--- zzzz-none-000/linux-3.10.107/drivers/scsi/qla4xxx/ql4_init.c	2017-06-27 09:49:32.000000000 +0000
+++ scorpion-7490-727/linux-3.10.107/drivers/scsi/qla4xxx/ql4_init.c	2021-02-04 17:41:59.000000000 +0000
@@ -1,6 +1,6 @@
 /*
  * QLogic iSCSI HBA Driver
- * Copyright (c)  2003-2012 QLogic Corporation
+ * Copyright (c)  2003-2013 QLogic Corporation
  *
  * See LICENSE.qla4xxx for copyright and licensing details.
  */
@@ -107,7 +107,7 @@
 		    (unsigned long  __iomem *)&ha->qla4_82xx_reg->rsp_q_in);
 		writel(0,
 		    (unsigned long  __iomem *)&ha->qla4_82xx_reg->rsp_q_out);
-	} else if (is_qla8032(ha)) {
+	} else if (is_qla8032(ha) || is_qla8042(ha)) {
 		writel(0,
 		       (unsigned long __iomem *)&ha->qla4_83xx_reg->req_q_in);
 		writel(0,
@@ -282,6 +282,25 @@
 	return ipv4_wait|ipv6_wait;
 }
 
+static int qla4_80xx_is_minidump_dma_capable(struct scsi_qla_host *ha,
+		struct qla4_8xxx_minidump_template_hdr *md_hdr)
+{
+	int offset = (is_qla8022(ha)) ? QLA8022_TEMPLATE_CAP_OFFSET :
+					QLA83XX_TEMPLATE_CAP_OFFSET;
+	int rval = 1;
+	uint32_t *cap_offset;
+
+	cap_offset = (uint32_t *)((char *)md_hdr + offset);
+
+	if (!(le32_to_cpu(*cap_offset) & BIT_0)) {
+		ql4_printk(KERN_INFO, ha, "PEX DMA Not supported %d\n",
+			   *cap_offset);
+		rval = 0;
+	}
+
+	return rval;
+}
+
 /**
  * qla4xxx_alloc_fw_dump - Allocate memory for minidump data.
  * @ha: pointer to host adapter structure.
@@ -294,6 +313,7 @@
 	void *md_tmp;
 	dma_addr_t md_tmp_dma;
 	struct qla4_8xxx_minidump_template_hdr *md_hdr;
+	int dma_capable;
 
 	if (ha->fw_dump) {
 		ql4_printk(KERN_WARNING, ha,
@@ -314,6 +334,12 @@
 	/* Allocate memory for saving the template */
 	md_tmp = dma_alloc_coherent(&ha->pdev->dev, ha->fw_dump_tmplt_size,
 				    &md_tmp_dma, GFP_KERNEL);
+	if (!md_tmp) {
+		ql4_printk(KERN_INFO, ha,
+			   "scsi%ld: Failed to allocate DMA memory\n",
+			   ha->host_no);
+		return;
+	}
 
 	/* Request template */
 	status =  qla4xxx_get_minidump_template(ha, md_tmp_dma);
@@ -326,13 +352,19 @@
 
 	md_hdr = (struct qla4_8xxx_minidump_template_hdr *)md_tmp;
 
+	dma_capable = qla4_80xx_is_minidump_dma_capable(ha, md_hdr);
+
 	capture_debug_level = md_hdr->capture_debug_level;
 
 	/* Get capture mask based on module loadtime setting. */
-	if (ql4xmdcapmask >= 0x3 && ql4xmdcapmask <= 0x7F)
+	if ((ql4xmdcapmask >= 0x3 && ql4xmdcapmask <= 0x7F) ||
+	    (ql4xmdcapmask == 0xFF && dma_capable))  {
 		ha->fw_dump_capture_mask = ql4xmdcapmask;
-	else
+	} else {
+		if (ql4xmdcapmask == 0xFF)
+			ql4_printk(KERN_INFO, ha, "Falling back to default capture mask, as PEX DMA is not supported\n");
 		ha->fw_dump_capture_mask = capture_debug_level;
+	}
 
 	md_hdr->driver_capture_mask = ha->fw_dump_capture_mask;
 
@@ -864,6 +896,8 @@
 	if (status == QLA_SUCCESS) {
 		if (test_and_clear_bit(AF_GET_CRASH_RECORD, &ha->flags))
 			qla4xxx_get_crash_record(ha);
+
+		qla4xxx_init_rings(ha);
 	} else {
 		DEBUG(printk("scsi%ld: %s: Firmware has NOT started\n",
 			     ha->host_no, __func__));
@@ -940,7 +974,7 @@
 	 * while switching from polling to interrupt mode. IOCB interrupts are
 	 * enabled via isp_ops->enable_intrs.
 	 */
-	if (is_qla8032(ha))
+	if (is_qla8032(ha) || is_qla8042(ha))
 		qla4_83xx_enable_mbox_intrs(ha);
 
 	if (qla4xxx_about_firmware(ha) == QLA_ERROR)
@@ -959,13 +993,8 @@
 		qla4xxx_build_ddb_list(ha, is_reset);
 
 	set_bit(AF_ONLINE, &ha->flags);
-exit_init_hba:
-	if (is_qla80XX(ha) && (status == QLA_ERROR)) {
-		/* Since interrupts are registered in start_firmware for
-		 * 80XX, release them here if initialize_adapter fails */
-		qla4xxx_free_irqs(ha);
-	}
 
+exit_init_hba:
 	DEBUG2(printk("scsi%ld: initialize adapter: %s\n", ha->host_no,
 	    status == QLA_ERROR ? "FAILED" : "SUCCEEDED"));
 	return status;