/* * USB FTDI SIO driver * * Copyright (C) 1999 - 2001 * Greg Kroah-Hartman (greg@kroah.com) * Bill Ryder (bryder@sgi.com) * Copyright (C) 2002 * Kuba Ober (kuba@mareimbrium.org) * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation; either version 2 of the License, or * (at your option) any later version. * * See Documentation/usb/usb-serial.txt for more information on using this * driver * * See http://ftdi-usb-sio.sourceforge.net for upto date testing info * and extra documentation * * Change entries from 2004 and earlier can be found in versions of this * file in kernel versions prior to the 2.6.24 release. * */ /* Bill Ryder - bryder@sgi.com - wrote the FTDI_SIO implementation */ /* Thanx to FTDI for so kindly providing details of the protocol required */ /* to talk to the device */ /* Thanx to gkh and the rest of the usb dev group for all code I have assimilated :-) */ #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include "ftdi_sio.h" #include "ftdi_sio_ids.h" /* * Version Information */ #define DRIVER_VERSION "v1.5.0" #define DRIVER_AUTHOR "Greg Kroah-Hartman , Bill Ryder , Kuba Ober , Andreas Mohr" #define DRIVER_DESC "USB FTDI Serial Converters Driver" static int debug; static __u16 vendor = FTDI_VID; static __u16 product; struct ftdi_private { struct kref kref; ftdi_chip_type_t chip_type; /* type of device, either SIO or FT8U232AM */ int baud_base; /* baud base clock for divisor setting */ int custom_divisor; /* custom_divisor kludge, this is for baud_base (different from what goes to the chip!) */ __u16 last_set_data_urb_value ; /* the last data state set - needed for doing * a break */ int write_offset; /* This is the offset in the usb data block to * write the serial data - it varies between * devices */ int flags; /* some ASYNC_xxxx flags are supported */ unsigned long last_dtr_rts; /* saved modem control outputs */ wait_queue_head_t delta_msr_wait; /* Used for TIOCMIWAIT */ char prev_status, diff_status; /* Used for TIOCMIWAIT */ struct usb_serial_port *port; __u16 interface; /* FT2232C, FT2232H or FT4232H port interface (0 for FT232/245) */ speed_t force_baud; /* if non-zero, force the baud rate to this value */ int force_rtscts; /* if non-zero, force RTS-CTS to always be enabled */ unsigned int latency; /* latency setting in use */ spinlock_t tx_lock; /* spinlock for transmit state */ unsigned long tx_bytes; unsigned long tx_outstanding_bytes; unsigned long tx_outstanding_urbs; unsigned short max_packet_size; }; /* struct ftdi_sio_quirk is used by devices requiring special attention. */ struct ftdi_sio_quirk { int (*probe)(struct usb_serial *); /* Special settings for probed ports. */ void (*port_probe)(struct ftdi_private *); }; static int ftdi_jtag_probe(struct usb_serial *serial); static int ftdi_mtxorb_hack_setup(struct usb_serial *serial); static int ftdi_NDI_device_setup(struct usb_serial *serial); static int ftdi_stmclite_probe(struct usb_serial *serial); static int ftdi_8u2232c_probe(struct usb_serial *serial); static void ftdi_USB_UIRT_setup(struct ftdi_private *priv); static void ftdi_HE_TIRA1_setup(struct ftdi_private *priv); static struct ftdi_sio_quirk ftdi_jtag_quirk = { .probe = ftdi_jtag_probe, }; static struct ftdi_sio_quirk ftdi_mtxorb_hack_quirk = { .probe = ftdi_mtxorb_hack_setup, }; static struct ftdi_sio_quirk ftdi_NDI_device_quirk = { .probe = ftdi_NDI_device_setup, }; static struct ftdi_sio_quirk ftdi_USB_UIRT_quirk = { .port_probe = ftdi_USB_UIRT_setup, }; static struct ftdi_sio_quirk ftdi_HE_TIRA1_quirk = { .port_probe = ftdi_HE_TIRA1_setup, }; static struct ftdi_sio_quirk ftdi_stmclite_quirk = { .probe = ftdi_stmclite_probe, }; static struct ftdi_sio_quirk ftdi_8u2232c_quirk = { .probe = ftdi_8u2232c_probe, }; /* * The 8U232AM has the same API as the sio except for: * - it can support MUCH higher baudrates; up to: * o 921600 for RS232 and 2000000 for RS422/485 at 48MHz * o 230400 at 12MHz * so .. 