/* * Edgeport USB Serial Converter driver * * Copyright (C) 2000-2002 Inside Out Networks, All rights reserved. * Copyright (C) 2001-2002 Greg Kroah-Hartman * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation; either version 2 of the License, or * (at your option) any later version. * * Supports the following devices: * EP/1 EP/2 EP/4 EP/21 EP/22 EP/221 EP/42 EP/421 WATCHPORT * * For questions or problems with this driver, contact Inside Out * Networks technical support, or Peter Berger , * or Al Borchers . */ #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include "io_16654.h" #include "io_usbvend.h" #include "io_ti.h" #define DRIVER_AUTHOR "Greg Kroah-Hartman and David Iacovelli" #define DRIVER_DESC "Edgeport USB Serial Driver" #define EPROM_PAGE_SIZE 64 /* different hardware types */ #define HARDWARE_TYPE_930 0 #define HARDWARE_TYPE_TIUMP 1 /* IOCTL_PRIVATE_TI_GET_MODE Definitions */ #define TI_MODE_CONFIGURING 0 /* Device has not entered start device */ #define TI_MODE_BOOT 1 /* Staying in boot mode */ #define TI_MODE_DOWNLOAD 2 /* Made it to download mode */ #define TI_MODE_TRANSITIONING 3 /* * Currently in boot mode but * transitioning to download mode */ /* read urb state */ #define EDGE_READ_URB_RUNNING 0 #define EDGE_READ_URB_STOPPING 1 #define EDGE_READ_URB_STOPPED 2 #define EDGE_CLOSING_WAIT 4000 /* in .01 sec */ /* Product information read from the Edgeport */ struct product_info { int TiMode; /* Current TI Mode */ __u8 hardware_type; /* Type of hardware */ } __attribute__((packed)); /* * Edgeport firmware header * * "build_number" has been set to 0 in all three of the images I have * seen, and Digi Tech Support suggests that it is safe to ignore it. * * "length" is the number of bytes of actual data following the header. * * "checksum" is the low order byte resulting from adding the values of * all the data bytes. */ struct edgeport_fw_hdr { u8 major_version; u8 minor_version; __le16 build_number; __le16 length; u8 checksum; } __packed; struct edgeport_port { __u16 uart_base; __u16 dma_address; __u8 shadow_msr; __u8 shadow_mcr; __u8 shadow_lsr; __u8 lsr_mask; __u32 ump_read_timeout; /* * Number of milliseconds the UMP will * wait without data before completing * a read short */ int baud_rate; int close_pending; int lsr_event; struct edgeport_serial *edge_serial; struct usb_serial_port *port; __u8 bUartMode; /* Port type, 0: RS232, etc. */ spinlock_t ep_lock; int ep_read_urb_state; int ep_write_urb_in_use; }; struct edgeport_serial { struct product_info product_info; u8 TI_I2C_Type; /* Type of I2C in UMP */ u8 TiReadI2C; /* * Set to TRUE if we have read the * I2c in Boot Mode */ struct mutex es_lock; int num_ports_open; struct usb_serial *serial; struct delayed_work heartbeat_work; int fw_version; bool use_heartbeat; }; /* Devices that this driver supports */ static const struct usb_device_id edgeport_1port_id_table[] = { { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_1) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_TI3410_EDGEPORT_1) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_TI3410_EDGEPORT_1I) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_PROXIMITY) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_MOTION) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_MOISTURE) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_TEMPERATURE) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_HUMIDITY) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_POWER) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_LIGHT) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_RADIATION) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_DISTANCE) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_ACCELERATION) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_PROX_DIST) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_PLUS_PWR_HP4CD) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_PLUS_PWR_PCI) }, { } }; static const struct usb_device_id edgeport_2port_id_table[] = { { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_2) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_2C) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_2I) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_421) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_21) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_42) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_4) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_4I) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_22I) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_221C) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_22C) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_21C) }, /* The 4, 8 and 16 port devices show up as multiple 2 port devices */ { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_4S) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_8) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_8S) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_416) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_416B) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_E5805A) }, { } }; /* Devices that this driver supports */ static const struct usb_device_id id_table_combined[] = { { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_1) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_TI3410_EDGEPORT_1) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_TI3410_EDGEPORT_1I) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_PROXIMITY) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_MOTION) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_MOISTURE) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_TEMPERATURE) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_HUMIDITY) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_POWER) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_LIGHT) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_RADIATION) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_DISTANCE) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_ACCELERATION) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_PROX_DIST) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_PLUS_PWR_HP4CD) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_PLUS_PWR_PCI) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_2) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_2C) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_2I) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_421) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_21) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_42) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_4) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_4I) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_22I) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_221C) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_22C) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_21C) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_4S) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_8) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_8S) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_416) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_416B) }, { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_E5805A) }, { } }; MODULE_DEVICE_TABLE(usb, id_table_combined); static int closing_wait = EDGE_CLOSING_WAIT; static bool ignore_cpu_rev; static int default_uart_mode; /* RS232 */ static void edge_tty_recv(struct usb_serial_port *port, unsigned char *data, int length); static void stop_read(struct edgeport_port *edge_port); static int restart_read(struct edgeport_port *edge_port); static void edge_set_termios(struct tty_struct *tty, struct usb_serial_port *port, struct ktermios *old_termios); static void edge_send(struct usb_serial_port *port, struct tty_struct *tty); static int do_download_mode(struct edgeport_serial *serial, const struct firmware *fw); static int do_boot_mode(struct edgeport_serial *serial, const struct firmware *fw); /* sysfs attributes */ static int edge_create_sysfs_attrs(struct usb_serial_port *port); static int edge_remove_sysfs_attrs(struct usb_serial_port *port); /* * Some release of Edgeport firmware "down3.bin" after version 4.80 * introduced code to automatically disconnect idle devices on some * Edgeport models after periods of inactivity, typically ~60 seconds. * This occurs without regard to whether ports on the device are open * or not. Digi International Tech Support suggested: * * 1. Adding driver "heartbeat" code to reset the firmware timer by * requesting a descriptor record every 15 seconds, which should be * effective with newer firmware versions that require it, and benign * with older versions that do not. In practice 40 seconds seems often * enough. * 2. The heartbeat code is currently required only on Edgeport/416 models. */ #define FW_HEARTBEAT_VERSION_CUTOFF ((4 << 8) + 80) #define FW_HEARTBEAT_SECS 40 /* Timeouts in msecs: firmware downloads take longer */ #define TI_VSEND_TIMEOUT_DEFAULT 1000 #define TI_VSEND_TIMEOUT_FW_DOWNLOAD 10000 static int ti_vread_sync(struct usb_device *dev, __u8 request, __u16 value, __u16 index, u8 *data, int size) { int status; status = usb_control_msg(dev, usb_rcvctrlpipe(dev, 0), request, (USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_IN), value, index, data, size, 1000); if (status < 0) return status; if (status != size) { dev_dbg(&dev->dev, "%s - wanted to write %d, but only wrote %d\n", __func__, size, status); return -ECOMM; } return 0; } static int ti_vsend_sync(struct usb_device *dev, u8 request, u16 value, u16 index, u8 *data, int size, int timeout) { int status; status = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), request, (USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_OUT), value, index, data, size, timeout); if (status < 0) return status; if (status != size) { dev_dbg(&dev->dev, "%s - wanted to write %d, but only wrote %d\n", __func__, size, status); return -ECOMM; } return 0; } static int send_cmd(struct usb_device *dev, __u8 command, __u8 moduleid, __u16 value, u8 *data, int size) { return ti_vsend_sync(dev, command, value, moduleid, data, size, TI_VSEND_TIMEOUT_DEFAULT); } /* clear tx/rx buffers and fifo in TI UMP */ static int purge_port(struct usb_serial_port *port, __u16 mask) { int port_number = port->port_number; dev_dbg(&port->dev, "%s - port %d, mask %x\n", __func__, port_number, mask); return send_cmd(port->serial->dev, UMPC_PURGE_PORT, (__u8)(UMPM_UART1_PORT + port_number), mask, NULL, 0); } /** * read_download_mem - Read edgeport memory from TI chip * @dev: usb device pointer * @start_address: Device CPU address at which to read * @length: Length of above data * @address_type: Can read both XDATA and I2C * @buffer: pointer to input data buffer */ static int read_download_mem(struct usb_device *dev, int start_address, int length, __u8 address_type, __u8 *buffer) { int status = 0; __u8 read_length; u16 be_start_address; dev_dbg(&dev->dev, "%s - @ %x for %d\n", __func__, start_address, length); /* * Read in blocks of 64 bytes * (TI firmware can't handle more than 64 byte reads) */ while (length) { if (length > 64) read_length = 64; else read_length = (__u8)length; if (read_length > 1) { dev_dbg(&dev->dev, "%s - @ %x for %d\n", __func__, start_address, read_length); } /* * NOTE: Must use swab as wIndex is sent in little-endian * byte order regardless of host byte order. */ be_start_address = swab16((u16)start_address); status = ti_vread_sync(dev, UMPC_MEMORY_READ, (__u16)address_type, be_start_address, buffer, read_length); if (status) { dev_dbg(&dev->dev, "%s - ERROR %x\n", __func__, status); return status; } if (read_length > 1) usb_serial_debug_data(&dev->dev, __func__, read_length, buffer); /* Update pointers/length */ start_address += read_length; buffer += read_length; length -= read_length; } return status; } static int read_ram(struct usb_device *dev, int start_address, int length, __u8 *buffer) { return read_download_mem(dev, start_address, length, DTK_ADDR_SPACE_XDATA, buffer); } /* Read edgeport memory to a given block */ static int read_boot_mem(struct edgeport_serial *serial, int start_address, int length, __u8 *buffer) { int status = 0; int i; for (i = 0; i < length; i++) { status = ti_vread_sync(serial->serial->dev, UMPC_MEMORY_READ, serial->TI_I2C_Type, (__u16)(start_address+i), &buffer[i], 0x01); if (status) { dev_dbg(&serial->serial->dev->dev, "%s - ERROR %x\n", __func__, status); return status; } } dev_dbg(&serial->serial->dev->dev, "%s - start_address = %x, length = %d\n", __func__, start_address, length); usb_serial_debug_data(&serial->serial->dev->dev, __func__, length, buffer); serial->TiReadI2C = 1; return status; } /* Write given block to TI EPROM memory */ static int write_boot_mem(struct edgeport_serial *serial, int start_address, int length, __u8 *buffer) { int status = 0; int i; u8 *temp; /* Must do a read before write */ if (!serial->TiReadI2C) { temp = kmalloc(1, GFP_KERNEL); if (!temp) return -ENOMEM; status = read_boot_mem(serial, 0, 1, temp); kfree(temp); if (status) return status; } for (i = 0; i < length; ++i) { status = ti_vsend_sync(serial->serial->dev, UMPC_MEMORY_WRITE, buffer[i], (u16)(i + start_address), NULL, 0, TI_VSEND_TIMEOUT_DEFAULT); if (status) return status; } dev_dbg(&serial->serial->dev->dev, "%s - start_sddr = %x, length = %d\n", __func__, start_address, length); usb_serial_debug_data(&serial->serial->dev->dev, __func__, length, buffer); return status; } /* Write edgeport I2C memory to TI chip */ static int write_i2c_mem(struct edgeport_serial *serial, int start_address, int length, __u8 address_type, __u8 *buffer) { struct device *dev = &serial->serial->dev->dev; int status = 0; int write_length; u16 be_start_address; /* We can only send a maximum of 1 aligned byte page at a time */ /* calculate the number of bytes left in the first page */ write_length = EPROM_PAGE_SIZE - (start_address & (EPROM_PAGE_SIZE - 1)); if (write_length > length) write_length = length; dev_dbg(dev, "%s - BytesInFirstPage Addr = %x, length = %d\n", __func__, start_address, write_length); usb_serial_debug_data(dev, __func__, write_length, buffer); /* * Write first page. * * NOTE: Must use swab as wIndex is sent in little-endian byte order * regardless of host byte order. */ be_start_address = swab16((u16)start_address); status = ti_vsend_sync(serial->serial->dev, UMPC_MEMORY_WRITE, (u16)address_type, be_start_address, buffer, write_length, TI_VSEND_TIMEOUT_DEFAULT); if (status) { dev_dbg(dev, "%s - ERROR %d\n", __func__, status); return status; } length -= write_length; start_address += write_length; buffer += write_length; /* * We should be aligned now -- can write max page size bytes at a * time. */ while (length) { if (length > EPROM_PAGE_SIZE) write_length = EPROM_PAGE_SIZE; else write_length = length; dev_dbg(dev, "%s - Page Write Addr = %x, length = %d\n", __func__, start_address, write_length); usb_serial_debug_data(dev, __func__, write_length, buffer); /* * Write next page. * * NOTE: Must use swab as wIndex is sent in little-endian byte * order regardless of host byte order. */ be_start_address = swab16((u16)start_address); status = ti_vsend_sync(serial->serial->dev, UMPC_MEMORY_WRITE, (u16)address_type, be_start_address, buffer, write_length, TI_VSEND_TIMEOUT_DEFAULT); if (status) { dev_err(dev, "%s - ERROR %d\n", __func__, status); return status; } length -= write_length; start_address += write_length; buffer += write_length; } return status; } /* * Examine the UMP DMA registers and LSR * * Check the MSBit of the X and Y DMA byte count registers. * A zero in this bit indicates that the TX DMA buffers are empty * then check the TX Empty bit in the UART. */ static int tx_active(struct edgeport_port *port) { int status; struct out_endpoint_desc_block *oedb; __u8 *lsr; int bytes_left = 0; oedb = kmalloc(sizeof(*oedb), GFP_KERNEL); if (!oedb) return -ENOMEM; /* * Sigh, that's right, just one byte, as not all platforms can * do DMA from stack */ lsr = kmalloc(1, GFP_KERNEL); if (!lsr) { kfree(oedb); return -ENOMEM; } /* Read the DMA Count Registers */ status = read_ram(port->port->serial->dev, port->dma_address, sizeof(*oedb), (void *)oedb); if (status) goto exit_is_tx_active; dev_dbg(&port->port->dev, "%s - XByteCount 0x%X\n", __func__, oedb->XByteCount); /* and the LSR */ status = read_ram(port->port->serial->dev, port->uart_base + UMPMEM_OFFS_UART_LSR, 1, lsr); if (status) goto exit_is_tx_active; dev_dbg(&port->port->dev, "%s - LSR = 0x%X\n", __func__, *lsr); /* If either buffer has data or we are transmitting then return TRUE */ if ((oedb->XByteCount & 0x80) != 0) bytes_left += 64; if ((*lsr & UMP_UART_LSR_TX_MASK) == 0) bytes_left += 1; /* We return Not Active if we get any kind of error */ exit_is_tx_active: dev_dbg(&port->port->dev, "%s - return %d\n", __func__, bytes_left); kfree(lsr); kfree(oedb); return bytes_left; } static int choose_config(struct usb_device *dev) { /* * There may be multiple configurations on this device, in which case * we would need to read and parse all of them to find out which one * we want. However, we just support one config at this point, * configuration # 1, which is Config Descriptor 0. */ dev_dbg(&dev->dev, "%s - Number of Interfaces = %d\n", __func__, dev->config->desc.bNumInterfaces); dev_dbg(&dev->dev, "%s - MAX Power = %d\n", __func__, dev->config->desc.bMaxPower * 2); if (dev->config->desc.bNumInterfaces != 1) { dev_err(&dev->dev, "%s - bNumInterfaces is not 1, ERROR!