--- zzzz-none-000/linux-3.10.107/drivers/net/phy/marvell.c 2017-06-27 09:49:32.000000000 +0000 +++ scorpion-7490-727/linux-3.10.107/drivers/net/phy/marvell.c 2021-02-04 17:41:59.000000000 +0000 @@ -34,9 +34,9 @@ #include #include -#include +#include #include -#include +#include #define MII_MARVELL_PHY_PAGE 22 @@ -48,11 +48,22 @@ #define MII_M1011_IMASK_CLEAR 0x0000 #define MII_M1011_PHY_SCR 0x10 +#define MII_M1011_PHY_SCR_MDI 0x0000 +#define MII_M1011_PHY_SCR_MDI_X 0x0020 #define MII_M1011_PHY_SCR_AUTO_CROSS 0x0060 +#define MII_M1145_PHY_EXT_ADDR_PAGE 0x16 +#define MII_M1145_PHY_EXT_SR 0x1b #define MII_M1145_PHY_EXT_CR 0x14 #define MII_M1145_RGMII_RX_DELAY 0x0080 #define MII_M1145_RGMII_TX_DELAY 0x0002 +#define MII_M1145_HWCFG_MODE_SGMII_NO_CLK 0x4 +#define MII_M1145_HWCFG_MODE_MASK 0xf +#define MII_M1145_HWCFG_FIBER_COPPER_AUTO 0x8000 + +#define MII_M1145_HWCFG_MODE_SGMII_NO_CLK 0x4 +#define MII_M1145_HWCFG_MODE_MASK 0xf +#define MII_M1145_HWCFG_FIBER_COPPER_AUTO 0x8000 #define MII_M1111_PHY_LED_CONTROL 0x18 #define MII_M1111_PHY_LED_DIRECT 0x4100 @@ -116,6 +127,11 @@ #define MII_M1011_PHY_STATUS_RESOLVED 0x0800 #define MII_M1011_PHY_STATUS_LINK 0x0400 +#define MII_M1116R_CONTROL_REG_MAC 21 + +#define MII_88E3016_PHY_SPEC_CTRL 0x10 +#define MII_88E3016_DISABLE_SCRAMBLER 0x0200 +#define MII_88E3016_AUTO_MDIX_CROSSOVER 0x0030 MODULE_DESCRIPTION("Marvell PHY driver"); MODULE_AUTHOR("Andy Fleming"); @@ -146,6 +162,43 @@ return err; } +static int marvell_set_polarity(struct phy_device *phydev, int polarity) +{ + int reg; + int err; + int val; + + /* get the current settings */ + reg = phy_read(phydev, MII_M1011_PHY_SCR); + if (reg < 0) + return reg; + + val = reg; + val &= ~MII_M1011_PHY_SCR_AUTO_CROSS; + switch (polarity) { + case ETH_TP_MDI: + val |= MII_M1011_PHY_SCR_MDI; + break; + case ETH_TP_MDI_X: + val |= MII_M1011_PHY_SCR_MDI_X; + break; + case ETH_TP_MDI_AUTO: + case ETH_TP_MDI_INVALID: + default: + val |= MII_M1011_PHY_SCR_AUTO_CROSS; + break; + } + + if (val != reg) { + /* Set the new polarity value in the register */ + err = phy_write(phydev, MII_M1011_PHY_SCR, val); + if (err) + return err; + } + + return 0; +} + static int marvell_config_aneg(struct phy_device *phydev) { int err; @@ -178,8 +231,7 @@ if (err < 0) return err; - err = phy_write(phydev, MII_M1011_PHY_SCR, - MII_M1011_PHY_SCR_AUTO_CROSS); + err = marvell_set_polarity(phydev, phydev->mdix); if (err < 0) return err; @@ -304,10 +356,7 @@ if (err < 0) return err; - if ((phydev->interface == PHY_INTERFACE_MODE_RGMII) || - (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID) || - (phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID) || - (phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID)) { + if (phy_interface_is_rgmii(phydev)) { mscr = phy_read(phydev, MII_88E1121_PHY_MSCR_REG) & MII_88E1121_PHY_MSCR_DELAY_MASK; @@ -372,15 +421,91 @@ return m88e1121_config_aneg(phydev); } +static int m88e1510_config_aneg(struct phy_device *phydev) +{ + int err; + + err = m88e1318_config_aneg(phydev); + if (err < 0) + return err; + + return