--- zzzz-none-000/linux-3.10.107/drivers/regulator/Kconfig 2017-06-27 09:49:32.000000000 +0000 +++ scorpion-7490-727/linux-3.10.107/drivers/regulator/Kconfig 2021-02-04 17:41:59.000000000 +0000 @@ -28,16 +28,6 @@ help Say yes here to enable debugging support. -config REGULATOR_DUMMY - bool "Provide a dummy regulator if regulator lookups fail" - help - If this option is enabled then when a regulator lookup fails - and the board has not specified that it has provided full - constraints the regulator core will provide an always - enabled dummy regulator, allowing consumer drivers to continue. - - A warning will be generated when this substitution is done. - config REGULATOR_FIXED_VOLTAGE tristate "Fixed voltage regulator support" help @@ -64,15 +54,29 @@ If unsure, say no. -config REGULATOR_GPIO - tristate "GPIO regulator support" - depends on GPIOLIB +config REGULATOR_88PM800 + tristate "Marvell 88PM800 Power regulators" + depends on MFD_88PM800 + help + This driver supports Marvell 88PM800 voltage regulator chips. + It delivers digitally programmable output, + the voltage is programmed via I2C interface. + It's suitable to support PXA988 chips to control VCC_MAIN and + various voltages. + +config REGULATOR_88PM8607 + tristate "Marvell 88PM8607 Power regulators" + depends on MFD_88PM860X=y help - This driver provides support for regulators that can be - controlled via gpios. - It is capable of supporting current and voltage regulators - and the platform has to provide a mapping of GPIO-states - to target volts/amps. + This driver supports 88PM8607 voltage regulator chips. + +config REGULATOR_ACT8865 + tristate "Active-semi act8865 voltage regulator" + depends on I2C + select REGMAP_I2C + help + This driver controls a active-semi act8865 voltage output + regulator via I2C bus. config REGULATOR_AD5398 tristate "Analog Devices AD5398/AD5821 regulators" @@ -81,6 +85,14 @@ This driver supports AD5398 and AD5821 current regulator chips. If building into module, its name is ad5398.ko. +config REGULATOR_ANATOP + tristate "Freescale i.MX on-chip ANATOP LDO regulators" + depends on MFD_SYSCON + help + Say y here to support Freescale i.MX on-chip ANATOP LDOs + regulators. It is recommended that this option be + enabled on i.MX6 platform. + config REGULATOR_AAT2870 tristate "AnalogicTech AAT2870 Regulators" depends on MFD_AAT2870_CORE @@ -88,6 +100,22 @@ If you have a AnalogicTech AAT2870 say Y to enable the regulator driver. +config REGULATOR_AB3100 + tristate "ST-Ericsson AB3100 Regulator functions" + depends on AB3100_CORE + default y if AB3100_CORE + help + These regulators correspond to functionality in the + AB3100 analog baseband dealing with power regulators + for the system. + +config REGULATOR_AB8500 + bool "ST-Ericsson AB8500 Power Regulators" + depends on AB8500_CORE + help + This driver supports the regulators found on the ST-Ericsson mixed + signal AB8500 PMIC + config REGULATOR_ARIZONA tristate "Wolfson Arizona class devices" depends on MFD_ARIZONA @@ -96,6 +124,69 @@ Support for the regulators found on Wolfson Arizona class devices. +config REGULATOR_AS3711 + tristate "AS3711 PMIC" + depends on MFD_AS3711 + help + This driver provides support for the voltage regulators on the + AS3711 PMIC + +config REGULATOR_AS3722 + tristate "AMS AS3722 PMIC Regulators" + depends on MFD_AS3722 + help + This driver provides support for the voltage regulators on the + AS3722 PMIC. This will enable support for all the software + controllable DCDC/LDO regulators. + +config REGULATOR_AXP20X + tristate "X-POWERS AXP20X PMIC Regulators" + depends on MFD_AXP20X + help + This driver provides support for the voltage regulators on the + AXP20X PMIC. + +config REGULATOR_BCM590XX + tristate "Broadcom BCM590xx PMU Regulators" + depends on