8U232AM's baudrate setting codes are different * - it has a two byte status code. * - it returns characters every 16ms (the FTDI does it every 40ms) * * the bcdDevice value is used to differentiate FT232BM and FT245BM from * the earlier FT8U232AM and FT8U232BM. For now, include all known VID/PID * combinations in both tables. * FIXME: perhaps bcdDevice can also identify 12MHz FT8U232AM devices, * but I don't know if those ever went into mass production. [Ian Abbott] */ /* * Device ID not listed? Test via module params product/vendor or * /sys/bus/usb/ftdi_sio/new_id, then send patch/report! */ static struct usb_device_id id_table_combined [] = { { USB_DEVICE(FTDI_VID, FTDI_ZEITCONTROL_TAGTRACE_MIFARE_PID) }, { USB_DEVICE(FTDI_VID, FTDI_CTI_MINI_PID) }, { USB_DEVICE(FTDI_VID, FTDI_CTI_NANO_PID) }, { USB_DEVICE(FTDI_VID, FTDI_AMC232_PID) }, { USB_DEVICE(FTDI_VID, FTDI_CANUSB_PID) }, { USB_DEVICE(FTDI_VID, FTDI_CANDAPTER_PID) }, { USB_DEVICE(FTDI_VID, FTDI_NXTCAM_PID) }, { USB_DEVICE(FTDI_VID, FTDI_SCS_DEVICE_0_PID) }, { USB_DEVICE(FTDI_VID, FTDI_SCS_DEVICE_1_PID) }, { USB_DEVICE(FTDI_VID, FTDI_SCS_DEVICE_2_PID) }, { USB_DEVICE(FTDI_VID, FTDI_SCS_DEVICE_3_PID) }, { USB_DEVICE(FTDI_VID, FTDI_SCS_DEVICE_4_PID) }, { USB_DEVICE(FTDI_VID, FTDI_SCS_DEVICE_5_PID) }, { USB_DEVICE(FTDI_VID, FTDI_SCS_DEVICE_6_PID) }, { USB_DEVICE(FTDI_VID, FTDI_SCS_DEVICE_7_PID) }, { USB_DEVICE(FTDI_VID, FTDI_USINT_CAT_PID) }, { USB_DEVICE(FTDI_VID, FTDI_USINT_WKEY_PID) }, { USB_DEVICE(FTDI_VID, FTDI_USINT_RS232_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ACTZWAVE_PID) }, { USB_DEVICE(FTDI_VID, FTDI_IRTRANS_PID) }, { USB_DEVICE(FTDI_VID, FTDI_IPLUS_PID) }, { USB_DEVICE(FTDI_VID, FTDI_IPLUS2_PID) }, { USB_DEVICE(FTDI_VID, FTDI_DMX4ALL) }, { USB_DEVICE(FTDI_VID, FTDI_SIO_PID) }, { USB_DEVICE(FTDI_VID, FTDI_8U232AM_PID) }, { USB_DEVICE(FTDI_VID, FTDI_8U232AM_ALT_PID) }, { USB_DEVICE(FTDI_VID, FTDI_232RL_PID) }, { USB_DEVICE(FTDI_VID, FTDI_8U2232C_PID) , .driver_info = (kernel_ulong_t)&ftdi_8u2232c_quirk }, { USB_DEVICE(FTDI_VID, FTDI_4232H_PID) }, { USB_DEVICE(FTDI_VID, FTDI_MICRO_CHAMELEON_PID) }, { USB_DEVICE(FTDI_VID, FTDI_RELAIS_PID) }, { USB_DEVICE(FTDI_VID, FTDI_OPENDCC_PID) }, { USB_DEVICE(FTDI_VID, FTDI_OPENDCC_SNIFFER_PID) }, { USB_DEVICE(FTDI_VID, FTDI_OPENDCC_THROTTLE_PID) }, { USB_DEVICE(FTDI_VID, FTDI_OPENDCC_GATEWAY_PID) }, { USB_DEVICE(FTDI_VID, FTDI_OPENDCC_GBM_PID) }, { USB_DEVICE(INTERBIOMETRICS_VID, INTERBIOMETRICS_IOBOARD_PID) }, { USB_DEVICE(INTERBIOMETRICS_VID, INTERBIOMETRICS_MINI_IOBOARD_PID) }, { USB_DEVICE(FTDI_VID, FTDI_SPROG_II) }, { USB_DEVICE(FTDI_VID, FTDI_LENZ_LIUSB_PID) }, { USB_DEVICE(FTDI_VID, FTDI_XF_632_PID) }, { USB_DEVICE(FTDI_VID, FTDI_XF_634_PID) }, { USB_DEVICE(FTDI_VID, FTDI_XF_547_PID) }, { USB_DEVICE(FTDI_VID, FTDI_XF_633_PID) }, { USB_DEVICE(FTDI_VID, FTDI_XF_631_PID) }, { USB_DEVICE(FTDI_VID, FTDI_XF_635_PID) }, { USB_DEVICE(FTDI_VID, FTDI_XF_640_PID) }, { USB_DEVICE(FTDI_VID, FTDI_XF_642_PID) }, { USB_DEVICE(FTDI_VID, FTDI_DSS20_PID) }, { USB_DEVICE(FTDI_VID, FTDI_URBAN_0_PID) }, { USB_DEVICE(FTDI_VID, FTDI_URBAN_1_PID) }, { USB_DEVICE(FTDI_NF_RIC_VID, FTDI_NF_RIC_PID) }, { USB_DEVICE(FTDI_VID, FTDI_VNHCPCUSB_D_PID) }, { USB_DEVICE(FTDI_VID, FTDI_MTXORB_0_PID) }, { USB_DEVICE(FTDI_VID, FTDI_MTXORB_1_PID) }, { USB_DEVICE(FTDI_VID, FTDI_MTXORB_2_PID) }, { USB_DEVICE(FTDI_VID, FTDI_MTXORB_3_PID) }, { USB_DEVICE(FTDI_VID, FTDI_MTXORB_4_PID) }, { USB_DEVICE(FTDI_VID, FTDI_MTXORB_5_PID) }, { USB_DEVICE(FTDI_VID, FTDI_MTXORB_6_PID) }, { USB_DEVICE(FTDI_VID, FTDI_R2000KU_TRUE_RNG) }, { USB_DEVICE(FTDI_VID, FTDI_VARDAAN_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0100_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0101_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0102_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0103_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0104_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0105_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0106_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0107_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0108_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0109_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_010A_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_010B_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_010C_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_010D_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_010E_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_010F_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0110_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0111_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0112_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0113_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0114_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0115_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0116_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