PLATFORM_CAP_ASPM_L0s 8 -#define ATOM_PP_PLATFORM_CAP_ASPM_L1 16 -#define ATOM_PP_PLATFORM_CAP_HARDWAREDC 32 -#define ATOM_PP_PLATFORM_CAP_GEMINIPRIMARY 64 -#define ATOM_PP_PLATFORM_CAP_STEPVDDC 128 -#define ATOM_PP_PLATFORM_CAP_VOLTAGECONTROL 256 -#define ATOM_PP_PLATFORM_CAP_SIDEPORTCONTROL 512 -#define ATOM_PP_PLATFORM_CAP_TURNOFFPLL_ASPML1 1024 -#define ATOM_PP_PLATFORM_CAP_HTLINKCONTROL 2048 -#define ATOM_PP_PLATFORM_CAP_MVDDCONTROL 4096 -#define ATOM_PP_PLATFORM_CAP_GOTO_BOOT_ON_ALERT 0x2000 // Go to boot state on alerts, e.g. on an AC->DC transition. -#define ATOM_PP_PLATFORM_CAP_DONT_WAIT_FOR_VBLANK_ON_ALERT 0x4000 // Do NOT wait for VBLANK during an alert (e.g. AC->DC transition). -#define ATOM_PP_PLATFORM_CAP_VDDCI_CONTROL 0x8000 // Does the driver control VDDCI independently from VDDC. -#define ATOM_PP_PLATFORM_CAP_REGULATOR_HOT 0x00010000 // Enable the 'regulator hot' feature. -#define ATOM_PP_PLATFORM_CAP_BACO 0x00020000 // Does the driver supports BACO state. - - -typedef struct _ATOM_PPLIB_POWERPLAYTABLE -{ - ATOM_COMMON_TABLE_HEADER sHeader; - - UCHAR ucDataRevision; - - UCHAR ucNumStates; - UCHAR ucStateEntrySize; - UCHAR ucClockInfoSize; - UCHAR ucNonClockSize; - - // offset from start of this table to array of ucNumStates ATOM_PPLIB_STATE structures - USHORT usStateArrayOffset; - - // offset from start of this table to array of ASIC-specific structures, - // currently ATOM_PPLIB_CLOCK_INFO. - USHORT usClockInfoArrayOffset; - - // offset from start of this table to array of ATOM_PPLIB_NONCLOCK_INFO - USHORT usNonClockInfoArrayOffset; - - USHORT usBackbiasTime; // in microseconds - USHORT usVoltageTime; // in microseconds - USHORT usTableSize; //the size of this structure, or the extended structure - - ULONG ulPlatformCaps; // See ATOM_PPLIB_CAPS_* - - ATOM_PPLIB_THERMALCONTROLLER sThermalController; - - USHORT usBootClockInfoOffset; - USHORT usBootNonClockInfoOffset; - -} ATOM_PPLIB_POWERPLAYTABLE; - -typedef struct _ATOM_PPLIB_POWERPLAYTABLE2 -{ - ATOM_PPLIB_POWERPLAYTABLE basicTable; - UCHAR ucNumCustomThermalPolicy; - USHORT usCustomThermalPolicyArrayOffset; -}ATOM_PPLIB_POWERPLAYTABLE2, *LPATOM_PPLIB_POWERPLAYTABLE2; - -typedef struct _ATOM_PPLIB_POWERPLAYTABLE3 -{ - ATOM_PPLIB_POWERPLAYTABLE2 basicTable2; - USHORT usFormatID; // To be used ONLY by PPGen. - USHORT usFanTableOffset; - USHORT usExtendendedHeaderOffset; -} ATOM_PPLIB_POWERPLAYTABLE3, *LPATOM_PPLIB_POWERPLAYTABLE3; - -typedef struct _ATOM_PPLIB_POWERPLAYTABLE4 -{ - ATOM_PPLIB_POWERPLAYTABLE3 basicTable3; - ULONG ulGoldenPPID; // PPGen use only - ULONG ulGoldenRevision; // PPGen use only - USHORT