--- zzzz-none-000/linux-3.10.107/drivers/net/ieee802154/mrf24j40.c 2017-06-27 09:49:32.000000000 +0000 +++ scorpion-7490-727/linux-3.10.107/drivers/net/ieee802154/mrf24j40.c 2021-02-04 17:41:59.000000000 +0000 @@ -13,58 +13,177 @@ * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. */ #include #include #include -#include -#include +#include +#include +#include +#include #include -#include /* MRF24J40 Short Address Registers */ -#define REG_RXMCR 0x00 /* Receive MAC control */ -#define REG_PANIDL 0x01 /* PAN ID (low) */ -#define REG_PANIDH 0x02 /* PAN ID (high) */ -#define REG_SADRL 0x03 /* Short address (low) */ -#define REG_SADRH 0x04 /* Short address (high) */ -#define REG_EADR0 0x05 /* Long address (low) (high is EADR7) */ -#define REG_TXMCR 0x11 /* Transmit MAC control */ -#define REG_PACON0 0x16 /* Power Amplifier Control */ -#define REG_PACON1 0x17 /* Power Amplifier Control */ -#define REG_PACON2 0x18 /* Power Amplifier Control */ -#define REG_TXNCON 0x1B /* Transmit Normal FIFO Control */ -#define REG_TXSTAT 0x24 /* TX MAC Status Register */ -#define REG_SOFTRST 0x2A /* Soft Reset */ -#define REG_TXSTBL 0x2E /* TX Stabilization */ -#define REG_INTSTAT 0x31 /* Interrupt Status */ -#define REG_INTCON 0x32 /* Interrupt Control */ -#define REG_RFCTL 0x36 /* RF Control Mode Register */ -#define REG_BBREG1 0x39 /* Baseband Registers */ -#define REG_BBREG2 0x3A /* */ -#define REG_BBREG6 0x3E /* */ -#define REG_CCAEDTH 0x3F /* Energy Detection Threshold */ +#define REG_RXMCR 0x00 /* Receive MAC control */ +#define BIT_PROMI BIT(0) +#define BIT_ERRPKT BIT(1) +#define BIT_NOACKRSP BIT(5) +#define BIT_PANCOORD BIT(3) + +#define REG_PANIDL 0x01 /* PAN ID (low) */ +#define REG_PANIDH 0x02 /* PAN ID (high) */ +#define REG_SADRL 0x03 /* Short address (low) */ +#define REG_SADRH 0x04 /* Short address (high) */ +#define REG_EADR0 0x05 /* Long address (low) (high is EADR7) */ +#define REG_EADR1 0x06 +#define REG_EADR2 0x07 +#define REG_EADR3 0x08 +#define REG_EADR4 0x09 +#define REG_EADR5 0x0A +#define REG_EADR6 0x0B +#define REG_EADR7 0x0C +#define REG_RXFLUSH 0x0D +#define REG_ORDER 0x10 +#define REG_TXMCR 0x11 /* Transmit MAC control */ +#define TXMCR_MIN_BE_SHIFT 3 +#define TXMCR_MIN_BE_MASK 0x18 +#define TXMCR_CSMA_RETRIES_SHIFT 0 +#define TXMCR_CSMA_RETRIES_MASK 0x07 + +#define REG_ACKTMOUT 0x12 +#define REG_ESLOTG1 0x13 +#define REG_SYMTICKL 0x14 +#define REG_SYMTICKH 0x15 +#define REG_PACON0 0x16 /* Power Amplifier Control */ +#define REG_PACON1 0x17 /* Power Amplifier Control */ +#define REG_PACON2 0x18 /* Power Amplifier Control */ +#define REG_TXBCON0 0x1A +#define REG_TXNCON 0x1B /* Transmit Normal FIFO Control */ +#define BIT_TXNTRIG BIT(0) +#define BIT_TXNACKREQ BIT(2) + +#define REG_TXG1CON 0x1C +#define REG_TXG2CON 0x1D +#define REG_ESLOTG23 0x1E +#define REG_ESLOTG45 0x1F +#define REG_ESLOTG67 0x20 +#define REG_TXPEND 0x21 +#define REG_WAKECON 0x22 +#define REG_FROMOFFSET 0x23 +#define REG_TXSTAT 0x24 /* TX MAC Status Register */ +#define REG_TXBCON1 0x25 +#define REG_GATECLK 0x26 +#define REG_TXTIME 0x27 +#define REG_HSYMTMRL 0x28 +#define REG_HSYMTMRH 0x29 +#define REG_SOFTRST 0x2A /* Soft Reset */ +#define REG_SECCON0 0x2C +#define REG_SECCON1 0x2D +#define REG_TXSTBL 0x2E /* TX Stabilization */ +#define REG_RXSR 0x30 +#define REG_INTSTAT 0x31 /* Interrupt Status */ +#define BIT_TXNIF BIT(0) +#define BIT_RXIF BIT(3) + +#define REG_INTCON 0x32 /* Interrupt Control */ +#define BIT_TXNIE BIT(0) +#define BIT_RXIE BIT(3) + +#define REG_GPIO 0x33 /* GPIO */ +#define REG_TRISGPIO 0x34 /* GPIO direction */ +#define REG_SLPACK 0x35 +#define REG_RFCTL 0x36 /* RF Control Mode Register */ +#define BIT_RFRST BIT(2) + +#define REG_SECCR2 0x37 +#define REG_BBREG0 0x38 +#define REG_BBREG1 0x39 /* Baseband Registers */ +#define BIT_RXDECINV BIT(2) + +#define REG_BBREG2 0x3A /* */ +#define BBREG2_CCA_MODE_SHIFT 6 +#define BBREG2_CCA_MODE_MASK 0xc0 + +#define REG_BBREG3 0x3B +#define REG_BBREG4 0x3C +#define REG_BBREG6 0x3E /* */ +#define REG_CCAEDTH 0x3F /* Energy Detection Threshold */ /* MRF24J40 Long Address Registers */ -#define REG_RFCON0 0x200 /* RF Control Registers */ -#define REG_RFCON1 0x201 -#define REG_RFCON2 0x202 -#define REG_RFCON3 0x203 -#define REG_RFCON5 0x205 -#define REG_RFCON6 0x206 -#define REG_RFCON7 0x207 -#define REG_RFCON8 0x208 -#define REG_RSSI 0x210 -#define REG_SLPCON0 0x211 /* Sleep Clock Control Registers */ -#define REG_SLPCON1 0x220 -#define REG_WAKETIMEL 0x222 /* Wake-up Time Match Value Low */ -#define REG_WAKETIMEH 0x223 /* Wake-up Time Match Value High */ -#define REG_RX_FIFO 0x300 /* Receive FIFO */ +#define REG_RFCON0 0x200 /* RF Control Registers */ +#define RFCON0_CH_SHIFT 4 +#define RFCON0_CH_MASK 0xf0 +#define RFOPT_RECOMMEND 3 + +#define REG_RFCON1 0x201 +#define REG_RFCON2 0x202 +#define REG_RFCON3 0x203 + +#define TXPWRL_MASK 0xc0 +#define TXPWRL_SHIFT 6 +#define TXPWRL_30 0x3 +#define TXPWRL_20 0x2 +#define TXPWRL_10 0x1 +#define TXPWRL_0 0x0 + +#define TXPWRS_MASK 0x38 +#define TXPWRS_SHIFT 3 +#define TXPWRS_6_3 0x7 +#define TXPWRS_4_9 0x6 +#define TXPWRS_3_7 0x5 +#define TXPWRS_2_8 0x4 +#define TXPWRS_1_9 0x3 +#define TXPWRS_1_2 0x2 +#define TXPWRS_0_5 0x1 +#define TXPWRS_0 0x0 + +#define REG_RFCON5 0x205 +#define REG_RFCON6 0x206 +#define REG_RFCON7 0x207 +#define REG_RFCON8 0x208 +#define REG_SLPCAL0 0x209 +#define REG_SLPCAL1 0x20A +#define REG_SLPCAL2 0x20B +#define REG_RFSTATE 0x20F +#define REG_RSSI 0x210 +#define REG_SLPCON0 0x211 /* Sleep Clock Control Registers */ +#define BIT_INTEDGE BIT(1) + +#define REG_SLPCON1 0x220 +#define REG_WAKETIMEL 0x222 /* Wake-up Time Match Value Low */ +#define REG_WAKETIMEH 0x223 /* Wake-up Time Match Value High */ +#define REG_REMCNTL 0x224 +#define REG_REMCNTH 0x225 +#define REG_MAINCNT0 0x226 +#define REG_MAINCNT1 0x227 +#define REG_MAINCNT2 0x228 +#define REG_MAINCNT3 0x229 +#define REG_TESTMODE 0x22F /* Test mode */ +#define REG_ASSOEAR0 0x230 +#define REG_ASSOEAR1 0x231 +#define REG_ASSOEAR2 0x232 +#define REG_ASSOEAR3 0x233 +#define REG_ASSOEAR4 0x234 +#define REG_ASSOEAR5 0x235 +#define REG_ASSOEAR6 0x236 +#define REG_ASSOEAR7 0x237 +#define REG_ASSOSAR0 0x238 +#define REG_ASSOSAR1 0x239 +#define REG_UNONCE0 0x240 +#define REG_UNONCE1 0x241 +#define REG_UNONCE2 0x242 +#define