0117_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0118_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0119_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_011A_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_011B_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_011C_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_011D_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_011E_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_011F_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0120_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0121_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0122_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0123_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0124_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0125_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0126_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0127_PID), .driver_info = (kernel_ulong_t)&ftdi_mtxorb_hack_quirk }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0128_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0129_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_012A_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_012B_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_012C_PID), .driver_info = (kernel_ulong_t)&ftdi_mtxorb_hack_quirk }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_012D_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_012E_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_012F_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0130_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0131_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0132_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0133_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0134_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0135_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0136_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0137_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0138_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0139_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_013A_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_013B_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_013C_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_013D_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_013E_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_013F_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0140_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0141_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0142_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0143_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0144_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0145_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0146_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0147_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0148_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0149_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_014A_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_014B_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_014C_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_014D_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_014E_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_014F_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0150_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0151_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0152_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0153_PID), .driver_info = (kernel_ulong_t)&ftdi_mtxorb_hack_quirk }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0154_PID), .driver_info = (kernel_ulong_t)&ftdi_mtxorb_hack_quirk }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0155_PID), .driver_info = (kernel_ulong_t)&ftdi_mtxorb_hack_quirk }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0156_PID), .driver_info = (kernel_ulong_t)&ftdi_mtxorb_hack_quirk }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0157_PID), .driver_info = (kernel_ulong_t)&ftdi_mtxorb_hack_quirk }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0158_PID), .driver_info = (kernel_ulong_t)&ftdi_mtxorb_hack_quirk }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0159_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_015A_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_015B_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_015C_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_015D_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_015E_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_015F_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0160_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0161_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0162_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0163_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0164_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0165_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0166_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0167_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0168_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0169_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_016A_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_016B_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_016C_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_016D_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_016E_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_016F_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0170_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0171_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0172_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0173_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0174_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0175_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0176_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0177_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0178_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0179_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_017A_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_017B_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_017C_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_017D_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_017E_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_017F_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0180_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0181_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0182_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0183_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0184_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0185_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0186_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0187_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0188_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0189_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_018A_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_018B_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_018C_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_018D_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_018E_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_018F_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0190_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0191_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0192_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0193_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0194_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0195_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0196_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0197_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0198_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0199_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_019A_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_019B_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_019C_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_019D_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_019E_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_019F_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01A0_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01A1_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01A2_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01A3_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01A4_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01A5_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01A6_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01A7_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01A8_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01A9_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01AA_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01AB_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01AC_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01AD_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01AE_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01AF_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01B0_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01B1_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01B2_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01B3_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01B4_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01B5_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01B6_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01B7_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01B8_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01B9_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01BA_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01BB_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01BC_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01BD_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01BE_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01BF_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01C0_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01C1_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01C2_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01C3_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01C4_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01C5_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01C6_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01C7_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01C8_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01C9_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01CA_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01CB_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01CC_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01CD_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01CE_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01CF_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01D0_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01D1_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01D2_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01D3_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01D4_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01D5_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01D6_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01D7_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01D8_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01D9_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01DA_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01DB_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01DC_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01DD_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01DE_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01DF_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01E0_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01E1_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01E2_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01E3_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01E4_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01E5_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01E6_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01E7_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01E8_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01E9_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01EA_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01EB_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01EC_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01ED_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01EE_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01EF_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01F0_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01F1_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01F2_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01F3_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01F4_