usVddcDependencyOnSCLKOffset; - USHORT usVddciDependencyOnMCLKOffset; - USHORT usVddcDependencyOnMCLKOffset; - USHORT usMaxClockVoltageOnDCOffset; - USHORT usVddcPhaseShedLimitsTableOffset; // Points to ATOM_PPLIB_PhaseSheddingLimits_Table - USHORT usReserved; -} ATOM_PPLIB_POWERPLAYTABLE4, *LPATOM_PPLIB_POWERPLAYTABLE4; - -typedef struct _ATOM_PPLIB_POWERPLAYTABLE5 -{ - ATOM_PPLIB_POWERPLAYTABLE4 basicTable4; - ULONG ulTDPLimit; - ULONG ulNearTDPLimit; - ULONG ulSQRampingThreshold; - USHORT usCACLeakageTableOffset; // Points to ATOM_PPLIB_CAC_Leakage_Table - ULONG ulCACLeakage; // The iLeakage for driver calculated CAC leakage table - USHORT usTDPODLimit; - USHORT usLoadLineSlope; // in milliOhms * 100 -} ATOM_PPLIB_POWERPLAYTABLE5, *LPATOM_PPLIB_POWERPLAYTABLE5; - -//// ATOM_PPLIB_NONCLOCK_INFO::usClassification -#define ATOM_PPLIB_CLASSIFICATION_UI_MASK 0x0007 -#define ATOM_PPLIB_CLASSIFICATION_UI_SHIFT 0 -#define ATOM_PPLIB_CLASSIFICATION_UI_NONE 0 -#define ATOM_PPLIB_CLASSIFICATION_UI_BATTERY 1 -#define ATOM_PPLIB_CLASSIFICATION_UI_BALANCED 3 -#define ATOM_PPLIB_CLASSIFICATION_UI_PERFORMANCE 5 -// 2, 4, 6, 7 are reserved - -#define ATOM_PPLIB_CLASSIFICATION_BOOT 0x0008 -#define ATOM_PPLIB_CLASSIFICATION_THERMAL 0x0010 -#define ATOM_PPLIB_CLASSIFICATION_LIMITEDPOWERSOURCE 0x0020 -#define ATOM_PPLIB_CLASSIFICATION_REST 0x0040 -#define ATOM_PPLIB_CLASSIFICATION_FORCED 0x0080 -#define ATOM_PPLIB_CLASSIFICATION_3DPERFORMANCE 0x0100 -#define ATOM_PPLIB_CLASSIFICATION_OVERDRIVETEMPLATE 0x0200 -#define ATOM_PPLIB_CLASSIFICATION_UVDSTATE 0x0400 -#define ATOM_PPLIB_CLASSIFICATION_3DLOW 0x0800 -#define ATOM_PPLIB_CLASSIFICATION_ACPI 0x1000 -#define ATOM_PPLIB_CLASSIFICATION_HD2STATE 0x2000 -#define ATOM_PPLIB_CLASSIFICATION_HDSTATE 0x4000 -#define ATOM_PPLIB_CLASSIFICATION_SDSTATE 0x8000 - -//// ATOM_PPLIB_NONCLOCK_INFO::usClassification2 -#define ATOM_PPLIB_CLASSIFICATION2_LIMITEDPOWERSOURCE_2 0x0001 -#define ATOM_PPLIB_CLASSIFICATION2_ULV 0x0002 -#define ATOM_PPLIB_CLASSIFICATION2_MVC 0x0004 //Multi-View Codec (BD-3D) - -//// ATOM_PPLIB_NONCLOCK_INFO::ulCapsAndSettings -#define ATOM_PPLIB_SINGLE_DISPLAY_ONLY 0x00000001 -#define ATOM_PPLIB_SUPPORTS_VIDEO_PLAYBACK 0x00000002 - -// 0 is 2.5Gb/s, 1 is 5Gb/s -#define ATOM_PPLIB_PCIE_LINK_SPEED_MASK 0x00000004 -#define ATOM_PPLIB_PCIE_LINK_SPEED_SHIFT 2 - -// lanes - 1: 1, 2, 4, 8, 12, 16 permitted by PCIE spec -#define ATOM_PPLIB_PCIE_LINK_WIDTH_MASK 0x000000F8 -#define ATOM_PPLIB_PCIE_LINK_WIDTH_SHIFT 3 - -// lookup into reduced refresh-rate table -#define ATOM_PPLIB_LIMITED_REFRESHRATE_VALUE_MASK 0x00000F00 -#define