\n", __func__); return -ENODEV; } return 0; } static int read_rom(struct edgeport_serial *serial, int start_address, int length, __u8 *buffer) { int status; if (serial->product_info.TiMode == TI_MODE_DOWNLOAD) { status = read_download_mem(serial->serial->dev, start_address, length, serial->TI_I2C_Type, buffer); } else { status = read_boot_mem(serial, start_address, length, buffer); } return status; } static int write_rom(struct edgeport_serial *serial, int start_address, int length, __u8 *buffer) { if (serial->product_info.TiMode == TI_MODE_BOOT) return write_boot_mem(serial, start_address, length, buffer); if (serial->product_info.TiMode == TI_MODE_DOWNLOAD) return write_i2c_mem(serial, start_address, length, serial->TI_I2C_Type, buffer); return -EINVAL; } /* Read a descriptor header from I2C based on type */ static int get_descriptor_addr(struct edgeport_serial *serial, int desc_type, struct ti_i2c_desc *rom_desc) { int start_address; int status; /* Search for requested descriptor in I2C */ start_address = 2; do { status = read_rom(serial, start_address, sizeof(struct ti_i2c_desc), (__u8 *)rom_desc); if (status) return 0; if (rom_desc->Type == desc_type) return start_address; start_address = start_address + sizeof(struct ti_i2c_desc) + le16_to_cpu(rom_desc->Size); } while ((start_address < TI_MAX_I2C_SIZE) && rom_desc->Type); return 0; } /* Validate descriptor checksum */ static int valid_csum(struct ti_i2c_desc *rom_desc, __u8 *buffer) { __u16 i; __u8 cs = 0; for (i = 0; i < le16_to_cpu(rom_desc->Size); i++) cs = (__u8)(cs + buffer[i]); if (cs != rom_desc->CheckSum) { pr_debug("%s - Mismatch %x - %x", __func__, rom_desc->CheckSum, cs); return -EINVAL; } return 0; } /* Make sure that the I2C image is good */ static int check_i2c_image(struct edgeport_serial *serial) { struct device *dev = &serial->serial->dev->dev; int status = 0; struct ti_i2c_desc *rom_desc; int start_address = 2; __u8 *buffer; __u16 ttype; rom_desc = kmalloc(sizeof(*rom_desc), GFP_KERNEL); if (!rom_desc) return -ENOMEM; buffer = kmalloc(TI_MAX_I2C_SIZE, GFP_KERNEL); if (!buffer) { kfree(rom_desc); return -ENOMEM; } /* Read the first byte (Signature0) must be 0x52 or 0x10 */ status = read_rom(serial, 0, 1, buffer); if (status) goto out; if (*buffer != UMP5152 && *buffer != UMP3410) { dev_err(dev, "%s - invalid buffer signature\n", __func__); status = -ENODEV; goto out; } do { /* Validate the I2C */ status = read_rom(serial, start_address, sizeof(struct ti_i2c_desc), (__u8 *)rom_desc); if (status) break; if ((start_address + sizeof(struct ti_i2c_desc) + le16_to_cpu(rom_desc->Size)) > TI_MAX_I2C_SIZE) { status = -ENODEV; dev_dbg(dev, "%s - structure too big, erroring out.\n", __func__); break; } dev_dbg(dev, "%s Type = 0x%x\n", __func__, rom_desc->Type); /* Skip type 2 record */ ttype = rom_desc->Type & 0x0f; if (ttype != I2C_DESC_TYPE_FIRMWARE_BASIC && ttype != I2C_DESC_TYPE_FIRMWARE_AUTO) { /* Read the descriptor data */ status = read_rom(serial, start_address + sizeof(struct ti_i2c_desc), le16_to_cpu(rom_desc->Size), buffer); if (status) break; status = valid_csum(rom_desc, buffer); if (status) break; } start_address = start_address + sizeof(struct ti_i2c_desc) + le16_to_cpu(rom_desc->Size); } while ((rom_desc->Type != I2C_DESC_TYPE_ION) && (start_address < TI_MAX_I2C_SIZE)); if ((rom_desc->Type != I2C_DESC_TYPE_ION) || (start_address > TI_MAX_I2C_SIZE)) status = -ENODEV; out: kfree(buffer); kfree(rom_desc); return status; } static int get_manuf_info(struct edgeport_serial *serial, __u8 *buffer) { int status; int start_address; struct ti_i2c_desc *rom_desc; struct edge_ti_manuf_descriptor *desc; struct device *dev = &serial->serial->dev->dev; rom_desc = kmalloc(sizeof(*rom_desc), GFP_KERNEL); if (!rom_desc) return -ENOMEM; start_address = get_descriptor_addr(serial, I2C_DESC_TYPE_ION, rom_desc); if (!start_address) { dev_dbg(dev, "%s - Edge Descriptor not found in I2C\n", __func__); status = -ENODEV; goto exit; } /* Read the descriptor data */ status = read_rom(serial, start_address+sizeof(struct ti_i2c_desc), le16_to_cpu(rom_desc->Size), buffer); if (status) goto exit; status = valid_csum(rom_desc, buffer); desc = (struct edge_ti_manuf_descriptor *)buffer; dev_dbg(dev, "%s - IonConfig 0x%x\n", __func__, desc->IonConfig); dev_dbg(dev, "%s - Version %d\n", __func__, desc->Version); dev_dbg(dev, "%s - Cpu/Board 0x%x\n", __func__, desc->CpuRev_BoardRev); dev_dbg(dev, "%s - NumPorts %d\n", __func__, desc->NumPorts); dev_dbg(dev, "%s - NumVirtualPorts %d\n", __func__, desc->NumVirtualPorts); dev_dbg(dev, "%s - TotalPorts %d\n", __func__, desc->TotalPorts); exit: kfree(rom_desc); return status; } /* Build firmware header used for firmware update */ static int build_i2c_fw_hdr(u8 *header, const struct firmware *fw) { __u8 *buffer; int buffer_size; int i; __u8 cs = 0; struct ti_i2c_desc *i2c_header; struct ti_i2c_image_header *img_header; struct ti_i2c_firmware_rec *firmware_rec; struct edgeport_fw_hdr *fw_hdr = (struct edgeport_fw_hdr *)fw->data; /* * In order to update the I2C firmware we must change the type 2 record * to type 0xF2. This will force the UMP to come up in Boot Mode. * Then while in boot mode, the driver will download the latest * firmware (padded to 15.5k) into the UMP ram. And finally when the * device comes back up in download mode the driver will cause the new * firmware to be copied from the UMP Ram to I2C and the firmware will * update the record type from 0xf2 to 0x02. */ /* * Allocate a 15.5k buffer + 2 bytes for version number (Firmware * Record) */ buffer_size = (((1024 * 16) - 512 ) + sizeof(struct ti_i2c_firmware_rec)); buffer = kmalloc(buffer_size, GFP_KERNEL); if (!buffer) return -ENOMEM; /* Set entire image of 0xffs */ memset(buffer, 0xff, buffer_size); /* Copy version number into firmware record */ firmware_rec = (struct ti_i2c_firmware_rec *)buffer; firmware_rec->Ver_Major = fw_hdr->major_version; firmware_rec->Ver_Minor = fw_hdr->minor_version; /* Pointer to fw_down memory image */ img_header = (struct ti_i2c_image_header *)&fw->data[4]; memcpy(buffer + sizeof(struct ti_i2c_firmware_rec), &fw->data[4 + sizeof(struct ti_i2c_image_header)], le16_to_cpu(img_header->Length)); for (i=0; i < buffer_size; i++) { cs = (__u8)(cs + buffer[i]); } kfree(buffer); /* Build new header */ i2c_header = (struct ti_i2c_desc *)header; firmware_rec = (struct ti_i2c_firmware_rec*)i2c_header->Data; i2c_header->Type = I2C_DESC_TYPE_FIRMWARE_BLANK; i2c_header->Size = cpu_to_le16(buffer_size); i2c_header->CheckSum = cs; firmware_rec->Ver_Major = fw_hdr->major_version; firmware_rec->Ver_Minor = fw_hdr->minor_version; return 0; } /* Try to figure out what type of I2c we have */ static int i2c_type_bootmode(struct edgeport_serial *serial) { struct device *dev = &serial->serial->dev->dev; int status; u8 *data; data = kmalloc(1, GFP_KERNEL); if (!data) return -ENOMEM; /* Try to read type 2 */ status = ti_vread_sync(serial->serial->dev, UMPC_MEMORY_READ, DTK_ADDR_SPACE_I2C_TYPE_II, 0, data, 0x01); if (status) dev_dbg(dev, "%s - read 2 status error = %d\n", __func__, status); else dev_dbg(dev, "%s - read 2 data = 0x%x\n", __func__, *data); if ((!status) && (*data == UMP5152 || *data == UMP3410)) { dev_dbg(dev, "%s - ROM_TYPE_II\n", __func__); serial->TI_I2C_Type = DTK_ADDR_SPACE_I2C_TYPE_II; goto out; } /* Try to read type 3 */ status = ti_vread_sync(serial->serial->dev, UMPC_MEMORY_READ, DTK_ADDR_SPACE_I2C_TYPE_III, 0, data, 0x01); if (status) dev_dbg(dev, "%s - read 3 status error = %d\n", __func__, status); else dev_dbg(dev, "%s - read 2 data = 0x%x\n", __func__, *data); if ((!status) && (*data == UMP5152 || *data == UMP3410)) { dev_dbg(dev, "%s - ROM_TYPE_III\n", __func__); serial->TI_I2C_Type = DTK_ADDR_SPACE_I2C_TYPE_III; goto out; } dev_dbg(dev, "%s - Unknown\n", __func__); serial->TI_I2C_Type = DTK_ADDR_SPACE_I2C_TYPE_II; status = -ENODEV; out: kfree(data); return status; } static int bulk_xfer(struct usb_serial *serial, void *buffer, int length, int *num_sent) { int status; status = usb_bulk_msg(serial->dev, usb_sndbulkpipe(serial->dev, serial->port[0]->bulk_out_endpointAddress), buffer, length, num_sent, 1000); return status; } /* Download given firmware image to the device (IN BOOT MODE) */ static int download_code(struct edgeport_serial *serial, __u8 *image, int image_length) { int status = 0; int pos; int transfer; int done; /* Transfer firmware image */ for (pos = 0; pos < image_length; ) { /* Read the next buffer from file */ transfer = image_length - pos; if (transfer > EDGE_FW_BULK_MAX_PACKET_SIZE) transfer = EDGE_FW_BULK_MAX_PACKET_SIZE; /* Transfer data */ status = bulk_xfer(serial->serial, &image[pos], transfer, &done); if (status) break; /* Advance buffer pointer */ pos += done; } return status; } /* FIXME!!! */ static int config_boot_dev(struct usb_device *dev) { return 0; } static int ti_cpu_rev(struct edge_ti_manuf_descriptor *desc) { return TI_GET_CPU_REVISION(desc->CpuRev_BoardRev); } static int check_fw_sanity(struct edgeport_serial *serial, const struct firmware *fw) { u16 length_total; u8 checksum = 0; int pos; struct device *dev = &serial->serial->interface->dev; struct edgeport_fw_hdr *fw_hdr = (struct edgeport_fw_hdr *)fw->data; if (fw->size < sizeof(struct edgeport_fw_hdr)) { dev_err(dev, "incomplete fw header\n"); return -EINVAL; } length_total = le16_to_cpu(fw_hdr->length) + sizeof(struct edgeport_fw_hdr); if (fw->size != length_total) { dev_err(dev, "bad fw size (expected: %u, got: %zu)\n", length_total, fw->size); return -EINVAL; } for (pos = sizeof(struct edgeport_fw_hdr); pos < fw->size; ++pos) checksum += fw->data[pos]; if (checksum != fw_hdr->checksum) { dev_err(dev, "bad fw checksum (expected: 0x%x, got: 0x%x)\n", fw_hdr->checksum, checksum); return -EINVAL; } return 0; } /* * DownloadTIFirmware - Download run-time operating firmware to the TI5052 * * This routine downloads the main operating code into the TI5052, using the * boot code already burned into E2PROM or ROM. */ static int download_fw(struct edgeport_serial *serial) { struct device *dev = &serial->serial->interface->dev; int status = 0; struct usb_interface_descriptor *interface; const struct firmware *fw; const char *fw_name = "edgeport/down3.bin"; struct edgeport_fw_hdr *fw_hdr; status = request_firmware(&fw, fw_name, dev); if (status) { dev_err(dev, "Failed to load image \"%s\" err %d\n", fw_name, status); return status; } if (check_fw_sanity(serial, fw)) { status = -EINVAL; goto out; } fw_hdr = (struct edgeport_fw_hdr *)fw->data; /* If on-board version is newer, "fw_version" will be updated later. */ serial->fw_version = (fw_hdr->major_version << 8) + fw_hdr->minor_version; /* * This routine is entered by both the BOOT mode and the Download mode * We can determine which code is running by the reading the config * descriptor and if we have only one bulk pipe it is in boot mode */ serial->product_info.hardware_type = HARDWARE_TYPE_TIUMP; /* Default to type 2 i2c */ serial->TI_I2C_Type = DTK_ADDR_SPACE_I2C_TYPE_II; status = choose_config(serial->serial->dev); if (status) goto out; interface = &serial->serial->interface->cur_altsetting->desc; if (!interface) { dev_err(dev, "%s - no interface set, error!