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01F5_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01F6_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01F7_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01F8_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01F9_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01FA_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01FB_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01FC_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01FD_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01FE_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_01FF_PID) }, { USB_DEVICE(FTDI_VID, FTDI_PERLE_ULTRAPORT_PID) }, { USB_DEVICE(FTDI_VID, FTDI_PIEGROUP_PID) }, { USB_DEVICE(FTDI_VID, FTDI_TNC_X_PID) }, { USB_DEVICE(FTDI_VID, FTDI_USBX_707_PID) }, { USB_DEVICE(SEALEVEL_VID, SEALEVEL_2101_PID) }, { USB_DEVICE(SEALEVEL_VID, SEALEVEL_2102_PID) }, { USB_DEVICE(SEALEVEL_VID, SEALEVEL_2103_PID) }, { USB_DEVICE(SEALEVEL_VID, SEALEVEL_2104_PID) }, { USB_DEVICE(SEALEVEL_VID, SEALEVEL_2106_PID) }, { USB_DEVICE(SEALEVEL_VID, SEALEVEL_2201_1_PID) }, { USB_DEVICE(SEALEVEL_VID, SEALEVEL_2201_2_PID) }, { USB_DEVICE(SEALEVEL_VID, SEALEVEL_2202_1_PID) }, { USB_DEVICE(SEALEVEL_VID, SEALEVEL_2202_2_PID) }, { USB_DEVICE(SEALEVEL_VID, SEALEVEL_2203_1_PID) }, { USB_DEVICE(SEALEVEL_VID, SEALEVEL_2203_2_PID) }, { USB_DEVICE(SEALEVEL_VID, SEALEVEL_2401_1_PID) }, { USB_DEVICE(SEALEVEL_VID, SEALEVEL_2401_2_PID) }, { USB_DEVICE(SEALEVEL_VID, SEALEVEL_2401_3_PID) }, { USB_DEVICE(SEALEVEL_VID, SEALEVEL_2401_4_PID) }, { USB_DEVICE(SEALEVEL_VID, SEALEVEL_2402_1_PID) }, { USB_DEVICE(SEALEVEL_VID, SEALEVEL_2402_2_PID) }, { USB_DEVICE(SEALEVEL_VID, SEALEVEL_2402_3_PID) }, { USB_DEVICE(SEALEVEL_VID, SEALEVEL_2402_4_PID) }, { USB_DEVICE(SEALEVEL_VID, SEALEVEL_2403_1_PID) }, { USB_DEVICE(SEALEVEL_VID, SEALEVEL_2403_2_PID) }, { USB_DEVICE(SEALEVEL_VID, SEALEVEL_2403_3_PID) }, { USB_DEVICE(SEALEVEL_VID, SEALEVEL_2403_4_PID) }, { USB_DEVICE(SEALEVEL_VID, SEALEVEL_2801_1_PID) }, { USB_DEVICE(SEALEVEL_VID, SEALEVEL_2801_2_PID) }, { USB_DEVICE(SEALEVEL_VID, SEALEVEL_2801_3_PID) }, { USB_DEVICE(SEALEVEL_VID, SEALEVEL_2801_4_PID) }, { USB_DEVICE(SEALEVEL_VID, SEALEVEL_2801_5_PID) }, { USB_DEVICE(SEALEVEL_VID, SEALEVEL_2801_6_PID) }, { USB_DEVICE(SEALEVEL_VID, SEALEVEL_2801_7_PID) }, { USB_DEVICE(SEALEVEL_VID, SEALEVEL_2801_8_PID) }, { USB_DEVICE(SEALEVEL_VID, SEALEVEL_2802_1_PID) }, { USB_DEVICE(SEALEVEL_VID, SEALEVEL_2802_2_PID) }, { USB_DEVICE(SEALEVEL_VID, SEALEVEL_2802_3_PID) }, { USB_DEVICE(SEALEVEL_VID, SEALEVEL_2802_4_PID) }, { USB_DEVICE(SEALEVEL_VID, SEALEVEL_2802_5_PID) }, { USB_DEVICE(SEALEVEL_VID, SEALEVEL_2802_6_PID) }, { USB_DEVICE(SEALEVEL_VID, SEALEVEL_2802_7_PID) }, { USB_DEVICE(SEALEVEL_VID, SEALEVEL_2802_8_PID) }, { USB_DEVICE(SEALEVEL_VID, SEALEVEL_2803_1_PID) }, { USB_DEVICE(SEALEVEL_VID, SEALEVEL_2803_2_PID) }, { USB_DEVICE(SEALEVEL_VID, SEALEVEL_2803_3_PID) }, { USB_DEVICE(SEALEVEL_VID, SEALEVEL_2803_4_PID) }, { USB_DEVICE(SEALEVEL_VID, SEALEVEL_2803_5_PID) }, { USB_DEVICE(SEALEVEL_VID, SEALEVEL_2803_6_PID) }, { USB_DEVICE(SEALEVEL_VID, SEALEVEL_2803_7_PID) }, { USB_DEVICE(SEALEVEL_VID, SEALEVEL_2803_8_PID) }, { USB_DEVICE(IDTECH_VID, IDTECH_IDT1221U_PID) }, { USB_DEVICE(OCT_VID, OCT_US101_PID) }, { USB_DEVICE(OCT_VID, OCT_DK201_PID) }, { USB_DEVICE(FTDI_VID, FTDI_HE_TIRA1_PID), .driver_info = (kernel_ulong_t)&ftdi_HE_TIRA1_quirk }, { USB_DEVICE(FTDI_VID, FTDI_USB_UIRT_PID), .driver_info = (kernel_ulong_t)&ftdi_USB_UIRT_quirk }, { USB_DEVICE(FTDI_VID, PROTEGO_SPECIAL_1) }, { USB_DEVICE(FTDI_VID, PROTEGO_R2X0) }, { USB_DEVICE(FTDI_VID, PROTEGO_SPECIAL_3) }, { USB_DEVICE(FTDI_VID, PROTEGO_SPECIAL_4) }, { USB_DEVICE(FTDI_VID, FTDI_GUDEADS_E808_PID) }, { USB_DEVICE(FTDI_VID, FTDI_GUDEADS_E809_PID) }, { USB_DEVICE(FTDI_VID, FTDI_GUDEADS_E80A_PID) }, { USB_DEVICE(FTDI_VID, FTDI_GUDEADS_E80B_PID) }, { USB_DEVICE(FTDI_VID, FTDI_GUDEADS_E80C_PID) }, { USB_DEVICE(FTDI_VID, FTDI_GUDEADS_E80D_PID) }, { USB_DEVICE(FTDI_VID, FTDI_GUDEADS_E80E_PID) }, { USB_DEVICE(FTDI_VID, FTDI_GUDEADS_E80F_PID) }, { USB_DEVICE(FTDI_VID, FTDI_GUDEADS_E888_PID) }, { USB_DEVICE(FTDI_VID, FTDI_GUDEADS_E889_PID) }, { USB_DEVICE(FTDI_VID, FTDI_GUDEADS_E88A_PID) }, { USB_DEVICE(FTDI_VID, FTDI_GUDEADS_E88B_PID) }, { USB_DEVICE(FTDI_VID, FTDI_GUDEADS_E88C_PID) }, { USB_DEVICE(FTDI_VID, FTDI_GUDEADS_E88D_PID) }, { USB_DEVICE(FTDI_VID, FTDI_GUDEADS_E88E_PID) }, { USB_DEVICE