--- zzzz-none-000/linux-3.10.107/drivers/scsi/hpsa_cmd.h 2017-06-27 09:49:32.000000000 +0000 +++ scorpion-7490-727/linux-3.10.107/drivers/scsi/hpsa_cmd.h 2021-02-04 17:41:59.000000000 +0000 @@ -1,6 +1,7 @@ /* * Disk Array driver for HP Smart Array SAS controllers - * Copyright 2000, 2009 Hewlett-Packard Development Company, L.P. + * Copyright 2014-2015 PMC-Sierra, Inc. + * Copyright 2000,2009-2015 Hewlett-Packard Development Company, L.P. * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -11,11 +12,7 @@ * MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, GOOD TITLE or * NON INFRINGEMENT. See the GNU General Public License for more details. * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. - * - * Questions/Comments/Bugfixes to iss_storagedev@hp.com + * Questions/Comments/Bugfixes to storagedev@pmcs.com * */ #ifndef HPSA_CMD_H @@ -25,6 +22,7 @@ #define SENSEINFOBYTES 32 /* may vary between hbas */ #define SG_ENTRIES_IN_CMD 32 /* Max SG entries excluding chain blocks */ #define HPSA_SG_CHAIN 0x80000000 +#define HPSA_SG_LAST 0x40000000 #define MAXREPLYQS 256 /* Command Status value */ @@ -41,6 +39,22 @@ #define CMD_UNSOLICITED_ABORT 0x000A #define CMD_TIMEOUT 0x000B #define CMD_UNABORTABLE 0x000C +#define CMD_TMF_STATUS 0x000D +#define CMD_IOACCEL_DISABLED 0x000E +#define CMD_CTLR_LOCKUP 0xffff +/* Note: CMD_CTLR_LOCKUP is not a value defined by the CISS spec + * it is a value defined by the driver that commands can be marked + * with when a controller lockup has been detected by the driver + */ + +/* TMF function status values */ +#define CISS_TMF_COMPLETE 0x00 +#define CISS_TMF_INVALID_FRAME 0x02 +#define CISS_TMF_NOT_SUPPORTED 0x04 +#define CISS_TMF_FAILED 0x05 +#define CISS_TMF_SUCCESS 0x08 +#define CISS_TMF_WRONG_LUN 0x09 +#define CISS_TMF_OVERLAPPED_TAG 0x0a /* Unit Attentions ASC's as defined for the MSA2012sa */ #define POWER_OR_RESET 0x29 @@ -79,8 +93,9 @@ #define ATTR_ACA 0x07 /* cdb type */ -#define TYPE_CMD 0x00 -#define TYPE_MSG 0x01 +#define TYPE_CMD 0x00 +#define TYPE_MSG 0x01 +#define TYPE_IOACCEL2_CMD 0x81 /* 0x81 is not used by hardware */ /* Message Types */ #define HPSA_TASK_MANAGEMENT 0x00 @@ -125,9 +140,12 @@ #define CFGTBL_AccCmds 0x00000001l #define DOORBELL_CTLR_RESET 0x00000004l #define DOORBELL_CTLR_RESET2 0x00000020l +#define DOORBELL_CLEAR_EVENTS 0x00000040l #define CFGTBL_Trans_Simple 0x00000002l #define CFGTBL_Trans_Performant 0x00000004l +#define CFGTBL_Trans_io_accel1 0x00000080l +#define CFGTBL_Trans_io_accel2 0x00000100l #define CFGTBL_Trans_use_short_tags 0x20000000l #define CFGTBL_Trans_enable_directed_msix (1 << 30) @@ -135,6 +153,29 @@ #define CFGTBL_BusType_Ultra3 0x00000002l #define CFGTBL_BusType_Fibre1G 0x00000100l #define CFGTBL_BusType_Fibre2G 0x00000200l + +/* VPD Inquiry types */ +#define HPSA_VPD_SUPPORTED_PAGES 0x00 +#define HPSA_VPD_LV_DEVICE_GEOMETRY 0xC1 +#define HPSA_VPD_LV_IOACCEL_STATUS 0xC2 +#define HPSA_VPD_LV_STATUS 0xC3 +#define HPSA_VPD_HEADER_SZ 4 + +/* Logical volume states */ +#define HPSA_VPD_LV_STATUS_UNSUPPORTED 0xff +#define HPSA_LV_OK 0x0 +#define HPSA_LV_NOT_AVAILABLE 0x0b +#define HPSA_LV_UNDERGOING_ERASE 0x0F +#define HPSA_LV_UNDERGOING_RPI 0x12 +#define HPSA_LV_PENDING_RPI 0x13 +#define HPSA_LV_ENCRYPTED_NO_KEY 0x14 +#define HPSA_LV_PLAINTEXT_IN_ENCRYPT_ONLY_CONTROLLER 0x15 +#define HPSA_LV_UNDERGOING_ENCRYPTION 0x16 +#define HPSA_LV_UNDERGOING_ENCRYPTION_REKEYING 0x17 +#define HPSA_LV_ENCRYPTED_IN_NON_ENCRYPTED_CONTROLLER 0x18 +#define HPSA_LV_PENDING_ENCRYPTION 0x19 +#define HPSA_LV_PENDING_ENCRYPTION_REKEYING 0x1A + struct vals32 { u32 lower; u32 upper; @@ -162,17 +203,73 @@ #define HPSA_REPORT_LOG 0xc2 /* Report Logical LUNs */ #define HPSA_REPORT_PHYS 0xc3 /* Report Physical LUNs */ +#define HPSA_REPORT_PHYS_EXTENDED 0x02 +#define HPSA_CISS_READ 0xc0 /* CISS Read */ +#define HPSA_GET_RAID_MAP 0xc8 /* CISS Get RAID Layout Map */ + +#define RAID_MAP_MAX_ENTRIES 256 + +struct raid_map_disk_data { + u32 ioaccel_handle; /**< Handle to access this disk via the + * I/O accelerator */ + u8 xor_mult[2]; /**< XOR multipliers for this position, + * valid for data disks only */ + u8 reserved[2]; +}; + +struct raid_map_data { + __le32 structure_size; /* Size of entire structure in bytes */ + __le32 volume_blk_size; /* bytes / block in the volume */ + __le64 volume_blk_cnt; /* logical blocks on the volume */ + u8 phys_blk_shift; /* Shift factor to convert between + * units of logical blocks and physical + * disk blocks */ + u8 parity_rotation_shift; /* Shift factor to convert between units + * of logical stripes and physical + * stripes */ + __le16 strip_size; /* blocks used on each disk / stripe */ + __le64 disk_starting_blk; /* First disk block used in volume */ + __le64 disk_blk_cnt; /* disk blocks used by volume / disk */ + __le16 data_disks_per_row; /* data disk entries / row in the map */ + __le16 metadata_disks_per_row;/* mirror/parity disk entries / row + * in the map */ + __le16 row_cnt; /* rows in each layout map */ + __le16 layout_map_count; /* layout maps (1 map per mirror/parity + * group) */ + __le16 flags; /* Bit 0 set if encryption enabled */ +#define RAID_MAP_FLAG_ENCRYPT_ON 0x01 + __le16 dekindex; /* Data encryption key index. */ + u8 reserved[16]; + struct raid_map_disk_data data[RAID_MAP_MAX_ENTRIES]; +}; + struct ReportLUNdata { u8 LUNListLength[4]; - u32 reserved; + u8 extended_response_flag; + u8 reserved[3]; u8 LUN[HPSA_MAX_LUN][8]; }; +struct ext_report_lun_entry { + u8 lunid[8]; +#define MASKED_DEVICE(x) ((x)[3] & 0xC0) +#define GET_BMIC_BUS(lunid) ((lunid)[7] & 0x3F) +#define GET_BMIC_LEVEL_TWO_TARGET(lunid) ((lunid)[6]) +#define GET_BMIC_DRIVE_NUMBER(lunid) (((GET_BMIC_BUS((lunid)) - 1) << 8) + \ + GET_BMIC_LEVEL_TWO_TARGET((lunid))) + u8 wwid[8]; + u8 device_type; + u8 device_flags; + u8 lun_count; /* multi-lun device, how many luns */ + u8 redundant_paths; + u32 ioaccel_handle; /* ioaccel1 only uses lower 16 bits */ +}; + struct ReportExtendedLUNdata { u8 LUNListLength[4]; u8 extended_response_flag; u8 reserved[3]; - u8 LUN[HPSA_MAX_LUN][24]; + struct ext_report_lun_entry LUN[HPSA_MAX_PHYS_LUN]; }; struct SenseSubsystem_info { @@ -187,6 +284,13 @@ #define BMIC_CACHE_FLUSH 0xc2 #define HPSA_CACHE_FLUSH 0x01 /* C2 was already being used by HPSA */ #define BMIC_FLASH_FIRMWARE 