menu "Passive cards" config ISDN_DRV_HISAX tristate "HiSax SiemensChipSet driver support" select CRC_CCITT ---help--- This is a driver supporting the Siemens chipset on various ISDN-cards (like AVM A1, Elsa ISDN cards, Teles S0-16.0, Teles S0-16.3, Teles S0-8, Teles/Creatix PnP, ITK micro ix1 and many compatibles). HiSax is just the name of this driver, not the name of any hardware. If you have a card with such a chipset, you should say Y here and also to the configuration option of the driver for your particular card, below. if ISDN_DRV_HISAX!=n comment "D-channel protocol features" config HISAX_EURO bool "HiSax Support for EURO/DSS1" help Say Y or N according to the D-channel protocol which your local telephone service company provides. The call control protocol E-DSS1 is used in most European countries. If unsure, say Y. config DE_AOC bool "Support for german chargeinfo" depends on HISAX_EURO help If you want that the HiSax hardware driver sends messages to the upper level of the isdn code on each AOCD (Advice Of Charge, During the call -- transmission of the fee information during a call) and on each AOCE (Advice Of Charge, at the End of the call -- transmission of fee information at the end of the call), say Y here. This works only in Germany. config HISAX_NO_SENDCOMPLETE bool "Disable sending complete" depends on HISAX_EURO help If you have trouble with some ugly exchanges or you live in Australia select this option. config HISAX_NO_LLC bool "Disable sending low layer compatibility" depends on HISAX_EURO help If you have trouble with some ugly exchanges try to select this option. config HISAX_NO_KEYPAD bool "Disable keypad protocol option" depends on HISAX_EURO help If you like to send special dial strings including * or # without using the keypad protocol, select this option. config HISAX_1TR6 bool "HiSax Support for german 1TR6" help Say Y or N according to the D-channel protocol which your local telephone service company provides. 1TR6 is an old call control protocol which was used in Germany before E-DSS1 was established. Nowadays, all new lines in Germany use E-DSS1. config HISAX_NI1 bool "HiSax Support for US NI1" help Enable this if you like to use ISDN in US on a NI1 basic rate interface. config HISAX_MAX_CARDS int "Maximum number of cards supported by HiSax" default "8" help This option allows you to specify the maximum number of cards which the HiSax driver will be able to handle. comment "HiSax supported cards" config HISAX_16_0 bool "Teles 16.0/8.0" depends on ISA help This enables HiSax support for the Teles ISDN-cards S0-16.0, S0-8 and many compatibles. See on how to configure it using the different cards, a different D-channel protocol, or non-standard IRQ/port/shmem settings. config HISAX_16_3 bool "Teles 16.3 or PNP or PCMCIA" help This enables HiSax support for the Teles ISDN-cards S0-16.3 the Teles/Creatix PnP and the Teles PCMCIA. See on how to configure it using the different cards, a different D-channel protocol, or non-standard IRQ/port settings. config HISAX_TELESPCI bool "Teles PCI" depends on PCI && PCI_LEGACY && (BROKEN || !(SPARC || PPC || PARISC || M68K || (MIPS && !CPU_LITTLE_ENDIAN) || FRV)) help This enables HiSax support for the Teles PCI. See on how to configure it. config HISAX_S0BOX bool "Teles S0Box" help This enables HiSax support for the Teles/Creatix parallel port S0BOX. See on how to configure it. config HISAX_AVM_A1 bool "AVM A1 (Fritz)" depends on ISA help This enables HiSax support for the AVM A1 (aka "Fritz"). See on how to configure it using the different cards, a different D-channel protocol, or non-standard IRQ/port settings. config HISAX_FRITZPCI bool "AVM PnP/PCI (Fritz!PnP/PCI)" depends on BROKEN || !PPC64 help