\n", __func__); status = -ENODEV; goto out; } /* * Setup initial mode -- the default mode 0 is TI_MODE_CONFIGURING * if we have more than one endpoint we are definitely in download * mode */ if (interface->bNumEndpoints > 1) { serial->product_info.TiMode = TI_MODE_DOWNLOAD; status = do_download_mode(serial, fw); } else { /* Otherwise we will remain in configuring mode */ serial->product_info.TiMode = TI_MODE_CONFIGURING; status = do_boot_mode(serial, fw); } out: release_firmware(fw); return status; } static int do_download_mode(struct edgeport_serial *serial, const struct firmware *fw) { struct device *dev = &serial->serial->interface->dev; int status = 0; int start_address; struct edge_ti_manuf_descriptor *ti_manuf_desc; int download_cur_ver; int download_new_ver; struct edgeport_fw_hdr *fw_hdr = (struct edgeport_fw_hdr *)fw->data; struct ti_i2c_desc *rom_desc; dev_dbg(dev, "%s - RUNNING IN DOWNLOAD MODE\n", __func__); status = check_i2c_image(serial); if (status) { dev_dbg(dev, "%s - DOWNLOAD MODE -- BAD I2C\n", __func__); return status; } /* * Validate Hardware version number * Read Manufacturing Descriptor from TI Based Edgeport */ ti_manuf_desc = kmalloc(sizeof(*ti_manuf_desc), GFP_KERNEL); if (!ti_manuf_desc) return -ENOMEM; status = get_manuf_info(serial, (__u8 *)ti_manuf_desc); if (status) { kfree(ti_manuf_desc); return status; } /* Check version number of ION descriptor */ if (!ignore_cpu_rev && ti_cpu_rev(ti_manuf_desc) < 2) { dev_dbg(dev, "%s - Wrong CPU Rev %d (Must be 2)\n", __func__, ti_cpu_rev(ti_manuf_desc)); kfree(ti_manuf_desc); return -EINVAL; } rom_desc = kmalloc(sizeof(*rom_desc), GFP_KERNEL); if (!rom_desc) { kfree(ti_manuf_desc); return -ENOMEM; } /* Search for type 2 record (firmware record) */ start_address = get_descriptor_addr(serial, I2C_DESC_TYPE_FIRMWARE_BASIC, rom_desc); if (start_address != 0) { struct ti_i2c_firmware_rec *firmware_version; u8 *record; dev_dbg(dev, "%s - Found Type FIRMWARE (Type 2) record\n", __func__); firmware_version = kmalloc(sizeof(*firmware_version), GFP_KERNEL); if (!firmware_version) { kfree(rom_desc); kfree(ti_manuf_desc); return -ENOMEM; } /* * Validate version number * Read the descriptor data */ status = read_rom(serial, start_address + sizeof(struct ti_i2c_desc), sizeof(struct ti_i2c_firmware_rec), (__u8 *)firmware_version); if (status) { kfree(firmware_version); kfree(rom_desc); kfree(ti_manuf_desc); return status; } /* * Check version number of download with current * version in I2c */ download_cur_ver = (firmware_version->Ver_Major << 8) + (firmware_version->Ver_Minor); download_new_ver = (fw_hdr->major_version << 8) + (fw_hdr->minor_version); dev_dbg(dev, "%s - >> FW Versions Device %d.%d Driver %d.%d\n", __func__, firmware_version->Ver_Major, firmware_version->Ver_Minor, fw_hdr->major_version, fw_hdr->minor_version); /* * Check if we have an old version in the I2C and * update if necessary */ if (download_cur_ver < download_new_ver) { dev_dbg(dev, "%s - Update I2C dld from %d.%d to %d.%d\n", __func__, firmware_version->Ver_Major, firmware_version->Ver_Minor, fw_hdr->major_version, fw_hdr->minor_version); record = kmalloc(1, GFP_KERNEL); if (!record) { kfree(firmware_version); kfree(rom_desc); kfree(ti_manuf_desc); return -ENOMEM; } /* * In order to update the I2C firmware we must * change the type 2 record to type 0xF2. This * will force the UMP to come up in Boot Mode. * Then while in boot mode, the driver will * download the latest firmware (padded to * 15.5k) into the UMP ram. Finally when the * device comes back up in download mode the * driver will cause the new firmware to be * copied from the UMP Ram to I2C and the * firmware will update the record type from * 0xf2 to 0x02. */ *record = I2C_DESC_TYPE_FIRMWARE_BLANK; /* * Change the I2C Firmware record type to * 0xf2 to trigger an update */ status = write_rom(serial, start_address, sizeof(*record), record); if (status) { kfree(record); kfree(firmware_version); kfree(rom_desc); kfree(ti_manuf_desc); return status; } /* * verify the write -- must do this in order * for write to complete before we do the * hardware reset */ status = read_rom(serial, start_address, sizeof(*record), record); if (status) { kfree(record); kfree(firmware_version); kfree(rom_desc); kfree(ti_manuf_desc); return status; } if (*record != I2C_DESC_TYPE_FIRMWARE_BLANK) { dev_err(dev, "%s - error resetting device\n", __func__); kfree(record); kfree(firmware_version); kfree(rom_desc); kfree(ti_manuf_desc); return -ENODEV; } dev_dbg(dev, "%s - HARDWARE RESET\n", __func__); /* Reset UMP -- Back to BOOT MODE */ status = ti_vsend_sync(serial->serial->dev, UMPC_HARDWARE_RESET, 0, 0, NULL, 0, TI_VSEND_TIMEOUT_DEFAULT); dev_dbg(dev, "%s - HARDWARE RESET return %d\n", __func__, status); /* return an error on purpose. */ kfree(record); kfree(firmware_version); kfree(rom_desc); kfree(ti_manuf_desc); return -ENODEV; } /* Same or newer fw version is already loaded */ serial->fw_version = download_cur_ver; kfree(firmware_version); } /* Search for type 0xF2 record (firmware blank record) */ else { start_address = get_descriptor_addr(serial, I2C_DESC_TYPE_FIRMWARE_BLANK, rom_desc); if (start_address != 0) { #define HEADER_SIZE (sizeof(struct ti_i2c_desc) + \ sizeof(struct ti_i2c_firmware_rec)) __u8 *header; __u8 *vheader; header = kmalloc(HEADER_SIZE, GFP_KERNEL); if (!header) { kfree(rom_desc); kfree(ti_manuf_desc); return -ENOMEM; } vheader = kmalloc(HEADER_SIZE, GFP_KERNEL); if (!vheader) { kfree(header); kfree(rom_desc); kfree(ti_manuf_desc); return -ENOMEM; } dev_dbg(dev, "%s - Found Type BLANK FIRMWARE (Type F2) record\n", __func__); /* * In order to update the I2C firmware we must change * the type 2 record to type 0xF2. This will force the * UMP to come up in Boot Mode. Then while in boot * mode, the driver will download the latest firmware * (padded to 15.5k) into the UMP ram. Finally when the * device comes back up in download mode the driver * will cause the new firmware to be copied from the * UMP Ram to I2C and the firmware will update the * record type from 0xf2 to 0x02. */ status = build_i2c_fw_hdr(header, fw); if (status) { kfree(vheader); kfree(header); kfree(rom_desc); kfree(ti_manuf_desc); return -EINVAL; } /* * Update I2C with type 0xf2 record with correct * size and checksum */ status = write_rom(serial, start_address, HEADER_SIZE, header); if (status) { kfree(vheader); kfree(header); kfree(rom_desc); kfree(ti_manuf_desc); return -EINVAL; } /* * verify the write -- must do this in order for * write to complete before we do the hardware reset */ status = read_rom(serial, start_address, HEADER_SIZE, vheader); if (status) { dev_dbg(dev, "%s - can't read header back\n", __func__); kfree(vheader); kfree(header); kfree(rom_desc); kfree(ti_manuf_desc); return status; } if (memcmp(vheader, header, HEADER_SIZE)) { dev_dbg(dev, "%s - write download record failed\n", __func__); kfree(vheader); kfree(header); kfree(rom_desc); kfree(ti_manuf_desc); return -EINVAL; } kfree(vheader); kfree(header); dev_dbg(dev, "%s - Start firmware update\n", __func__); /* Tell firmware to copy download image into I2C */ status = ti_vsend_sync(serial->serial->dev, UMPC_COPY_DNLD_TO_I2C, 0, 0, NULL, 0, TI_VSEND_TIMEOUT_FW_DOWNLOAD); dev_dbg(dev, "%s - Update complete 0x%x\n", __func__, status); if (status) { dev_err(dev, "%s - UMPC_COPY_DNLD_TO_I2C failed\n", __func__); kfree(rom_desc); kfree(ti_manuf_desc); return status; } } } /* The device is running the download code */ kfree(rom_desc); kfree(ti_manuf_desc); return 0; } static int do_boot_mode(struct edgeport_serial *serial, const struct firmware *fw) { struct device *dev = &serial->serial->interface->dev; int status = 0; struct edge_ti_manuf_descriptor *ti_manuf_desc; struct edgeport_fw_hdr *fw_hdr = (struct edgeport_fw_hdr *)fw->data; dev_dbg(dev, "%s - RUNNING IN BOOT