0xF7 +#define BMIC_SENSE_CONTROLLER_PARAMETERS 0x64 +#define BMIC_IDENTIFY_PHYSICAL_DEVICE 0x15 +#define BMIC_IDENTIFY_CONTROLLER 0x11 +#define BMIC_SET_DIAG_OPTIONS 0xF4 +#define BMIC_SENSE_DIAG_OPTIONS 0xF5 +#define HPSA_DIAG_OPTS_DISABLE_RLD_CACHING 0x40000000 +#define BMIC_SENSE_SUBSYSTEM_INFORMATION 0x66 /* Command List Structure */ union SCSI3Addr { @@ -232,31 +336,39 @@ struct CommandListHeader { u8 ReplyQueue; u8 SGList; - u16 SGTotal; - struct vals32 Tag; + __le16 SGTotal; + __le64 tag; union LUNAddr LUN; }; struct RequestBlock { u8 CDBLen; - struct { - u8 Type:3; - u8 Attribute:3; - u8 Direction:2; - } Type; + /* + * type_attr_dir: + * type: low 3 bits + * attr: middle 3 bits + * dir: high 2 bits + */ + u8 type_attr_dir; +#define TYPE_ATTR_DIR(t, a, d) ((((d) & 0x03) << 6) |\ + (((a) & 0x07) << 3) |\ + ((t) & 0x07)) +#define GET_TYPE(tad) ((tad) & 0x07) +#define GET_ATTR(tad) (((tad) >> 3) & 0x07) +#define GET_DIR(tad) (((tad) >> 6) & 0x03) u16 Timeout; u8 CDB[16]; }; struct ErrDescriptor { - struct vals32 Addr; - u32 Len; + __le64 Addr; + __le32 Len; }; struct SGDescriptor { - struct vals32 Addr; - u32 Len; - u32 Ext; + __le64 Addr; + __le32 Len; + __le32 Ext; }; union MoreErrInfo { @@ -283,25 +395,26 @@ /* Command types */ #define CMD_IOCTL_PEND 0x01 #define CMD_SCSI 0x03 +#define CMD_IOACCEL1 0x04 +#define CMD_IOACCEL2 0x05 +#define IOACCEL2_TMF 0x06 -#define DIRECT_LOOKUP_SHIFT 5 -#define DIRECT_LOOKUP_BIT 0x10 +#define DIRECT_LOOKUP_SHIFT 4 #define DIRECT_LOOKUP_MASK (~((1 << DIRECT_LOOKUP_SHIFT) - 1)) #define HPSA_ERROR_BIT 0x02 struct ctlr_info; /* defined in hpsa.h */ -/* The size of this structure needs to be divisible by 32 - * on all architectures because low 5 bits of the addresses +/* The size of this structure needs to be divisible by 128 + * on all architectures. The low 4 bits of the addresses * are used as follows: * * bit 0: to device, used to indicate "performant mode" command * from device, indidcates error status. * bit 1-3: to device, indicates block fetch table entry for * reducing DMA in fetching commands from host memory. - * bit 4: used to indicate whether tag is "direct lookup" (index), - * or a bus address. */ +#define COMMANDLIST_ALIGNMENT 128 struct CommandList { struct CommandListHeader Header; struct RequestBlock Request; @@ -313,76 +426,257 @@ struct ctlr_info *h; int cmd_type; long cmdindex; - struct list_head list; - struct request *rq; struct completion *waiting; - void *scsi_cmd; + struct scsi_cmnd *scsi_cmd; + struct work_struct work; -/* on 64 bit architectures, to get this to be 32-byte-aligned - * it so happens we need PAD_64 bytes of padding, on 32 bit systems, - * we need PAD_32 bytes of padding (see below). This does that. - * If it happens that 64 bit and 32 bit systems need different - * padding, PAD_32 and PAD_64 can be set independently, and. - * the code below will do the right thing. + /* + * For commands using either of the two "ioaccel" paths to + * bypass the RAID stack and go directly to the physical disk + * phys_disk is a pointer to the hpsa_scsi_dev_t to which the + * i/o is destined. We need to store that here because the