ATOM_PPLIB_LIMITED_REFRESHRATE_VALUE_SHIFT 8 - -#define ATOM_PPLIB_LIMITED_REFRESHRATE_UNLIMITED 0 -#define ATOM_PPLIB_LIMITED_REFRESHRATE_50HZ 1 -// 2-15 TBD as needed. - -#define ATOM_PPLIB_SOFTWARE_DISABLE_LOADBALANCING 0x00001000 -#define ATOM_PPLIB_SOFTWARE_ENABLE_SLEEP_FOR_TIMESTAMPS 0x00002000 - -#define ATOM_PPLIB_DISALLOW_ON_DC 0x00004000 - -#define ATOM_PPLIB_ENABLE_VARIBRIGHT 0x00008000 - -//memory related flags -#define ATOM_PPLIB_SWSTATE_MEMORY_DLL_OFF 0x000010000 - -//M3 Arb //2bits, current 3 sets of parameters in total -#define ATOM_PPLIB_M3ARB_MASK 0x00060000 -#define ATOM_PPLIB_M3ARB_SHIFT 17 - -#define ATOM_PPLIB_ENABLE_DRR 0x00080000 - -// remaining 16 bits are reserved -typedef struct _ATOM_PPLIB_THERMAL_STATE -{ - UCHAR ucMinTemperature; - UCHAR ucMaxTemperature; - UCHAR ucThermalAction; -}ATOM_PPLIB_THERMAL_STATE, *LPATOM_PPLIB_THERMAL_STATE; - -// Contained in an array starting at the offset -// in ATOM_PPLIB_POWERPLAYTABLE::usNonClockInfoArrayOffset. -// referenced from ATOM_PPLIB_STATE_INFO::ucNonClockStateIndex -#define ATOM_PPLIB_NONCLOCKINFO_VER1 12 -#define ATOM_PPLIB_NONCLOCKINFO_VER2 24 -typedef struct _ATOM_PPLIB_NONCLOCK_INFO -{ - USHORT usClassification; - UCHAR ucMinTemperature; - UCHAR ucMaxTemperature; - ULONG ulCapsAndSettings; - UCHAR ucRequiredPower; - USHORT usClassification2; - ULONG ulVCLK; - ULONG ulDCLK; - UCHAR ucUnused[5]; -} ATOM_PPLIB_NONCLOCK_INFO; - -// Contained in an array starting at the offset -// in ATOM_PPLIB_POWERPLAYTABLE::usClockInfoArrayOffset. -// referenced from ATOM_PPLIB_STATE::ucClockStateIndices -typedef struct _ATOM_PPLIB_R600_CLOCK_INFO -{ - USHORT usEngineClockLow; - UCHAR ucEngineClockHigh; - - USHORT usMemoryClockLow; - UCHAR ucMemoryClockHigh; - - USHORT usVDDC; - USHORT usUnused1; - USHORT usUnused2; - - ULONG ulFlags; // ATOM_PPLIB_R600_FLAGS_* - -} ATOM_PPLIB_R600_CLOCK_INFO; - -// ulFlags in ATOM_PPLIB_R600_CLOCK_INFO -#define ATOM_PPLIB_R600_FLAGS_PCIEGEN2 1 -#define ATOM_PPLIB_R600_FLAGS_UVDSAFE 2 -#define ATOM_PPLIB_R600_FLAGS_BACKBIASENABLE 4 -#define ATOM_PPLIB_R600_FLAGS_MEMORY_ODT_OFF 8 -#define ATOM_PPLIB_R600_FLAGS_MEMORY_DLL_OFF 16 -#define ATOM_PPLIB_R600_FLAGS_LOWPOWER 32 // On the RV770 use 'low power' setting (sequencer S0). - -typedef struct _ATOM_PPLIB_EVERGREEN_CLOCK_INFO -{ - USHORT usEngineClockLow; - UCHAR ucEngineClockHigh; - - USHORT usMemoryClockLow; - UCHAR ucMemoryClockHigh; - - USHORT usVDDC; - USHORT usVDDCI; - USHORT usUnused; - - ULONG ulFlags; // ATOM_PPLIB_R600_FLAGS_* - -} ATOM_PPLIB_EVERGREEN_CLOCK_INFO; - -typedef struct _ATOM_PPLIB_SI_CLOCK_INFO -{ - USHORT usEngineClockLow; - UCHAR