--- zzzz-none-000/linux-3.10.107/drivers/net/wireless/iwlwifi/mvm/fw-api-tx.h 2017-06-27 09:49:32.000000000 +0000 +++ scorpion-7490-727/linux-3.10.107/drivers/net/wireless/iwlwifi/mvm/fw-api-tx.h 2021-02-04 17:41:59.000000000 +0000 @@ -5,7 +5,7 @@ * * GPL LICENSE SUMMARY * - * Copyright(c) 2012 - 2013 Intel Corporation. All rights reserved. + * Copyright(c) 2012 - 2014 Intel Corporation. All rights reserved. * * This program is free software; you can redistribute it and/or modify * it under the terms of version 2 of the GNU General Public License as @@ -30,7 +30,7 @@ * * BSD LICENSE * - * Copyright(c) 2012 - 2013 Intel Corporation. All rights reserved. + * Copyright(c) 2012 - 2014 Intel Corporation. All rights reserved. * All rights reserved. * * Redistribution and use in source and binary forms, with or without @@ -66,32 +66,30 @@ /** * enum iwl_tx_flags - bitmasks for tx_flags in TX command * @TX_CMD_FLG_PROT_REQUIRE: use RTS or CTS-to-self to protect the frame + * @TX_CMD_FLG_WRITE_TX_POWER: update current tx power value in the mgmt frame * @TX_CMD_FLG_ACK: expect ACK from receiving station * @TX_CMD_FLG_STA_RATE: use RS table with initial index from the TX command. * Otherwise, use rate_n_flags from the TX command - * @TX_CMD_FLG_BA: this frame is a block ack * @TX_CMD_FLG_BAR: this frame is a BA request, immediate BAR is expected * Must set TX_CMD_FLG_ACK with this flag. - * @TX_CMD_FLG_TXOP_PROT: protect frame with full TXOP protection * @TX_CMD_FLG_VHT_NDPA: mark frame is NDPA for VHT beamformer sequence * @TX_CMD_FLG_HT_NDPA: mark frame is NDPA for HT beamformer sequence * @TX_CMD_FLG_CSI_FDBK2HOST: mark to send feedback to host (only if good CRC) + * @TX_CMD_FLG_BT_PRIO_POS: the position of the BT priority (bit 11 is ignored + * on old firmwares). * @TX_CMD_FLG_BT_DIS: disable BT priority for this frame * @TX_CMD_FLG_SEQ_CTL: set if FW should override the sequence control. * Should be set for mgmt, non-QOS data, mcast, bcast and in scan command * @TX_CMD_FLG_MORE_FRAG: this frame is non-last MPDU - * @TX_CMD_FLG_NEXT_FRAME: this frame includes information of the next frame * @TX_CMD_FLG_TSF: FW should calculate and insert TSF in the frame * Should be set for beacons and probe responses * @TX_CMD_FLG_CALIB: activate PA TX power calibrations * @TX_CMD_FLG_KEEP_SEQ_CTL: if seq_ctl is set, don't increase inner seq count - * @TX_CMD_FLG_AGG_START: allow this frame to start aggregation * @TX_CMD_FLG_MH_PAD: driver inserted 2 byte padding after MAC header. * Should be set for 26/30 length MAC headers * @TX_CMD_FLG_RESP_TO_DRV: zero this if the response should go only to FW * @TX_CMD_FLG_CCMP_AGG: this frame uses CCMP for aggregation acceleration * @TX_CMD_FLG_TKIP_MIC_DONE: FW already performed TKIP MIC calculation - * @TX_CMD_FLG_CTS_ONLY: send CTS only, no data after that * @TX_CMD_FLG_DUR: disable duration overwriting used in PS-Poll Assoc-id * @TX_CMD_FLG_FW_DROP: FW should mark frame to be dropped * @TX_CMD_FLG_EXEC_PAPD: execute PAPD @@ -100,27 +98,25 @@ */ enum iwl_tx_flags { TX_CMD_FLG_PROT_REQUIRE = BIT(0), + TX_CMD_FLG_WRITE_TX_POWER = BIT(1), TX_CMD_FLG_ACK = BIT(3), TX_CMD_FLG_STA_RATE = BIT(4), - TX_CMD_FLG_BA = BIT(5), TX_CMD_FLG_BAR = BIT(6), TX_CMD_FLG_TXOP_PROT = BIT(7), TX_CMD_FLG_VHT_NDPA = BIT(8), TX_CMD_FLG_HT_NDPA = BIT(9), TX_CMD_FLG_CSI_FDBK2HOST = BIT(10), + TX_CMD_FLG_BT_PRIO_POS = 11, TX_CMD_FLG_BT_DIS = BIT(12), TX_CMD_FLG_SEQ_CTL = BIT(13), TX_CMD_FLG_MORE_FRAG = BIT(14), - TX_CMD_FLG_NEXT_FRAME = BIT(15), TX_CMD_FLG_TSF = BIT(16), TX_CMD_FLG_CALIB = BIT(17), TX_CMD_FLG_KEEP_SEQ_CTL = BIT(18), - TX_CMD_FLG_AGG_START = BIT(19), TX_CMD_FLG_MH_PAD = BIT(20), TX_CMD_FLG_RESP_TO_DRV = BIT(21), TX_CMD_FLG_CCMP_AGG = BIT(22), TX_CMD_FLG_TKIP_MIC_DONE = BIT(23), - TX_CMD_FLG_CTS_ONLY = BIT(24), TX_CMD_FLG_DUR = BIT(25), TX_CMD_FLG_FW_DROP = BIT(26), TX_CMD_FLG_EXEC_PAPD = BIT(27), @@ -128,12 +124,26 @@ TX_CMD_FLG_HCCA_CHUNK = BIT(31) }; /* TX_FLAGS_BITS_API_S_VER_1 */ +/** + * enum iwl_tx_pm_timeouts - pm timeout values in TX command + * @PM_FRAME_NONE: no need to suspend sleep mode + * @PM_FRAME_MGMT: fw suspend sleep mode for 100TU + * @PM_FRAME_ASSOC: fw suspend sleep mode for 10sec + */ +enum iwl_tx_pm_timeouts { + PM_FRAME_NONE = 0, + PM_FRAME_MGMT = 2, + PM_FRAME_ASSOC = 3, +}; + /* * TX command security control */ #define TX_CMD_SEC_WEP 0x01 #define TX_CMD_SEC_CCM 0x02 #define TX_CMD_SEC_TKIP 0x03 +#define TX_CMD_SEC_EXT 0x04 +#define TX_CMD_SEC_MSK 0x07 #define TX_CMD_SEC_WEP_KEY_IDX_POS 6 #define TX_CMD_SEC_WEP_KEY_IDX_MSK 0xc0 #define TX_CMD_SEC_KEY128 0x08 @@ -188,8 +198,6 @@ * struct iwl_tx_cmd - TX command struct to FW * ( TX_CMD = 0x1c ) * @len: in bytes of the payload, see below for details - * @next_frame_len: same as len, but for next frame (0 if not applicable) - * Used for fragmentation and bursting, but not in 11n aggregation. * @tx_flags: combination of TX_CMD_FLG_* * @rate_n_flags: rate for *all* Tx attempts, if TX_CMD_FLG_STA_RATE_MSK is * cleared. Combination of RATE_MCS_* @@ -207,8 +215,6 @@ * @data_retry_limit: max attempts to send the data packet * @tid_spec: TID/tspec * @pm_frame_timeout: PM TX frame timeout - * @driver_txop: duration od EDCA TXOP, in 32-usec units. Set this if not - * specified by HCCA protocol * * The byte count (both len and next_frame_len) includes MAC header * (24/26/30/32 bytes) @@ -227,18 +233,18 @@ __le16 len; __le16 next_frame_len; __le32 tx_flags; - /* DRAM_SCRATCH_API_U_VER_1 */ - u8 try_cnt; - u8 btkill_cnt; - __le16 reserved; + struct { + u8 try_cnt; + u8 btkill_cnt; + __le16 reserved; + } scratch; /* DRAM_SCRATCH_API_U_VER_1 */ __le32 rate_n_flags; u8 sta_id; u8 sec_ctl; u8 initial_rate_index; u8 reserved2; u8 key[16]; - __le16 next_frame_flags; - __le16 reserved3; + __le32 reserved3; __le32 life_time; __le32 dram_lsb_ptr; u8 dram_msb_ptr; @@ -246,7 +252,7 @@ u8 data_retry_limit; u8 tid_tspec; __le16 pm_frame_timeout; - __le16 driver_txop; + __le16 reserved4; u8 payload[0]; struct ieee80211_hdr hdr[0]; } __packed; /* TX_CMD_API_S_VER_3 */ @@ -478,7 +484,8 @@ u8 pa_integ_res_b[3]; u8 pa_integ_res_c[3]; __le16 measurement_req_id; - __le16 reserved; + u8 reduced_tpc; + u8 reserved; __le32 tfd_info; __le16 seq_ctl; @@ -544,6 +551,20 @@ } __packed; /** + * struct iwl_extended_beacon_notif - notifies about beacon transmission + * @beacon_notify_hdr: tx response command associated with the beacon + * @tsf: last beacon tsf + * @ibss_mgr_status: whether IBSS is manager + * @gp2: last beacon time in gp2 + */ +struct iwl_extended_beacon_notif { + struct iwl_mvm_tx_resp beacon_notify_hdr; + __le64 tsf; + __le32 ibss_mgr_status; + __le32 gp2; +} __packed; /* BEACON_NTFY_API_S_VER_5 */ + +/** * enum iwl_dump_control - dump (flush) control flags * @DUMP_TX_FIFO_FLUSH: Dump MSDUs until the the FIFO is empty * and the TFD queues are empty. @@ -583,4 +604,43 @@ tx_resp->frame_count) & 0xfff; } +/** + * struct iwl_scd_txq_cfg_cmd - New txq hw scheduler config command + * @token: + * @sta_id: station id + * @tid: + * @scd_queue: scheduler queue to confiug + * @enable: 1 queue enable, 0 queue disable + * @aggregate: 1 aggregated queue, 0 otherwise + * @tx_fifo: %enum iwl_mvm_tx_fifo + * @window: BA window size + * @ssn: SSN for the BA agreement + */ +struct iwl_scd_txq_cfg_cmd { + u8 token; + u8 sta_id; + u8 tid; + u8 scd_queue; + u8 enable; + u8 aggregate; + u8 tx_fifo; + u8 window; + __le16 ssn; + __le16 reserved; +} __packed; /* SCD_QUEUE_CFG_CMD_API_S_VER_1 */ + +/** + * struct iwl_scd_txq_cfg_rsp + * @token: taken from the command + * @sta_id: station id from the command + * @tid: tid from the command + * @scd_queue: scd_queue from the command + */ +struct iwl_scd_txq_cfg_rsp { + u8 token; + u8 sta_id; + u8 tid; + u8 scd_queue; +} __packed; /* SCD_QUEUE_CFG_RSP_API_S_VER_1 */ + #endif /* __fw_api_tx_h__ */