command + * may potentially encounter TASK SET FULL and need to be resubmitted + * For "normal" i/o's not using the "ioaccel" paths, phys_disk is + * not used. + */ + struct hpsa_scsi_dev_t *phys_disk; + + int abort_pending; + struct hpsa_scsi_dev_t *reset_pending; + atomic_t refcount; /* Must be last to avoid memset in hpsa_cmd_init() */ +} __aligned(COMMANDLIST_ALIGNMENT); + +/* Max S/G elements in I/O accelerator command */ +#define IOACCEL1_MAXSGENTRIES 24 +#define IOACCEL2_MAXSGENTRIES 28 + +/* + * Structure for I/O accelerator (mode 1) commands. + * Note that this structure must be 128-byte aligned in size. */ -#define IS_32_BIT ((8 - sizeof(long))/4) -#define IS_64_BIT (!IS_32_BIT) -#define PAD_32 (4) -#define PAD_64 (4) -#define COMMANDLIST_PAD (IS_32_BIT * PAD_32 + IS_64_BIT * PAD_64) - u8 pad[COMMANDLIST_PAD]; +#define IOACCEL1_COMMANDLIST_ALIGNMENT 128 +struct io_accel1_cmd { + __le16 dev_handle; /* 0x00 - 0x01 */ + u8 reserved1; /* 0x02 */ + u8 function; /* 0x03 */ + u8 reserved2[8]; /* 0x04 - 0x0B */ + u32 err_info; /* 0x0C - 0x0F */ + u8 reserved3[2]; /* 0x10 - 0x11 */ + u8 err_info_len; /* 0x12 */ + u8 reserved4; /* 0x13 */ + u8 sgl_offset; /* 0x14 */ + u8 reserved5[7]; /* 0x15 - 0x1B */ + __le32 transfer_len; /* 0x1C - 0x1F */ + u8 reserved6[4]; /* 0x20 - 0x23 */ + __le16 io_flags; /* 0x24 - 0x25 */ + u8 reserved7[14]; /* 0x26 - 0x33 */ + u8 LUN[8]; /* 0x34 - 0x3B */ + __le32 control; /* 0x3C - 0x3F */ + u8 CDB[16]; /* 0x40 - 0x4F */ + u8 reserved8[16]; /* 0x50 - 0x5F */ + __le16 host_context_flags; /* 0x60 - 0x61 */ + __le16 timeout_sec; /* 0x62 - 0x63 */ + u8 ReplyQueue; /* 0x64 */ + u8 reserved9[3]; /* 0x65 - 0x67 */ + __le64 tag; /* 0x68 - 0x6F */ + __le64 host_addr; /* 0x70 - 0x77 */ + u8 CISS_LUN[8]; /* 0x78 - 0x7F */ + struct SGDescriptor SG[IOACCEL1_MAXSGENTRIES]; +} __aligned(IOACCEL1_COMMANDLIST_ALIGNMENT); + +#define IOACCEL1_FUNCTION_SCSIIO 0x00 +#define IOACCEL1_SGLOFFSET 32 + +#define IOACCEL1_IOFLAGS_IO_REQ 0x4000 +#define IOACCEL1_IOFLAGS_CDBLEN_MASK 0x001F +#define IOACCEL1_IOFLAGS_CDBLEN_MAX 16 + +#define IOACCEL1_CONTROL_NODATAXFER 0x00000000 +#define IOACCEL1_CONTROL_DATA_OUT 0x01000000 +#define IOACCEL1_CONTROL_DATA_IN 0x02000000 +#define IOACCEL1_CONTROL_TASKPRIO_MASK 0x00007800 +#define IOACCEL1_CONTROL_TASKPRIO_SHIFT 11 +#define IOACCEL1_CONTROL_SIMPLEQUEUE 0x00000000 +#define IOACCEL1_CONTROL_HEADOFQUEUE 0x00000100 +#define IOACCEL1_CONTROL_ORDEREDQUEUE 0x00000200 +#define IOACCEL1_CONTROL_ACA 0x00000400 + +#define IOACCEL1_HCFLAGS_CISS_FORMAT 0x0013 + +#define IOACCEL1_BUSADDR_CMDTYPE 0x00000060 + +struct ioaccel2_sg_element { + __le64 address; + __le32 length; + u8 reserved[3]; + u8 chain_indicator; +#define IOACCEL2_CHAIN 0x80 }; +/* + * SCSI Response Format structure for IO Accelerator Mode 2 + */ +struct io_accel2_scsi_response { + u8 IU_type; +#define IOACCEL2_IU_TYPE_SRF 0x60 + u8 reserved1[3]; + u8 req_id[4]; /* request identifier */ + u8 reserved2[4]; + u8 serv_response; /* service response */ +#define IOACCEL2_SERV_RESPONSE_COMPLETE 0x000 +#define IOACCEL2_SERV_RESPONSE_FAILURE 0x001 +#define IOACCEL2_SERV_RESPONSE_TMF_COMPLETE 0x002 +#define