This enables HiSax support for the AVM "Fritz!PnP" and "Fritz!PCI". See on how to configure it. config HISAX_AVM_A1_PCMCIA bool "AVM A1 PCMCIA (Fritz)" help This enables HiSax support for the AVM A1 "Fritz!PCMCIA"). See on how to configure it. config HISAX_ELSA bool "Elsa cards" help This enables HiSax support for the Elsa Mircolink ISA cards, for the Elsa Quickstep series cards and Elsa PCMCIA. See on how to configure it using the different cards, a different D-channel protocol, or non-standard IRQ/port settings. config HISAX_IX1MICROR2 bool "ITK ix1-micro Revision 2" depends on ISA help This enables HiSax support for the ITK ix1-micro Revision 2 card. See on how to configure it using the different cards, a different D-channel protocol, or non-standard IRQ/port settings. config HISAX_DIEHLDIVA bool "Eicon.Diehl Diva cards" help This enables HiSax support for the Eicon.Diehl Diva none PRO versions passive ISDN cards. See on how to configure it using the different cards, a different D-channel protocol, or non-standard IRQ/port settings. config HISAX_ASUSCOM bool "ASUSCOM ISA cards" depends on ISA help This enables HiSax support for the AsusCom and their OEM versions passive ISDN ISA cards. See on how to configure it using the different cards, a different D-channel protocol, or non-standard IRQ/port settings. config HISAX_TELEINT bool "TELEINT cards" depends on ISA help This enables HiSax support for the TELEINT SA1 semiactiv ISDN card. See on how to configure it using the different cards, a different D-channel protocol, or non-standard IRQ/port settings. config HISAX_HFCS bool "HFC-S based cards" depends on ISA help This enables HiSax support for the HFC-S 2BDS0 based cards, like teles 16.3c. See on how to configure it using the different cards, a different D-channel protocol, or non-standard IRQ/port settings. config HISAX_SEDLBAUER bool "Sedlbauer cards" help This enables HiSax support for the Sedlbauer passive ISDN cards. See on how to configure it using the different cards, a different D-channel protocol, or non-standard IRQ/port settings. config HISAX_SPORTSTER bool "USR Sportster internal TA" depends on ISA help This enables HiSax support for the USR Sportster internal TA card. See on how to configure it using a different D-channel protocol, or non-standard IRQ/port settings. config HISAX_MIC bool "MIC card" depends on ISA help This enables HiSax support for the ITH MIC card. See on how to configure it using a different D-channel protocol, or non-standard IRQ/port settings. config HISAX_NETJET bool "NETjet card" depends on PCI && PCI_LEGACY && (BROKEN || !(SPARC || PPC || PARISC || M68K || (MIPS && !CPU_LITTLE_ENDIAN) || FRV)) help This enables HiSax support for the NetJet from Traverse Technologies. See on how to configure it using a different D-channel protocol, or non-standard IRQ/port settings. config HISAX_NETJET_U bool "NETspider U card" depends on PCI && PCI_LEGACY && (BROKEN || !(SPARC || PPC || PARISC || M68K || (MIPS && !CPU_LITTLE_ENDIAN) || FRV)) help This enables HiSax support for the Netspider U interface ISDN card from Traverse Technologies. See on how to configure it using a different D-channel protocol, or non-standard IRQ/port settings. config HISAX_NICCY bool "Niccy PnP/PCI card" help This enables HiSax support for the Dr. Neuhaus Niccy PnP or PCI. See on how to configure it using a different D-channel protocol, or non-standard IRQ/port settings. config HISAX_ISURF bool "Siemens I-Surf card" depends on ISA help This enables HiSax support for the Siemens I-Talk/I-Surf card with ISAR chip. See on how to configure it using a different D-channel protocol, or non-standard IRQ/port settings. config HISAX_HSTSAPHIR bool "HST Saphir card" depends