REG_UNONCE3 0x243 +#define REG_UNONCE4 0x244 +#define REG_UNONCE5 0x245 +#define REG_UNONCE6 0x246 +#define REG_UNONCE7 0x247 +#define REG_UNONCE8 0x248 +#define REG_UNONCE9 0x249 +#define REG_UNONCE10 0x24A +#define REG_UNONCE11 0x24B +#define REG_UNONCE12 0x24C +#define REG_RX_FIFO 0x300 /* Receive FIFO */ /* Device configuration: Only channels 11-26 on page 0 are supported. */ #define MRF24J40_CHAN_MIN 11 @@ -76,17 +195,59 @@ #define RX_FIFO_SIZE 144 /* From datasheet */ #define SET_CHANNEL_DELAY_US 192 /* From datasheet */ +enum mrf24j40_modules { MRF24J40, MRF24J40MA, MRF24J40MC }; + /* Device Private Data */ struct mrf24j40 { struct spi_device *spi; - struct ieee802154_dev *dev; + struct ieee802154_hw *hw; + + struct regmap *regmap_short; + struct regmap *regmap_long; - struct mutex buffer_mutex; /* only used to protect buf */ - struct completion tx_complete; - struct work_struct irqwork; - u8 *buf; /* 3 bytes. Used for SPI single-register transfers. */ + /* for writing txfifo */ + struct spi_message tx_msg; + u8 tx_hdr_buf[2]; + struct spi_transfer tx_hdr_trx; + u8 tx_len_buf[2]; + struct spi_transfer tx_len_trx; + struct spi_transfer tx_buf_trx; + struct sk_buff *tx_skb; + + /* post transmit message to send frame out */ + struct spi_message tx_post_msg; + u8 tx_post_buf[2]; + struct spi_transfer tx_post_trx; + + /* for protect/unprotect/read length rxfifo */ + struct spi_message rx_msg; + u8 rx_buf[3]; + struct spi_transfer rx_trx; + + /* receive handling */ + struct spi_message rx_buf_msg; + u8 rx_addr_buf[2]; + struct spi_transfer rx_addr_trx; + u8 rx_lqi_buf[2]; + struct spi_transfer rx_lqi_trx; + u8 rx_fifo_buf[RX_FIFO_SIZE]; + struct spi_transfer rx_fifo_buf_trx; + + /* isr handling for reading intstat */ + struct spi_message irq_msg; + u8 irq_buf[2]; + struct spi_transfer irq_trx; }; +/* regmap information for short address register access */ +#define MRF24J40_SHORT_WRITE 0x01 +#define MRF24J40_SHORT_READ 0x00 +#define MRF24J40_SHORT_NUMREGS 0x3F + +/* regmap information for long address register access */ +#define MRF24J40_LONG_ACCESS 0x80 +#define MRF24J40_LONG_NUMREGS 0x38F + /* Read/Write SPI Commands for Short and Long Address registers. */ #define MRF24J40_READSHORT(reg) ((reg) << 1) #define MRF24J40_WRITESHORT(reg) ((reg) << 1 | 1) @@ -98,118 +259,304 @@ #define printdev(X) (&X->spi->dev) -static int write_short_reg(struct mrf24j40 *devrec, u8 reg, u8 value) +static bool +mrf24j40_short_reg_writeable(struct device *dev, unsigned int reg) { - int ret; - struct spi_message msg; - struct spi_transfer xfer = { - .len = 2, - .tx_buf = devrec->buf, - .rx_buf = devrec->buf, - }; - - spi_message_init(&msg); - spi_message_add_tail(&xfer, &msg); - - mutex_lock(&devrec->buffer_mutex); - devrec->buf[0] = MRF24J40_WRITESHORT(reg); - devrec->buf[1] = value; + switch (reg) { + case REG_RXMCR: + case REG_PANIDL: + case REG_PANIDH: + case REG_SADRL: + case REG_SADRH: + case REG_EADR0: + case REG_EADR1: + case REG_EADR2: + case REG_EADR3: + case REG_EADR4: + case REG_EADR5: + case REG_EADR6: + case REG_EADR7: + case REG_RXFLUSH: + case REG_ORDER: + case REG_TXMCR: + case REG_ACKTMOUT: + case REG_ESLOTG1: + case REG_SYMTICKL: + case REG_SYMTICKH: + case REG_PACON0: + case REG_PACON1: + case REG_PACON2: + case REG_TXBCON0: + case REG_TXNCON: + case REG_TXG1CON: + case REG_TXG2CON: + case REG_ESLOTG23: + case REG_ESLOTG45: + case REG_ESLOTG67: + case REG_TXPEND: + case REG_WAKECON: + case REG_FROMOFFSET: + case REG_TXBCON1: + case REG_GATECLK: + case REG_TXTIME: + case REG_HSYMTMRL: + case REG_HSYMTMRH: + case REG_SOFTRST: + case REG_SECCON0: + case REG_SECCON1: + case REG_TXSTBL: + case REG_RXSR: + case REG_INTCON: + case REG_TRISGPIO: + case REG_GPIO: + case REG_RFCTL: + case REG_SLPACK: + case REG_BBREG0: + case REG_BBREG1: + case REG_BBREG2: + case REG_BBREG3: + case REG_BBREG4: + case REG_BBREG6: + case REG_CCAEDTH: + return true; + default: + return false; + } +} - ret = spi_sync(devrec->spi, &msg); - if (ret) - dev_err(printdev(devrec), - "SPI write Failed for short register 0x%hhx\n", reg); +static bool +mrf24j40_short_reg_readable(struct device *dev, unsigned int reg) +{ + bool rc; - mutex_unlock(&devrec->buffer_mutex); - return ret; + /* all writeable are also readable */ + rc = mrf24j40_short_reg_writeable(dev, reg); + if (rc) + return rc; + + /* readonly regs */ + switch (reg) { + case REG_TXSTAT: + case REG_INTSTAT: + return true; + default: + return false; + } } -static int read_short_reg(struct mrf24j40 *devrec, u8 reg, u8 *val) +static bool +mrf24j40_short_reg_volatile(struct device *dev, unsigned int reg) { - int ret = -1; - struct spi_message msg; - struct spi_transfer xfer = { - .len = 2, - .tx_buf = devrec->buf, - .rx_buf = devrec->buf, - }; - - spi_message_init(&msg); - spi_message_add_tail(&xfer, &msg); - - mutex_lock(&devrec->buffer_mutex); - devrec->buf[0] = MRF24J40_READSHORT(reg); - devrec->buf[1] = 0; - - ret = spi_sync(devrec->spi, &msg); - if (ret) - dev_err(printdev(devrec), - "SPI read Failed for short register 0x%hhx\n", reg); - else - *val = devrec->buf[1]; + /* can be changed during runtime */ + switch (reg) { + case REG_TXSTAT: + case REG_INTSTAT: + case REG_RXFLUSH: + case REG_TXNCON: + case REG_SOFTRST: + case REG_RFCTL: + case REG_TXBCON0: + case REG_TXG1CON: + case REG_TXG2CON: + case REG_TXBCON1: + case REG_SECCON0: + case REG_RXSR: + case REG_SLPACK: + case REG_SECCR2: + case REG_BBREG6: + /* use them in spi_async and regmap so it's volatile */ + case REG_BBREG1: + return true; + default: + return false; + } +} - mutex_unlock(&devrec->buffer_mutex); - return ret; +static bool +mrf24j40_short_reg_precious(struct device *dev, unsigned int reg) +{ + /* don't clear irq line on read */ + switch (reg) { + case REG_INTSTAT: + return true; + default: + return false; + } +} + +static const struct regmap_config mrf24j40_short_regmap = { + .name = "mrf24j40_short", + .reg_bits = 7, + .val_bits = 8, + .pad_bits = 1, + .write_flag_mask = MRF24J40_SHORT_WRITE, + .read_flag_mask = MRF24J40_SHORT_READ, + .cache_type = REGCACHE_RBTREE, + .max_register = MRF24J40_SHORT_NUMREGS, + .writeable_reg = mrf24j40_short_reg_writeable, + .readable_reg = mrf24j40_short_reg_readable, + .volatile_reg = mrf24j40_short_reg_volatile, + .precious_reg = mrf24j40_short_reg_precious, +}; + +static bool +mrf24j40_long_reg_writeable(struct device *dev, unsigned int reg) +{ + switch (reg) { + case REG_RFCON0: + case REG_RFCON1: + case REG_RFCON2: + case REG_RFCON3: + case REG_RFCON5: + case REG_RFCON6: + case REG_RFCON7: + case REG_RFCON8: + case REG_SLPCAL2: + case REG_SLPCON0: + case REG_SLPCON1: + case REG_WAKETIMEL: + case REG_WAKETIMEH: + case REG_REMCNTL: + case REG_REMCNTH: + case REG_MAINCNT0: + case REG_MAINCNT1: + case REG_MAINCNT2: + case REG_MAINCNT3: + case REG_TESTMODE: + case REG_ASSOEAR0: + case REG_ASSOEAR1: + case REG_ASSOEAR2: + case REG_ASSOEAR3: + case REG_ASSOEAR4: + case REG_ASSOEAR5: + case REG_ASSOEAR6: + case REG_ASSOEAR7: + case REG_ASSOSAR0: + case REG_ASSOSAR1: + case REG_UNONCE0: + case REG_UNONCE1: + case REG_UNONCE2: + case REG_UNONCE3: + case REG_UNONCE4: + case REG_UNONCE5: + case REG_UNONCE6: + case REG_UNONCE7: + case REG_UNONCE8: + case REG_UNONCE9: + case REG_UNONCE10: + case REG_UNONCE11: + case REG_UNONCE12: + return true; + default: + return false; + } } -static int read_long_reg(struct mrf24j40 *devrec, u16 reg, u8 *value) +static bool +mrf24j40_long_reg_readable(struct device *dev, unsigned int reg) { - int ret; - u16 cmd; - struct spi_message msg; - struct spi_transfer xfer = { - .len = 3, - .tx_buf = devrec->buf, - .rx_buf = devrec->buf, - }; - - spi_message_init(&msg); - spi_message_add_tail(&xfer, &msg); - - cmd = MRF24J40_READLONG(reg); - mutex_lock(&devrec->buffer_mutex); - devrec->buf[0] = cmd >> 8 & 0xff; - devrec->buf[1] = cmd & 0xff; - devrec->buf[2] = 0; - - ret = spi_sync(devrec->spi, &msg); - if (ret) - dev_err(printdev(devrec), - "SPI read Failed for long register 0x%hx\n", reg); - else - *value = devrec->buf[2]; + bool rc; - mutex_unlock(&devrec->buffer_mutex); - return ret; + /* all writeable are also readable */ + rc = mrf24j40_long_reg_writeable(dev, reg); + if (rc) + return rc; + + /* readonly regs */ + switch (reg) { + case REG_SLPCAL0: + case REG_SLPCAL1: + case REG_RFSTATE: + case REG_RSSI: + return true; + default: + return false; + } +} + +static bool +mrf24j40_long_reg_volatile(struct device *dev, unsigned int reg) +{ + /* can be changed during runtime */ + switch (reg) { + case REG_SLPCAL0: + case REG_SLPCAL1: + case REG_SLPCAL2: + case REG_RFSTATE: + case REG_RSSI: + case REG_MAINCNT3: + return true; + default: + return false; + } +} + +static const struct regmap_config mrf24j40_long_regmap = { + .name = "mrf24j40_long", + .reg_bits = 11, + .val_bits = 8, + .pad_bits = 5, + .write_flag_mask = MRF24J40_LONG_ACCESS, + .read_flag_mask = MRF24J40_LONG_ACCESS, + .cache_type = REGCACHE_RBTREE, + .max_register = MRF24J40_LONG_NUMREGS, + .writeable_reg = mrf24j40_long_reg_writeable, + .readable_reg = mrf24j40_long_reg_readable, + .volatile_reg = mrf24j40_long_reg_volatile, +}; + +static int mrf24j40_long_regmap_write(void *context, const void *data, + size_t count) +{ + struct spi_device *spi = context; + u8 buf[3]; + + if (count > 3) + return -EINVAL; + + /* regmap supports read/write mask only in frist byte + * long write access need to set the 12th bit, so we + * make special handling for write. + */ + memcpy(buf, data, count); + buf[1] |= (1 << 4); + + return spi_write(spi, buf, count); } -static int write_long_reg(struct mrf24j40 *devrec, u16 reg, u8 val) +static int +mrf24j40_long_regmap_read(void *context, const void *reg, size_t reg_size, + void *val, size_t val_size) +{ + struct spi_device *spi = context; + + return spi_write_then_read(spi, reg, reg_size, val, val_size); +} + +static const struct regmap_bus mrf24j40_long_regmap_bus = { + .write = mrf24j40_long_regmap_write, + .read = mrf24j40_long_regmap_read, + .reg_format_endian_default = REGMAP_ENDIAN_BIG, + .val_format_endian_default = REGMAP_ENDIAN_BIG, +}; + +static void write_tx_buf_complete(void *context) { + struct mrf24j40 *devrec = context; + __le16 fc = ieee802154_get_fc_from_skb(devrec->tx_skb); + u8 val = BIT_TXNTRIG; int ret; - u16 cmd; - struct spi_message msg; - struct spi_transfer xfer = { - .len = 3, - .tx_buf = devrec->buf, - .rx_buf = devrec->buf, - }; - spi_message_init(&msg); - spi_message_add_tail(&xfer, &msg); + if (ieee802154_is_ackreq(fc)) + val |= BIT_TXNACKREQ; - cmd = MRF24J40_WRITELONG(reg); - mutex_lock(&devrec->buffer_mutex); - devrec->buf[0] = cmd >> 8 & 0xff; - devrec->buf[1] = cmd & 0xff; - devrec->buf[2] = val; + devrec->tx_post_msg.complete = NULL; + devrec->tx_post_buf[0] = MRF24J40_WRITESHORT(REG_TXNCON); + devrec->tx_post_buf[1] = val; - ret = spi_sync(devrec->spi, &msg); + ret = spi_async(devrec->spi, &devrec->tx_post_msg); if (ret) - dev_err(printdev(devrec), - "SPI write Failed for long register 0x%hx\n", reg); - - mutex_unlock(&devrec->buffer_mutex); - return ret; + dev_err(printdev(devrec), "SPI write Failed for transmit buf\n"); } /* This function relies on an undocumented write method. Once a write command @@ -218,22 +565,8 @@ static int write_tx_buf(struct mrf24j40 *devrec, u16 reg, const u8 *data, size_t length) { - int ret; u16 cmd; - u8 lengths[2]; - struct spi_message msg; - struct spi_transfer addr_xfer = { - .len = 2, - .tx_buf = devrec->buf, - }; - struct spi_transfer lengths_xfer = { - .len = 2, - .tx_buf = &lengths, /* TODO: Is DMA really required for SPI? */ - }; - struct spi_transfer data_xfer = { - .len = length, - .tx_buf = data, - }; + int ret; /* Range check the length. 2 bytes are used for the length fields.