IOACCEL2_SERV_RESPONSE_TMF_SUCCESS 0x003 +#define IOACCEL2_SERV_RESPONSE_TMF_REJECTED 0x004 +#define IOACCEL2_SERV_RESPONSE_TMF_WRONG_LUN 0x005 + u8 status; /* status */ +#define IOACCEL2_STATUS_SR_TASK_COMP_GOOD 0x00 +#define IOACCEL2_STATUS_SR_TASK_COMP_CHK_COND 0x02 +#define IOACCEL2_STATUS_SR_TASK_COMP_BUSY 0x08 +#define IOACCEL2_STATUS_SR_TASK_COMP_RES_CON 0x18 +#define IOACCEL2_STATUS_SR_TASK_COMP_SET_FULL 0x28 +#define IOACCEL2_STATUS_SR_TASK_COMP_ABORTED 0x40 +#define IOACCEL2_STATUS_SR_IOACCEL_DISABLED 0x0E +#define IOACCEL2_STATUS_SR_IO_ERROR 0x01 +#define IOACCEL2_STATUS_SR_IO_ABORTED 0x02 +#define IOACCEL2_STATUS_SR_NO_PATH_TO_DEVICE 0x03 +#define IOACCEL2_STATUS_SR_INVALID_DEVICE 0x04 +#define IOACCEL2_STATUS_SR_UNDERRUN 0x51 +#define IOACCEL2_STATUS_SR_OVERRUN 0x75 + u8 data_present; /* low 2 bits */ +#define IOACCEL2_NO_DATAPRESENT 0x000 +#define IOACCEL2_RESPONSE_DATAPRESENT 0x001 +#define IOACCEL2_SENSE_DATA_PRESENT 0x002 +#define IOACCEL2_RESERVED 0x003 + u8 sense_data_len; /* sense/response data length */ + u8 resid_cnt[4]; /* residual count */ + u8 sense_data_buff[32]; /* sense/response data buffer */ +}; + +/* + * Structure for I/O accelerator (mode 2 or m2) commands. + * Note that this structure must be 128-byte aligned in size. + */ +#define IOACCEL2_COMMANDLIST_ALIGNMENT 128 +struct io_accel2_cmd { + u8 IU_type; /* IU Type */ + u8 direction; /* direction, memtype, and encryption */ +#define IOACCEL2_DIRECTION_MASK 0x03 /* bits 0,1: direction */ +#define IOACCEL2_DIRECTION_MEMTYPE_MASK 0x04 /* bit 2: memtype source/dest */ + /* 0b=PCIe, 1b=DDR */ +#define IOACCEL2_DIRECTION_ENCRYPT_MASK 0x08 /* bit 3: encryption flag */ + /* 0=off, 1=on */ + u8 reply_queue; /* Reply Queue ID */ + u8 reserved1; /* Reserved */ + __le32 scsi_nexus; /* Device Handle */ + __le32 Tag; /* cciss tag, lower 4 bytes only */ + __le32 tweak_lower; /* Encryption tweak, lower 4 bytes */ + u8 cdb[16]; /* SCSI Command Descriptor Block */ + u8 cciss_lun[8]; /* 8 byte SCSI address */ + __le32 data_len; /* Total bytes to transfer */ + u8 cmd_priority_task_attr; /* priority and task attrs */ +#define IOACCEL2_PRIORITY_MASK 0x78 +#define IOACCEL2_ATTR_MASK 0x07 + u8 sg_count; /* Number of sg elements */ + __le16 dekindex; /* Data encryption key index */ + __le64 err_ptr; /* Error Pointer */ + __le32 err_len; /* Error Length*/ + __le32 tweak_upper; /* Encryption tweak, upper 4 bytes */ + struct ioaccel2_sg_element sg[IOACCEL2_MAXSGENTRIES]; + struct io_accel2_scsi_response error_data; +} __aligned(IOACCEL2_COMMANDLIST_ALIGNMENT); + +/* + * defines for Mode 2 command struct + * FIXME: this can't be all I need mfm + */ +#define IOACCEL2_IU_TYPE 0x40 +#define IOACCEL2_IU_TMF_TYPE 0x41 +#define IOACCEL2_DIR_NO_DATA 0x00 +#define IOACCEL2_DIR_DATA_IN 0x01 +#define IOACCEL2_DIR_DATA_OUT 0x02 +#define IOACCEL2_TMF_ABORT 0x01 +/* + * SCSI Task Management Request format for Accelerator Mode 2 + */ +struct hpsa_tmf_struct { + u8 iu_type; /* Information Unit Type */ + u8 reply_queue; /* Reply Queue ID */ + u8 tmf; /* Task Management Function */ + u8 reserved1; /* byte 3 Reserved */ + __le32 it_nexus; /* SCSI I-T