MFD_BCM590XX + help + This driver provides support for the voltage regulators on the + BCM590xx PMUs. This will enable support for the software + controllable LDO/Switching regulators. + +config REGULATOR_CPR3 + bool "CPR3 regulator core support" + help + This driver supports Core Power Reduction (CPR) version 3 controllers + which are used by some Qualcomm Technologies, Inc. SoCs to + manage important voltage regulators. CPR3 controllers are capable of + monitoring several ring oscillator sensing loops simultaneously. The + CPR3 controller informs software when the silicon conditions require + the supply voltage to be increased or decreased. On certain supply + rails, the CPR3 controller is able to propagate the voltage increase + or decrease requests all the way to the PMIC without software + involvement. + +config REGULATOR_CPR3_NPU + bool "CPR3 regulator for NPU" + depends on OF && REGULATOR_CPR3 + help + This driver supports Qualcomm Technologies, Inc. NPU CPR3 + regulator Which will always operate in open loop. + +config REGULATOR_CPR4_APSS + bool "CPR4 regulator for APSS" + depends on OF && REGULATOR_CPR3 + help + This driver supports Qualcomm Technologies, Inc. APSS application + processor specific features including memory array power mux (APM) + switching, one CPR4 thread which monitor the two APSS clusters that + are both powered by a shared supply, hardware closed-loop auto + voltage stepping, voltage adjustments based on online core count, + voltage adjustments based on temperature readings, and voltage + adjustments for performance boost mode. This driver reads both initial + voltage and CPR target quotient values out of hardware fuses. + config REGULATOR_DA903X tristate "Dialog Semiconductor DA9030/DA9034 regulators" depends on PMIC_DA903X @@ -120,6 +211,58 @@ This driver can also be built as a module. If so, the module will be called da9055-regulator. +config REGULATOR_DA9062 + tristate "Dialog Semiconductor DA9062 regulators" + depends on MFD_DA9062 + help + Say y here to support the BUCKs and LDOs regulators found on + DA9062 PMICs. + + This driver can also be built as a module. If so, the module + will be called da9062-regulator. + +config REGULATOR_DA9063 + tristate "Dialog Semiconductor DA9063 regulators" + depends on MFD_DA9063 + help + Say y here to support the BUCKs and LDOs regulators found on + DA9063 PMICs. + + This driver can also be built as a module. If so, the module + will be called da9063-regulator. + +config REGULATOR_DA9210 + tristate "Dialog Semiconductor DA9210 regulator" + depends on I2C + select REGMAP_I2C + help + Say y here to support for the Dialog Semiconductor DA9210. + The DA9210 is a multi-phase synchronous step down + converter 12A DC-DC Buck controlled through an I2C + interface. + +config REGULATOR_DA9211 + tristate "Dialog Semiconductor DA9211/DA9212/DA9213/DA9214/DA9215 regulator" + depends on I2C + select REGMAP_I2C + help + Say y here to support for the Dialog Semiconductor DA9211/DA9212 + /DA9213/DA9214/DA9215. + The DA9211/DA9212/DA9213/DA9214/DA9215 is a multi-phase synchronous + step down converter 12A or 16A DC-DC Buck controlled through an I2C + interface. + +config REGULATOR_DBX500_PRCMU + bool + +config REGULATOR_DB8500_PRCMU + bool "ST-Ericsson DB8500 Voltage Domain Regulators" + depends on MFD_DB8500_PRCMU + select REGULATOR_DBX500_PRCMU + help + This driver supports the voltage domain regulators controlled by the + DB8500 PRCMU + config REGULATOR_FAN53555 tristate "Fairchild FAN53555 Regulator" depends on I2C @@ -131,32 +274,32 @@ input voltage supply of 2.5V to 5.5V. The output voltage is programmed through an I2C interface. -config REGULATOR_ANATOP - tristate "Freescale i.MX on-chip ANATOP LDO regulators" - depends on MFD_SYSCON +config REGULATOR_GPIO + tristate "GPIO regulator support" + depends on GPIOLIB || COMPILE_TEST help - Say y here to support Freescale i.MX on-chip ANATOP LDOs - regulators. It is recommended that this option be - enabled on i.MX6 platform. - -config REGULATOR_MC13XXX_CORE - tristate + This driver provides support for regulators that can be + controlled via gpios. + It is capable of supporting current and voltage regulators + and the platform has to provide a mapping of GPIO-states + to target volts/amps. -config REGULATOR_MC13783 - tristate "Freescale MC13783 regulator driver" - depends on MFD_MC13783 - select REGULATOR_MC13XXX_CORE +config REGULATOR_HI6421 + tristate "HiSilicon Hi6421 PMIC voltage regulator support" + depends on MFD_HI6421_PMIC && OF help - Say y here to support the regulators found on the Freescale MC13783 - PMIC. + This driver provides support for the voltage regulators on the + HiSilicon Hi6421 PMU / Codec IC. + Hi6421 is a multi-function device which, on regulator part, provides + 21 general purpose LDOs, 3 dedicated LDOs, and 5 BUCKs. All + of them come with support to either ECO (idle) or sleep mode. -config REGULATOR_MC13892 - tristate "Freescale MC13892 regulator driver" - depends on MFD_MC13XXX - select REGULATOR_MC13XXX_CORE +config REGULATOR_ISL9305 + tristate "Intersil ISL9305 regulator" + depends on I2C + select REGMAP_I2C help - Say y here to support the regulators found on the Freescale MC13892 - PMIC. + This driver supports ISL9305 voltage regulator chip. config REGULATOR_ISL6271A tristate "Intersil ISL6271A Power regulator" @@ -164,11 +307,57 @@ help This driver supports ISL6271A voltage regulator chip. -config REGULATOR_88PM8607 - bool "Marvell 88PM8607 Power regulators" - depends on MFD_88PM860X=y +config REGULATOR_LP3971 + tristate "National Semiconductors LP3971 PMIC regulator driver" + depends on I2C help - This driver supports 88PM8607 voltage regulator chips. + Say Y here to support the voltage regulators and convertors + on National Semiconductors LP3971 PMIC + +config REGULATOR_LP3972 + tristate "National Semiconductors LP3972 PMIC regulator driver" + depends on I2C + help + Say Y here to support the voltage regulators and convertors + on National Semiconductors LP3972 PMIC + +config REGULATOR_LP872X + tristate "TI/National Semiconductor LP8720/LP8725 voltage regulators" + depends on I2C + select REGMAP_I2C + help + This driver supports LP8720/LP8725 PMIC + +config REGULATOR_LP8755 + tristate "TI LP8755 High Performance PMU driver" + depends on I2C + select REGMAP_I2C + help + This driver supports LP8755 High Performance PMU driver. This + chip contains six step-down DC/DC converters which can support + 9 mode multiphase configuration. + +config REGULATOR_LP8788 + tristate "TI LP8788 Power Regulators" + depends on MFD_LP8788 + help + This driver supports LP8788 voltage regulator chip. + +config REGULATOR_LTC3589 + tristate "LTC3589 8-output voltage regulator" + depends on I2C + select REGMAP_I2C + help + This enables support for the LTC3589, LTC3589-1, and LTC3589-2 + 8-output regulators controlled via I2C. + +config REGULATOR_MAX14577 + tristate "Maxim 14577/77836 regulator" + depends on MFD_MAX14577 + help + This driver controls a Maxim MAX14577/77836 regulator via I2C bus. + The MAX14577 regulators include safeout LDO and charger current + regulator. The MAX77836 has two additional LDOs. config REGULATOR_MAX1586 tristate "Maxim 1586/1587 voltage regulator" @@ -250,48 +439,89 @@ via I2C bus. The provided regulator is suitable for Exynos-4 chips to control VARM and VINT voltages. -config REGULATOR_PCAP - tristate "Motorola PCAP2 regulator driver" - depends on EZX_PCAP - help - This driver provides support for the voltage regulators of the - PCAP2 PMIC. +config REGULATOR_MAX77693 + tristate "Maxim 77693/77843 