--- zzzz-none-000/linux-3.10.107/drivers/net/ethernet/realtek/atp.h 2017-06-27 09:49:32.000000000 +0000 +++ scorpion-7490-727/linux-3.10.107/drivers/net/ethernet/realtek/atp.h 2021-02-04 17:41:59.000000000 +0000 @@ -6,10 +6,10 @@ /* The header prepended to received packets. */ struct rx_header { - ushort pad; /* Pad. */ - ushort rx_count; - ushort rx_status; /* Unknown bit assignments :-<. */ - ushort cur_addr; /* Apparently the current buffer address(?) */ + ushort pad; /* Pad. */ + ushort rx_count; + ushort rx_status; /* Unknown bit assignments :-<. */ + ushort cur_addr; /* Apparently the current buffer address(?) */ }; #define PAR_DATA 0 @@ -29,22 +29,25 @@ #define RdAddr 0xC0 #define HNib 0x10 -enum page0_regs -{ - /* The first six registers hold the ethernet physical station address. */ - PAR0 = 0, PAR1 = 1, PAR2 = 2, PAR3 = 3, PAR4 = 4, PAR5 = 5, - TxCNT0 = 6, TxCNT1 = 7, /* The transmit byte count. */ - TxSTAT = 8, RxSTAT = 9, /* Tx and Rx status. */ - ISR = 10, IMR = 11, /* Interrupt status and mask. */ - CMR1 = 12, /* Command register 1. */ - CMR2 = 13, /* Command register 2. */ - MODSEL = 14, /* Mode select register. */ - MAR = 14, /* Memory address register (?). */ - CMR2_h = 0x1d, }; - -enum eepage_regs -{ PROM_CMD = 6, PROM_DATA = 7 }; /* Note that PROM_CMD is in the "high" bits. */ +enum page0_regs { + /* The first six registers hold + * the ethernet physical station address. + */ + PAR0 = 0, PAR1 = 1, PAR2 = 2, PAR3 = 3, PAR4 = 4, PAR5 = 5, + TxCNT0 = 6, TxCNT1 = 7, /* The transmit byte count. */ + TxSTAT = 8, RxSTAT = 9, /* Tx and Rx status. */ + ISR = 10, IMR = 11, /* Interrupt status and mask. */ + CMR1 = 12, /* Command register 1. */ + CMR2 = 13, /* Command register 2. */ + MODSEL = 14, /* Mode select register. */ + MAR = 14, /* Memory address register (?). */ + CMR2_h = 0x1d, +}; +enum eepage_regs { + PROM_CMD = 6, + PROM_DATA = 7 /* Note that PROM_CMD is in the "high" bits. */ +}; #define ISR_TxOK 0x01 #define ISR_RxOK 0x04 @@ -72,141 +75,146 @@ #define CMR2h_Normal 2 /* Accept physical and broadcast address. */ #define CMR2h_PROMISC 3 /* Promiscuous mode. */ -/* An inline function used below: it differs from inb() by explicitly return an unsigned - char, saving a truncation. */ +/* An inline function used below: it differs from inb() by explicitly + * return an unsigned char, saving a truncation. + */ static inline unsigned char inbyte(unsigned short port) { - unsigned char _v; - __asm__ __volatile__ ("inb %w1,%b0" :"=a" (_v):"d" (port)); - return _v; + unsigned char _v; + + __asm__ __volatile__ ("inb %w1,%b0" : "=a" (_v) : "d" (port)); + return _v; } /* Read register OFFSET. - This command should always be terminated with read_end(). */ + * This command should always be terminated with read_end(). + */ static inline unsigned char read_nibble(short port, unsigned char offset) { - unsigned char retval; - outb(EOC+offset, port + PAR_DATA); - outb(RdAddr+offset, port + PAR_DATA); - inbyte(port + PAR_STATUS); /* Settling time delay */ - retval = inbyte(port + PAR_STATUS); - outb(EOC+offset, port + PAR_DATA); + unsigned char retval; + + outb(EOC+offset, port + PAR_DATA); + outb(RdAddr+offset, port + PAR_DATA); + inbyte(port + PAR_STATUS); /* Settling time delay */ + retval = inbyte(port + PAR_STATUS); + outb(EOC+offset, port + PAR_DATA); - return retval; + return retval; } /* Functions for bulk data read. The interrupt line is always disabled. */ /* Get a byte using read mode 0, reading data from the control lines. */ static inline unsigned char read_byte_mode0(short ioaddr) { - unsigned char low_nib; + unsigned char low_nib; - outb(Ctrl_LNibRead, ioaddr + PAR_CONTROL); - inbyte(ioaddr + PAR_STATUS); - low_nib = (inbyte(ioaddr + PAR_STATUS) >> 3) & 0x0f; - outb(Ctrl_HNibRead, ioaddr + PAR_CONTROL); - inbyte(ioaddr + PAR_STATUS); /* Settling time delay -- needed! */ - inbyte(ioaddr + PAR_STATUS); /* Settling time delay -- needed! */ - return low_nib | ((inbyte(ioaddr + PAR_STATUS) << 1) & 0xf0); + outb(Ctrl_LNibRead, ioaddr + PAR_CONTROL); + inbyte(ioaddr + PAR_STATUS); + low_nib = (inbyte(ioaddr + PAR_STATUS) >> 3) & 0x0f; + outb(Ctrl_HNibRead, ioaddr + PAR_CONTROL); + inbyte(ioaddr + PAR_STATUS); /* Settling time delay -- needed! */ + inbyte(ioaddr + PAR_STATUS); /* Settling time delay -- needed! */ + return low_nib | ((inbyte(ioaddr + PAR_STATUS) << 1) & 0xf0); } /* The same as read_byte_mode0(), but does multiple inb()s for stability. */ static inline unsigned char read_byte_mode2(short ioaddr) { - unsigned char low_nib; + unsigned char low_nib; - outb(Ctrl_LNibRead, ioaddr + PAR_CONTROL); - inbyte(ioaddr + PAR_STATUS); - low_nib = (inbyte(ioaddr + PAR_STATUS) >> 3) & 0x0f; - outb(Ctrl_HNibRead, ioaddr + PAR_CONTROL); - inbyte(ioaddr + PAR_STATUS); /* Settling time delay -- needed! */ - return low_nib | ((inbyte(ioaddr + PAR_STATUS) << 1) & 0xf0); + outb(Ctrl_LNibRead, ioaddr + PAR_CONTROL); + inbyte(ioaddr + PAR_STATUS); + low_nib = (inbyte(ioaddr + PAR_STATUS) >> 3) & 0x0f; + outb(Ctrl_HNibRead, ioaddr + PAR_CONTROL); + inbyte(ioaddr + PAR_STATUS); /* Settling time delay -- needed! */ + return low_nib | ((inbyte(ioaddr + PAR_STATUS) << 1) & 0xf0); } /* Read a byte through the data register. */ static inline unsigned char read_byte_mode4(short ioaddr) { - unsigned char low_nib; + unsigned char low_nib; - outb(RdAddr | MAR, ioaddr + PAR_DATA); - low_nib = (inbyte(ioaddr + PAR_STATUS) >> 3) & 0x0f; - outb(RdAddr | HNib | MAR, ioaddr + PAR_DATA); - return low_nib | ((inbyte(ioaddr + PAR_STATUS) << 1) & 0xf0); + outb(RdAddr | MAR, ioaddr + PAR_DATA); + low_nib = (inbyte(ioaddr + PAR_STATUS) >> 3) & 0x0f; + outb(RdAddr | HNib | MAR, ioaddr + PAR_DATA); + return low_nib | ((inbyte(ioaddr + PAR_STATUS) << 1) & 0xf0); } /* Read a byte through the data register, double reading to allow settling. */ static inline unsigned char read_byte_mode6(short ioaddr) { - unsigned char