Nexus */ + u8 lun_id[8]; /* LUN ID for TMF request */ + __le64 tag; /* cciss tag associated w/ request */ + __le64 abort_tag; /* cciss tag of SCSI cmd or TMF to abort */ + __le64 error_ptr; /* Error Pointer */ + __le32 error_len; /* Error Length */ +} __aligned(IOACCEL2_COMMANDLIST_ALIGNMENT); + /* Configuration Table Structure */ struct HostWrite { - u32 TransportRequest; - u32 Reserved; - u32 CoalIntDelay; - u32 CoalIntCount; + __le32 TransportRequest; + __le32 command_pool_addr_hi; + __le32 CoalIntDelay; + __le32 CoalIntCount; }; #define SIMPLE_MODE 0x02 #define PERFORMANT_MODE 0x04 #define MEMQ_MODE 0x08 +#define IOACCEL_MODE_1 0x80 + +#define DRIVER_SUPPORT_UA_ENABLE 0x00000001 struct CfgTable { - u8 Signature[4]; - u32 SpecValence; - u32 TransportSupport; - u32 TransportActive; - struct HostWrite HostWrite; - u32 CmdsOutMax; - u32 BusTypes; - u32 TransMethodOffset; - u8 ServerName[16]; - u32 HeartBeat; - u32 SCSI_Prefetch; - u32 MaxScatterGatherElements; - u32 MaxLogicalUnits; - u32 MaxPhysicalDevices; - u32 MaxPhysicalDrivesPerLogicalUnit; - u32 MaxPerformantModeCommands; - u32 MaxBlockFetch; - u32 PowerConservationSupport; - u32 PowerConservationEnable; - u32 TMFSupportFlags; + u8 Signature[4]; + __le32 SpecValence; + __le32 TransportSupport; + __le32 TransportActive; + struct HostWrite HostWrite; + __le32 CmdsOutMax; + __le32 BusTypes; + __le32 TransMethodOffset; + u8 ServerName[16]; + __le32 HeartBeat; + __le32 driver_support; +#define ENABLE_SCSI_PREFETCH 0x100 +#define ENABLE_UNIT_ATTN 0x01 + __le32 MaxScatterGatherElements; + __le32 MaxLogicalUnits; + __le32 MaxPhysicalDevices; + __le32 MaxPhysicalDrivesPerLogicalUnit; + __le32 MaxPerformantModeCommands; + __le32 MaxBlockFetch; + __le32 PowerConservationSupport; + __le32 PowerConservationEnable; + __le32 TMFSupportFlags; u8 TMFTagMask[8]; u8 reserved[0x78 - 0x70]; - u32 misc_fw_support; /* offset 0x78 */ -#define MISC_FW_DOORBELL_RESET (0x02) -#define MISC_FW_DOORBELL_RESET2 (0x010) + __le32 misc_fw_support; /* offset 0x78 */ +#define MISC_FW_DOORBELL_RESET 0x02 +#define MISC_FW_DOORBELL_RESET2 0x010 +#define MISC_FW_RAID_OFFLOAD_BASIC 0x020 +#define MISC_FW_EVENT_NOTIFY 0x080 u8 driver_version[32]; - + __le32 max_cached_write_size; + u8 driver_scratchpad[16]; + __le32 max_error_info_length; + __le32 io_accel_max_embedded_sg_count; + __le32 io_accel_request_size_offset; + __le32 event_notify; +#define HPSA_EVENT_NOTIFY_ACCEL_IO_PATH_STATE_CHANGE (1 << 30) +#define HPSA_EVENT_NOTIFY_ACCEL_IO_PATH_CONFIG_CHANGE (1 << 31) + __le32 clear_event_notify; }; #define NUM_BLOCKFETCH_ENTRIES 8 struct TransTable_struct { - u32 BlockFetch[NUM_BLOCKFETCH_ENTRIES]; - u32 RepQSize; - u32 RepQCount; - u32 RepQCtrAddrLow32; - u32 RepQCtrAddrHigh32; -#define MAX_REPLY_QUEUES 8 + __le32 BlockFetch[NUM_BLOCKFETCH_ENTRIES]; + __le32 RepQSize; + __le32 RepQCount; + __le32 RepQCtrAddrLow32; + __le32 RepQCtrAddrHigh32; +#define MAX_REPLY_QUEUES 64 struct vals32 RepQAddr[MAX_REPLY_QUEUES]; }; @@ -393,5 +687,160 @@ u32 board_id; }; +struct bmic_identify_controller { + u8 configured_logical_drive_count; /* offset 0 */ + u8 pad1[153]; + __le16 