*/ if (length > TX_FIFO_SIZE-2) { @@ -241,194 +574,64 @@ length = TX_FIFO_SIZE-2; } - spi_message_init(&msg); - spi_message_add_tail(&addr_xfer, &msg); - spi_message_add_tail(&lengths_xfer, &msg); - spi_message_add_tail(&data_xfer, &msg); - cmd = MRF24J40_WRITELONG(reg); - mutex_lock(&devrec->buffer_mutex); - devrec->buf[0] = cmd >> 8 & 0xff; - devrec->buf[1] = cmd & 0xff; - lengths[0] = 0x0; /* Header Length. Set to 0 for now. TODO */ - lengths[1] = length; /* Total length */ + devrec->tx_hdr_buf[0] = cmd >> 8 & 0xff; + devrec->tx_hdr_buf[1] = cmd & 0xff; + devrec->tx_len_buf[0] = 0x0; /* Header Length. Set to 0 for now. TODO */ + devrec->tx_len_buf[1] = length; /* Total length */ + devrec->tx_buf_trx.tx_buf = data; + devrec->tx_buf_trx.len = length; - ret = spi_sync(devrec->spi, &msg); + ret = spi_async(devrec->spi, &devrec->tx_msg); if (ret) dev_err(printdev(devrec), "SPI write Failed for TX buf\n"); - mutex_unlock(&devrec->buffer_mutex); - return ret; -} - -static int mrf24j40_read_rx_buf(struct mrf24j40 *devrec, - u8 *data, u8 *len, u8 *lqi) -{ - u8 rx_len; - u8 addr[2]; - u8 lqi_rssi[2]; - u16 cmd; - int ret; - struct spi_message msg; - struct spi_transfer addr_xfer = { - .len = 2, - .tx_buf = &addr, - }; - struct spi_transfer data_xfer = { - .len = 0x0, /* set below */ - .rx_buf = data, - }; - struct spi_transfer status_xfer = { - .len = 2, - .rx_buf = &lqi_rssi, - }; - - /* Get the length of the data in the RX FIFO. The length in this - * register exclues the 1-byte length field at the beginning. */ - ret = read_long_reg(devrec, REG_RX_FIFO, &rx_len); - if (ret) - goto out; - - /* Range check the RX FIFO length, accounting for the one-byte - * length field at the begining. */ - if (rx_len > RX_FIFO_SIZE-1) { - dev_err(printdev(devrec), "Invalid length read from device. Performing short read.\n"); - rx_len = RX_FIFO_SIZE-1; - } - - if (rx_len > *len) { - /* Passed in buffer wasn't big enough. Should never happen. */ - dev_err(printdev(devrec), "Buffer not big enough. Performing short read\n"); - rx_len = *len; - } - - /* Set up the commands to read the data. */ - cmd = MRF24J40_READLONG(REG_RX_FIFO+1); - addr[0] = cmd >> 8 & 0xff; - addr[1] = cmd & 0xff; - data_xfer.len = rx_len; - - spi_message_init(&msg); - spi_message_add_tail(&addr_xfer, &msg); - spi_message_add_tail(&data_xfer, &msg); - spi_message_add_tail(&status_xfer, &msg); - - ret = spi_sync(devrec->spi, &msg); - if (ret) { - dev_err(printdev(devrec), "SPI RX Buffer Read Failed.\n"); - goto out; - } - - *lqi = lqi_rssi[0]; - *len = rx_len; - -#ifdef DEBUG - print_hex_dump(KERN_DEBUG, "mrf24j40 rx: ", - DUMP_PREFIX_OFFSET, 16, 1, data, *len, 0); - printk(KERN_DEBUG "mrf24j40 rx: lqi: %02hhx rssi: %02hhx\n", - lqi_rssi[0], lqi_rssi[1]); -#endif - -out: return ret; } -static int mrf24j40_tx(struct ieee802154_dev *dev, struct sk_buff *skb) +static int mrf24j40_tx(struct ieee802154_hw *hw, struct sk_buff *skb) { - struct mrf24j40 *devrec = dev->priv; - u8 val; - int ret = 0; + struct mrf24j40 *devrec = hw->priv; dev_dbg(printdev(devrec), "tx packet of %d bytes\n", skb->len); + devrec->tx_skb = skb; - ret = write_tx_buf(devrec, 0x000, skb->data, skb->len); - if (ret) - goto err; - - /* Set TXNTRIG bit of TXNCON to send packet */ - ret = read_short_reg(devrec, REG_TXNCON, &val); - if (ret) - goto err; - val |= 0x1; - /* Set TXNACKREQ if the ACK bit is set in the packet. */ - if (skb->data[0] & IEEE802154_FC_ACK_REQ) - val |= 0x4; - write_short_reg(devrec, REG_TXNCON, val); - - INIT_COMPLETION(devrec->tx_complete); - - /* Wait for the device to send the TX complete interrupt. */ - ret = wait_for_completion_interruptible_timeout( - &devrec->tx_complete, - 5 * HZ); - if (ret == -ERESTARTSYS) - goto err; - if (ret == 0) { - dev_warn(printdev(devrec), "Timeout waiting for TX interrupt\n"); - ret = -ETIMEDOUT; - goto err; - } - - /* Check for send error from the device. */ - ret = read_short_reg(devrec, REG_TXSTAT, &val); - if (ret) - goto err; - if (val & 0x1) { - dev_dbg(printdev(devrec), "Error Sending. Retry count exceeded\n"); - ret = -ECOMM; /* TODO: Better error code ? */ - } else - dev_dbg(printdev(devrec), "Packet Sent\n"); - -err: - - return ret; + return write_tx_buf(devrec, 0x000, skb->data, skb->len); } -static int mrf24j40_ed(struct ieee802154_dev *dev, u8 *level) +static int mrf24j40_ed(struct ieee802154_hw *hw, u8 *level) { /* TODO: */ - printk(KERN_WARNING "mrf24j40: ed not implemented\n"); + pr_warn("mrf24j40: ed not implemented\n"); *level = 0; return 0; } -static int mrf24j40_start(struct ieee802154_dev *dev) +static int mrf24j40_start(struct ieee802154_hw *hw) { - struct mrf24j40 *devrec = dev->priv; - u8 val; - int ret; + struct mrf24j40 *devrec = hw->priv; dev_dbg(printdev(devrec), "start\n"); - ret = read_short_reg(devrec, REG_INTCON, &val); - if (ret) - return ret; - val &= ~(0x1|0x8); /* Clear TXNIE and RXIE. Enable interrupts */ - write_short_reg(devrec, REG_INTCON, val); - - return 0; + /* Clear TXNIE and RXIE. Enable interrupts */ + return regmap_update_bits(devrec->regmap_short, REG_INTCON, + BIT_TXNIE | BIT_RXIE, 0); } -static void mrf24j40_stop(struct ieee802154_dev *dev) +static void mrf24j40_stop(struct ieee802154_hw *hw) { - struct mrf24j40 *devrec = dev->priv; - u8 val; - int ret; - dev_dbg(printdev(devrec), "stop\n"); + struct mrf24j40 *devrec = hw->priv; - ret = read_short_reg(devrec, REG_INTCON, &val); - if (ret) - return; - val |= 0x1|0x8; /* Set TXNIE and RXIE. Disable Interrupts */ - write_short_reg(devrec, REG_INTCON, val); + dev_dbg(printdev(devrec), "stop\n"); - return; + /* Set TXNIE and RXIE. Disable Interrupts */ + regmap_update_bits(devrec->regmap_short, REG_INTCON, + BIT_TXNIE | BIT_TXNIE, BIT_TXNIE | BIT_TXNIE); } -static int mrf24j40_set_channel(struct ieee802154_dev *dev, - int page, int channel) +static int mrf24j40_set_channel(struct ieee802154_hw *hw, u8 page, u8 channel) { - struct mrf24j40 *devrec = dev->priv; + struct mrf24j40 *devrec = hw->priv; u8 val; int ret; @@ -439,285 +642,709 @@ WARN_ON(channel > MRF24J40_CHAN_MAX); /* Set Channel TODO */ - val = (channel-11) << 4 | 0x03; - write_long_reg(devrec, REG_RFCON0, val); + val = (channel - 11) << RFCON0_CH_SHIFT | RFOPT_RECOMMEND; + ret = regmap_update_bits(devrec->regmap_long, REG_RFCON0, + RFCON0_CH_MASK, val); + if (ret) + return ret; /* RF Reset */ - ret = read_short_reg(devrec, REG_RFCTL, &val); + ret = regmap_update_bits(devrec->regmap_short, REG_RFCTL, BIT_RFRST, + BIT_RFRST); if (ret) return ret; - val |= 0x04; - write_short_reg(devrec, REG_RFCTL, val); - val &= ~0x04; - write_short_reg(devrec, REG_RFCTL, val); - udelay(SET_CHANNEL_DELAY_US); /* per datasheet */ + ret = regmap_update_bits(devrec->regmap_short, REG_RFCTL, BIT_RFRST, 0); + if (!ret) + udelay(SET_CHANNEL_DELAY_US); /* per datasheet */ - return 0; + return ret; } -static int mrf24j40_filter(struct ieee802154_dev *dev, +static int mrf24j40_filter(struct ieee802154_hw *hw, struct ieee802154_hw_addr_filt *filt, unsigned long changed) { - struct mrf24j40 *devrec = dev->priv; + struct mrf24j40 *devrec = hw->priv; dev_dbg(printdev(devrec), "filter\n"); - if (changed & IEEE802515_AFILT_SADDR_CHANGED) { + if (changed & IEEE802154_AFILT_SADDR_CHANGED) { /* Short Addr */ u8 addrh, addrl; - addrh = filt->short_addr >> 8 & 0xff; - addrl = filt->short_addr & 0xff; - write_short_reg(devrec, REG_SADRH, addrh); - write_short_reg(devrec, REG_SADRL, addrl); + addrh = le16_to_cpu(filt->short_addr) >> 8 & 0xff; + addrl = le16_to_cpu(filt->short_addr) & 0xff; + + regmap_write(devrec->regmap_short, REG_SADRH, addrh); + regmap_write(devrec->regmap_short, REG_SADRL, addrl); dev_dbg(printdev(devrec), "Set short addr to %04hx\n", filt->short_addr); } - if (changed & IEEE802515_AFILT_IEEEADDR_CHANGED) { + if (changed & IEEE802154_AFILT_IEEEADDR_CHANGED) { /* Device Address */ - int i; + u8 i, addr[8]; + + memcpy(addr, &filt->ieee_addr, 8); for (i = 0; i < 8; i++) - write_short_reg(devrec, REG_EADR0+i, - filt->ieee_addr[7-i]); + regmap_write(devrec->regmap_short, REG_EADR0 + i, + addr[i]); #ifdef DEBUG - printk(KERN_DEBUG "Set long addr to: "); + pr_debug("Set long addr to: "); for (i = 0; i < 8; i++) - printk("%02hhx ", filt->ieee_addr[i]); - printk(KERN_DEBUG "\n"); + pr_debug("%02hhx ", addr[7 - i]); + pr_debug("\n"); #endif } - if (changed & IEEE802515_AFILT_PANID_CHANGED) { + if (changed & IEEE802154_AFILT_PANID_CHANGED) { /* PAN ID */ u8 panidl, panidh; - panidh = filt->pan_id >> 8 & 0xff; - panidl = filt->pan_id & 0xff; - write_short_reg(devrec, REG_PANIDH, panidh); - write_short_reg(devrec, REG_PANIDL, panidl); + + panidh = le16_to_cpu(filt->pan_id) >> 8 & 0xff; + panidl = le16_to_cpu(filt->pan_id) & 0xff; + regmap_write(devrec->regmap_short, REG_PANIDH, panidh); + regmap_write(devrec->regmap_short, REG_PANIDL, panidl); dev_dbg(printdev(devrec), "Set PANID to %04hx\n", filt->pan_id); } - if (changed & IEEE802515_AFILT_PANC_CHANGED) { + if (changed & IEEE802154_AFILT_PANC_CHANGED) { /* Pan Coordinator */ u8 val; int ret; - ret = read_short_reg(devrec, REG_RXMCR, &val); - if (ret) - return ret; if (filt->pan_coord) - val |= 0x8; + val = BIT_PANCOORD; else - val &= ~0x8; - write_short_reg(devrec, REG_RXMCR, val); + val = 0; + ret = regmap_update_bits(devrec->regmap_short, REG_RXMCR, + BIT_PANCOORD, val); + if (ret) + return ret; /* REG_SLOTTED is maintained as default (unslotted/CSMA-CA). * REG_ORDER is maintained as default (no beacon/superframe). */ dev_dbg(printdev(devrec), "Set Pan Coord to %s\n", - filt->pan_coord ? "on" : "off"); + filt->pan_coord ? "on" : "off"); } return 0; } -static int mrf24j40_handle_rx(struct mrf24j40 *devrec) +static void mrf24j40_handle_rx_read_buf_unlock(struct mrf24j40 *devrec) { - u8 len = RX_FIFO_SIZE; - u8 lqi = 0; - u8 val; - int ret = 0; - struct sk_buff *skb; + int ret; - /* Turn off reception of packets off the air. This prevents the - * device from overwriting the buffer while we're reading it. */ - ret = read_short_reg(devrec, REG_BBREG1, &val); + /* Turn back on reception of packets off the air. */ + devrec->rx_msg.complete = NULL; + devrec->rx_buf[0] = MRF24J40_WRITESHORT(REG_BBREG1); + devrec->rx_buf[1] = 0x00; /* CLR RXDECINV */ + ret = spi_async(devrec->spi, &devrec->rx_msg); if (ret) - goto out; - val |= 4; /* SET RXDECINV */ - write_short_reg(devrec, REG_BBREG1, val); + dev_err(printdev(devrec), "failed to unlock rx buffer\n"); +} + +static void mrf24j40_handle_rx_read_buf_complete(void *context) +{ + struct mrf24j40 *devrec = context; + u8 len = devrec->rx_buf[2]; + u8 rx_local_buf[RX_FIFO_SIZE]; + struct sk_buff *skb; + + memcpy(rx_local_buf, devrec->rx_fifo_buf, len); + mrf24j40_handle_rx_read_buf_unlock(devrec); - skb = alloc_skb(len, GFP_KERNEL); + skb = dev_alloc_skb(IEEE802154_MTU); if (!skb) { - ret = -ENOMEM; - goto out; + dev_err(printdev(devrec), "failed to allocate skb\n"); + return; } - ret = mrf24j40_read_rx_buf(devrec, skb_put(skb, len), &len, &lqi); - if (ret < 0) { - dev_err(printdev(devrec), "Failure reading RX FIFO\n"); - kfree_skb(skb); - ret = -EINVAL; - goto out; + memcpy(skb_put(skb, len), rx_local_buf, len); + ieee802154_rx_irqsafe(devrec->hw, skb, 0); + +#ifdef DEBUG + print_hex_dump(KERN_DEBUG, "mrf24j40 rx: ", DUMP_PREFIX_OFFSET, 16, 1, + rx_local_buf, len, 0); + pr_debug("mrf24j40 rx: lqi: %02hhx rssi: %02hhx\n", + devrec->rx_lqi_buf[0], devrec->rx_lqi_buf[1]); +#endif +} + +static void mrf24j40_handle_rx_read_buf(void *context) +{ + struct mrf24j40 *devrec = context; + u16 cmd; + int ret; + + /* if length is invalid read the full MTU */ + if (!ieee802154_is_valid_psdu_len(devrec->rx_buf[2])) + devrec->rx_buf[2] = IEEE802154_MTU; + + cmd = MRF24J40_READLONG(REG_RX_FIFO + 1); + devrec->rx_addr_buf[0] = cmd >> 8 & 0xff; + devrec->rx_addr_buf[1] = cmd & 0xff; + devrec->rx_fifo_buf_trx.len = devrec->rx_buf[2]; + ret = spi_async(devrec->spi, &devrec->rx_buf_msg); + if (ret) { + dev_err(printdev(devrec), "failed to read rx buffer\n"); + mrf24j40_handle_rx_read_buf_unlock(devrec); + } +} + +static void mrf24j40_handle_rx_read_len(void *context) +{ + struct mrf24j40 *devrec = context; + u16 cmd; + int ret; + + /* read the length of received frame */ + devrec->rx_msg.complete = mrf24j40_handle_rx_read_buf; + devrec->rx_trx.len = 3; + cmd = MRF24J40_READLONG(REG_RX_FIFO); + devrec->rx_buf[0] = cmd >> 8 & 0xff; + devrec->rx_buf[1] = cmd & 0xff; + + ret = spi_async(devrec->spi, &devrec->rx_msg); + if (ret) { + dev_err(printdev(devrec), "failed to read rx buffer length\n"); + mrf24j40_handle_rx_read_buf_unlock(devrec); } +} - /* Cut off the checksum */ - skb_trim(skb, len-2); +static int mrf24j40_handle_rx(struct mrf24j40 *devrec) +{ + /* Turn off reception of packets off the air. This prevents the + * device from overwriting the buffer while we're reading it. + */ + devrec->rx_msg.complete = mrf24j40_handle_rx_read_len; + devrec->rx_trx.len = 2; + devrec->rx_buf[0] = MRF24J40_WRITESHORT(REG_BBREG1); + devrec->rx_buf[1] = BIT_RXDECINV; /* SET RXDECINV */ - /* TODO: Other drivers call ieee20154_rx_irqsafe() here (eg: cc2040, - * also from a workqueue). I think irqsafe is not necessary here. - * Can someone confirm? */ - ieee802154_rx_irqsafe(devrec->dev, skb, lqi); + return spi_async(devrec->spi, &devrec->rx_msg); +} - dev_dbg(printdev(devrec), "RX Handled\n"); +static int +mrf24j40_csma_params(struct ieee802154_hw *hw, u8 min_be, u8 max_be, + u8 retries) +{ + struct mrf24j40 *devrec = hw->priv; + u8 val; -out: - /* Turn back