regulator" + depends on (MFD_MAX77693 || MFD_MAX77843) + help + This driver controls a Maxim 77693/77843 regulators via I2C bus. + The regulators include two LDOs, 'SAFEOUT1', 'SAFEOUT2' + and one current regulator 'CHARGER'. This is suitable for + Exynos-4x12 (MAX77693) or Exynos5433 (MAX77843) SoC chips. -config REGULATOR_LP3971 - tristate "National Semiconductors LP3971 PMIC regulator driver" - depends on I2C +config REGULATOR_MAX77802 + tristate "Maxim 77802 regulator" + depends on MFD_MAX77686 help - Say Y here to support the voltage regulators and convertors - on National Semiconductors LP3971 PMIC + This driver controls a Maxim 77802 regulator + via I2C bus. The provided regulator is suitable for + Exynos5420/Exynos5800 SoCs to control various voltages. + It includes support for control of voltage and ramp speed. -config REGULATOR_LP3972 - tristate "National Semiconductors LP3972 PMIC regulator driver" - depends on I2C +config REGULATOR_MC13XXX_CORE + tristate + +config REGULATOR_MC13783 + tristate "Freescale MC13783 regulator driver" + depends on MFD_MC13XXX + select REGULATOR_MC13XXX_CORE help - Say Y here to support the voltage regulators and convertors - on National Semiconductors LP3972 PMIC + Say y here to support the regulators found on the Freescale MC13783 + PMIC. -config REGULATOR_LP872X - bool "TI/National Semiconductor LP8720/LP8725 voltage regulators" - depends on I2C=y - select REGMAP_I2C +config REGULATOR_MC13892 + tristate "Freescale MC13892 regulator driver" + depends on MFD_MC13XXX + select REGULATOR_MC13XXX_CORE help - This driver supports LP8720/LP8725 PMIC + Say y here to support the regulators found on the Freescale MC13892 + PMIC. -config REGULATOR_LP8755 - tristate "TI LP8755 High Performance PMU driver" +config REGULATOR_MT6311 + tristate "MediaTek MT6311 PMIC" depends on I2C select REGMAP_I2C help - This driver supports LP8755 High Performance PMU driver. This - chip contains six step-down DC/DC converters which can support - 9 mode multiphase configuration. + Say y here to select this option to enable the power regulator of + MediaTek MT6311 PMIC. + This driver supports the control of different power rails of device + through regulator interface. -config REGULATOR_LP8788 - bool "TI LP8788 Power Regulators" - depends on MFD_LP8788 +config REGULATOR_MT6397 + tristate "MediaTek MT6397 PMIC" + depends on MFD_MT6397 help - This driver supports LP8788 voltage regulator chip. + Say y here to select this option to enable the power regulator of + MediaTek MT6397 PMIC. + This driver supports the control of different power rails of device + through regulator interface. + +config REGULATOR_PALMAS + tristate "TI Palmas PMIC Regulators" + depends on MFD_PALMAS + help + If you wish to control the regulators on the Palmas series of + chips say Y here. This will enable support for all the software + controllable SMPS/LDO regulators. + + The regulators available on Palmas series chips vary depending + on the muxing. This is handled automatically in the driver by + reading the mux info from OTP. + +config REGULATOR_PBIAS + tristate "PBIAS OMAP regulator driver" + depends on (ARCH_OMAP || COMPILE_TEST) && MFD_SYSCON + help + Say y here to support pbias regulator for mmc1:SD card i/o + on OMAP SoCs. + This driver provides support for OMAP pbias modelled + regulators. + +config REGULATOR_PCAP + tristate "Motorola PCAP2 regulator driver" + depends on EZX_PCAP + help + This driver provides support for the voltage regulators of the + PCAP2 PMIC. config REGULATOR_PCF50633 tristate "NXP PCF50633 regulator driver" @@ -300,6 +530,56 @@ Say Y here to support the voltage regulators and convertors on PCF50633 +config REGULATOR_PFUZE100 + tristate "Freescale PFUZE100/PFUZE200 regulator driver" + depends on I2C + select REGMAP_I2C + help + Say y here to support the regulators found on the Freescale + PFUZE100/PFUZE200 PMIC. + +config REGULATOR_PWM + tristate "PWM voltage regulator" + depends on PWM + help + This driver supports PWM controlled voltage regulators. PWM + duty cycle can increase or decrease the voltage. + +config REGULATOR_QCOM_RPM + tristate "Qualcomm RPM regulator driver" + depends on MFD_QCOM_RPM + help + If you say yes to this option, support will be included for the + regulators exposed by the Resource Power Manager found in Qualcomm + 8660, 8960 and 8064 based devices. + + Say M here if you want to include support for the regulators on the + Qualcomm RPM as a module. The module will be named + "qcom_rpm-regulator". + +config REGULATOR_QCOM_SMD_RPM + tristate "Qualcomm SMD based RPM regulator driver" + depends on QCOM_SMD_RPM + help + If you say yes to this option, support will be included for the + regulators exposed by the Resource Power Manager found in Qualcomm + 8974 based devices. + + Say M here if you want to include support for the regulators on the + Qualcomm RPM as a module. The module will be named + "qcom_smd-regulator". + +config REGULATOR_QCOM_SPMI + tristate "Qualcomm SPMI regulator driver" + depends on SPMI || COMPILE_TEST + help + If you say yes to this option, support will be included for the + regulators found in Qualcomm SPMI PMICs. + + Say M here if you want to include support for the regulators on the + Qualcomm SPMI PMICs as a module. The module will be named + "qcom_spmi-regulator". + config REGULATOR_RC5T583 tristate "RICOH RC5T583 Power regulators" depends on MFD_RC5T583 @@ -310,13 +590,45 @@ through regulator interface. The device supports multiple DCDC/LDO outputs which can be controlled by i2c communication. +config REGULATOR_RK808 + tristate "Rockchip RK808 Power regulators" + depends on MFD_RK808 + help + Select this option to enable the power regulator of ROCKCHIP + PMIC RK808. + This driver supports the control of different power rails of device + through regulator interface. The device supports multiple DCDC/LDO + outputs which can be controlled by i2c communication. + +config REGULATOR_RN5T618 + tristate "Ricoh RN5T618 voltage regulators" + depends on MFD_RN5T618 + help + Say y here to support the regulators found on Ricoh RN5T618 PMIC. + +config REGULATOR_RT5033 + tristate "Richtek RT5033 Regulators" + depends on MFD_RT5033 + help + This adds support for voltage and current regulators in Richtek + RT5033 PMIC. The device supports multiple regulators like + current source, LDO and Buck. + +config REGULATOR_S2MPA01 + tristate "Samsung S2MPA01 voltage regulator" + depends on MFD_SEC_CORE + help + This driver controls Samsung S2MPA01 voltage output regulator + via I2C bus. S2MPA01 has 10 Bucks and 26 LDO outputs. + config REGULATOR_S2MPS11 - tristate "Samsung S2MPS11 voltage regulator" + tristate "Samsung S2MPS11/S2MPS13/S2MPS14/S2MPU02 voltage regulator" depends on MFD_SEC_CORE help - This driver supports a Samsung S2MPS11 voltage output regulator - via I2C bus. S2MPS11 is comprised of high efficient Buck converters - including Dual-Phase Buck converter, Buck-Boost converter, various LDOs. + This driver supports a Samsung S2MPS11/S2MPS13/S2MPS14/S2MPU02 voltage + output regulator via I2C bus. The chip is comprised of high efficient + Buck converters including Dual-Phase Buck converter, Buck-Boost + converter, various LDOs. config REGULATOR_S5M8767 tristate "Samsung S5M8767A voltage regulator" @@ -326,44 +638,34 @@ via I2C bus. S5M8767A have 9 Bucks and 28 LDOs output and supports DVS mode with 8bits of output voltage control. -config REGULATOR_AB3100 - tristate "ST-Ericsson AB3100 Regulator functions" - depends on AB3100_CORE - default y if AB3100_CORE - help - These regulators