extended_logical_unit_count; /* offset 154 */ + u8 pad2[136]; + u8 controller_mode; /* offset 292 */ + u8 pad3[32]; +}; + + +struct bmic_identify_physical_device { + u8 scsi_bus; /* SCSI Bus number on controller */ + u8 scsi_id; /* SCSI ID on this bus */ + __le16 block_size; /* sector size in bytes */ + __le32 total_blocks; /* number for sectors on drive */ + __le32 reserved_blocks; /* controller reserved (RIS) */ + u8 model[40]; /* Physical Drive Model */ + u8 serial_number[40]; /* Drive Serial Number */ + u8 firmware_revision[8]; /* drive firmware revision */ + u8 scsi_inquiry_bits; /* inquiry byte 7 bits */ + u8 compaq_drive_stamp; /* 0 means drive not stamped */ + u8 last_failure_reason; +#define BMIC_LAST_FAILURE_TOO_SMALL_IN_LOAD_CONFIG 0x01 +#define BMIC_LAST_FAILURE_ERROR_ERASING_RIS 0x02 +#define BMIC_LAST_FAILURE_ERROR_SAVING_RIS 0x03 +#define BMIC_LAST_FAILURE_FAIL_DRIVE_COMMAND 0x04 +#define BMIC_LAST_FAILURE_MARK_BAD_FAILED 0x05 +#define BMIC_LAST_FAILURE_MARK_BAD_FAILED_IN_FINISH_REMAP 0x06 +#define BMIC_LAST_FAILURE_TIMEOUT 0x07 +#define BMIC_LAST_FAILURE_AUTOSENSE_FAILED 0x08 +#define BMIC_LAST_FAILURE_MEDIUM_ERROR_1 0x09 +#define BMIC_LAST_FAILURE_MEDIUM_ERROR_2 0x0a +#define BMIC_LAST_FAILURE_NOT_READY_BAD_SENSE 0x0b +#define BMIC_LAST_FAILURE_NOT_READY 0x0c +#define BMIC_LAST_FAILURE_HARDWARE_ERROR 0x0d +#define BMIC_LAST_FAILURE_ABORTED_COMMAND 0x0e +#define BMIC_LAST_FAILURE_WRITE_PROTECTED 0x0f +#define BMIC_LAST_FAILURE_SPIN_UP_FAILURE_IN_RECOVER 0x10 +#define BMIC_LAST_FAILURE_REBUILD_WRITE_ERROR 0x11 +#define BMIC_LAST_FAILURE_TOO_SMALL_IN_HOT_PLUG 0x12 +#define BMIC_LAST_FAILURE_BUS_RESET_RECOVERY_ABORTED 0x13 +#define BMIC_LAST_FAILURE_REMOVED_IN_HOT_PLUG 0x14 +#define BMIC_LAST_FAILURE_INIT_REQUEST_SENSE_FAILED 0x15 +#define BMIC_LAST_FAILURE_INIT_START_UNIT_FAILED 0x16 +#define BMIC_LAST_FAILURE_INQUIRY_FAILED 0x17 +#define BMIC_LAST_FAILURE_NON_DISK_DEVICE 0x18 +#define BMIC_LAST_FAILURE_READ_CAPACITY_FAILED 0x19 +#define BMIC_LAST_FAILURE_INVALID_BLOCK_SIZE 0x1a +#define BMIC_LAST_FAILURE_HOT_PLUG_REQUEST_SENSE_FAILED 0x1b +#define BMIC_LAST_FAILURE_HOT_PLUG_START_UNIT_FAILED 0x1c +#define BMIC_LAST_FAILURE_WRITE_ERROR_AFTER_REMAP 0x1d +#define BMIC_LAST_FAILURE_INIT_RESET_RECOVERY_ABORTED 0x1e +#define BMIC_LAST_FAILURE_DEFERRED_WRITE_ERROR 0x1f +#define BMIC_LAST_FAILURE_MISSING_IN_SAVE_RIS 0x20 +#define BMIC_LAST_FAILURE_WRONG_REPLACE 0x21 +#define BMIC_LAST_FAILURE_GDP_VPD_INQUIRY_FAILED 0x22 +#define BMIC_LAST_FAILURE_GDP_MODE_SENSE_FAILED 0x23 +#define BMIC_LAST_FAILURE_DRIVE_NOT_IN_48BIT_MODE 0x24 +#define BMIC_LAST_FAILURE_DRIVE_TYPE_MIX_IN_HOT_PLUG 0x25 +#define BMIC_LAST_FAILURE_DRIVE_TYPE_MIX_IN_LOAD_CFG 0x26 +#define BMIC_LAST_FAILURE_PROTOCOL_ADAPTER_FAILED 0x27 +#define BMIC_LAST_FAILURE_FAULTY_ID_BAY_EMPTY 0x28 +#define BMIC_LAST_FAILURE_FAULTY_ID_BAY_OCCUPIED 0x29 +#define BMIC_LAST_FAILURE_FAULTY_ID_INVALID_BAY 0x2a +#define BMIC_LAST_FAILURE_WRITE_RETRIES_FAILED 0x2b + +#define BMIC_LAST_FAILURE_SMART_ERROR_REPORTED 0x37 +#define BMIC_LAST_FAILURE_PHY_RESET_FAILED 0x38 +#define BMIC_LAST_FAILURE_ONLY_ONE_CTLR_CAN_SEE_DRIVE 0x40 +#define BMIC_LAST_FAILURE_KC_VOLUME_FAILED 