on ISA help This enables HiSax support for the HST Saphir card. See on how to configure it using a different D-channel protocol, or non-standard IRQ/port settings. config HISAX_BKM_A4T bool "Telekom A4T card" depends on PCI && PCI_LEGACY help This enables HiSax support for the Telekom A4T card. See on how to configure it using a different D-channel protocol, or non-standard IRQ/port settings. config HISAX_SCT_QUADRO bool "Scitel Quadro card" depends on PCI && PCI_LEGACY help This enables HiSax support for the Scitel Quadro card. See on how to configure it using a different D-channel protocol, or non-standard IRQ/port settings. config HISAX_GAZEL bool "Gazel cards" help This enables HiSax support for the Gazel cards. See on how to configure it using a different D-channel protocol, or non-standard IRQ/port settings. config HISAX_HFC_PCI bool "HFC PCI-Bus cards" depends on PCI && PCI_LEGACY && (BROKEN || !(SPARC || PPC || PARISC || M68K || (MIPS && !CPU_LITTLE_ENDIAN) || FRV)) help This enables HiSax support for the HFC-S PCI 2BDS0 based cards. For more information see under . config HISAX_W6692 bool "Winbond W6692 based cards" depends on PCI && PCI_LEGACY help This enables HiSax support for Winbond W6692 based PCI ISDN cards. See on how to configure it using a different D-channel protocol, or non-standard IRQ/port settings. config HISAX_HFC_SX bool "HFC-S+, HFC-SP, HFC-PCMCIA cards" help This enables HiSax support for the HFC-S+, HFC-SP and HFC-PCMCIA cards. This code is not finished yet. config HISAX_ENTERNOW_PCI bool "Formula-n enter:now PCI card" depends on HISAX_NETJET && PCI && PCI_LEGACY && (BROKEN || !(SPARC || PPC || PARISC || M68K || (MIPS && !CPU_LITTLE_ENDIAN) || FRV)) help This enables HiSax support for the Formula-n enter:now PCI ISDN card. endif if ISDN_DRV_HISAX config HISAX_DEBUG bool "HiSax debugging" help This enables debugging code in the new-style HiSax drivers, i.e. the ST5481 USB driver currently. If in doubt, say yes. comment "HiSax PCMCIA card service modules" config HISAX_SEDLBAUER_CS tristate "Sedlbauer PCMCIA cards" depends on PCMCIA && HISAX_SEDLBAUER help This enables the PCMCIA client driver for the Sedlbauer Speed Star and Speed Star II cards. config HISAX_ELSA_CS tristate "ELSA PCMCIA MicroLink cards" depends on PCMCIA && HISAX_ELSA help This enables the PCMCIA client driver for the Elsa PCMCIA MicroLink card. config HISAX_AVM_A1_CS tristate "AVM A1 PCMCIA cards" depends on PCMCIA && ISDN_DRV_HISAX help This enables the PCMCIA client driver for the AVM A1 / Fritz!Card PCMCIA cards. config HISAX_TELES_CS tristate "TELES PCMCIA cards" depends on PCMCIA && HISAX_16_3 help This enables the PCMCIA client driver for the Teles PCMCIA cards. comment "HiSax sub driver modules" config HISAX_ST5481 tristate "ST5481 USB ISDN modem (EXPERIMENTAL)" depends on USB && EXPERIMENTAL select ISDN_HDLC select CRC_CCITT select BITREVERSE help This enables the driver for ST5481 based USB ISDN adapters, e.g. the BeWan Gazel 128 USB config HISAX_HFCUSB tristate "HFC USB based ISDN modems (EXPERIMENTAL)" depends on USB && EXPERIMENTAL help This enables the driver for HFC USB based ISDN modems. config HISAX_HFC4S8S tristate "HFC-4S/8S based ISDN cards (EXPERIMENTAL)" depends on EXPERIMENTAL help This enables the driver for HFC-4S/8S based ISDN cards. config HISAX_FRITZ_PCIPNP tristate "AVM Fritz!Card PCI/PCIv2/PnP support (EXPERIMENTAL)" depends on PCI && PCI_LEGACY && EXPERIMENTAL help This enables the driver for the AVM Fritz!Card PCI, Fritz!Card PCI v2 and Fritz!Card PnP. (the latter also needs you to select "ISA Plug and Play support" from the menu "Plug and Play configuration") config HISAX_AVM_A1_PCMCIA bool depends on HISAX_AVM_A1_CS default y endif endmenu