--- zzzz-none-000/linux-3.10.107/drivers/net/phy/smsc.c	2017-06-27 09:49:32.000000000 +0000
+++ scorpion-7490-727/linux-3.10.107/drivers/net/phy/smsc.c	2021-02-04 17:41:59.000000000 +0000
@@ -43,6 +43,31 @@
 
 static int smsc_phy_config_init(struct phy_device *phydev)
 {
+	int __maybe_unused len;
+	struct device *dev __maybe_unused = &phydev->dev;
+	struct device_node *of_node __maybe_unused = dev->of_node;
+	int rc = phy_read(phydev, MII_LAN83C185_CTRL_STATUS);
+	int enable_energy = 1;
+
+	if (rc < 0)
+		return rc;
+
+	if (of_find_property(of_node, "smsc,disable-energy-detect", &len))
+		enable_energy = 0;
+
+	if (enable_energy) {
+		/* Enable energy detect mode for this SMSC Transceivers */
+		rc = phy_write(phydev, MII_LAN83C185_CTRL_STATUS,
+			       rc | MII_LAN83C185_EDPWRDOWN);
+		if (rc < 0)
+			return rc;
+	}
+
+	return smsc_phy_ack_interrupt(phydev);
+}
+
+static int smsc_phy_reset(struct phy_device *phydev)
+{
 	int rc = phy_read(phydev, MII_LAN83C185_SPECIAL_MODES);
 	if (rc < 0)
 		return rc;
@@ -66,18 +91,7 @@
 			rc = phy_read(phydev, MII_BMCR);
 		} while (rc & BMCR_RESET);
 	}
-
-	rc = phy_read(phydev, MII_LAN83C185_CTRL_STATUS);
-	if (rc < 0)
-		return rc;
-
-	/* Enable energy detect mode for this SMSC Transceivers */
-	rc = phy_write(phydev, MII_LAN83C185_CTRL_STATUS,
-		       rc | MII_LAN83C185_EDPWRDOWN);
-	if (rc < 0)
-		return rc;
-
-	return smsc_phy_ack_interrupt (phydev);
+	return 0;
 }
 
 static int lan911x_config_init(struct phy_device *phydev)
@@ -86,19 +100,18 @@
 }
 
 /*
- * The LAN8710/LAN8720 requires a minimum of 2 link pulses within 64ms of each
- * other in order to set the ENERGYON bit and exit EDPD mode.  If a link partner
- * does send the pulses within this interval, the PHY will remained powered
- * down.
- *
- * This workaround will manually toggle the PHY on/off upon calls to read_status
- * in order to generate link test pulses if the link is down.  If a link partner
- * is present, it will respond to the pulses, which will cause the ENERGYON bit
- * to be set and will cause the EDPD mode to be exited.
+ * The LAN87xx suffers from rare absence of the ENERGYON-bit when Ethernet cable
+ * plugs in while LAN87xx is in Energy Detect Power-Down mode. This leads to
+ * unstable detection of plugging in Ethernet cable.
+ * This workaround disables Energy Detect Power-Down mode and waiting for
+ * response on link pulses to detect presence of plugged Ethernet cable.
+ * The Energy Detect Power-Down mode is enabled again in the end of procedure to
+ * save approximately 220 mW of power if cable is unplugged.
  */
 static int lan87xx_read_status(struct phy_device *phydev)
 {
 	int err = genphy_read_status(phydev);
+	int i;
 
 	if (!phydev->link) {
 		/* Disable EDPD to wake up PHY */
@@ -111,8 +124,16 @@
 		if (rc < 0)
 			return rc;
 
-		/* Sleep 64 ms to allow ~5 link test pulses to be sent */
-		msleep(64);
+		/* Wait max 640 ms to detect energy */
+		for (i = 0; i < 64; i++) {
+			/* Sleep to allow link test pulses to be sent */
+			msleep(10);
+			rc = phy_read(phydev, MII_LAN83C185_CTRL_STATUS);
+			if (rc < 0)
+				return rc;
+			if (rc & MII_LAN83C185_ENERGYON)
+				break;
+		}
 
 		/* Re-enable EDPD */
 		rc = phy_read(phydev, MII_LAN83C185_CTRL_STATUS);
@@ -142,6 +163,7 @@
 	.config_aneg	= genphy_config_aneg,
 	.read_status	= genphy_read_status,
 	.config_init	= smsc_phy_config_init,
+	.soft_reset	= smsc_phy_reset,
 
 	/* IRQ related */
 	.ack_interrupt	= smsc_phy_ack_interrupt,
@@ -164,6 +186,7 @@
 	.config_aneg	= genphy_config_aneg,
 	.read_status	= genphy_read_status,
 	.config_init	= smsc_phy_config_init,
+	.soft_reset	= smsc_phy_reset,
 
 	/* IRQ related */
 	.ack_interrupt	= smsc_phy_ack_interrupt,
@@ -184,8 +207,9 @@
 
 	/* basic functions */
 	.config_aneg	= genphy_config_aneg,
-	.read_status	= genphy_read_status,
+	.read_status	= lan87xx_read_status,
 	.config_init	= smsc_phy_config_init,
+	.soft_reset	= smsc_phy_reset,
 
 	/* IRQ related */
 	.ack_interrupt	= smsc_phy_ack_interrupt,
@@ -230,6 +254,7 @@
 	.config_aneg	= genphy_config_aneg,
 	.read_status	= lan87xx_read_status,
 	.config_init	= smsc_phy_config_init,
+	.soft_reset	= smsc_phy_reset,
 
 	/* IRQ related */
 	.ack_interrupt	= smsc_phy_ack_interrupt,
@@ -241,25 +266,12 @@
 	.driver		= { .owner = THIS_MODULE, }
 } };
 
-static int __init smsc_init(void)
-{
-	return phy_drivers_register(smsc_phy_driver,
-		ARRAY_SIZE(smsc_phy_driver));
-}
-
-static void __exit smsc_exit(void)
-{
-	return phy_drivers_unregister(smsc_phy_driver,
-		ARRAY_SIZE(smsc_phy_driver));
-}
+module_phy_driver(smsc_phy_driver);
 
 MODULE_DESCRIPTION("SMSC PHY driver");
 MODULE_AUTHOR("Herbert Valerio Riedel");
 MODULE_LICENSE("GPL");
 
-module_init(smsc_init);
-module_exit(smsc_exit);
-
 static struct mdio_device_id __maybe_unused smsc_tbl[] = {
 	{ 0x0007c0a0, 0xfffffff0 },
 	{ 0x0007c0b0, 0xfffffff0 },