--- zzzz-none-000/linux-3.10.107/include/linux/mfd/88pm80x.h 2017-06-27 09:49:32.000000000 +0000 +++ scorpion-7490-727/linux-3.10.107/include/linux/mfd/88pm80x.h 2021-02-04 17:41:59.000000000 +0000 @@ -17,11 +17,11 @@ #include #include -#define PM80X_VERSION_MASK (0xFF) /* 80X chip ID mask */ enum { CHIP_INVALID = 0, CHIP_PM800, CHIP_PM805, + CHIP_PM860, CHIP_MAX, }; @@ -61,60 +61,60 @@ /* page 0 basic: slave adder 0x60 */ #define PM800_STATUS_1 (0x01) -#define PM800_ONKEY_STS1 (1 << 0) -#define PM800_EXTON_STS1 (1 << 1) -#define PM800_CHG_STS1 (1 << 2) -#define PM800_BAT_STS1 (1 << 3) -#define PM800_VBUS_STS1 (1 << 4) -#define PM800_LDO_PGOOD_STS1 (1 << 5) -#define PM800_BUCK_PGOOD_STS1 (1 << 6) +#define PM800_ONKEY_STS1 BIT(0) +#define PM800_EXTON_STS1 BIT(1) +#define PM800_CHG_STS1 BIT(2) +#define PM800_BAT_STS1 BIT(3) +#define PM800_VBUS_STS1 BIT(4) +#define PM800_LDO_PGOOD_STS1 BIT(5) +#define PM800_BUCK_PGOOD_STS1 BIT(6) #define PM800_STATUS_2 (0x02) -#define PM800_RTC_ALARM_STS2 (1 << 0) +#define PM800_RTC_ALARM_STS2 BIT(0) /* Wakeup Registers */ -#define PM800_WAKEUP1 (0x0D) +#define PM800_WAKEUP1 (0x0D) -#define PM800_WAKEUP2 (0x0E) -#define PM800_WAKEUP2_INV_INT (1 << 0) -#define PM800_WAKEUP2_INT_CLEAR (1 << 1) -#define PM800_WAKEUP2_INT_MASK (1 << 2) +#define PM800_WAKEUP2 (0x0E) +#define PM800_WAKEUP2_INV_INT BIT(0) +#define PM800_WAKEUP2_INT_CLEAR BIT(1) +#define PM800_WAKEUP2_INT_MASK BIT(2) -#define PM800_POWER_UP_LOG (0x10) +#define PM800_POWER_UP_LOG (0x10) /* Referance and low power registers */ #define PM800_LOW_POWER1 (0x20) #define PM800_LOW_POWER2 (0x21) -#define PM800_LOW_POWER_CONFIG3 (0x22) -#define PM800_LOW_POWER_CONFIG4 (0x23) +#define PM800_LOW_POWER_CONFIG3 (0x22) +#define PM800_LOW_POWER_CONFIG4 (0x23) /* GPIO register */ #define PM800_GPIO_0_1_CNTRL (0x30) -#define PM800_GPIO0_VAL (1 << 0) +#define PM800_GPIO0_VAL BIT(0) #define PM800_GPIO0_GPIO_MODE(x) (x << 1) -#define PM800_GPIO1_VAL (1 << 4) +#define PM800_GPIO1_VAL BIT(4) #define PM800_GPIO1_GPIO_MODE(x) (x << 5) #define PM800_GPIO_2_3_CNTRL (0x31) -#define PM800_GPIO2_VAL (1 << 0) +#define PM800_GPIO2_VAL BIT(0) #define PM800_GPIO2_GPIO_MODE(x) (x << 1) -#define PM800_GPIO3_VAL (1 << 4) +#define PM800_GPIO3_VAL BIT(4) #define PM800_GPIO3_GPIO_MODE(x) (x << 5) #define PM800_GPIO3_MODE_MASK 0x1F #define PM800_GPIO3_HEADSET_MODE PM800_GPIO3_GPIO_MODE(6) -#define