low_nib; + unsigned char low_nib; - outb(RdAddr | MAR, ioaddr + PAR_DATA); - inbyte(ioaddr + PAR_STATUS); - low_nib = (inbyte(ioaddr + PAR_STATUS) >> 3) & 0x0f; - outb(RdAddr | HNib | MAR, ioaddr + PAR_DATA); - inbyte(ioaddr + PAR_STATUS); - return low_nib | ((inbyte(ioaddr + PAR_STATUS) << 1) & 0xf0); + outb(RdAddr | MAR, ioaddr + PAR_DATA); + inbyte(ioaddr + PAR_STATUS); + low_nib = (inbyte(ioaddr + PAR_STATUS) >> 3) & 0x0f; + outb(RdAddr | HNib | MAR, ioaddr + PAR_DATA); + inbyte(ioaddr + PAR_STATUS); + return low_nib | ((inbyte(ioaddr + PAR_STATUS) << 1) & 0xf0); } static inline void write_reg(short port, unsigned char reg, unsigned char value) { - unsigned char outval; - outb(EOC | reg, port + PAR_DATA); - outval = WrAddr | reg; - outb(outval, port + PAR_DATA); - outb(outval, port + PAR_DATA); /* Double write for PS/2. */ - - outval &= 0xf0; - outval |= value; - outb(outval, port + PAR_DATA); - outval &= 0x1f; - outb(outval, port + PAR_DATA); - outb(outval, port + PAR_DATA); + unsigned char outval; + + outb(EOC | reg, port + PAR_DATA); + outval = WrAddr | reg; + outb(outval, port + PAR_DATA); + outb(outval, port + PAR_DATA); /* Double write for PS/2. */ + + outval &= 0xf0; + outval |= value; + outb(outval, port + PAR_DATA); + outval &= 0x1f; + outb(outval, port + PAR_DATA); + outb(outval, port + PAR_DATA); - outb(EOC | outval, port + PAR_DATA); + outb(EOC | outval, port + PAR_DATA); } static inline void write_reg_high(short port, unsigned char reg, unsigned char value) { - unsigned char outval = EOC | HNib | reg; + unsigned char outval = EOC | HNib | reg; - outb(outval, port + PAR_DATA); - outval &= WrAddr | HNib | 0x0f; - outb(outval, port + PAR_DATA); - outb(outval, port + PAR_DATA); /* Double write for PS/2. */ - - outval = WrAddr | HNib | value; - outb(outval, port + PAR_DATA); - outval &= HNib | 0x0f; /* HNib | value */ - outb(outval, port + PAR_DATA); - outb(outval, port + PAR_DATA); + outb(outval, port + PAR_DATA); + outval &= WrAddr | HNib | 0x0f; + outb(outval, port + PAR_DATA); + outb(outval, port + PAR_DATA); /* Double write for PS/2. */ + + outval = WrAddr | HNib | value; + outb(outval, port + PAR_DATA); + outval &= HNib | 0x0f; /* HNib | value */ + outb(outval, port + PAR_DATA); + outb(outval, port + PAR_DATA); - outb(EOC | HNib | outval, port + PAR_DATA); + outb(EOC | HNib | outval, port + PAR_DATA); } /* Write a byte out using nibble mode. The low nibble is written first. */ static inline void write_reg_byte(short port, unsigned char reg, unsigned char value) { - unsigned char outval; - outb(EOC | reg, port + PAR_DATA); /* Reset the address register. */ - outval = WrAddr | reg; - outb(outval, port + PAR_DATA); - outb(outval, port + PAR_DATA); /* Double write for PS/2. */ - - outb((outval & 0xf0) | (value & 0x0f), port + PAR_DATA); - outb(value & 0x0f, port + PAR_DATA); - value >>= 4; - outb(value, port + PAR_DATA); - outb(0x10 | value, port + PAR_DATA); - outb(0x10 | value, port + PAR_DATA); + unsigned char outval; + + outb(EOC | reg, port + PAR_DATA); /* Reset the address register. */ + outval = WrAddr | reg; + outb(outval, port + PAR_DATA); + outb(outval, port + PAR_DATA); /* Double write for PS/2. */ + + outb((outval & 0xf0) | (value & 0x0f), port + PAR_DATA); + outb(value & 0x0f, port + PAR_DATA); + value >>= 4; + outb(value, port + PAR_DATA); + outb(0x10 | value, port + PAR_DATA); + outb(0x10 | value, port + PAR_DATA); - outb(EOC | value, port + PAR_DATA); /* Reset the address register. */ + outb(EOC | value, port + PAR_DATA); /* Reset the address register. */ } -/* - * Bulk data writes to the packet buffer. The interrupt line remains enabled. +/* Bulk data writes to the packet buffer. The interrupt line remains enabled. * The first, faster method uses only the dataport (data modes 0, 2 & 4). * The second (backup) method uses data and control regs (modes 1, 3 & 5). * It should only be needed when there is skew between the individual data @@ -214,28 +222,28 @@ */ static inline void write_byte_mode0(short ioaddr, unsigned char value) { - outb(value & 0x0f, ioaddr + PAR_DATA); - outb((value>>4) | 0x10, ioaddr + PAR_DATA); + outb(value & 0x0f, ioaddr + PAR_DATA); + outb((value>>4) | 0x10, ioaddr + PAR_DATA); } static inline void write_byte_mode1(short ioaddr, unsigned char value) { - outb(value & 0x0f, ioaddr + PAR_DATA); - outb(Ctrl_IRQEN | Ctrl_LNibWrite, ioaddr + PAR_CONTROL); - outb((value>>4) | 0x10, ioaddr + PAR_DATA); - outb(Ctrl_IRQEN | Ctrl_HNibWrite, ioaddr + PAR_CONTROL); + outb(value & 0x0f, ioaddr + PAR_DATA); + outb(Ctrl_IRQEN | Ctrl_LNibWrite, ioaddr + PAR_CONTROL); + outb((value>>4) | 0x10, ioaddr + PAR_DATA); + outb(Ctrl_IRQEN | Ctrl_HNibWrite, ioaddr + PAR_CONTROL); } /* Write 16bit VALUE to the packet buffer: the same as above just doubled. */ static inline void write_word_mode0(short ioaddr, unsigned short value) { - outb(value & 0x0f, ioaddr + PAR_DATA); - value >>= 4; - outb((value & 0x0f) | 0x10, ioaddr + PAR_DATA); - value >>= 4; - outb(value & 0x0f, ioaddr + PAR_DATA); - value >>= 4; - outb((value & 0x0f) | 0x10, ioaddr + PAR_DATA); + outb(value & 0x0f, ioaddr + PAR_DATA); + value >>= 4; + outb((value & 0x0f) | 0x10, ioaddr + PAR_DATA); + value >>= 4; + outb(value & 0x0f, ioaddr + PAR_DATA); + value >>= 4; + outb((value & 0x0f) | 0x10, ioaddr + PAR_DATA); } /* EEPROM_Ctrl bits. */ @@ -248,10 +256,10 @@ /* Delay between EEPROM clock transitions. */ #define eeprom_delay(ticks) \ -do { int _i = 40; while (--_i > 0) { __SLOW_DOWN_IO; }} while (0) +do { int _i = 40; while (--_i > 0) { __SLOW_DOWN_IO; } } while (0) /* The EEPROM commands include the alway-set leading bit. */ #define EE_WRITE_CMD(offset) (((5 << 6) + (offset)) << 17) -#define EE_READ(offset) (((6 << 6) + (offset)) << 17) +#define EE_READ(offset) (((6 << 6) + (offset)) << 17) #define EE_ERASE(offset) (((7 << 6) + (offset)) << 17) #define EE_CMD_SIZE 27 /* The command+address+data size. */