MODE\n", __func__); /* Configure the TI device so we can use the BULK pipes for download */ status = config_boot_dev(serial->serial->dev); if (status) return status; if (le16_to_cpu(serial->serial->dev->descriptor.idVendor) != USB_VENDOR_ID_ION) { dev_dbg(dev, "%s - VID = 0x%x\n", __func__, le16_to_cpu(serial->serial->dev->descriptor.idVendor)); serial->TI_I2C_Type = DTK_ADDR_SPACE_I2C_TYPE_II; goto stayinbootmode; } /* * We have an ION device (I2c Must be programmed) * Determine I2C image type */ if (i2c_type_bootmode(serial)) goto stayinbootmode; /* Check for ION Vendor ID and that the I2C is valid */ if (!check_i2c_image(serial)) { struct ti_i2c_image_header *header; int i; __u8 cs = 0; __u8 *buffer; int buffer_size; /* * Validate Hardware version number * Read Manufacturing Descriptor from TI Based Edgeport */ ti_manuf_desc = kmalloc(sizeof(*ti_manuf_desc), GFP_KERNEL); if (!ti_manuf_desc) return -ENOMEM; status = get_manuf_info(serial, (__u8 *)ti_manuf_desc); if (status) { kfree(ti_manuf_desc); goto stayinbootmode; } /* Check for version 2 */ if (!ignore_cpu_rev && ti_cpu_rev(ti_manuf_desc) < 2) { dev_dbg(dev, "%s - Wrong CPU Rev %d (Must be 2)\n", __func__, ti_cpu_rev(ti_manuf_desc)); kfree(ti_manuf_desc); goto stayinbootmode; } kfree(ti_manuf_desc); /* * In order to update the I2C firmware we must change the type * 2 record to type 0xF2. This will force the UMP to come up * in Boot Mode. Then while in boot mode, the driver will * download the latest firmware (padded to 15.5k) into the * UMP ram. Finally when the device comes back up in download * mode the driver will cause the new firmware to be copied * from the UMP Ram to I2C and the firmware will update the * record type from 0xf2 to 0x02. * * Do we really have to copy the whole firmware image, * or could we do this in place! */ /* Allocate a 15.5k buffer + 3 byte header */ buffer_size = (((1024 * 16) - 512) + sizeof(struct ti_i2c_image_header)); buffer = kmalloc(buffer_size, GFP_KERNEL); if (!buffer) return -ENOMEM; /* Initialize the buffer to 0xff (pad the buffer) */ memset(buffer, 0xff, buffer_size); memcpy(buffer, &fw->data[4], fw->size - 4); for (i = sizeof(struct ti_i2c_image_header); i < buffer_size; i++) { cs = (__u8)(cs + buffer[i]); } header = (struct ti_i2c_image_header *)buffer; /* update length and checksum after padding */ header->Length = cpu_to_le16((__u16)(buffer_size - sizeof(struct ti_i2c_image_header))); header->CheckSum = cs; /* Download the operational code */ dev_dbg(dev, "%s - Downloading operational code image version %d.%d (TI UMP)\n", __func__, fw_hdr->major_version, fw_hdr->minor_version); status = download_code(serial, buffer, buffer_size); kfree(buffer); if (status) { dev_dbg(dev, "%s - Error downloading operational code image\n", __func__); return status; } /* Device will reboot */ serial->product_info.TiMode = TI_MODE_TRANSITIONING; dev_dbg(dev, "%s - Download successful -- Device rebooting...\n", __func__); return 1; } stayinbootmode: /* Eprom is invalid or blank stay in boot mode */ dev_dbg(dev, "%s - STAYING IN BOOT MODE\n", __func__); serial->product_info.TiMode = TI_MODE_BOOT; return 1; } static int ti_do_config(struct edgeport_port *port, int feature, int on) { int port_number = port->port->port_number; on = !!on; /* 1 or 0 not bitmask */ return send_cmd(port->port->serial->dev, feature, (__u8)(UMPM_UART1_PORT + port_number), on, NULL, 0); } static int restore_mcr(struct edgeport_port *port, __u8 mcr) { int status = 0; dev_dbg(&port->port->dev, "%s - %x\n", __func__, mcr); status = ti_do_config(port, UMPC_SET_CLR_DTR, mcr & MCR_DTR); if (status) return status; status = ti_do_config(port, UMPC_SET_CLR_RTS, mcr & MCR_RTS); if (status) return status; return ti_do_config(port, UMPC_SET_CLR_LOOPBACK, mcr & MCR_LOOPBACK); } /* Convert TI LSR to standard UART flags */ static __u8 map_line_status(__u8 ti_lsr) { __u8 lsr = 0; #define MAP_FLAG(flagUmp, flagUart) \ if (ti_lsr & flagUmp) \ lsr |= flagUart; MAP_FLAG(UMP_UART_LSR_OV_MASK, LSR_OVER_ERR) /* overrun */ MAP_FLAG(UMP_UART_LSR_PE_MASK, LSR_PAR_ERR) /* parity error */ MAP_FLAG(UMP_UART_LSR_FE_MASK, LSR_FRM_ERR) /* framing error */ MAP_FLAG(UMP_UART_LSR_BR_MASK, LSR_BREAK) /* break detected */ MAP_FLAG(UMP_UART_LSR_RX_MASK, LSR_RX_AVAIL) /* rx data available */ MAP_FLAG(UMP_UART_LSR_TX_MASK, LSR_TX_EMPTY) /* tx hold reg empty */ #undef MAP_FLAG return lsr; } static void handle_new_msr(struct edgeport_port *edge_port, __u8 msr) { struct async_icount *icount; struct tty_struct *tty; dev_dbg(&edge_port->port->dev, "%s - %02x\n", __func__, msr); if (msr & (EDGEPORT_MSR_DELTA_CTS | EDGEPORT_MSR_DELTA_DSR | EDGEPORT_MSR_DELTA_RI | EDGEPORT_MSR_DELTA_CD)) { icount = &edge_port->port->icount; /* update input line counters */ if (msr & EDGEPORT_MSR_DELTA_CTS) icount->cts++; if (msr & EDGEPORT_MSR_DELTA_DSR) icount->dsr++; if (msr & EDGEPORT_MSR_DELTA_CD) icount->dcd++; if (msr & EDGEPORT_MSR_DELTA_RI) icount->rng++; wake_up_interruptible(&edge_port->port->port.delta_msr_wait); } /* Save the new modem status */ edge_port->shadow_msr = msr & 0xf0; tty = tty_port_tty_get(&edge_port->port->port); /* handle CTS flow control */ if (tty && C_CRTSCTS(tty)) { if (msr & EDGEPORT_MSR_CTS) tty_wakeup(tty); } tty_kref_put(tty); } static void handle_new_lsr(struct edgeport_port *edge_port, int lsr_data, __u8 lsr, __u8 data) { struct async_icount *icount; __u8 new_lsr = (__u8)(lsr & (__u8)(LSR_OVER_ERR | LSR_PAR_ERR | LSR_FRM_ERR | LSR_BREAK)); dev_dbg(&edge_port->port->dev, "%s - %02x\n", __func__, new_lsr); edge_port->shadow_lsr = lsr; if (new_lsr & LSR_BREAK) /* * Parity and Framing errors only count if they * occur exclusive of a break being received. */ new_lsr &= (__u8)(LSR_OVER_ERR | LSR_BREAK); /* Place LSR data byte into Rx buffer */ if (lsr_data) edge_tty_recv(edge_port->port, &data, 1); /* update input line counters */ icount = &edge_port->port->icount; if (new_lsr & LSR_BREAK) icount->brk++; if (new_lsr & LSR_OVER_ERR) icount->overrun++; if (new_lsr & LSR_PAR_ERR) icount->parity++; if (new_lsr & LSR_FRM_ERR) icount->frame++; } static void edge_interrupt_callback(struct urb *urb) { struct edgeport_serial *edge_serial = urb->context; struct usb_serial_port *port; struct edgeport_port *edge_port; struct device *dev; unsigned char *data = urb->transfer_buffer; int length = urb->actual_length; int port_number; int function; int retval; __u8 lsr; __u8 msr; int status = urb->status; switch (status) { case 0: /* success */ break; case -ECONNRESET: case -ENOENT: case -ESHUTDOWN: /* this urb is terminated, clean up */ dev_dbg(&urb->dev->dev, "%s - urb shutting down with status: %d\n", __func__, status); return; default: dev_err(&urb->dev->dev, "%s - nonzero urb status received: " "%d\n", __func__, status); goto exit; } if (!length) { dev_dbg(&urb->dev->dev, "%s - no data in urb\n", __func__); goto exit; } dev = &edge_serial->serial->dev->dev; usb_serial_debug_data(dev, __func__, length, data); if (length != 2) { dev_dbg(dev, "%s - expecting packet of size 2, got %d\n", __func__, length); goto exit; } port_number = TIUMP_GET_PORT_FROM_CODE(data[0]); function = TIUMP_GET_FUNC_FROM_CODE(data[0]); dev_dbg(dev, "%s - port_number %d, function %d, info 0x%x\n", __func__, port_number, function, data[1]); if (port_number >= edge_serial->serial->num_ports) { dev_err(dev, "bad port number %d\n", port_number); goto exit; } port = edge_serial->serial->port[port_number]; edge_port = usb_get_serial_port_data(port); if (!edge_port) { dev_dbg(dev, "%s - edge_port not found\n", __func__); return; } switch (function) { case TIUMP_INTERRUPT_CODE_LSR: lsr = map_line_status(data[1]); if (lsr & UMP_UART_LSR_DATA_MASK) { /* * Save the LSR event for bulk read completion routine */ dev_dbg(dev, "%s - LSR Event Port %u LSR Status = %02x\n", __func__, port_number, lsr); edge_port->lsr_event = 1; edge_port->lsr_mask = lsr; } else { dev_dbg(dev, "%s - ===== Port %d LSR Status = %02x ======\n", __func__, port_number, lsr); handle_new_lsr(edge_port, 0, lsr, 0); } break; case TIUMP_INTERRUPT_CODE_MSR: /* MSR */ /* Copy MSR from UMP */ msr = data[1]; dev_dbg(dev, "%s - ===== Port %u MSR Status = %02x ======\n", __func__, port_number, msr); handle_new_msr(edge_port, msr); break; default: dev_err(&urb->dev->dev, "%s - Unknown Interrupt code from UMP %x\n", __func__, data[1]); break; } exit: retval = usb_submit_urb(urb, GFP_ATOMIC); if (retval) dev_err(&urb->dev->dev, "%s - usb_submit_urb failed with result %d\n", __func__, retval); } static void edge_bulk_in_callback(struct urb *urb) { struct edgeport_port *edge_port = urb->context; struct device *dev = &edge_port->port->dev; unsigned char *data = urb->transfer_buffer; int retval = 0; int port_number; int status = urb->status; switch (status) { case 0: /* success */ break; case -ECONNRESET: case -ENOENT: case -ESHUTDOWN: /* this urb is terminated, clean up */ dev_dbg(&urb->dev->dev, "%s - urb shutting down with status: %d\n", __func__, status); return; default: dev_err(&urb->dev->dev, "%s - nonzero read bulk status received: %d\n", __func__, status); } if (status == -EPIPE) goto exit; if (status) { dev_err(&urb->dev->dev, "%s - stopping read!