--- zzzz-none-000/linux-3.10.107/net/mac80211/Kconfig	2017-06-27 09:49:32.000000000 +0000
+++ scorpion-7490-727/linux-3.10.107/net/mac80211/Kconfig	2021-02-04 17:41:59.000000000 +0000
@@ -4,8 +4,9 @@
 	select CRYPTO
 	select CRYPTO_ARC4
 	select CRYPTO_AES
+	select CRYPTO_CCM
+	select CRYPTO_GCM
 	select CRC32
-	select AVERAGE
 	---help---
 	  This option enables the hardware independent IEEE 802.11
 	  networking stack.
@@ -18,14 +19,6 @@
 config MAC80211_HAS_RC
 	bool
 
-config MAC80211_RC_PID
-	bool "PID controller based rate control algorithm" if EXPERT
-	select MAC80211_HAS_RC
-	---help---
-	  This option enables a TX rate control algorithm for
-	  mac80211 that uses a PID controller to select the TX
-	  rate.
-
 config MAC80211_RC_MINSTREL
 	bool "Minstrel" if EXPERT
 	select MAC80211_HAS_RC
@@ -40,6 +33,13 @@
 	---help---
 	  This option enables the 'minstrel_ht' TX rate control algorithm
 
+config MAC80211_RC_MINSTREL_VHT
+	bool "Minstrel 802.11ac support" if EXPERT
+	depends on MAC80211_RC_MINSTREL_HT
+	default n
+	---help---
+	  This option enables VHT in the 'minstrel_ht' TX rate control algorithm
+
 choice
 	prompt "Default rate control algorithm"
 	depends on MAC80211_HAS_RC
@@ -50,14 +50,6 @@
 	  overridden through the ieee80211_default_rc_algo module
 	  parameter if different algorithms are available.
 
-config MAC80211_RC_DEFAULT_PID
-	bool "PID controller based rate control algorithm"
-	depends on MAC80211_RC_PID
-	---help---
-	  Select the PID controller based rate control as the
-	  default rate control algorithm. You should choose
-	  this unless you know what you are doing.
-
 config MAC80211_RC_DEFAULT_MINSTREL
 	bool "Minstrel"
 	depends on MAC80211_RC_MINSTREL
@@ -71,7 +63,6 @@
 	string
 	default "minstrel_ht" if MAC80211_RC_DEFAULT_MINSTREL && MAC80211_RC_MINSTREL_HT
 	default "minstrel" if MAC80211_RC_DEFAULT_MINSTREL
-	default "pid" if MAC80211_RC_DEFAULT_PID
 	default ""
 
 endif
@@ -185,6 +176,17 @@
 
 	  Do not select this option.
 
+config MAC80211_OCB_DEBUG
+	bool "Verbose OCB debugging"
+	depends on MAC80211_DEBUG_MENU
+	---help---
+	  Selecting this option causes mac80211 to print out
+	  very verbose OCB debugging messages. It should not
+	  be selected on production systems as those messages
+	  are remotely triggerable.
+
+	  Do not select this option.
+
 config MAC80211_IBSS_DEBUG
 	bool "Verbose IBSS debugging"
 	depends on MAC80211_DEBUG_MENU
@@ -258,6 +260,17 @@
 
 	  Do not select this option.
 
+config MAC80211_MESH_CSA_DEBUG
+	bool "Verbose mesh channel switch debugging"
+	depends on MAC80211_DEBUG_MENU
+	depends on MAC80211_MESH
+	---help---
+	  Selecting this option causes mac80211 to print out very verbose mesh
+	  channel switch debugging messages (when mac80211 is taking part in a
+	  mesh network).
+
+	  Do not select this option.
+
 config MAC80211_MESH_PS_DEBUG
 	bool "Verbose mesh powersave debugging"
 	depends on MAC80211_DEBUG_MENU
@@ -288,6 +301,20 @@
 	---help---
 	  Selecting this option causes mac80211 to keep additional
 	  and very verbose statistics about TX and RX handler use
-	  and show them in debugfs.
+	  as well as a few selected dot11 counters. These will be
+	  exposed in debugfs.
+
+	  Note that some of the counters are not concurrency safe
+	  and may thus not always be accurate.
 
 	  If unsure, say N.
+
+config MAC80211_STA_HASH_MAX_SIZE
+	int "Station hash table maximum size" if MAC80211_DEBUG_MENU
+	default 0
+	---help---
+	  Setting this option to a low value (e.g. 4) allows testing the
+	  hash table with collisions relatively deterministically (just
+	  connect more stations than the number selected here.)
+
+	  If unsure, leave the default of 0.