PM800_GPIO_4_CNTRL (0x32) -#define PM800_GPIO4_VAL (1 << 0) +#define PM800_GPIO_4_CNTRL (0x32) +#define PM800_GPIO4_VAL BIT(0) #define PM800_GPIO4_GPIO_MODE(x) (x << 1) #define PM800_HEADSET_CNTRL (0x38) -#define PM800_HEADSET_DET_EN (1 << 7) -#define PM800_HSDET_SLP (1 << 1) +#define PM800_HEADSET_DET_EN BIT(7) +#define PM800_HSDET_SLP BIT(1) /* PWM register */ -#define PM800_PWM1 (0x40) -#define PM800_PWM2 (0x41) -#define PM800_PWM3 (0x42) -#define PM800_PWM4 (0x43) +#define PM800_PWM1 (0x40) +#define PM800_PWM2 (0x41) +#define PM800_PWM3 (0x42) +#define PM800_PWM4 (0x43) /* RTC Registers */ #define PM800_RTC_CONTROL (0xD0) @@ -124,55 +124,55 @@ #define PM800_RTC_MISC4 (0xE4) #define PM800_RTC_MISC5 (0xE7) /* bit definitions of RTC Register 1 (0xD0) */ -#define PM800_ALARM1_EN (1 << 0) -#define PM800_ALARM_WAKEUP (1 << 4) -#define PM800_ALARM (1 << 5) -#define PM800_RTC1_USE_XO (1 << 7) +#define PM800_ALARM1_EN BIT(0) +#define PM800_ALARM_WAKEUP BIT(4) +#define PM800_ALARM BIT(5) +#define PM800_RTC1_USE_XO BIT(7) /* Regulator Control Registers: BUCK1,BUCK5,LDO1 have DVC */ /* buck registers */ -#define PM800_SLEEP_BUCK1 (0x30) +#define PM800_SLEEP_BUCK1 (0x30) /* BUCK Sleep Mode Register 1: BUCK[1..4] */ -#define PM800_BUCK_SLP1 (0x5A) -#define PM800_BUCK1_SLP1_SHIFT 0 -#define PM800_BUCK1_SLP1_MASK (0x3 << PM800_BUCK1_SLP1_SHIFT) +#define PM800_BUCK_SLP1 (0x5A) +#define PM800_BUCK1_SLP1_SHIFT 0 +#define PM800_BUCK1_SLP1_MASK (0x3 << PM800_BUCK1_SLP1_SHIFT) /* page 2 GPADC: slave adder 0x02 */ #define PM800_GPADC_MEAS_EN1 (0x01) -#define PM800_MEAS_EN1_VBAT (1 << 2) +#define PM800_MEAS_EN1_VBAT BIT(2) #define PM800_GPADC_MEAS_EN2 (0x02) -#define PM800_MEAS_EN2_RFTMP (1 << 0) -#define PM800_MEAS_GP0_EN (1 << 2) -#define PM800_MEAS_GP1_EN (1 << 3) -#define PM800_MEAS_GP2_EN (1 << 4) -#define PM800_MEAS_GP3_EN (1 << 5) -#define PM800_MEAS_GP4_EN (1 << 6) +#define PM800_MEAS_EN2_RFTMP BIT(0) +#define PM800_MEAS_GP0_EN BIT(2) +#define PM800_MEAS_GP1_EN BIT(3) +#define PM800_MEAS_GP2_EN BIT(4) +#define PM800_MEAS_GP3_EN BIT(5) +#define PM800_MEAS_GP4_EN BIT(6) #define PM800_GPADC_MISC_CONFIG1 (0x05) #define PM800_GPADC_MISC_CONFIG2 (0x06) -#define PM800_GPADC_MISC_GPFSM_EN (1 << 0) +#define PM800_GPADC_MISC_GPFSM_EN BIT(0) #define PM800_GPADC_SLOW_MODE(x) (x << 3) -#define PM800_GPADC_MISC_CONFIG3 (0x09) -#define PM800_GPADC_MISC_CONFIG4 (0x0A) +#define PM800_GPADC_MISC_CONFIG3 (0x09) +#define PM800_GPADC_MISC_CONFIG4 (0x0A) -#define PM800_GPADC_PREBIAS1 (0x0F) +#define PM800_GPADC_PREBIAS1 (0x0F) #define PM800_GPADC0_GP_PREBIAS_TIME(x) (x << 0) -#define PM800_GPADC_PREBIAS2 (0x10) +#define PM800_GPADC_PREBIAS2 (0x10) -#define PM800_GP_BIAS_ENA1 (0x14) -#define PM800_GPADC_GP_BIAS_EN0 (1 << 0) -#define PM800_GPADC_GP_BIAS_EN1 (1 << 1) -#define PM800_GPADC_GP_BIAS_EN2 (1 << 2) -#define PM800_GPADC_GP_BIAS_EN3 (1 << 3) +#define PM800_GP_BIAS_ENA1 (0x14) +#define PM800_GPADC_GP_BIAS_EN0 BIT(0) +#define PM800_GPADC_GP_BIAS_EN1 BIT(1) +#define PM800_GPADC_GP_BIAS_EN2 BIT(2) +#define PM800_GPADC_GP_BIAS_EN3 BIT(3) #define PM800_GP_BIAS_OUT1 (0x15) -#define PM800_BIAS_OUT_GP0 (1 << 0) -#define PM800_BIAS_OUT_GP1 (1 << 1) -#define PM800_BIAS_OUT_GP2 (1 << 2) -#define PM800_BIAS_OUT_GP3 (1 << 3) +#define PM800_BIAS_OUT_GP0 BIT(0) +#define PM800_BIAS_OUT_GP1 BIT(1) +#define PM800_BIAS_OUT_GP2 BIT(2) +#define PM800_BIAS_OUT_GP3 BIT(3) #define PM800_GPADC0_LOW_TH 0x20 #define PM800_GPADC1_LOW_TH 0x21 @@ -223,37 +223,37 @@ #define PM805_INT_STATUS1 (0x03) -#define PM805_INT1_HP1_SHRT (1 << 0) -#define PM805_INT1_HP2_SHRT (1 << 1) -#define PM805_INT1_MIC_CONFLICT (1 << 2) -#define PM805_INT1_CLIP_FAULT (1 << 3) -#define PM805_INT1_LDO_OFF (1 << 4) -#define PM805_INT1_SRC_DPLL_LOCK (1 << 5) +#define PM805_INT1_HP1_SHRT BIT(0) +#define PM805_INT1_HP2_SHRT BIT(1) +#define PM805_INT1_MIC_CONFLICT BIT(2) +#define PM805_INT1_CLIP_FAULT BIT(3) +#define PM805_INT1_LDO_OFF BIT(4) +#define PM805_INT1_SRC_DPLL_LOCK BIT(5) #define PM805_INT_STATUS2 (0x04) -#define PM805_INT2_MIC_DET (1 << 0) -#define PM805_INT2_SHRT_BTN_DET (1 << 1) -#define PM805_INT2_VOLM_BTN_DET (1 << 2) -#define PM805_INT2_VOLP_BTN_DET (1 << 3) -#define PM805_INT2_RAW_PLL_FAULT (1 << 4) -#define PM805_INT2_FINE_PLL_FAULT (1 << 5) +#define PM805_INT2_MIC_DET BIT(0) +#define PM805_INT2_SHRT_BTN_DET BIT(1) +#define PM805_INT2_VOLM_BTN_DET BIT(2) +#define PM805_INT2_VOLP_BTN_DET BIT(3) +#define PM805_INT2_RAW_PLL_FAULT BIT(4) +#define PM805_INT2_FINE_PLL_FAULT BIT(5) #define PM805_INT_MASK1 (0x05) #define PM805_INT_MASK2 (0x06) -#define PM805_SHRT_BTN_DET (1 << 1) +#define PM805_SHRT_BTN_DET BIT(1) /* number of status and int reg in a row */ #define PM805_INT_REG_NUM (2) #define PM805_MIC_DET1 (0x07) -#define