--- zzzz-none-000/linux-3.10.107/drivers/net/ethernet/ti/Kconfig	2017-06-27 09:49:32.000000000 +0000
+++ scorpion-7490-727/linux-3.10.107/drivers/net/ethernet/ti/Kconfig	2021-02-04 17:41:59.000000000 +0000
@@ -5,11 +5,9 @@
 config NET_VENDOR_TI
 	bool "Texas Instruments (TI) devices"
 	default y
-	depends on PCI || EISA || AR7 || (ARM && (ARCH_DAVINCI || ARCH_OMAP3 || SOC_AM33XX))
+	depends on PCI || EISA || AR7 || ARCH_DAVINCI || ARCH_OMAP2PLUS || ARCH_KEYSTONE
 	---help---
-	  If you have a network (Ethernet) card belonging to this class, say Y
-	  and read the Ethernet-HOWTO, available from
-	  <http://www.tldp.org/docs.html#howto>.
+	  If you have a network (Ethernet) card belonging to this class, say Y.
 
 	  Note that the answer to this question doesn't directly affect the
 	  kernel: saying N will just cause the configurator to skip all
@@ -32,7 +30,7 @@
 
 config TI_DAVINCI_MDIO
 	tristate "TI DaVinci MDIO Support"
-	depends on ARM && ( ARCH_DAVINCI || ARCH_OMAP3 || SOC_AM33XX )
+	depends on ARCH_DAVINCI || ARCH_OMAP2PLUS || ARCH_KEYSTONE
 	select PHYLIB
 	---help---
 	  This driver supports TI's DaVinci MDIO module.
@@ -42,18 +40,34 @@
 
 config TI_DAVINCI_CPDMA
 	tristate "TI DaVinci CPDMA Support"
-	depends on ARM && ( ARCH_DAVINCI || ARCH_OMAP3 || SOC_AM33XX )
+	depends on ARCH_DAVINCI || ARCH_OMAP2PLUS
 	---help---
 	  This driver supports TI's DaVinci CPDMA dma engine.
 
 	  To compile this driver as a module, choose M here: the module
 	  will be called davinci_cpdma.  This is recommended.
 
+config TI_CPSW_PHY_SEL
+	bool "TI CPSW Switch Phy sel Support"
+	depends on TI_CPSW
+	---help---
+	  This driver supports configuring of the phy mode connected to
+	  the CPSW.
+
+config TI_CPSW_ALE
+	tristate "TI CPSW ALE Support"
+	---help---
+	  This driver supports TI's CPSW ALE module.
+
 config TI_CPSW
 	tristate "TI CPSW Switch Support"
-	depends on ARM && (ARCH_DAVINCI || SOC_AM33XX)
+	depends on ARCH_DAVINCI || ARCH_OMAP2PLUS
 	select TI_DAVINCI_CPDMA
 	select TI_DAVINCI_MDIO
+	select TI_CPSW_PHY_SEL
+	select TI_CPSW_ALE
+	select MFD_SYSCON
+	select REGMAP
 	---help---
 	  This driver supports TI's CPSW Ethernet Switch.
 
@@ -61,7 +75,7 @@
 	  will be called cpsw.
 
 config TI_CPTS
-	boolean "TI Common Platform Time Sync (CPTS) Support"
+	bool "TI Common Platform Time Sync (CPTS) Support"
 	depends on TI_CPSW
 	select PTP_1588_CLOCK
 	---help---
@@ -69,14 +83,32 @@
 	  the CPSW Ethernet Switch. The unit can time stamp PTP UDP/IPv4
 	  and Layer 2 packets, and the driver offers a PTP Hardware Clock.
 
+config TI_KEYSTONE_NETCP
+	tristate "TI Keystone NETCP Core Support"
+	select TI_CPSW_ALE
+	select TI_DAVINCI_MDIO
+	depends on OF
+	depends on KEYSTONE_NAVIGATOR_DMA && KEYSTONE_NAVIGATOR_QMSS
+	---help---
+	  This driver supports TI's Keystone NETCP Core.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called keystone_netcp.
+
+config TI_KEYSTONE_NETCP_ETHSS
+	depends on TI_KEYSTONE_NETCP
+	tristate "TI Keystone NETCP Ethernet subsystem Support"
+	---help---
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called keystone_netcp_ethss.
+
 config TLAN
 	tristate "TI ThunderLAN support"
 	depends on (PCI || EISA)
 	---help---
 	  If you have a PCI Ethernet network card based on the ThunderLAN chip
-	  which is supported by this driver, say Y and read the
-	  Ethernet-HOWTO, available from
-	  <http://www.tldp.org/docs.html#howto>.
+	  which is supported by this driver, say Y here.
 
 	  Devices currently supported by this driver are Compaq Netelligent,
 	  Compaq NetFlex and Olicom cards.  Please read the file