on reception of packets off the air. */ - ret = read_short_reg(devrec, REG_BBREG1, &val); - if (ret) - return ret; - val &= ~0x4; /* Clear RXDECINV */ - write_short_reg(devrec, REG_BBREG1, val); + /* min_be */ + val = min_be << TXMCR_MIN_BE_SHIFT; + /* csma backoffs */ + val |= retries << TXMCR_CSMA_RETRIES_SHIFT; + + return regmap_update_bits(devrec->regmap_short, REG_TXMCR, + TXMCR_MIN_BE_MASK | TXMCR_CSMA_RETRIES_MASK, + val); +} + +static int mrf24j40_set_cca_mode(struct ieee802154_hw *hw, + const struct wpan_phy_cca *cca) +{ + struct mrf24j40 *devrec = hw->priv; + u8 val; + + /* mapping 802.15.4 to driver spec */ + switch (cca->mode) { + case NL802154_CCA_ENERGY: + val = 2; + break; + case NL802154_CCA_CARRIER: + val = 1; + break; + case NL802154_CCA_ENERGY_CARRIER: + switch (cca->opt) { + case NL802154_CCA_OPT_ENERGY_CARRIER_AND: + val = 3; + break; + default: + return -EINVAL; + } + break; + default: + return -EINVAL; + } + + return regmap_update_bits(devrec->regmap_short, REG_BBREG2, + BBREG2_CCA_MODE_MASK, + val << BBREG2_CCA_MODE_SHIFT); +} + +/* array for representing ed levels */ +static const s32 mrf24j40_ed_levels[] = { + -9000, -8900, -8800, -8700, -8600, -8500, -8400, -8300, -8200, -8100, + -8000, -7900, -7800, -7700, -7600, -7500, -7400, -7300, -7200, -7100, + -7000, -6900, -6800, -6700, -6600, -6500, -6400, -6300, -6200, -6100, + -6000, -5900, -5800, -5700, -5600, -5500, -5400, -5300, -5200, -5100, + -5000, -4900, -4800, -4700, -4600, -4500, -4400, -4300, -4200, -4100, + -4000, -3900, -3800, -3700, -3600, -3500 +}; + +/* map ed levels to register value */ +static const s32 mrf24j40_ed_levels_map[][2] = { + { -9000, 0 }, { -8900, 1 }, { -8800, 2 }, { -8700, 5 }, { -8600, 9 }, + { -8500, 13 }, { -8400, 18 }, { -8300, 23 }, { -8200, 27 }, + { -8100, 32 }, { -8000, 37 }, { -7900, 43 }, { -7800, 48 }, + { -7700, 53 }, { -7600, 58 }, { -7500, 63 }, { -7400, 68 }, + { -7300, 73 }, { -7200, 78 }, { -7100, 83 }, { -7000, 89 }, + { -6900, 95 }, { -6800, 100 }, { -6700, 107 }, { -6600, 111 }, + { -6500, 117 }, { -6400, 121 }, { -6300, 125 }, { -6200, 129 }, + { -6100, 133 }, { -6000, 138 }, { -5900, 143 }, { -5800, 148 }, + { -5700, 153 }, { -5600, 159 }, { -5500, 165 }, { -5400, 170 }, + { -5300, 176 }, { -5200, 183 }, { -5100, 188 }, { -5000, 193 }, + { -4900, 198 }, { -4800, 203 }, { -4700, 207 }, { -4600, 212 }, + { -4500, 216 }, { -4400, 221 }, { -4300, 225 }, { -4200, 228 }, + { -4100, 233 }, { -4000, 239 }, { -3900, 245 }, { -3800, 250 }, + { -3700, 253 }, { -3600, 254 }, { -3500, 255 }, +}; + +static int mrf24j40_set_cca_ed_level(struct ieee802154_hw *hw, s32 mbm) +{ + struct mrf24j40 *devrec = hw->priv; + int i; + + for (i = 0; i < ARRAY_SIZE(mrf24j40_ed_levels_map); i++) { + if (mrf24j40_ed_levels_map[i][0] == mbm) + return regmap_write(devrec->regmap_short, REG_CCAEDTH, + mrf24j40_ed_levels_map[i][1]); + } + + return -EINVAL; +} + +static const s32 mrf24j40ma_powers[] = { + 0, -50, -120, -190, -280, -370, -490, -630, -1000, -1050, -1120, -1190, + -1280, -1370, -1490, -1630, -2000, -2050, -2120, -2190, -2280, -2370, + -2490, -2630, -3000, -3050, -3120, -3190, -3280, -3370, -3490, -3630, +}; + +static int mrf24j40_set_txpower(struct ieee802154_hw *hw, s32 mbm) +{ + struct mrf24j40 *devrec = hw->priv; + s32 small_scale; + u8 val; + + if (0 >= mbm && mbm > -1000) { + val = TXPWRL_0 << TXPWRL_SHIFT; + small_scale = mbm; + } else if (-1000 >= mbm && mbm > -2000) { + val = TXPWRL_10 << TXPWRL_SHIFT; + small_scale = mbm + 1000; + } else if (-2000 >= mbm && mbm > -3000) { + val = TXPWRL_20 << TXPWRL_SHIFT; + small_scale = mbm + 2000; + } else if (-3000 >= mbm && mbm > -4000) { + val = TXPWRL_30 << TXPWRL_SHIFT; + small_scale = mbm + 3000; + } else { + return -EINVAL; + } + + switch (small_scale) { + case 0: + val |= (TXPWRS_0 << TXPWRS_SHIFT); + break; + case -50: + val |= (TXPWRS_0_5 << TXPWRS_SHIFT); + break; + case -120: + val |= (TXPWRS_1_2 << TXPWRS_SHIFT); + break; + case -190: + val |= (TXPWRS_1_9 << TXPWRS_SHIFT); + break; + case -280: + val |= (TXPWRS_2_8 << TXPWRS_SHIFT); + break; + case -370: + val |= (TXPWRS_3_7 << TXPWRS_SHIFT); + break; + case -490: + val |= (TXPWRS_4_9 << TXPWRS_SHIFT); + break; + case -630: + val |= (TXPWRS_6_3 << TXPWRS_SHIFT); + break; + default: + return -EINVAL; + } + + return regmap_update_bits(devrec->regmap_long, REG_RFCON3, + TXPWRL_MASK | TXPWRS_MASK, val); +} + +static int mrf24j40_set_promiscuous_mode(struct ieee802154_hw *hw, bool on) +{ + struct mrf24j40 *devrec = hw->priv; + int ret; + + if (on) { + /* set PROMI, ERRPKT and NOACKRSP */ + ret = regmap_update_bits(devrec->regmap_short, REG_RXMCR, + BIT_PROMI | BIT_ERRPKT | BIT_NOACKRSP, + BIT_PROMI | BIT_ERRPKT | BIT_NOACKRSP); + } else { + /* clear PROMI, ERRPKT and NOACKRSP */ + ret = regmap_update_bits(devrec->regmap_short, REG_RXMCR, + BIT_PROMI | BIT_ERRPKT | BIT_NOACKRSP, + 0); + } return ret; } -static struct ieee802154_ops mrf24j40_ops = { +static const struct ieee802154_ops mrf24j40_ops = { .owner = THIS_MODULE, - .xmit = mrf24j40_tx, + .xmit_async = mrf24j40_tx, .ed = mrf24j40_ed, .start = mrf24j40_start, .stop = mrf24j40_stop, .set_channel = mrf24j40_set_channel, .set_hw_addr_filt = mrf24j40_filter, + .set_csma_params = mrf24j40_csma_params, + .set_cca_mode = mrf24j40_set_cca_mode, + .set_cca_ed_level = mrf24j40_set_cca_ed_level, + .set_txpower = mrf24j40_set_txpower, + .set_promiscuous_mode = mrf24j40_set_promiscuous_mode, }; +static void mrf24j40_intstat_complete(void *context) +{ + struct mrf24j40 *devrec = context; + u8 intstat = devrec->irq_buf[1]; + + enable_irq(devrec->spi->irq); + + /* Check for TX complete */ + if (intstat & BIT_TXNIF) + ieee802154_xmit_complete(devrec->hw, devrec->tx_skb, false); + + /* Check for Rx */ + if (intstat & BIT_RXIF) + mrf24j40_handle_rx(devrec); +} + static irqreturn_t mrf24j40_isr(int irq, void *data) { struct mrf24j40 *devrec = data; + int ret; disable_irq_nosync(irq); - schedule_work(&devrec->irqwork); + devrec->irq_buf[0] = MRF24J40_READSHORT(REG_INTSTAT); + /* Read the interrupt status */ + ret = spi_async(devrec->spi, &devrec->irq_msg); + if (ret) { + enable_irq(irq); + return IRQ_NONE; + } return IRQ_HANDLED; } -static void mrf24j40_isrwork(struct work_struct *work) +static int mrf24j40_hw_init(struct mrf24j40 *devrec) { - struct mrf24j40 *devrec = container_of(work, struct mrf24j40, irqwork); - u8 intstat; + u32 irq_type; int ret; - /* Read the interrupt status */ - ret = read_short_reg(devrec, REG_INTSTAT, &intstat); + /* Initialize the device. + From datasheet section 3.2: Initialization. */ + ret = regmap_write(devrec->regmap_short, REG_SOFTRST, 0x07); if (ret) - goto out; + goto err_ret; - /* Check for TX complete */ - if (intstat & 0x1) - complete(&devrec->tx_complete); + ret = regmap_write(devrec->regmap_short, REG_PACON2, 0x98); + if (ret) + goto err_ret; - /* Check for Rx */ - if (intstat & 0x8) - mrf24j40_handle_rx(devrec); + ret = regmap_write(devrec->regmap_short, REG_TXSTBL, 0x95); + if (ret) + goto err_ret; -out: - enable_irq(devrec->spi->irq); + ret = regmap_write(devrec->regmap_long, REG_RFCON0, 0x03); + if (ret) + goto err_ret; + + ret = regmap_write(devrec->regmap_long, REG_RFCON1, 0x01); + if (ret) + goto err_ret; + + ret = regmap_write(devrec->regmap_long, REG_RFCON2, 0x80); + if (ret) + goto err_ret; + + ret = regmap_write(devrec->regmap_long, REG_RFCON6, 0x90); + if (ret) + goto err_ret; + + ret = regmap_write(devrec->regmap_long, REG_RFCON7, 0x80); + if (ret) + goto err_ret; + + ret = regmap_write(devrec->regmap_long, REG_RFCON8, 0x10); + if (ret) + goto err_ret; + + ret = regmap_write(devrec->regmap_long, REG_SLPCON1, 0x21); + if (ret) + goto err_ret; + + ret = regmap_write(devrec->regmap_short, REG_BBREG2, 0x80); + if (ret) + goto err_ret; + + ret = regmap_write(devrec->regmap_short, REG_CCAEDTH, 0x60); + if (ret) + goto err_ret; + + ret = regmap_write(devrec->regmap_short, REG_BBREG6, 0x40); + if (ret) + goto err_ret; + + ret = regmap_write(devrec->regmap_short, REG_RFCTL, 0x04); + if (ret) + goto err_ret; + + ret = regmap_write(devrec->regmap_short, REG_RFCTL, 0x0); + if (ret) + goto err_ret; + + udelay(192); + + /* Set RX Mode. RXMCR<1:0>: 0x0 normal, 0x1 promisc, 0x2 error */ + ret = regmap_update_bits(devrec->regmap_short, REG_RXMCR, 0x03, 0x00); + if (ret) + goto err_ret; + + if (spi_get_device_id(devrec->spi)->driver_data == MRF24J40MC) { + /* Enable external amplifier. + * From MRF24J40MC datasheet section 1.3: Operation. + */ + regmap_update_bits(devrec->regmap_long, REG_TESTMODE, 0x07, + 0x07); + + /* Set GPIO3 as output. */ + regmap_update_bits(devrec->regmap_short, REG_TRISGPIO, 0x08, + 0x08); + + /* Set GPIO3 HIGH to enable U5 voltage regulator */ + regmap_update_bits(devrec->regmap_short, REG_GPIO, 0x08, 0x08); + + /* Reduce TX pwr to meet FCC requirements. + * From MRF24J40MC datasheet section 3.1.1 + */ + regmap_write(devrec->regmap_long, REG_RFCON3, 0x28); + } + + irq_type = irq_get_trigger_type(devrec->spi->irq); + if (irq_type == IRQ_TYPE_EDGE_RISING || + irq_type == IRQ_TYPE_EDGE_FALLING) + dev_warn(&devrec->spi->dev, + "Using edge triggered irq's are not recommended, because it can cause races and result in a non-functional driver!\n"); + switch (irq_type) { + case IRQ_TYPE_EDGE_RISING: + case IRQ_TYPE_LEVEL_HIGH: + /* set interrupt polarity to rising */ + ret = regmap_update_bits(devrec->regmap_long, REG_SLPCON0, + BIT_INTEDGE, BIT_INTEDGE); + if (ret) + goto err_ret; + break; + default: + /* default is falling edge */ + break; + } + + return 0; + +err_ret: + return ret; +} + +static void +mrf24j40_setup_tx_spi_messages(struct mrf24j40 *devrec) +{ + spi_message_init(&devrec->tx_msg); + devrec->tx_msg.context = devrec; + devrec->tx_msg.complete = write_tx_buf_complete; + devrec->tx_hdr_trx.len = 2; + devrec->tx_hdr_trx.tx_buf = devrec->tx_hdr_buf; + spi_message_add_tail(&devrec->tx_hdr_trx, &devrec->tx_msg); + devrec->tx_len_trx.len = 2; + devrec->tx_len_trx.tx_buf = devrec->tx_len_buf; + spi_message_add_tail(&devrec->tx_len_trx, &devrec->tx_msg); + spi_message_add_tail(&devrec->tx_buf_trx, &devrec->tx_msg); + + spi_message_init(&devrec->tx_post_msg); + devrec->tx_post_msg.context = devrec; + devrec->tx_post_trx.len = 2; + devrec->tx_post_trx.tx_buf = devrec->tx_post_buf; + spi_message_add_tail(&devrec->tx_post_trx, &devrec->tx_post_msg); +} + +static void +mrf24j40_setup_rx_spi_messages(struct mrf24j40 *devrec) +{ + spi_message_init(&devrec->rx_msg); + devrec->rx_msg.context = devrec; + devrec->rx_trx.len = 2; + devrec->rx_trx.tx_buf = devrec->rx_buf; + devrec->rx_trx.rx_buf = devrec->rx_buf; + spi_message_add_tail(&devrec->rx_trx, &devrec->rx_msg); + + spi_message_init(&devrec->rx_buf_msg); + devrec->rx_buf_msg.context = devrec; + devrec->rx_buf_msg.complete = mrf24j40_handle_rx_read_buf_complete; + devrec->rx_addr_trx.len = 2; + devrec->rx_addr_trx.tx_buf = devrec->rx_addr_buf; + spi_message_add_tail(&devrec->rx_addr_trx, &devrec->rx_buf_msg); + devrec->rx_fifo_buf_trx.rx_buf = devrec->rx_fifo_buf; + spi_message_add_tail(&devrec->rx_fifo_buf_trx, &devrec->rx_buf_msg); + devrec->rx_lqi_trx.len = 2; + devrec->rx_lqi_trx.rx_buf = devrec->rx_lqi_buf; + spi_message_add_tail(&devrec->rx_lqi_trx, &devrec->rx_buf_msg); +} + +static void +mrf24j40_setup_irq_spi_messages(struct mrf24j40 *devrec) +{ + spi_message_init(&devrec->irq_msg); + devrec->irq_msg.context = devrec; + devrec->irq_msg.complete = mrf24j40_intstat_complete; + devrec->irq_trx.len = 2; + devrec->irq_trx.tx_buf = devrec->irq_buf; + devrec->irq_trx.rx_buf = devrec->irq_buf; + spi_message_add_tail(&devrec->irq_trx, &devrec->irq_msg); +} + +static void mrf24j40_phy_setup(struct mrf24j40 *devrec) +{ + ieee802154_random_extended_addr(&devrec->hw->phy->perm_extended_addr); + devrec->hw->phy->current_channel = 11; + + /* mrf24j40 supports max_minbe 0 - 3 */ + devrec->hw->phy->supported.max_minbe = 3; + /* datasheet doesn't say anything about max_be, but we have min_be + * So we assume the max_be default. + */ + devrec->hw->phy->supported.min_maxbe = 5; + devrec->hw->phy->supported.max_maxbe = 5; + + devrec->hw->phy->cca.mode = NL802154_CCA_CARRIER; + devrec->hw->phy->supported.cca_modes = BIT(NL802154_CCA_ENERGY) | + BIT(NL802154_CCA_CARRIER) | + BIT(NL802154_CCA_ENERGY_CARRIER); + devrec->hw->phy->supported.cca_opts = BIT(NL802154_CCA_OPT_ENERGY_CARRIER_AND); + + devrec->hw->phy->cca_ed_level = -6900; + devrec->hw->phy->supported.cca_ed_levels = mrf24j40_ed_levels; + devrec->hw->phy->supported.cca_ed_levels_size = ARRAY_SIZE(mrf24j40_ed_levels); + + switch (spi_get_device_id(devrec->spi)->driver_data) { + case