\n", __func__); return; } port_number = edge_port->port->port_number; if (urb->actual_length > 0 && edge_port->lsr_event) { edge_port->lsr_event = 0; dev_dbg(dev, "%s ===== Port %u LSR Status = %02x, Data = %02x ======\n", __func__, port_number, edge_port->lsr_mask, *data); handle_new_lsr(edge_port, 1, edge_port->lsr_mask, *data); /* Adjust buffer length/pointer */ --urb->actual_length; ++data; } if (urb->actual_length) { usb_serial_debug_data(dev, __func__, urb->actual_length, data); if (edge_port->close_pending) dev_dbg(dev, "%s - close pending, dropping data on the floor\n", __func__); else edge_tty_recv(edge_port->port, data, urb->actual_length); edge_port->port->icount.rx += urb->actual_length; } exit: /* continue read unless stopped */ spin_lock(&edge_port->ep_lock); if (edge_port->ep_read_urb_state == EDGE_READ_URB_RUNNING) retval = usb_submit_urb(urb, GFP_ATOMIC); else if (edge_port->ep_read_urb_state == EDGE_READ_URB_STOPPING) edge_port->ep_read_urb_state = EDGE_READ_URB_STOPPED; spin_unlock(&edge_port->ep_lock); if (retval) dev_err(dev, "%s - usb_submit_urb failed with result %d\n", __func__, retval); } static void edge_tty_recv(struct usb_serial_port *port, unsigned char *data, int length) { int queued; queued = tty_insert_flip_string(&port->port, data, length); if (queued < length) dev_err(&port->dev, "%s - dropping data, %d bytes lost\n", __func__, length - queued); tty_flip_buffer_push(&port->port); } static void edge_bulk_out_callback(struct urb *urb) { struct usb_serial_port *port = urb->context; struct edgeport_port *edge_port = usb_get_serial_port_data(port); int status = urb->status; struct tty_struct *tty; edge_port->ep_write_urb_in_use = 0; switch (status) { case 0: /* success */ break; case -ECONNRESET: case -ENOENT: case -ESHUTDOWN: /* this urb is terminated, clean up */ dev_dbg(&urb->dev->dev, "%s - urb shutting down with status: %d\n", __func__, status); return; default: dev_err_console(port, "%s - nonzero write bulk status " "received: %d\n", __func__, status); } /* send any buffered data */ tty = tty_port_tty_get(&port->port); edge_send(port, tty); tty_kref_put(tty); } static int edge_open(struct tty_struct *tty, struct usb_serial_port *port) { struct edgeport_port *edge_port = usb_get_serial_port_data(port); struct edgeport_serial *edge_serial; struct usb_device *dev; struct urb *urb; int port_number; int status; u16 open_settings; u8 transaction_timeout; if (edge_port == NULL) return -ENODEV; port_number = port->port_number; dev = port->serial->dev; /* turn off loopback */ status = ti_do_config(edge_port, UMPC_SET_CLR_LOOPBACK, 0); if (status) { dev_err(&port->dev, "%s - cannot send clear loopback command, %d\n", __func__, status); return status; } /* set up the port settings */ if (tty) edge_set_termios(tty, port, &tty->termios); /* open up the port */ /* milliseconds to timeout for DMA transfer */ transaction_timeout = 2; edge_port->ump_read_timeout = max(20, ((transaction_timeout * 3) / 2)); /* milliseconds to timeout for DMA transfer */ open_settings = (u8)(UMP_DMA_MODE_CONTINOUS | UMP_PIPE_TRANS_TIMEOUT_ENA | (transaction_timeout << 2)); dev_dbg(&port->dev, "%s - Sending UMPC_OPEN_PORT\n", __func__); /* Tell TI to open and start the port */ status = send_cmd(dev, UMPC_OPEN_PORT, (u8)(UMPM_UART1_PORT + port_number), open_settings, NULL, 0); if (status) { dev_err(&port->dev, "%s - cannot send open command, %d\n", __func__, status); return status; } /* Start the DMA? */ status = send_cmd(dev, UMPC_START_PORT, (u8)(UMPM_UART1_PORT + port_number), 0, NULL, 0); if (status) { dev_err(&port->dev, "%s - cannot send start DMA command, %d\n", __func__, status); return status; } /* Clear TX and RX buffers in UMP */ status = purge_port(port, UMP_PORT_DIR_OUT | UMP_PORT_DIR_IN); if (status) { dev_err(&port->dev, "%s - cannot send clear buffers command, %d\n", __func__, status); return status; } /* Read Initial MSR */ status = ti_vread_sync(dev, UMPC_READ_MSR, 0, (__u16)(UMPM_UART1_PORT + port_number), &edge_port->shadow_msr, 1); if (status) { dev_err(&port->dev, "%s - cannot send read MSR command, %d\n", __func__, status); return status; } dev_dbg(&port->dev, "ShadowMSR 0x%X\n", edge_port->shadow_msr); /* Set Initial MCR */ edge_port->shadow_mcr = MCR_RTS | MCR_DTR; dev_dbg(&port->dev, "ShadowMCR 0x%X\n", edge_port->shadow_mcr); edge_serial = edge_port->edge_serial; if (mutex_lock_interruptible(&edge_serial->es_lock)) return -ERESTARTSYS; if (edge_serial->num_ports_open == 0) { /* we are the first port to open, post the interrupt urb */ urb = edge_serial->serial->port[0]->interrupt_in_urb; if (!urb) { dev_err(&port->dev, "%s - no interrupt urb present, exiting\n", __func__); status = -EINVAL; goto release_es_lock; } urb->context = edge_serial; status = usb_submit_urb(urb, GFP_KERNEL); if (status) { dev_err(&port->dev, "%s - usb_submit_urb failed with value %d\n", __func__, status); goto release_es_lock; } } /* * reset the data toggle on the bulk endpoints to work around bug in * host controllers where things get out of sync some times */ usb_clear_halt(dev, port->write_urb->pipe); usb_clear_halt(dev, port->read_urb->pipe); /* start up our bulk read urb */ urb = port->read_urb; if (!urb) { dev_err(&port->dev, "%s - no read urb present, exiting\n", __func__); status = -EINVAL; goto unlink_int_urb; } edge_port->ep_read_urb_state = EDGE_READ_URB_RUNNING; urb->context = edge_port; status = usb_submit_urb(urb, GFP_KERNEL); if (status) { dev_err(&port->dev, "%s - read bulk usb_submit_urb failed with value %d\n", __func__, status); goto unlink_int_urb; } ++edge_serial->num_ports_open; goto release_es_lock; unlink_int_urb: if (edge_port->edge_serial->num_ports_open == 0) usb_kill_urb(port->serial->port[0]->interrupt_in_urb); release_es_lock: mutex_unlock(&edge_serial->es_lock); return status; } static void edge_close(struct usb_serial_port *port) { struct edgeport_serial *edge_serial; struct edgeport_port *edge_port; struct usb_serial *serial = port->serial; unsigned long flags; int port_number; edge_serial = usb_get_serial_data(port->serial); edge_port = usb_get_serial_port_data(port); if (edge_serial == NULL || edge_port == NULL) return; /* * The bulkreadcompletion routine will check * this flag and dump add read data */ edge_port->close_pending = 1; usb_kill_urb(port->read_urb); usb_kill_urb(port->write_urb); edge_port->ep_write_urb_in_use = 0; spin_lock_irqsave(&edge_port->ep_lock, flags); kfifo_reset_out(&port->write_fifo); spin_unlock_irqrestore(&edge_port->ep_lock, flags); dev_dbg(&port->dev, "%s - send umpc_close_port\n", __func__); port_number = port->port_number; send_cmd(serial->dev, UMPC_CLOSE_PORT, (__u8)(UMPM_UART1_PORT + port_number), 0, NULL, 0); mutex_lock(&edge_serial->es_lock); --edge_port->edge_serial->num_ports_open; if (edge_port->edge_serial->num_ports_open <= 0) { /* last port is now closed, let's shut down our interrupt urb */ usb_kill_urb(port->serial->port[0]->interrupt_in_urb); edge_port->edge_serial->num_ports_open = 0; } mutex_unlock(&edge_serial->es_lock); edge_port->close_pending = 0; } static int edge_write(struct tty_struct *tty, struct usb_serial_port *port, const unsigned char *data, int count) { struct edgeport_port *edge_port = usb_get_serial_port_data(port); if (count == 0) { dev_dbg(&port->dev, "%s - write request of 0 bytes\n", __func__); return 0; } if (edge_port == NULL) return -ENODEV; if (edge_port->close_pending == 1) return -ENODEV; count = kfifo_in_locked(&port->write_fifo, data, count, &edge_port->ep_lock); edge_send(port, tty); return count; } static void edge_send(struct usb_serial_port *port, struct tty_struct *tty) { int count, result; struct edgeport_port *edge_port = usb_get_serial_port_data(port); unsigned long flags; spin_lock_irqsave(&edge_port->ep_lock, flags); if (edge_port->ep_write_urb_in_use) { spin_unlock_irqrestore(&edge_port->ep_lock, flags); return; } count = kfifo_out(&port->write_fifo, port->write_urb->transfer_buffer, port->bulk_out_size); if (count == 0) { spin_unlock_irqrestore(&edge_port->ep_lock, flags); return; } edge_port->ep_write_urb_in_use = 1; spin_unlock_irqrestore(&edge_port->ep_lock, flags); usb_serial_debug_data(&port->dev, __func__, count, port->write_urb->transfer_buffer); /* set up our urb */ port->write_urb->transfer_buffer_length = count; /* send the data out the bulk port */ result = usb_submit_urb(port->write_urb, GFP_ATOMIC); if (result) { dev_err_console(port, "%s - failed submitting write urb, error %d\n", __func__, result); edge_port->ep_write_urb_in_use = 0; /* TODO: reschedule edge_send */ } else edge_port->port->icount.tx += count; /* * wakeup any process waiting for writes to complete * there is now more room in the buffer for new writes */ if (tty) tty_wakeup(tty); } static int edge_write_room(struct tty_struct *tty) { struct usb_serial_port *port = tty->driver_data; struct edgeport_port *edge_port = usb_get_serial_port_data(port); int room = 0; unsigned long flags; if (edge_port == NULL) return 0; if (edge_port->close_pending == 1) return 0; spin_lock_irqsave(&edge_port->ep_lock, flags); room = kfifo_avail(&port->write_fifo); spin_unlock_irqrestore(&edge_port->ep_lock, flags); dev_dbg(&port->dev, "%s - returns %d\n", __func__, room); return room; } static int edge_chars_in_buffer(struct tty_struct *tty) { struct usb_serial_port *port = tty->driver_data; struct edgeport_port *edge_port = usb_get_serial_port_data(port); int chars = 0; unsigned long flags; if (edge_port == NULL) return 0; spin_lock_irqsave(&edge_port->ep_lock, flags); chars = kfifo_len(&port->write_fifo); spin_unlock_irqrestore(&edge_port->ep_lock, flags); dev_dbg(&port->dev, "%s - returns %d\n", __func__, chars); return chars; } static bool edge_tx_empty(struct usb_serial_port *port) { struct edgeport_port *edge_port = usb_get_serial_port_data(port); int ret; ret = tx_active(edge_port); if (ret > 0) return false; return true; } static void edge_throttle(struct tty_struct *tty) { struct usb_serial_port *port = tty->driver_data; struct edgeport_port *edge_port = usb_get_serial_port_data(port); int status; if (edge_port == NULL) return; /* if we are implementing XON/XOFF, send the stop character */ if (I_IXOFF(tty)) { unsigned char stop_char = STOP_CHAR(tty); status = edge_write(tty, port, &stop_char, 1); if (status <= 0) { dev_err(&port->dev, "%s - failed to write stop character, %d\n", __func__, status); } } /* * if we are implementing RTS/CTS, stop reads * and the Edgeport will clear the RTS line */ if (C_CRTSCTS(tty)) stop_read(edge_port); } static void edge_unthrottle(struct tty_struct *tty) { struct usb_serial_port *port = tty->driver_data; struct edgeport_port *edge_port = usb_get_serial_port_data(port); int status; if (edge_port == NULL) return; /* if we are implementing XON/XOFF, send the start character */ if (I_IXOFF(tty)) { unsigned char start_char = START_CHAR(tty); status = edge_write(tty, port, &start_char, 1); if (status <= 0) { dev_err(&port->dev, "%s - failed to write start character, %d\n", __func__, status); } } /* * if we are implementing RTS/CTS, restart reads * are the Edgeport will assert the RTS line */ if (C_CRTSCTS(tty)) { status = restart_read(edge_port); if (status) dev_err(&port->dev, "%s - read bulk usb_submit_urb failed: %d\n", __func__, status); } } static void stop_read(struct edgeport_port *edge_port) { unsigned long flags; spin_lock_irqsave(&edge_port->ep_lock, flags); if (edge_port->ep_read_urb_state == EDGE_READ_URB_RUNNING) edge_port->ep_read_urb_state = EDGE_READ_URB_STOPPING; edge_port->shadow_mcr &= ~MCR_RTS; spin_unlock_irqrestore(&edge_port->ep_lock, flags); } static int restart_read(struct edgeport_port *edge_port) { struct urb *urb; int status = 0; unsigned long flags; spin_lock_irqsave(&edge_port->ep_lock, flags); if (edge_port->ep_read_urb_state == EDGE_READ_URB_STOPPED) { urb = edge_port->port->read_urb; status = usb_submit_urb(urb, GFP_ATOMIC); } edge_port->ep_read_urb_state = EDGE_READ_URB_RUNNING; edge_port->shadow_mcr |= MCR_RTS; spin_unlock_irqrestore(&edge_port->ep_lock, flags); return status; } static void change_port_settings(struct tty_struct *tty, struct edgeport_port *edge_port, struct ktermios *old_termios) { struct device *dev = &edge_port->port->dev; struct ump_uart_config *config; int baud; unsigned cflag; int status; int port_number = edge_port->port->port_number; config = kmalloc (sizeof (*config), GFP_KERNEL); if (!config) { tty->termios = *old_termios; return; } cflag = tty->termios.c_cflag; config->wFlags = 0; /* These flags must be set */ config->wFlags |= UMP_MASK_UART_FLAGS_RECEIVE_MS_INT; config->wFlags |= UMP_MASK_UART_FLAGS_AUTO_START_ON_ERR; config->bUartMode = (__u8)(edge_port->bUartMode); switch (cflag & CSIZE) { case CS5: config->bDataBits = UMP_UART_CHAR5BITS; dev_dbg(dev, "%s - data bits = 5\n", __func__); break; case CS6: config->bDataBits = UMP_UART_CHAR6BITS; dev_dbg(dev, "%s - data bits = 6\n", __func__); break; case CS7: config->bDataBits = UMP_UART_CHAR7BITS; dev_dbg(dev, "%s - data bits = 7\n", __func__); break; default: case CS8: config->bDataBits = UMP_UART_CHAR8BITS; dev_dbg(dev, "%s - data bits = 8\n", __func__); break; } if (cflag & PARENB) { if (cflag & PARODD) { config->wFlags |= UMP_MASK_UART_FLAGS_PARITY; config->bParity = UMP_UART_ODDPARITY; dev_dbg(dev, "%s - parity = odd\n", __func__); } else { config->wFlags |= UMP_MASK_UART_FLAGS_PARITY; config->bParity = UMP_UART_EVENPARITY; dev_dbg(dev, "%s - parity = even\n", __func__); } } else { config->bParity = UMP_UART_NOPARITY; dev_dbg(dev, "%s - parity = none\n", __func__); } if (cflag & CSTOPB) { config->bStopBits = UMP_UART_STOPBIT2; dev_dbg(dev, "%s - stop bits = 2\n", __func__); } else { config->bStopBits = UMP_UART_STOPBIT1; dev_dbg(dev, "%s - stop bits = 1\n", __func__); } /* figure out the flow control settings */ if (cflag & CRTSCTS) { config->wFlags |= UMP_MASK_UART_FLAGS_OUT_X_CTS_FLOW; config->wFlags |= UMP_MASK_UART_FLAGS_RTS_FLOW; dev_dbg(dev, "%s - RTS/CTS is enabled\n", __func__); } else { dev_dbg(dev, "%s - RTS/CTS is disabled\n", __func__); restart_read(edge_port); } /* * if we are implementing XON/XOFF, set the start and stop * character in the device */ config->cXon = START_CHAR(tty); config->cXoff = STOP_CHAR(tty); /* if we are implementing INBOUND XON/XOFF */ if (I_IXOFF(tty)) { config->wFlags |= UMP_MASK_UART_FLAGS_IN_X; dev_dbg(dev, "%s - INBOUND XON/XOFF is enabled, XON = %2x, XOFF = %2x\n", __func__, config->cXon, config->cXoff); } else dev_dbg(dev, "%s - INBOUND XON/XOFF is disabled\n", __func__); /* if we are implementing OUTBOUND XON/XOFF */ if (I_IXON(tty)) { config->wFlags |= UMP_MASK_UART_FLAGS_OUT_X; dev_dbg(dev, "%s - OUTBOUND XON/XOFF is enabled, XON = %2x, XOFF = %2x\n", __func__, config->cXon, config->cXoff); } else dev_dbg(dev, "%s - OUTBOUND XON/XOFF is disabled\n", __func__); tty->termios.c_cflag &= ~CMSPAR; /* Round the baud rate */ baud = tty_get_baud_rate(tty); if (!baud) { /* pick a default, any default... */ baud = 9600; } else { /* Avoid a zero divisor. */ baud = min(baud, 461550); tty_encode_baud_rate(tty, baud, baud); } edge_port->baud_rate = baud; config->wBaudRate = (__u16)((461550L + baud/2) / baud); /* FIXME: Recompute actual baud from divisor here */ dev_dbg(dev, "%s - baud rate = %d, wBaudRate = %d\n", __func__, baud, config->wBaudRate); dev_dbg(dev, "wBaudRate: %d\n", (int)(461550L / config->wBaudRate)); dev_dbg(dev, "wFlags: 0x%x\n", config->wFlags); dev_dbg(dev, "bDataBits: %d\n", config->bDataBits); dev_dbg(dev, "bParity: %d\n", config->bParity); dev_dbg(dev, "bStopBits: %d\n", config->bStopBits); dev_dbg(dev, "cXon: %d\n", config->cXon); dev_dbg(dev, "cXoff: %d\n", config->cXoff); dev_dbg(dev, "bUartMode: %d\n", config->bUartMode); /* move the word values into big endian mode */ cpu_to_be16s(&config->wFlags); cpu_to_be16s(&config->wBaudRate); status = send_cmd(edge_port->port->serial->dev, UMPC_SET_CONFIG, (__u8)(UMPM_UART1_PORT + port_number), 0, (__u8 *)config, sizeof(*config)); if (status) dev_dbg(dev, "%s - error %d when trying to write config to device\n", __func__, status); kfree(config); } static void edge_set_termios(struct tty_struct *tty, struct usb_serial_port *port, struct ktermios *old_termios) { struct edgeport_port *edge_port = usb_get_serial_port_data(port); unsigned int cflag; cflag = tty->termios.c_cflag; dev_dbg(&port->dev, "%s - clfag %08x iflag %08x\n", __func__, tty->termios.c_cflag, tty->termios.c_iflag); dev_dbg(&port->dev, "%s - old clfag %08x old iflag %08x\n", __func__, old_termios->c_cflag, old_termios->c_iflag); if (edge_port == NULL) return; /* change the port settings to the new ones specified */ change_port_settings(tty, edge_port, old_termios); } static int edge_tiocmset(struct tty_struct *tty, unsigned int set, unsigned int clear) { struct usb_serial_port *port = tty->driver_data; struct edgeport_port *edge_port = usb_get_serial_port_data(port); unsigned int mcr; unsigned long flags; spin_lock_irqsave(&edge_port->ep_lock, flags); mcr = edge_port->shadow_mcr; if (set & TIOCM_RTS) mcr |= MCR_RTS; if (set & TIOCM_DTR) mcr |= MCR_DTR; if (set & TIOCM_LOOP) mcr |= MCR_LOOPBACK; if (clear & TIOCM_RTS) mcr &= ~MCR_RTS; if (clear & TIOCM_DTR) mcr &= ~MCR_DTR; if (clear & TIOCM_LOOP) mcr &= ~MCR_LOOPBACK; edge_port->shadow_mcr = mcr; spin_unlock_irqrestore(&edge_port->ep_lock, flags); restore_mcr(edge_port, mcr); return 0; } static int edge_tiocmget(struct tty_struct *tty) { struct usb_serial_port *port = tty->driver_data; struct edgeport_port *edge_port = usb_get_serial_port_data(port); unsigned int result = 0; unsigned int msr; unsigned int mcr; unsigned long flags; spin_lock_irqsave(&edge_port->ep_lock, flags); msr = edge_port->shadow_msr; mcr = edge_port->shadow_mcr; result = ((mcr & MCR_DTR) ? TIOCM_DTR: 0) /* 0x002 */ | ((mcr & MCR_RTS) ? TIOCM_RTS: 0) /* 0x004 */ | ((msr & EDGEPORT_MSR_CTS) ? TIOCM_CTS: 0) /* 0x020 */ | ((msr & EDGEPORT_MSR_CD) ? TIOCM_CAR: 0) /* 0x040 */ | ((msr & EDGEPORT_MSR_RI) ? TIOCM_RI: 0) /* 0x080 */ | ((msr & EDGEPORT_MSR_DSR) ? TIOCM_DSR: 0); /* 0x100 */ dev_dbg(&port->dev, "%s -- %x\n", __func__, result); spin_unlock_irqrestore(&edge_port->ep_lock, flags); return result; } static int get_serial_info(struct edgeport_port *edge_port, struct serial_struct __user *retinfo) { struct serial_struct tmp; unsigned cwait; if (!retinfo) return -EFAULT; cwait = edge_port->port->port.closing_wait; if (cwait != ASYNC_CLOSING_WAIT_NONE) cwait = jiffies_to_msecs(cwait) / 10; memset(&tmp, 0, sizeof(tmp)); tmp.type = PORT_16550A; tmp.line = edge_port->port->minor; tmp.port = edge_port->port->port_number; tmp.irq = 0; tmp.flags = ASYNC_SKIP_TEST | ASYNC_AUTO_IRQ; tmp.xmit_fifo_size = edge_port->port->bulk_out_size; tmp.baud_base = 9600; tmp.close_delay = 5*HZ; tmp.closing_wait = cwait; if (copy_to_user(retinfo, &tmp, sizeof(*retinfo))) return -EFAULT; return 0; } static int edge_ioctl(struct tty_struct *tty, unsigned int cmd, unsigned long arg) { struct usb_serial_port *port = tty->driver_data; struct edgeport_port *edge_port = usb_get_serial_port_data(port); switch (cmd) { case TIOCGSERIAL: dev_dbg(&port->dev, "%s - TIOCGSERIAL\n", __func__); return get_serial_info(edge_port, (struct serial_struct __user *) arg); } return -ENOIOCTLCMD; } static void edge_break(struct tty_struct *tty, int break_state) { struct usb_serial_port *port = tty->driver_data; struct edgeport_port *edge_port = usb_get_serial_port_data(port); int status; int bv = 0; /* Off */ if (break_state == -1) bv = 1; /* On */ status = ti_do_config(edge_port, UMPC_SET_CLR_BREAK, bv); if (status) dev_dbg(&port->dev, "%s - error %d sending break set/clear command.