ucEngineClockHigh; - - USHORT usMemoryClockLow; - UCHAR ucMemoryClockHigh; - - USHORT usVDDC; - USHORT usVDDCI; - UCHAR ucPCIEGen; - UCHAR ucUnused1; - - ULONG ulFlags; // ATOM_PPLIB_SI_FLAGS_*, no flag is necessary for now - -} ATOM_PPLIB_SI_CLOCK_INFO; - - -typedef struct _ATOM_PPLIB_RS780_CLOCK_INFO - -{ - USHORT usLowEngineClockLow; // Low Engine clock in MHz (the same way as on the R600). - UCHAR ucLowEngineClockHigh; - USHORT usHighEngineClockLow; // High Engine clock in MHz. - UCHAR ucHighEngineClockHigh; - USHORT usMemoryClockLow; // For now one of the ATOM_PPLIB_RS780_SPMCLK_XXXX constants. - UCHAR ucMemoryClockHigh; // Currentyl unused. - UCHAR ucPadding; // For proper alignment and size. - USHORT usVDDC; // For the 780, use: None, Low, High, Variable - UCHAR ucMaxHTLinkWidth; // From SBIOS - {2, 4, 8, 16} - UCHAR ucMinHTLinkWidth; // From SBIOS - {2, 4, 8, 16}. Effective only if CDLW enabled. Minimum down stream width could be bigger as display BW requriement. - USHORT usHTLinkFreq; // See definition ATOM_PPLIB_RS780_HTLINKFREQ_xxx or in MHz(>=200). - ULONG ulFlags; -} ATOM_PPLIB_RS780_CLOCK_INFO; - -#define ATOM_PPLIB_RS780_VOLTAGE_NONE 0 -#define ATOM_PPLIB_RS780_VOLTAGE_LOW 1 -#define ATOM_PPLIB_RS780_VOLTAGE_HIGH 2 -#define ATOM_PPLIB_RS780_VOLTAGE_VARIABLE 3 - -#define ATOM_PPLIB_RS780_SPMCLK_NONE 0 // We cannot change the side port memory clock, leave it as it is. -#define ATOM_PPLIB_RS780_SPMCLK_LOW 1 -#define ATOM_PPLIB_RS780_SPMCLK_HIGH 2 - -#define ATOM_PPLIB_RS780_HTLINKFREQ_NONE 0 -#define ATOM_PPLIB_RS780_HTLINKFREQ_LOW 1 -#define ATOM_PPLIB_RS780_HTLINKFREQ_HIGH 2 - -typedef struct _ATOM_PPLIB_SUMO_CLOCK_INFO{ - USHORT usEngineClockLow; //clockfrequency & 0xFFFF. The unit is in 10khz - UCHAR ucEngineClockHigh; //clockfrequency >> 16. - UCHAR vddcIndex; //2-bit vddc index; - USHORT tdpLimit; - //please initalize to 0 - USHORT rsv1; - //please initialize to 0s - ULONG rsv2[2]; -}ATOM_PPLIB_SUMO_CLOCK_INFO; - - - -typedef struct _ATOM_PPLIB_STATE_V2 -{ - //number of valid dpm levels in this state; Driver uses it to calculate the whole - //size of the state: sizeof(ATOM_PPLIB_STATE_V2) + (ucNumDPMLevels - 1) * sizeof(UCHAR) - UCHAR ucNumDPMLevels; - - //a index to the array of nonClockInfos - UCHAR nonClockInfoIndex; - /** - * Driver will read the first ucNumDPMLevels in this array - */ - UCHAR clockInfoIndex[1]; -} ATOM_PPLIB_STATE_V2; - -typedef struct _StateArray{ - //how many states we have - UCHAR ucNumEntries; - - ATOM_PPLIB_STATE_V2 states[1]; -}StateArray; - - -typedef struct _ClockInfoArray{ - //how many clock levels we have - UCHAR