correspond to functionality in the - AB3100 analog baseband dealing with power regulators - for the system. - -config REGULATOR_AB8500 - bool "ST-Ericsson AB8500 Power Regulators" - depends on AB8500_CORE - help - This driver supports the regulators found on the ST-Ericsson mixed - signal AB8500 PMIC - -config REGULATOR_DBX500_PRCMU - bool +config REGULATOR_SKY81452 + tristate "Skyworks Solutions SKY81452 voltage regulator" + depends on MFD_SKY81452 + help + This driver supports Skyworks SKY81452 voltage output regulator + via I2C bus. SKY81452 has one voltage linear regulator can be + programmed from 4.5V to 20V. -config REGULATOR_DB8500_PRCMU - bool "ST-Ericsson DB8500 Voltage Domain Regulators" - depends on MFD_DB8500_PRCMU - select REGULATOR_DBX500_PRCMU - help - This driver supports the voltage domain regulators controlled by the - DB8500 PRCMU + This driver can also be built as a module. If so, the module + will be called sky81452-regulator. -config REGULATOR_PALMAS - tristate "TI Palmas PMIC Regulators" - depends on MFD_PALMAS +config REGULATOR_TI_ABB + tristate "TI Adaptive Body Bias on-chip LDO" + depends on ARCH_OMAP + help + Select this option to support Texas Instruments' on-chip Adaptive Body + Bias (ABB) LDO regulators. It is recommended that this option be + enabled on required TI SoC. Certain Operating Performance Points + on TI SoCs may be unstable without enabling this as it provides + device specific optimized bias to allow/optimize functionality. + +config REGULATOR_STW481X_VMMC + bool "ST Microelectronics STW481X VMMC regulator" + depends on MFD_STW481X || COMPILE_TEST + default y if MFD_STW481X help - If you wish to control the regulators on the Palmas series of - chips say Y here. This will enable support for all the software - controllable SMPS/LDO regulators. - - The regulators available on Palmas series chips vary depending - on the muxing. This is handled automatically in the driver by - reading the mux info from OTP. + This driver supports the internal VMMC regulator in the STw481x + PMIC chips. config REGULATOR_TPS51632 tristate "TI TPS51632 Power Regulator" @@ -428,6 +730,15 @@ voltage regulators. It supports software based voltage control for different voltage domains +config REGULATOR_TPS65218 + tristate "TI TPS65218 Power regulators" + depends on MFD_TPS65218 && OF + help + This driver supports TPS65218 voltage regulator chips. TPS65218 + provides six step-down converters and one general-purpose LDO + voltage regulators. It supports software based voltage control + for different voltage domains + config REGULATOR_TPS6524X tristate "TI TPS6524X Power regulators" depends on SPI @@ -466,7 +777,7 @@ output to control regulators. config REGULATOR_TWL4030 - bool "TI TWL4030/TWL5030/TWL6030/TPS659x0 PMIC" + tristate "TI TWL4030/TWL5030/TWL6030/TPS659x0 PMIC" depends on TWL4030_CORE help This driver supports the voltage regulators provided by @@ -507,12 +818,23 @@ This driver provides support for the voltage regulators on the WM8994 CODEC. -config REGULATOR_AS3711 - tristate "AS3711 PMIC" - depends on MFD_AS3711 +config REGULATOR_RPM_GLINK + bool "RPM GLINK regulator driver" + depends on OF + depends on MSM_RPM_GLINK + help + Compile in support for the RPM GLINK regulator driver which is used for + setting voltages and other parameters of the various power rails + supplied by some Qualcomm PMICs. The RPM GLINK regulator driver should + be used on systems which contain an RPM which communicates with the + application processor over GLINK. + +config REGULATOR_IPQ40XX + tristate "IPQ40xx regulator support" + depends on ARCH_QCOM help - This driver provides support for the voltage regulators on the - AS3711 PMIC + This driver provides support for the voltage regulators of the + IPQ40xx devices. endif