\n", __func__, status); } static void edge_heartbeat_schedule(struct edgeport_serial *edge_serial) { if (!edge_serial->use_heartbeat) return; schedule_delayed_work(&edge_serial->heartbeat_work, FW_HEARTBEAT_SECS * HZ); } static void edge_heartbeat_work(struct work_struct *work) { struct edgeport_serial *serial; struct ti_i2c_desc *rom_desc; serial = container_of(work, struct edgeport_serial, heartbeat_work.work); rom_desc = kmalloc(sizeof(*rom_desc), GFP_KERNEL); /* Descriptor address request is enough to reset the firmware timer */ if (!rom_desc || !get_descriptor_addr(serial, I2C_DESC_TYPE_ION, rom_desc)) { dev_err(&serial->serial->interface->dev, "%s - Incomplete heartbeat\n", __func__); } kfree(rom_desc); edge_heartbeat_schedule(serial); } static int edge_startup(struct usb_serial *serial) { struct edgeport_serial *edge_serial; int status; u16 product_id; /* Make sure we have the required endpoints when in download mode. */ if (serial->interface->cur_altsetting->desc.bNumEndpoints > 1) { if (serial->num_bulk_in < serial->num_ports || serial->num_bulk_out < serial->num_ports) return -ENODEV; } /* create our private serial structure */ edge_serial = kzalloc(sizeof(struct edgeport_serial), GFP_KERNEL); if (!edge_serial) return -ENOMEM; mutex_init(&edge_serial->es_lock); edge_serial->serial = serial; INIT_DELAYED_WORK(&edge_serial->heartbeat_work, edge_heartbeat_work); usb_set_serial_data(serial, edge_serial); status = download_fw(edge_serial); if (status < 0) { kfree(edge_serial); return status; } if (status > 0) return 1; /* bind but do not register any ports */ product_id = le16_to_cpu( edge_serial->serial->dev->descriptor.idProduct); /* Currently only the EP/416 models require heartbeat support */ if (edge_serial->fw_version > FW_HEARTBEAT_VERSION_CUTOFF) { if (product_id == ION_DEVICE_ID_TI_EDGEPORT_416 || product_id == ION_DEVICE_ID_TI_EDGEPORT_416B) { edge_serial->use_heartbeat = true; } } edge_heartbeat_schedule(edge_serial); return 0; } static void edge_disconnect(struct usb_serial *serial) { struct edgeport_serial *edge_serial = usb_get_serial_data(serial); cancel_delayed_work_sync(&edge_serial->heartbeat_work); } static void edge_release(struct usb_serial *serial) { struct edgeport_serial *edge_serial = usb_get_serial_data(serial); cancel_delayed_work_sync(&edge_serial->heartbeat_work); kfree(edge_serial); } static int edge_port_probe(struct usb_serial_port *port) { struct edgeport_port *edge_port; int ret; edge_port = kzalloc(sizeof(*edge_port), GFP_KERNEL); if (!edge_port) return -ENOMEM; spin_lock_init(&edge_port->ep_lock); edge_port->port = port; edge_port->edge_serial = usb_get_serial_data(port->serial); edge_port->bUartMode = default_uart_mode; switch (port->port_number) { case 0: edge_port->uart_base = UMPMEM_BASE_UART1; edge_port->dma_address = UMPD_OEDB1_ADDRESS; break; case 1: edge_port->uart_base = UMPMEM_BASE_UART2; edge_port->dma_address = UMPD_OEDB2_ADDRESS; break; default: dev_err(&port->dev, "unknown port number\n"); ret = -ENODEV; goto err; } dev_dbg(&port->dev, "%s - port_number = %d, uart_base = %04x, dma_address = %04x\n", __func__, port->port_number, edge_port->uart_base, edge_port->dma_address); usb_set_serial_port_data(port, edge_port); ret = edge_create_sysfs_attrs(port); if (ret) goto err; port->port.closing_wait = msecs_to_jiffies(closing_wait * 10); port->port.drain_delay = 1; return 0; err: kfree(edge_port); return ret; } static int edge_port_remove(struct usb_serial_port *port) { struct edgeport_port *edge_port; edge_port = usb_get_serial_port_data(port); edge_remove_sysfs_attrs(port); kfree(edge_port); return 0; } /* Sysfs Attributes */ static ssize_t uart_mode_show(struct device *dev, struct device_attribute *attr, char *buf) { struct usb_serial_port *port = to_usb_serial_port(dev); struct edgeport_port *edge_port = usb_get_serial_port_data(port); return sprintf(buf, "%d\n", edge_port->bUartMode); } static ssize_t uart_mode_store(struct device *dev, struct device_attribute *attr, const char *valbuf, size_t count) { struct usb_serial_port *port = to_usb_serial_port(dev); struct edgeport_port *edge_port = usb_get_serial_port_data(port); unsigned int v = simple_strtoul(valbuf, NULL, 0); dev_dbg(dev, "%s: setting uart_mode = %d\n", __func__, v); if (v < 256) edge_port->bUartMode = v; else dev_err(dev, "%s - uart_mode %d is invalid\n", __func__, v); return count; } static DEVICE_ATTR_RW(uart_mode); static int edge_create_sysfs_attrs(struct usb_serial_port *port) { return device_create_file(&port->dev, &dev_attr_uart_mode); } static int edge_remove_sysfs_attrs(struct usb_serial_port *port) { device_remove_file(&port->dev, &dev_attr_uart_mode); return 0; } #ifdef CONFIG_PM static int edge_suspend(struct usb_serial *serial, pm_message_t message) { struct edgeport_serial *edge_serial = usb_get_serial_data(serial); cancel_delayed_work_sync(&edge_serial->heartbeat_work); return 0; } static int edge_resume(struct usb_serial *serial) { struct edgeport_serial *edge_serial = usb_get_serial_data(serial); edge_heartbeat_schedule(edge_serial); return 0; } #endif static struct usb_serial_driver edgeport_1port_device = { .driver = { .owner = THIS_MODULE, .name = "edgeport_ti_1", }, .description = "Edgeport TI 1 port adapter", .id_table = edgeport_1port_id_table, .num_ports = 1, .open = edge_open, .close = edge_close, .throttle = edge_throttle, .unthrottle = edge_unthrottle, .attach = edge_startup, .disconnect = edge_disconnect, .release = edge_release, .port_probe = edge_port_probe, .port_remove = edge_port_remove, .ioctl = edge_ioctl, .set_termios = edge_set_termios, .tiocmget = edge_tiocmget, .tiocmset = edge_tiocmset, .tiocmiwait = usb_serial_generic_tiocmiwait, .get_icount = usb_serial_generic_get_icount, .write = edge_write, .write_room = edge_write_room, .chars_in_buffer = edge_chars_in_buffer, .tx_empty = edge_tx_empty, .break_ctl = edge_break, .read_int_callback = edge_interrupt_callback, .read_bulk_callback = edge_bulk_in_callback, .write_bulk_callback = edge_bulk_out_callback, #ifdef CONFIG_PM .suspend = edge_suspend, .resume = edge_resume, #endif }; static struct usb_serial_driver edgeport_2port_device = { .driver = { .owner = THIS_MODULE, .name = "edgeport_ti_2", }, .description = "Edgeport TI 2 port adapter", .id_table = edgeport_2port_id_table, .num_ports = 2, .open = edge_open, .close = edge_close, .throttle = edge_throttle, .unthrottle = edge_unthrottle, .attach = edge_startup, .disconnect = edge_disconnect, .release = edge_release, .port_probe = edge_port_probe, .port_remove = edge_port_remove, .ioctl = edge_ioctl, .set_termios = edge_set_termios, .tiocmget = edge_tiocmget, .tiocmset = edge_tiocmset, .tiocmiwait = usb_serial_generic_tiocmiwait, .get_icount = usb_serial_generic_get_icount, .write = edge_write, .write_room = edge_write_room, .chars_in_buffer = edge_chars_in_buffer, .tx_empty = edge_tx_empty, .break_ctl = edge_break, .read_int_callback = edge_interrupt_callback, .read_bulk_callback = edge_bulk_in_callback, .write_bulk_callback = edge_bulk_out_callback, #ifdef CONFIG_PM .suspend = edge_suspend, .resume = edge_resume, #endif }; static struct usb_serial_driver * const serial_drivers[] = { &edgeport_1port_device, &edgeport_2port_device, NULL }; module_usb_serial_driver(serial_drivers, id_table_combined); MODULE_AUTHOR(DRIVER_AUTHOR); MODULE_DESCRIPTION(DRIVER_DESC); MODULE_LICENSE("GPL"); MODULE_FIRMWARE("edgeport/down3.bin"); module_param(closing_wait, int, S_IRUGO | S_IWUSR); MODULE_PARM_DESC(closing_wait, "Maximum wait for data to drain, in .01 secs"); module_param(ignore_cpu_rev, bool, S_IRUGO | S_IWUSR); MODULE_PARM_DESC(ignore_cpu_rev, "Ignore the cpu revision when connecting to a device"); module_param(default_uart_mode, int, S_IRUGO | S_IWUSR); MODULE_PARM_DESC(default_uart_mode, "Default uart_mode, 0=RS232, ...");