0x41 +#define BMIC_LAST_FAILURE_UNEXPECTED_REPLACEMENT 0x42 +#define BMIC_LAST_FAILURE_OFFLINE_ERASE 0x80 +#define BMIC_LAST_FAILURE_OFFLINE_TOO_SMALL 0x81 +#define BMIC_LAST_FAILURE_OFFLINE_DRIVE_TYPE_MIX 0x82 +#define BMIC_LAST_FAILURE_OFFLINE_ERASE_COMPLETE 0x83 + + u8 flags; + u8 more_flags; + u8 scsi_lun; /* SCSI LUN for phys drive */ + u8 yet_more_flags; + u8 even_more_flags; + __le32 spi_speed_rules;/* SPI Speed data:Ultra disable diagnose */ + u8 phys_connector[2]; /* connector number on controller */ + u8 phys_box_on_bus; /* phys enclosure this drive resides */ + u8 phys_bay_in_box; /* phys drv bay this drive resides */ + __le32 rpm; /* Drive rotational speed in rpm */ + u8 device_type; /* type of drive */ + u8 sata_version; /* only valid when drive_type is SATA */ + __le64 big_total_block_count; + __le64 ris_starting_lba; + __le32 ris_size; + u8 wwid[20]; + u8 controller_phy_map[32]; + __le16 phy_count; + u8 phy_connected_dev_type[256]; + u8 phy_to_drive_bay_num[256]; + __le16 phy_to_attached_dev_index[256]; + u8 box_index; + u8 reserved; + __le16 extra_physical_drive_flags; +#define BMIC_PHYS_DRIVE_SUPPORTS_GAS_GAUGE(idphydrv) \ + (idphydrv->extra_physical_drive_flags & (1 << 10)) + u8 negotiated_link_rate[256]; + u8 phy_to_phy_map[256]; + u8 redundant_path_present_map; + u8 redundant_path_failure_map; + u8 active_path_number; + __le16 alternate_paths_phys_connector[8]; + u8 alternate_paths_phys_box_on_port[8]; + u8 multi_lun_device_lun_count; + u8 minimum_good_fw_revision[8]; + u8 unique_inquiry_bytes[20]; + u8 current_temperature_degreesC; + u8 temperature_threshold_degreesC; + u8 max_temperature_degreesC; + u8 logical_blocks_per_phys_block_exp; /* phyblocksize = 512*2^exp */ + __le16 current_queue_depth_limit; + u8 switch_name[10]; + __le16 switch_port; + u8 alternate_paths_switch_name[40]; + u8 alternate_paths_switch_port[8]; + __le16 power_on_hours; /* valid only if gas gauge supported */ + __le16 percent_endurance_used; /* valid only if gas gauge supported. */ +#define BMIC_PHYS_DRIVE_SSD_WEAROUT(idphydrv) \ + ((idphydrv->percent_endurance_used & 0x80) || \ + (idphydrv->percent_endurance_used > 10000)) + u8 drive_authentication; +#define BMIC_PHYS_DRIVE_AUTHENTICATED(idphydrv) \ + (idphydrv->drive_authentication == 0x80) + u8 smart_carrier_authentication; +#define BMIC_SMART_CARRIER_AUTHENTICATION_SUPPORTED(idphydrv) \ + (idphydrv->smart_carrier_authentication != 0x0) +#define BMIC_SMART_CARRIER_AUTHENTICATED(idphydrv) \ + (idphydrv->smart_carrier_authentication == 0x01) + u8 smart_carrier_app_fw_version; + u8 smart_carrier_bootloader_fw_version; + u8 encryption_key_name[64]; + __le32 misc_drive_flags; + __le16 dek_index; + u8 padding[112]; +}; + +struct bmic_sense_subsystem_info { + u8 primary_slot_number; + u8 reserved[3]; + u8 chasis_serial_number[32]; + u8 primary_world_wide_id[8]; + u8 primary_array_serial_number[32]; /* NULL terminated */ + u8 primary_cache_serial_number[32]; /* NULL terminated */ + u8 reserved_2[8]; + u8 secondary_array_serial_number[32]; + u8 secondary_cache_serial_number[32]; + u8 pad[332]; +}; + #pragma pack() #endif /* HPSA_CMD_H */