--- zzzz-none-000/linux-3.10.107/drivers/s390/scsi/zfcp_ccw.c	2017-06-27 09:49:32.000000000 +0000
+++ scorpion-7490-727/linux-3.10.107/drivers/s390/scsi/zfcp_ccw.c	2021-02-04 17:41:59.000000000 +0000
@@ -56,8 +56,22 @@
 	zfcp_erp_set_adapter_status(adapter, ZFCP_STATUS_COMMON_RUNNING);
 	zfcp_erp_adapter_reopen(adapter, ZFCP_STATUS_COMMON_ERP_FAILED,
 				tag);
+
+	/*
+	 * We want to scan ports here, with some random backoff and without
+	 * rate limit. Recovery has already scheduled a port scan for us,
+	 * but with both random delay and rate limit. Nevertheless we get
+	 * what we want here by flushing the scheduled work after sleeping
+	 * an equivalent random time.
+	 * Let the port scan random delay elapse first. If recovery finishes
+	 * up to that point in time, that would be perfect for both recovery
+	 * and port scan. If not, i.e. recovery takes ages, there was no
+	 * point in waiting a random delay on top of the time consumed by
+	 * recovery.
+	 */
+	msleep(zfcp_fc_port_scan_backoff());
 	zfcp_erp_wait(adapter);
-	flush_work(&adapter->scan_work); /* ok to call even if nothing queued */
+	flush_delayed_work(&adapter->scan_work);
 
 	zfcp_ccw_adapter_put(adapter);
 
@@ -72,15 +86,6 @@
 MODULE_DEVICE_TABLE(ccw, zfcp_ccw_device_id);
 
 /**
- * zfcp_ccw_priv_sch - check if subchannel is privileged
- * @adapter: Adapter/Subchannel to check
- */
-int zfcp_ccw_priv_sch(struct zfcp_adapter *adapter)
-{
-	return adapter->ccw_device->id.dev_model == ZFCP_MODEL_PRIV;
-}
-
-/**
  * zfcp_ccw_probe - probe function of zfcp driver
  * @cdev: pointer to belonging ccw device
  *
@@ -129,10 +134,10 @@
 	zfcp_ccw_adapter_put(adapter); /* put from zfcp_ccw_adapter_by_cdev */
 
 	list_for_each_entry_safe(unit, u, &unit_remove_lh, list)
-		zfcp_device_unregister(&unit->dev, &zfcp_sysfs_unit_attrs);
+		device_unregister(&unit->dev);
 
 	list_for_each_entry_safe(port, p, &port_remove_lh, list)
-		zfcp_device_unregister(&port->dev, &zfcp_sysfs_port_attrs);
+		device_unregister(&port->dev);
 
 	zfcp_adapter_unregister(adapter);
 }
@@ -171,11 +176,19 @@
 	adapter->req_no = 0;
 
 	zfcp_ccw_activate(cdev, 0, "ccsonl1");
-	/* scan for remote ports
-	   either at the end of any successful adapter recovery
-	   or only after the adapter recovery for setting a device online */
+
+	/*
+	 * We want to scan ports here, always, with some random delay and
+	 * without rate limit - basically what zfcp_ccw_activate() has
+	 * achieved for us. Not quite! That port scan depended on
+	 * !no_auto_port_rescan. So let's cover the no_auto_port_rescan
+	 * case here to make sure a port scan is done unconditionally.
+	 * Since zfcp_ccw_activate() has waited the desired random time,
+	 * we can immediately schedule and flush a port scan for the
+	 * remaining cases.
+	 */
 	zfcp_fc_inverse_conditional_port_scan(adapter);
-	flush_work(&adapter->scan_work); /* ok to call even if nothing queued */
+	flush_delayed_work(&adapter->scan_work);
 	zfcp_ccw_adapter_put(adapter);
 	return 0;
 }