ucNumEntries; - - //sizeof(ATOM_PPLIB_CLOCK_INFO) - UCHAR ucEntrySize; - - UCHAR clockInfo[1]; -}ClockInfoArray; - -typedef struct _NonClockInfoArray{ - - //how many non-clock levels we have. normally should be same as number of states - UCHAR ucNumEntries; - //sizeof(ATOM_PPLIB_NONCLOCK_INFO) - UCHAR ucEntrySize; - - ATOM_PPLIB_NONCLOCK_INFO nonClockInfo[1]; -}NonClockInfoArray; - -typedef struct _ATOM_PPLIB_Clock_Voltage_Dependency_Record -{ - USHORT usClockLow; - UCHAR ucClockHigh; - USHORT usVoltage; -}ATOM_PPLIB_Clock_Voltage_Dependency_Record; - -typedef struct _ATOM_PPLIB_Clock_Voltage_Dependency_Table -{ - UCHAR ucNumEntries; // Number of entries. - ATOM_PPLIB_Clock_Voltage_Dependency_Record entries[1]; // Dynamically allocate entries. -}ATOM_PPLIB_Clock_Voltage_Dependency_Table; - -typedef struct _ATOM_PPLIB_Clock_Voltage_Limit_Record -{ - USHORT usSclkLow; - UCHAR ucSclkHigh; - USHORT usMclkLow; - UCHAR ucMclkHigh; - USHORT usVddc; - USHORT usVddci; -}ATOM_PPLIB_Clock_Voltage_Limit_Record; - -typedef struct _ATOM_PPLIB_Clock_Voltage_Limit_Table -{ - UCHAR ucNumEntries; // Number of entries. - ATOM_PPLIB_Clock_Voltage_Limit_Record entries[1]; // Dynamically allocate entries. -}ATOM_PPLIB_Clock_Voltage_Limit_Table; - -typedef struct _ATOM_PPLIB_CAC_Leakage_Record -{ - USHORT usVddc; // We use this field for the "fake" standardized VDDC for power calculations - ULONG ulLeakageValue; -}ATOM_PPLIB_CAC_Leakage_Record; - -typedef struct _ATOM_PPLIB_CAC_Leakage_Table -{ - UCHAR ucNumEntries; // Number of entries. - ATOM_PPLIB_CAC_Leakage_Record entries[1]; // Dynamically allocate entries. -}ATOM_PPLIB_CAC_Leakage_Table; - -typedef struct _ATOM_PPLIB_PhaseSheddingLimits_Record -{ - USHORT usVoltage; - USHORT usSclkLow; - UCHAR ucSclkHigh; - USHORT usMclkLow; - UCHAR ucMclkHigh; -}ATOM_PPLIB_PhaseSheddingLimits_Record; - -typedef struct _ATOM_PPLIB_PhaseSheddingLimits_Table -{ - UCHAR ucNumEntries; // Number of entries. - ATOM_PPLIB_PhaseSheddingLimits_Record entries[1]; // Dynamically allocate entries. -}ATOM_PPLIB_PhaseSheddingLimits_Table; - -typedef struct _VCEClockInfo{ - USHORT usEVClkLow; - UCHAR ucEVClkHigh; - USHORT usECClkLow; - UCHAR ucECClkHigh; -}VCEClockInfo; - -typedef struct _VCEClockInfoArray{ - UCHAR ucNumEntries; - VCEClockInfo entries[1]; -}VCEClockInfoArray; - -typedef struct _ATOM_PPLIB_VCE_Clock_Voltage_Limit_Record -{ - USHORT usVoltage; - UCHAR ucVCEClockInfoIndex; -}ATOM_PPLIB_VCE_Clock_Voltage_Limit_Record; - -typedef struct _ATOM_PPLIB_VCE_Clock_Voltage_Limit_Table -{ - UCHAR numEntries; - ATOM_PPLIB_VCE_Clock_Voltage_Limit_Record entries[1]; -}ATOM_PPLIB_VCE_Clock_Voltage_Limit_Table; - -typedef