MRF24J40: + case MRF24J40MA: + devrec->hw->phy->supported.tx_powers = mrf24j40ma_powers; + devrec->hw->phy->supported.tx_powers_size = ARRAY_SIZE(mrf24j40ma_powers); + devrec->hw->phy->flags |= WPAN_PHY_FLAG_TXPOWER; + break; + default: + break; + } } static int mrf24j40_probe(struct spi_device *spi) { - int ret = -ENOMEM; - u8 val; + int ret = -ENOMEM, irq_type; + struct ieee802154_hw *hw; struct mrf24j40 *devrec; - struct pinctrl *pinctrl; - printk(KERN_INFO "mrf24j40: probe(). IRQ: %d\n", spi->irq); + dev_info(&spi->dev, "probe(). IRQ: %d\n", spi->irq); + + /* Register with the 802154 subsystem */ + + hw = ieee802154_alloc_hw(sizeof(*devrec), &mrf24j40_ops); + if (!hw) + goto err_ret; - devrec = kzalloc(sizeof(struct mrf24j40), GFP_KERNEL); - if (!devrec) - goto err_devrec; - devrec->buf = kzalloc(3, GFP_KERNEL); - if (!devrec->buf) - goto err_buf; - - pinctrl = devm_pinctrl_get_select_default(&spi->dev); - if (IS_ERR(pinctrl)) - dev_warn(&spi->dev, - "pinctrl pins are not configured from the driver"); - - spi->mode = SPI_MODE_0; /* TODO: Is this appropriate for right here? */ - if (spi->max_speed_hz > MAX_SPI_SPEED_HZ) - spi->max_speed_hz = MAX_SPI_SPEED_HZ; - - mutex_init(&devrec->buffer_mutex); - init_completion(&devrec->tx_complete); - INIT_WORK(&devrec->irqwork, mrf24j40_isrwork); + devrec = hw->priv; devrec->spi = spi; spi_set_drvdata(spi, devrec); + devrec->hw = hw; + devrec->hw->parent = &spi->dev; + devrec->hw->phy->supported.channels[0] = CHANNEL_MASK; + devrec->hw->flags = IEEE802154_HW_TX_OMIT_CKSUM | IEEE802154_HW_AFILT | + IEEE802154_HW_CSMA_PARAMS | + IEEE802154_HW_PROMISCUOUS; + + devrec->hw->phy->flags = WPAN_PHY_FLAG_CCA_MODE | + WPAN_PHY_FLAG_CCA_ED_LEVEL; + + mrf24j40_setup_tx_spi_messages(devrec); + mrf24j40_setup_rx_spi_messages(devrec); + mrf24j40_setup_irq_spi_messages(devrec); + + devrec->regmap_short = devm_regmap_init_spi(spi, + &mrf24j40_short_regmap); + if (IS_ERR(devrec->regmap_short)) { + ret = PTR_ERR(devrec->regmap_short); + dev_err(&spi->dev, "Failed to allocate short register map: %d\n", + ret); + goto err_register_device; + } - /* Register with the 802154 subsystem */ + devrec->regmap_long = devm_regmap_init(&spi->dev, + &mrf24j40_long_regmap_bus, + spi, &mrf24j40_long_regmap); + if (IS_ERR(devrec->regmap_long)) { + ret = PTR_ERR(devrec->regmap_long); + dev_err(&spi->dev, "Failed to allocate long register map: %d\n", + ret); + goto err_register_device; + } - devrec->dev = ieee802154_alloc_device(0, &mrf24j40_ops); - if (!devrec->dev) - goto err_alloc_dev; - - devrec->dev->priv = devrec; - devrec->dev->parent = &devrec->spi->dev; - devrec->dev->phy->channels_supported[0] = CHANNEL_MASK; - devrec->dev->flags = IEEE802154_HW_OMIT_CKSUM|IEEE802154_HW_AACK; + if (spi->max_speed_hz > MAX_SPI_SPEED_HZ) { + dev_warn(&spi->dev, "spi clock above possible maximum: %d", + MAX_SPI_SPEED_HZ); + return -EINVAL; + } - dev_dbg(printdev(devrec), "registered mrf24j40\n"); - ret = ieee802154_register_device(devrec->dev); + ret = mrf24j40_hw_init(devrec); if (ret) goto err_register_device; - /* Initialize the device. - From datasheet section 3.2: Initialization. */ - write_short_reg(devrec, REG_SOFTRST, 0x07); - write_short_reg(devrec, REG_PACON2, 0x98); - write_short_reg(devrec, REG_TXSTBL, 0x95); - write_long_reg(devrec, REG_RFCON0, 0x03); - write_long_reg(devrec, REG_RFCON1, 0x01); - write_long_reg(devrec, REG_RFCON2, 0x80); - write_long_reg(devrec, REG_RFCON6, 0x90); - write_long_reg(devrec, REG_RFCON7, 0x80); - write_long_reg(devrec, REG_RFCON8, 0x10); - write_long_reg(devrec, REG_SLPCON1, 0x21); - write_short_reg(devrec, REG_BBREG2, 0x80); - write_short_reg(devrec, REG_CCAEDTH, 0x60); - write_short_reg(devrec, REG_BBREG6, 0x40); - write_short_reg(devrec, REG_RFCTL, 0x04); - write_short_reg(devrec, REG_RFCTL, 0x0); - udelay(192); + mrf24j40_phy_setup(devrec); - /* Set RX Mode. RXMCR<1:0>: 0x0 normal, 0x1 promisc, 0x2 error */ - ret = read_short_reg(devrec, REG_RXMCR, &val); - if (ret) - goto err_read_reg; - val &= ~0x3; /* Clear RX mode (normal) */ - write_short_reg(devrec, REG_RXMCR, val); - - ret = request_irq(spi->irq, - mrf24j40_isr, - IRQF_TRIGGER_FALLING, - dev_name(&spi->dev), - devrec); + /* request IRQF_TRIGGER_LOW as fallback default */ + irq_type = irq_get_trigger_type(spi->irq); + if (!irq_type) + irq_type = IRQF_TRIGGER_LOW; + ret = devm_request_irq(&spi->dev, spi->irq, mrf24j40_isr, + irq_type, dev_name(&spi->dev), devrec); if (ret) { dev_err(printdev(devrec), "Unable to get IRQ"); - goto err_irq; + goto err_register_device; } + dev_dbg(printdev(devrec), "registered mrf24j40\n"); + ret = ieee802154_register_hw(devrec->hw); + if (ret) + goto err_register_device; + return 0; -err_irq: -err_read_reg: - ieee802154_unregister_device(devrec->dev); err_register_device: - ieee802154_free_device(devrec->dev); -err_alloc_dev: - kfree(devrec->buf); -err_buf: - kfree(devrec); -err_devrec: + ieee802154_free_hw(devrec->hw); +err_ret: return ret; } @@ -727,32 +1354,34 @@ dev_dbg(printdev(devrec), "remove\n"); - free_irq(spi->irq, devrec); - flush_work(&devrec->irqwork); /* TODO: Is this the right call? */ - ieee802154_unregister_device(devrec->dev); - ieee802154_free_device(devrec->dev); + ieee802154_unregister_hw(devrec->hw); + ieee802154_free_hw(devrec->hw); /* TODO: Will ieee802154_free_device() wait until ->xmit() is * complete? */ - /* Clean up the SPI stuff. */ - spi_set_drvdata(spi, NULL); - kfree(devrec->buf); - kfree(devrec); return 0; } +static const struct of_device_id mrf24j40_of_match[] = { + { .compatible = "microchip,mrf24j40", .data = (void *)MRF24J40 }, + { .compatible = "microchip,mrf24j40ma", .data = (void *)MRF24J40MA }, + { .compatible = "microchip,mrf24j40mc", .data = (void *)MRF24J40MC }, + { }, +}; +MODULE_DEVICE_TABLE(of, mrf24j40_of_match); + static const struct spi_device_id mrf24j40_ids[] = { - { "mrf24j40", 0 }, - { "mrf24j40ma", 0 }, + { "mrf24j40", MRF24J40 }, + { "mrf24j40ma", MRF24J40MA }, + { "mrf24j40mc", MRF24J40MC }, { }, }; MODULE_DEVICE_TABLE(spi, mrf24j40_ids); static struct spi_driver mrf24j40_driver = { .driver = { + .of_match_table = of_match_ptr(mrf24j40_of_match), .name = "mrf24j40", - .bus = &spi_bus_type, - .owner = THIS_MODULE, }, .id_table = mrf24j40_ids, .probe = mrf24j40_probe,