marvell_of_reg_init(phydev); +} + +static int m88e1116r_config_init(struct phy_device *phydev) +{ + int temp; + int err; + + temp = phy_read(phydev, MII_BMCR); + temp |= BMCR_RESET; + err = phy_write(phydev, MII_BMCR, temp); + if (err < 0) + return err; + + mdelay(500); + + err = phy_write(phydev, MII_MARVELL_PHY_PAGE, 0); + if (err < 0) + return err; + + temp = phy_read(phydev, MII_M1011_PHY_SCR); + temp |= (7 << 12); /* max number of gigabit attempts */ + temp |= (1 << 11); /* enable downshift */ + temp |= MII_M1011_PHY_SCR_AUTO_CROSS; + err = phy_write(phydev, MII_M1011_PHY_SCR, temp); + if (err < 0) + return err; + + err = phy_write(phydev, MII_MARVELL_PHY_PAGE, 2); + if (err < 0) + return err; + temp = phy_read(phydev, MII_M1116R_CONTROL_REG_MAC); + temp |= (1 << 5); + temp |= (1 << 4); + err = phy_write(phydev, MII_M1116R_CONTROL_REG_MAC, temp); + if (err < 0) + return err; + err = phy_write(phydev, MII_MARVELL_PHY_PAGE, 0); + if (err < 0) + return err; + + temp = phy_read(phydev, MII_BMCR); + temp |= BMCR_RESET; + err = phy_write(phydev, MII_BMCR, temp); + if (err < 0) + return err; + + mdelay(500); + + return 0; +} + +static int m88e3016_config_init(struct phy_device *phydev) +{ + int reg; + + /* Enable Scrambler and Auto-Crossover */ + reg = phy_read(phydev, MII_88E3016_PHY_SPEC_CTRL); + if (reg < 0) + return reg; + + reg &= ~MII_88E3016_DISABLE_SCRAMBLER; + reg |= MII_88E3016_AUTO_MDIX_CROSSOVER; + + reg = phy_write(phydev, MII_88E3016_PHY_SPEC_CTRL, reg); + if (reg < 0) + return reg; + + return 0; +} + static int m88e1111_config_init(struct phy_device *phydev) { int err; int temp; - if ((phydev->interface == PHY_INTERFACE_MODE_RGMII) || - (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID) || - (phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID) || - (phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID)) { + if (phy_interface_is_rgmii(phydev)) { temp = phy_read(phydev, MII_M1111_PHY_EXT_CR); if (temp < 0) @@ -428,6 +553,16 @@ err = phy_write(phydev, MII_M1111_PHY_EXT_SR, temp); if (err < 0) return err; + + /* make sure copper is selected */ + err = phy_read(phydev, MII_M1145_PHY_EXT_ADDR_PAGE); + if (err < 0) + return err; + + err = phy_write(phydev, MII_M1145_PHY_EXT_ADDR_PAGE, + err & (~0xff)); + if (err < 0) + return err; } if (phydev->interface == PHY_INTERFACE_MODE_RTBI) { @@ -558,6 +693,7 @@ static int m88e1145_config_init(struct phy_device *phydev) { int err; + int temp; /* Take care of errata E0 & E1 */ err = phy_write(phydev, 0x1d, 0x001b); @@ -614,6 +750,20 @@ } } + if (phydev->interface == PHY_INTERFACE_MODE_SGMII) { + temp = phy_read(phydev, MII_M1145_PHY_EXT_SR); + if (temp < 0) + return temp; + + temp &= ~MII_M1145_HWCFG_MODE_MASK; + temp |= MII_M1145_HWCFG_MODE_SGMII_NO_CLK; + temp |= MII_M1145_HWCFG_FIBER_COPPER_AUTO; + + err = phy_write(phydev, MII_M1145_PHY_EXT_SR, temp); + if (err < 0) + return err; + } + err = marvell_of_reg_init(phydev); if (err < 0) return err; @@ -635,6 +785,7 @@ int adv; int err; int lpa; + int lpagb; int status = 0; /* Update the link, but return if there @@ -652,10 +803,17 @@ if (lpa < 0) return lpa; + lpagb = phy_read(phydev, MII_STAT1000); + if (lpagb < 0) + return lpagb; + adv = phy_read(phydev, MII_ADVERTISE); if (adv < 0) return adv; + phydev->lp_advertising = mii_stat1000_to_ethtool_lpa_t(lpagb) | + mii_lpa_to_ethtool_lpa_t(lpa); + lpa &= adv; if (status & MII_M1011_PHY_STATUS_FULLDUPLEX) @@ -703,11 +861,18 @@ phydev->speed = SPEED_10; phydev->pause = phydev->asym_pause = 0; + phydev->lp_advertising = 0; } return 0; } +static int marvell_aneg_done(struct phy_device *phydev) +{ + int retval = phy_read(phydev, MII_M1011_PHY_STATUS); + return (retval < 0) ? retval : (retval & MII_M1011_PHY_STATUS_RESOLVED); +} + static int m88e1121_did_interrupt(struct phy_device *phydev) { int imask; @@ -832,6 +997,8 @@ .read_status = &genphy_read_status, .ack_interrupt = &marvell_ack_interrupt, .config_intr = &marvell_config_intr, + .resume = &genphy_resume, + .suspend = &genphy_suspend, .driver = { .owner = THIS_MODULE }, }, { @@ -845,6 +1012,8 @@ .read_status = &genphy_read_status, .ack_interrupt = &marvell_ack_interrupt, .config_intr = &marvell_config_intr, + .resume = &genphy_resume, + .suspend = &genphy_suspend, .driver = { .owner = THIS_MODULE }, }, { @@ -858,6 +1027,8 @@ .read_status = &marvell_read_status, .ack_interrupt = &marvell_ack_interrupt, .config_intr = &marvell_config_intr, + .resume = &genphy_resume, + .suspend = &genphy_suspend, .driver = { .owner = THIS_MODULE }, }, { @@ -871,6 +1042,8 @@ .read_status = &genphy_read_status, .ack_interrupt = &marvell_ack_interrupt, .config_intr = &marvell_config_intr, + .resume = &genphy_resume, + .suspend = &genphy_suspend, .driver = {.owner = THIS_MODULE,}, }, { @@ -884,6 +1057,8 @@ .ack_interrupt = &marvell_ack_interrupt, .config_intr = &marvell_config_intr, .did_interrupt = &m88e1121_did_interrupt, + .resume = &genphy_resume, + .suspend = &genphy_suspend, .driver = { .owner = THIS_MODULE }, }, { @@ -899,6 +1074,8 @@ .did_interrupt = &m88e1121_did_interrupt, .get_wol = &m88e1318_get_wol, .set_wol = &m88e1318_set_wol, + .resume = &genphy_resume, + .suspend = &genphy_suspend, .driver = { .owner = THIS_MODULE }, }, { @@ -912,6 +1089,8 @@ .read_status = &genphy_read_status, .ack_interrupt = &marvell_ack_interrupt, .config_intr = &marvell_config_intr, + .resume = &genphy_resume, + .suspend = &genphy_suspend, .driver = { .owner = THIS_MODULE }, }, { @@ -925,6 +1104,8 @@ .read_status = &genphy_read_status, .ack_interrupt = &marvell_ack_interrupt, .config_intr = &marvell_config_intr, + .resume = &genphy_resume, + .suspend = &genphy_suspend, .driver = { .owner = THIS_MODULE }, }, { @@ -938,35 +1119,90 @@ .read_status = &genphy_read_status, .ack_interrupt = &marvell_ack_interrupt, .config_intr = &marvell_config_intr, + .resume = &genphy_resume, + .suspend = &genphy_suspend, + .driver = { .owner = THIS_MODULE }, + }, + { + .phy_id = MARVELL_PHY_ID_88E1116R, + .phy_id_mask = MARVELL_PHY_ID_MASK, + .name = "Marvell 88E1116R", + .features = PHY_GBIT_FEATURES, + .flags = PHY_HAS_INTERRUPT, + .config_init = &m88e1116r_config_init, + .config_aneg = &genphy_config_aneg, + .read_status = &genphy_read_status, + .ack_interrupt = &marvell_ack_interrupt, + .config_intr = &marvell_config_intr, + .resume = &genphy_resume, + .suspend = &genphy_suspend, + .driver = { .owner = THIS_MODULE }, + }, + { + .phy_id = MARVELL_PHY_ID_88E1510, + .phy_id_mask = MARVELL_PHY_ID_MASK, + .name = "Marvell 88E1510", + .features = PHY_GBIT_FEATURES, + .flags = PHY_HAS_INTERRUPT, + .config_aneg = &m88e1510_config_aneg, + .read_status = &marvell_read_status, + .ack_interrupt = &marvell_ack_interrupt, + .config_intr = &marvell_config_intr, + .did_interrupt = &m88e1121_did_interrupt, + .resume = &genphy_resume, + .suspend = &genphy_suspend, + .driver = { .owner = THIS_MODULE }, + }, + { + .phy_id = MARVELL_PHY_ID_88E1540, + .phy_id_mask = MARVELL_PHY_ID_MASK, + .name = "Marvell 88E1540", + .features = PHY_GBIT_FEATURES, + .flags = PHY_HAS_INTERRUPT, + .config_aneg = &m88e1510_config_aneg, + .read_status = &marvell_read_status, + .ack_interrupt = &marvell_ack_interrupt, + .config_intr = &marvell_config_intr, + .did_interrupt = &m88e1121_did_interrupt, + .resume = &genphy_resume, + .suspend = &genphy_suspend, + .driver = { .owner = THIS_MODULE }, + }, + { + .phy_id = MARVELL_PHY_ID_88E3016, + .phy_id_mask = MARVELL_PHY_ID_MASK, + .name = "Marvell 88E3016", + .features = PHY_BASIC_FEATURES, + .flags = PHY_HAS_INTERRUPT, + .config_aneg = &genphy_config_aneg, + .config_init = &m88e3016_config_init, + .aneg_done = &marvell_aneg_done, + .read_status = &marvell_read_status, + .ack_interrupt = &marvell_ack_interrupt, + .config_intr = &marvell_config_intr, + .did_interrupt = &m88e1121_did_interrupt, + .resume = &genphy_resume, + .suspend = &genphy_suspend, .driver = { .owner = THIS_MODULE }, }, }; -static int __init marvell_init(void) -{ - return phy_drivers_register(marvell_drivers, - ARRAY_SIZE(marvell_drivers)); -} - -static void __exit marvell_exit(void) -{ - phy_drivers_unregister(marvell_drivers, - ARRAY_SIZE(marvell_drivers)); -} - -module_init(marvell_init); -module_exit(marvell_exit); +module_phy_driver(marvell_drivers); static struct mdio_device_id __maybe_unused marvell_tbl[] = { - { 0x01410c60, 0xfffffff0 }, - { 0x01410c90, 0xfffffff0 }, - { 0x01410cc0, 0xfffffff0 }, - { 0x01410e10, 0xfffffff0 }, - { 0x01410cb0, 0xfffffff0 }, - { 0x01410cd0, 0xfffffff0 }, - { 0x01410e50, 0xfffffff0 }, - { 0x01410e30, 0xfffffff0 }, - { 0x01410e90, 0xfffffff0 }, + { MARVELL_PHY_ID_88E1101, MARVELL_PHY_ID_MASK }, + { MARVELL_PHY_ID_88E1112, MARVELL_PHY_ID_MASK }, + { MARVELL_PHY_ID_88E1111, MARVELL_PHY_ID_MASK }, + { MARVELL_PHY_ID_88E1118, MARVELL_PHY_ID_MASK }, + { MARVELL_PHY_ID_88E1121R, MARVELL_PHY_ID_MASK }, + { MARVELL_PHY_ID_88E1145, MARVELL_PHY_ID_MASK }, + { MARVELL_PHY_ID_88E1149R, MARVELL_PHY_ID_MASK }, + { MARVELL_PHY_ID_88E1240, MARVELL_PHY_ID_MASK }, + { MARVELL_PHY_ID_88E1318S, MARVELL_PHY_ID_MASK }, + { MARVELL_PHY_ID_88E1116R, MARVELL_PHY_ID_MASK }, + { MARVELL_PHY_ID_88E1510, MARVELL_PHY_ID_MASK }, + { MARVELL_PHY_ID_88E1540, MARVELL_PHY_ID_MASK }, + { MARVELL_PHY_ID_88E3016, MARVELL_PHY_ID_MASK }, { } };