struct _ATOM_PPLIB_VCE_State_Record -{ - UCHAR ucVCEClockInfoIndex; - UCHAR ucClockInfoIndex; //highest 2 bits indicates memory p-states, lower 6bits indicates index to ClockInfoArrary -}ATOM_PPLIB_VCE_State_Record; - -typedef struct _ATOM_PPLIB_VCE_State_Table -{ - UCHAR numEntries; - ATOM_PPLIB_VCE_State_Record entries[1]; -}ATOM_PPLIB_VCE_State_Table; - - -typedef struct _ATOM_PPLIB_VCE_Table -{ - UCHAR revid; -// VCEClockInfoArray array; -// ATOM_PPLIB_VCE_Clock_Voltage_Limit_Table limits; -// ATOM_PPLIB_VCE_State_Table states; -}ATOM_PPLIB_VCE_Table; - - -typedef struct _UVDClockInfo{ - USHORT usVClkLow; - UCHAR ucVClkHigh; - USHORT usDClkLow; - UCHAR ucDClkHigh; -}UVDClockInfo; - -typedef struct _UVDClockInfoArray{ - UCHAR ucNumEntries; - UVDClockInfo entries[1]; -}UVDClockInfoArray; - -typedef struct _ATOM_PPLIB_UVD_Clock_Voltage_Limit_Record -{ - USHORT usVoltage; - UCHAR ucUVDClockInfoIndex; -}ATOM_PPLIB_UVD_Clock_Voltage_Limit_Record; - -typedef struct _ATOM_PPLIB_UVD_Clock_Voltage_Limit_Table -{ - UCHAR numEntries; - ATOM_PPLIB_UVD_Clock_Voltage_Limit_Record entries[1]; -}ATOM_PPLIB_UVD_Clock_Voltage_Limit_Table; - -typedef struct _ATOM_PPLIB_UVD_State_Record -{ - UCHAR ucUVDClockInfoIndex; - UCHAR ucClockInfoIndex; //highest 2 bits indicates memory p-states, lower 6bits indicates index to ClockInfoArrary -}ATOM_PPLIB_UVD_State_Record; - -typedef struct _ATOM_PPLIB_UVD_State_Table -{ - UCHAR numEntries; - ATOM_PPLIB_UVD_State_Record entries[1]; -}ATOM_PPLIB_UVD_State_Table; - - -typedef struct _ATOM_PPLIB_UVD_Table -{ - UCHAR revid; -// UVDClockInfoArray array; -// ATOM_PPLIB_UVD_Clock_Voltage_Limit_Table limits; -// ATOM_PPLIB_UVD_State_Table states; -}ATOM_PPLIB_UVD_Table; - -/**************************************************************************/ - // Following definitions are for compatibility issue in different SW components. #define ATOM_MASTER_DATA_TABLE_REVISION 0x01 @@ -7978,8 +7944,8 @@ typedef struct { AMD_ACPI_DESCRIPTION_HEADER SHeader; UCHAR TableUUID[16]; //0x24 - ULONG VBIOSImageOffset; //0x34. Offset to the first GOP_VBIOS_CONTENT block from the beginning of the stucture. - ULONG Lib1ImageOffset; //0x38. Offset to the first GOP_LIB1_CONTENT block from the beginning of the stucture. + ULONG VBIOSImageOffset; //0x34. Offset to the first GOP_VBIOS_CONTENT block from the beginning of the structure. + ULONG Lib1ImageOffset; //0x38. Offset to the first GOP_LIB1_CONTENT block from the beginning of the structure. ULONG Reserved[4]; //0x3C }UEFI_ACPI_VFCT; @@ -8010,3 +7976,6 @@ #endif /* _ATOMBIOS_H */ + +#include "pptable.h" +