--- zzzz-none-000/linux-3.10.107/include/linux/pinctrl/pinconf-generic.h 2017-06-27 09:49:32.000000000 +0000 +++ scorpion-7490-727/linux-3.10.107/include/linux/pinctrl/pinconf-generic.h 2021-02-04 17:41:59.000000000 +0000 @@ -20,6 +20,11 @@ /** * enum pin_config_param - possible pin configuration parameters + * @PIN_CONFIG_BIAS_BUS_HOLD: the pin will be set to weakly latch so that it + * weakly drives the last value on a tristate bus, also known as a "bus + * holder", "bus keeper" or "repeater". This allows another device on the + * bus to change the value by driving the bus high or low and switching to + * tristate. The argument is ignored. * @PIN_CONFIG_BIAS_DISABLE: disable any pin bias on the pin, a * transition from say pull-up to pull-down implies that you disable * pull-up in the process, this setting disables all biasing. @@ -29,71 +34,103 @@ * if for example some other pin is going to drive the signal connected * to it for a while. Pins used for input are usually always high * impedance. - * @PIN_CONFIG_BIAS_PULL_UP: the pin will be pulled up (usually with high - * impedance to VDD). If the argument is != 0 pull-up is enabled, - * if it is 0, pull-up is disabled. * @PIN_CONFIG_BIAS_PULL_DOWN: the pin will be pulled down (usually with high * impedance to GROUND). If the argument is != 0 pull-down is enabled, - * if it is 0, pull-down is disabled. - * @PIN_CONFIG_DRIVE_PUSH_PULL: the pin will be driven actively high and - * low, this is the most typical case and is typically achieved with two - * active transistors on the output. Setting this config will enable - * push-pull mode, the argument is ignored. + * if it is 0, pull-down is total, i.e. the pin is connected to GROUND. + * @PIN_CONFIG_BIAS_PULL_PIN_DEFAULT: the pin will be pulled up or down based + * on embedded knowledge of the controller hardware, like current mux + * function. The pull direction and possibly strength too will normally + * be decided completely inside the hardware block and not be readable + * from the kernel side. + * If the argument is != 0 pull up/down is enabled, if it is 0, the + * configuration is ignored. The proper way to disable it is to use + * @PIN_CONFIG_BIAS_DISABLE. + * @PIN_CONFIG_BIAS_PULL_UP: the pin will be pulled up (usually with high + * impedance to VDD). If the argument is != 0 pull-up is enabled, + * if it is 0, pull-up is total, i.e. the pin is connected to VDD. * @PIN_CONFIG_DRIVE_OPEN_DRAIN: the pin will be driven with open drain (open * collector) which means it is usually wired with other output ports * which are then pulled up with an external resistor. Setting this * config will enable open drain mode, the argument is ignored. * @PIN_CONFIG_DRIVE_OPEN_SOURCE: the pin will be driven with open source - * (open emitter). Setting this config will enable open drain mode, the + * (open emitter). Setting this config will enable open source mode, the * argument is ignored. + * @PIN_CONFIG_DRIVE_PUSH_PULL: the pin will be driven actively high and + * low, this is the most typical case and is typically achieved with two + * active transistors on the output. Setting this config will enable + * push-pull mode, the argument is ignored. * @PIN_CONFIG_DRIVE_STRENGTH: the pin will sink or source at most the current * passed as argument. The argument is in mA. - * @PIN_CONFIG_INPUT_SCHMITT_ENABLE: control schmitt-trigger mode on the pin. - * If the argument != 0, schmitt-trigger mode is enabled. If it's 0, - * schmitt-trigger mode is disabled. + * @PIN_CONFIG_INPUT_DEBOUNCE: this will configure the pin to debounce mode, + * which means it will wait for signals to settle when reading inputs. The + * argument gives the debounce time in usecs. Setting the + * argument to zero turns debouncing off. + * @PIN_CONFIG_INPUT_ENABLE: enable the pin's input. Note that this does not + * affect the pin's ability to drive output. 