PM805_MIC_DET_EN_MIC_DET (1 << 0) +#define PM805_MIC_DET_EN_MIC_DET BIT(0) #define PM805_MIC_DET2 (0x08) -#define PM805_MIC_DET_STATUS1 (0x09) +#define PM805_MIC_DET_STATUS1 (0x09) -#define PM805_MIC_DET_STATUS3 (0x0A) -#define PM805_AUTO_SEQ_STATUS1 (0x0B) -#define PM805_AUTO_SEQ_STATUS2 (0x0C) +#define PM805_MIC_DET_STATUS3 (0x0A) +#define PM805_AUTO_SEQ_STATUS1 (0x0B) +#define PM805_AUTO_SEQ_STATUS2 (0x0C) #define PM805_ADC_SETTING1 (0x10) #define PM805_ADC_SETTING2 (0x11) @@ -262,7 +262,7 @@ #define PM805_ADC_GAIN2 (0x13) #define PM805_DMIC_SETTING (0x15) #define PM805_DWS_SETTING (0x16) -#define PM805_MIC_CONFLICT_STS (0x17) +#define PM805_MIC_CONFLICT_STS (0x17) #define PM805_PDM_SETTING1 (0x20) #define PM805_PDM_SETTING2 (0x21) @@ -271,11 +271,11 @@ #define PM805_PDM_CONTROL2 (0x24) #define PM805_PDM_CONTROL3 (0x25) -#define PM805_HEADPHONE_SETTING (0x26) -#define PM805_HEADPHONE_GAIN_A2A (0x27) -#define PM805_HEADPHONE_SHORT_STATE (0x28) -#define PM805_EARPHONE_SETTING (0x29) -#define PM805_AUTO_SEQ_SETTING (0x2A) +#define PM805_HEADPHONE_SETTING (0x26) +#define PM805_HEADPHONE_GAIN_A2A (0x27) +#define PM805_HEADPHONE_SHORT_STATE (0x28) +#define PM805_EARPHONE_SETTING (0x29) +#define PM805_AUTO_SEQ_SETTING (0x2A) struct pm80x_rtc_pdata { int vrtc; @@ -299,8 +299,7 @@ struct regmap *regmap; struct regmap_irq_chip *regmap_irq_chip; struct regmap_irq_chip_data *irq_data; - unsigned char version; - int id; + int type; int irq; int irq_mode; unsigned long wu_flag; @@ -309,8 +308,14 @@ struct pm80x_platform_data { struct pm80x_rtc_pdata *rtc; - unsigned short power_page_addr; /* power page I2C address */ - unsigned short gpadc_page_addr; /* gpadc page I2C address */ + /* + * For the regulator not defined, set regulators[not_defined] to be + * NULL. num_regulators are the number of regulators supposed to be + * initialized. If all regulators are not defined, set num_regulators + * to be 0. + */ + struct regulator_init_data *regulators[PM800_ID_RG_MAX]; + unsigned int num_regulators; int irq_mode; /* Clear interrupt by read/write(0/1) */ int batt_det; /* enable/disable */ int (*plat_config)(struct pm80x_chip *chip, @@ -363,7 +368,6 @@ } #endif -extern int pm80x_init(struct i2c_client *client, - const struct i2c_device_id *id); +extern int pm80x_init(struct i2c_client *client); extern int pm80x_deinit(void); #endif /* __LINUX_MFD_88PM80X_H */