1 enables input, 0 disables + * input. * @PIN_CONFIG_INPUT_SCHMITT: this will configure an input pin to run in * schmitt-trigger mode. If the schmitt-trigger has adjustable hysteresis, * the threshold value is given on a custom format as argument when * setting pins to this mode. - * @PIN_CONFIG_INPUT_DEBOUNCE: this will configure the pin to debounce mode, - * which means it will wait for signals to settle when reading inputs. The - * argument gives the debounce time on a custom format. Setting the - * argument to zero turns debouncing off. - * @PIN_CONFIG_POWER_SOURCE: if the pin can select between different power - * supplies, the argument to this parameter (on a custom format) tells - * the driver which alternative power source to use. - * @PIN_CONFIG_SLEW_RATE: if the pin can select slew rate, the argument to - * this parameter (on a custom format) tells the driver which alternative - * slew rate to use. + * @PIN_CONFIG_INPUT_SCHMITT_ENABLE: control schmitt-trigger mode on the pin. + * If the argument != 0, schmitt-trigger mode is enabled. If it's 0, + * schmitt-trigger mode is disabled. * @PIN_CONFIG_LOW_POWER_MODE: this will configure the pin for low power * operation, if several modes of operation are supported these can be * passed in the argument on a custom form, else just use argument 1 * to indicate low power mode, argument 0 turns low power mode off. - * @PIN_CONFIG_OUTPUT: this will configure the pin in output, use argument - * 1 to indicate high level, argument 0 to indicate low level. + * @PIN_CONFIG_OUTPUT: this will configure the pin as an output. Use argument + * 1 to indicate high level, argument 0 to indicate low level. (Please + * see Documentation/pinctrl.txt, section "GPIO mode pitfalls" for a + * discussion around this parameter.) + * @PIN_CONFIG_POWER_SOURCE: if the pin can select between different power + * supplies, the argument to this parameter (on a custom format) tells + * the driver which alternative power source to use. + * @PIN_CONFIG_SLEW_RATE: if the pin can select slew rate, the argument to + * this parameter (on a custom format) tells the driver which alternative + * slew rate to use. * @PIN_CONFIG_END: this is the last enumerator for pin configurations, if * you need to pass in custom configurations to the pin controller, use * PIN_CONFIG_END+1 as the base offset. */ enum pin_config_param { + PIN_CONFIG_BIAS_BUS_HOLD, PIN_CONFIG_BIAS_DISABLE, PIN_CONFIG_BIAS_HIGH_IMPEDANCE, - PIN_CONFIG_BIAS_PULL_UP, PIN_CONFIG_BIAS_PULL_DOWN, - PIN_CONFIG_DRIVE_PUSH_PULL, + PIN_CONFIG_BIAS_PULL_PIN_DEFAULT, + PIN_CONFIG_BIAS_PULL_UP, PIN_CONFIG_DRIVE_OPEN_DRAIN, PIN_CONFIG_DRIVE_OPEN_SOURCE, + PIN_CONFIG_DRIVE_PUSH_PULL, PIN_CONFIG_DRIVE_STRENGTH, - PIN_CONFIG_INPUT_SCHMITT_ENABLE, - PIN_CONFIG_INPUT_SCHMITT, PIN_CONFIG_INPUT_DEBOUNCE, - PIN_CONFIG_POWER_SOURCE, - PIN_CONFIG_SLEW_RATE, + PIN_CONFIG_DRIVE_CAP, + PIN_CONFIG_DRIVE_TYPE, + PIN_CONFIG_PULL_RES, + PIN_CONFIG_VM, + PIN_CONFIG_INPUT_ENABLE, + PIN_CONFIG_INPUT_SCHMITT, + PIN_CONFIG_INPUT_SCHMITT_ENABLE, PIN_CONFIG_LOW_POWER_MODE, PIN_CONFIG_OUTPUT, + PIN_CONFIG_POWER_SOURCE, + PIN_CONFIG_SLEW_RATE, PIN_CONFIG_END = 0x7FFF, }; +#ifdef CONFIG_DEBUG_FS +#define PCONFDUMP(a, b, c, d) { .param = a, .display = b, .format = c, \ + .has_arg = d } + +struct pin_config_item { + const enum pin_config_param param; + const char * const display; + const char * const format; + bool has_arg; +}; +#endif /* CONFIG_DEBUG_FS */ + /* * Helpful configuration macro to be used in tables etc. */ @@ -122,6 +159,56 @@ return PIN_CONF_PACKED(param, argument); } +#ifdef CONFIG_OF + +#include +#include +struct pinctrl_dev; +struct pinctrl_map; + +struct pinconf_generic_params { + const char * const property; + enum pin_config_param param; + u32 default_value; +}; + +int pinconf_generic_dt_subnode_to_map(struct pinctrl_dev *pctldev, + struct device_node *np, struct pinctrl_map **map, + unsigned *reserved_maps, unsigned *num_maps, + enum pinctrl_map_type type); +int pinconf_generic_dt_node_to_map(struct pinctrl_dev *pctldev, + struct device_node *np_config, struct pinctrl_map **map, + unsigned *num_maps, enum pinctrl_map_type type); + +static inline int pinconf_generic_dt_node_to_map_group( + struct pinctrl_dev *pctldev, struct device_node *np_config, + struct pinctrl_map **map, unsigned *num_maps) +{ + return pinconf_generic_dt_node_to_map(pctldev, np_config, map, num_maps, + PIN_MAP_TYPE_CONFIGS_GROUP); +} + +static inline int pinconf_generic_dt_node_to_map_pin( + struct pinctrl_dev *pctldev, struct device_node *np_config, + struct pinctrl_map **map, unsigned *num_maps) +{ + return pinconf_generic_dt_node_to_map(pctldev, np_config, map, num_maps, + PIN_MAP_TYPE_CONFIGS_PIN); +} + +static inline int pinconf_generic_dt_node_to_map_all( + struct pinctrl_dev *pctldev, struct device_node *np_config, + struct pinctrl_map **map, unsigned *num_maps) +{ + /* + * passing the type as PIN_MAP_TYPE_INVALID causes the underlying parser + * to infer the map type from the DT properties used. + */ + return pinconf_generic_dt_node_to_map(pctldev, np_config, map, num_maps, + PIN_MAP_TYPE_INVALID); +} +#endif + #endif /* CONFIG_GENERIC_PINCONF */ #endif /* __LINUX_PINCTRL_PINCONF_GENERIC_H */