(FTDI_VID, FTDI_GUDEADS_E88F_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ELV_UO100_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ELV_UM100_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ELV_UR100_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ELV_ALC8500_PID) }, { USB_DEVICE(FTDI_VID, FTDI_PYRAMID_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ELV_FHZ1000PC_PID) }, { USB_DEVICE(FTDI_VID, FTDI_IBS_US485_PID) }, { USB_DEVICE(FTDI_VID, FTDI_IBS_PICPRO_PID) }, { USB_DEVICE(FTDI_VID, FTDI_IBS_PCMCIA_PID) }, { USB_DEVICE(FTDI_VID, FTDI_IBS_PK1_PID) }, { USB_DEVICE(FTDI_VID, FTDI_IBS_RS232MON_PID) }, { USB_DEVICE(FTDI_VID, FTDI_IBS_APP70_PID) }, { USB_DEVICE(FTDI_VID, FTDI_IBS_PEDO_PID) }, { USB_DEVICE(FTDI_VID, FTDI_IBS_PROD_PID) }, { USB_DEVICE(FTDI_VID, FTDI_TAVIR_STK500_PID) }, /* * ELV devices: */ { USB_DEVICE(FTDI_VID, FTDI_ELV_USR_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ELV_MSM1_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ELV_KL100_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ELV_WS550_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ELV_EC3000_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ELV_WS888_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ELV_TWS550_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ELV_FEM_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ELV_CLI7000_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ELV_PPS7330_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ELV_TFM100_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ELV_UDF77_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ELV_UIO88_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ELV_UAD8_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ELV_UDA7_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ELV_USI2_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ELV_T1100_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ELV_PCD200_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ELV_ULA200_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ELV_CSI8_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ELV_EM1000DL_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ELV_PCK100_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ELV_RFP500_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ELV_FS20SIG_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ELV_UTP8_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ELV_WS300PC_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ELV_WS444PC_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ELV_FHZ1300PC_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ELV_EM1010PC_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ELV_WS500_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ELV_HS485_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ELV_UMS100_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ELV_TFD128_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ELV_FM3RX_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ELV_WS777_PID) }, { USB_DEVICE(FTDI_VID, LINX_SDMUSBQSS_PID) }, { USB_DEVICE(FTDI_VID, LINX_MASTERDEVEL2_PID) }, { USB_DEVICE(FTDI_VID, LINX_FUTURE_0_PID) }, { USB_DEVICE(FTDI_VID, LINX_FUTURE_1_PID) }, { USB_DEVICE(FTDI_VID, LINX_FUTURE_2_PID) }, { USB_DEVICE(FTDI_VID, FTDI_CCSICDU20_0_PID) }, { USB_DEVICE(FTDI_VID, FTDI_CCSICDU40_1_PID) }, { USB_DEVICE(FTDI_VID, FTDI_CCSMACHX_2_PID) }, { USB_DEVICE(FTDI_VID, FTDI_CCSLOAD_N_GO_3_PID) }, { USB_DEVICE(FTDI_VID, FTDI_CCSICDU64_4_PID) }, { USB_DEVICE(FTDI_VID, FTDI_CCSPRIME8_5_PID) }, { USB_DEVICE(FTDI_VID, INSIDE_ACCESSO) }, { USB_DEVICE(INTREPID_VID, INTREPID_VALUECAN_PID) }, { USB_DEVICE(INTREPID_VID, INTREPID_NEOVI_PID) }, { USB_DEVICE(FALCOM_VID, FALCOM_TWIST_PID) }, { USB_DEVICE(FALCOM_VID, FALCOM_SAMBA_PID) }, { USB_DEVICE(FTDI_VID, FTDI_SUUNTO_SPORTS_PID) }, { USB_DEVICE(FTDI_VID, FTDI_OCEANIC_PID) }, { USB_DEVICE(TTI_VID, TTI_QL355P_PID) }, { USB_DEVICE(FTDI_VID, FTDI_RM_CANVIEW_PID) }, { USB_DEVICE(ACTON_VID, ACTON_SPECTRAPRO_PID) }, { USB_DEVICE(CONTEC_VID, CONTEC_COM1USBH_PID) }, { USB_DEVICE(BANDB_VID, BANDB_USOTL4_PID) }, { USB_DEVICE(BANDB_VID, BANDB_USTL4_PID) }, { USB_DEVICE(BANDB_VID, BANDB_USO9ML2_PID) }, { USB_DEVICE(BANDB_VID, BANDB_USOPTL4_PID) }, { USB_DEVICE(BANDB_VID, BANDB_USPTL4_PID) }, { USB_DEVICE(BANDB_VID, BANDB_USO9ML2DR_2_PID) }, { USB_DEVICE(BANDB_VID, BANDB_USO9ML2DR_PID) }, { USB_DEVICE(BANDB_VID, BANDB_USOPTL4DR2_PID) }, { USB_DEVICE(BANDB_VID, BANDB_USOPTL4DR_PID) }, { USB_DEVICE(BANDB_VID, BANDB_485USB9F_2W_PID) }, { USB_DEVICE(BANDB_VID, BANDB_485USB9F_4W_PID) }, { USB_DEVICE(BANDB_VID, BANDB_232USB9M_PID) }, { USB_DEVICE(BANDB_VID, BANDB_485USBTB_2W_PID) }, { USB_DEVICE(BANDB_VID, BANDB_485USBTB_4W_PID) }, { USB_DEVICE(BANDB_VID, BANDB_TTL5USB9M_PID) }, { USB_DEVICE(BANDB_VID, BANDB_TTL3USB9M_PID) }, { USB_DEVICE(BANDB_VID, BANDB_ZZ_PROG1_USB_PID) }, { USB_DEVICE(FTDI_VID, EVER_ECO_PRO_CDS) }, { USB_DEVICE(FTDI_VID, FTDI_4N_GALAXY_DE_1_PID) }, { USB_DEVICE(FTDI_VID, FTDI_4N_GALAXY_DE_2_PID) }, { USB_DEVICE(FTDI_VID, FTDI_4N_GALAXY_DE_3_PID) }, { USB_DEVICE(FTDI_VID, XSENS_CONVERTER_0_PID) }, { USB_DEVICE(FTDI_VID, XSENS_CONVERTER_1_PID) }, { USB_DEVICE(FTDI_VID, XSENS_CONVERTER_2_PID) }, { USB_DEVICE(FTDI_VID, XSENS_CONVERTER_3_PID) }, { USB_DEVICE(FTDI_VID, XSENS_CONVERTER_4_PID) }, { USB_DEVICE(FTDI_VID, XSENS_CONVERTER_5_PID) }, { USB_DEVICE(FTDI_VID, XSENS_CONVERTER_6_PID) }, { USB_DEVICE(FTDI_VID, XSENS_CONVERTER_7_PID) }, { USB_DEVICE(MOBILITY_VID, MOBILITY_USB_SERIAL_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ACTIVE_ROBOTS_PID) }, { USB_DEVICE(FTDI_VID, FTDI_MHAM_KW_PID) }, { USB_DEVICE(FTDI_VID, FTDI_MHAM_YS_PID) }, { USB_DEVICE(FTDI_VID, FTDI_MHAM_Y6_PID) }, { USB_DEVICE(FTDI_VID, FTDI_MHAM_Y8_PID) }, { USB_DEVICE(FTDI_VID, FTDI_MHAM_IC_PID) }, { USB_DEVICE(FTDI_VID, FTDI_MHAM_DB9_PID) }, { USB_DEVICE(FTDI_VID, FTDI_MHAM_RS232_PID) }, { USB_DEVICE(FTDI_VID, FTDI_MHAM_Y9_PID) }, { USB_DEVICE(FTDI_VID, FTDI_TERATRONIK_VCP_PID) }, { USB_DEVICE(FTDI_VID, FTDI_TERATRONIK_D2XX_PID) }, { USB_DEVICE(EVOLUTION_VID, EVOLUTION_ER1_PID) }, { USB_DEVICE(EVOLUTION_VID, EVO_HYBRID_PID) }, { USB_DEVICE(EVOLUTION_VID, EVO_RCM4_PID) }, { USB_DEVICE(CONTEC_VID, CONTEC_COM1USBH_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ARTEMIS_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ATIK_ATK16_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ATIK_ATK16C_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ATIK_ATK16HR_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ATIK_ATK16HRC_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ATIK_ATK16IC_PID) }, { USB_DEVICE(KOBIL_VID, KOBIL_CONV_B1_PID) }, { USB_DEVICE(KOBIL_VID, KOBIL_CONV_KAAN_PID) }, { USB_DEVICE(POSIFLEX_VID, POSIFLEX_PP7000_PID) }, { USB_DEVICE(FTDI_VID, FTDI_TTUSB_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ECLO_COM_1WIRE_PID) }, { USB_DEVICE(FTDI_VID, FTDI_WESTREX_MODEL_777_PID) }, { USB_DEVICE(FTDI_VID, FTDI_WESTREX_MODEL_8900F_PID) }, { USB_DEVICE(FTDI_VID, FTDI_PCDJ_DAC2_PID) }, { USB_DEVICE(FTDI_VID, FTDI_RRCIRKITS_LOCOBUFFER_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ASK_RDR400_PID) }, { USB_DEVICE(ICOM_VID, ICOM_ID_1_PID) }, { USB_DEVICE(ICOM_VID, ICOM_OPC_U_UC_PID) }, { USB_DEVICE(ICOM_VID, ICOM_ID_RP2C1_PID) }, { USB_DEVICE(ICOM_VID, ICOM_ID_RP2C2_PID) }, { USB_DEVICE(ICOM_VID, ICOM_ID_RP2D_PID) }, { USB_DEVICE(ICOM_VID, ICOM_ID_RP2VT_PID) }, { USB_DEVICE(ICOM_VID, ICOM_ID_RP2VR_PID) }, { USB_DEVICE(ICOM_VID, ICOM_ID_RP4KVT_PID) }, { USB_DEVICE(ICOM_VID, ICOM_ID_RP4KVR_PID) }, { USB_DEVICE(ICOM_VID, ICOM_ID_RP2KVT_PID) }, { USB_DEVICE(ICOM_VID, ICOM_ID_RP2KVR_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ACG_HFDUAL_PID) }, { USB_DEVICE(FTDI_VID, FTDI_YEI_SERVOCENTER31_PID) }, { USB_DEVICE(FTDI_VID, FTDI_THORLABS_PID) }, { USB_DEVICE(TESTO_VID, TESTO_USB_INTERFACE_PID) }, { USB_DEVICE(FTDI_VID, FTDI_GAMMA_SCOUT_PID) }, { USB_DEVICE(FTDI_VID, FTDI_TACTRIX_OPENPORT_13M_PID) }, { USB_DEVICE(FTDI_VID, FTDI_TACTRIX_OPENPORT_13S_PID) }, { USB_DEVICE(FTDI_VID, FTDI_TACTRIX_OPENPORT_13U_PID) }, { USB_DEVICE(ELEKTOR_VID, ELEKTOR_FT323R_PID) }, { USB_DEVICE(FTDI_VID, FTDI_NDI_HUC_PID), .driver_info = (kernel_ulong_t)&ftdi_NDI_device_quirk }, { USB_DEVICE(FTDI_VID, FTDI_NDI_SPECTRA_SCU_PID), .driver_info = (kernel_ulong_t)&ftdi_NDI_device_quirk }, { USB_DEVICE(FTDI_VID, FTDI_NDI_FUTURE_2_PID), .driver_info = (kernel_ulong_t)&ftdi_NDI_device_quirk }, { USB_DEVICE(FTDI_VID, FTDI_NDI_FUTURE_3_PID), .driver_info = (kernel_ulong_t)&ftdi_NDI_device_quirk }, { USB_DEVICE(FTDI_VID, FTDI_NDI_AURORA_SCU_PID), .driver_info = (kernel_ulong_t)&ftdi_NDI_device_quirk }, { USB_DEVICE(TELLDUS_VID, TELLDUS_TELLSTICK_PID) }, { USB_DEVICE(RTSYSTEMS_VID, RTSYSTEMS_SERIAL_VX7_PID) }, { USB_DEVICE(RTSYSTEMS_VID, RTSYSTEMS_CT29B_PID) }, { USB_DEVICE(FTDI_VID, FTDI_MAXSTREAM_PID) }, { USB_DEVICE(FTDI_VID, FTDI_PHI_FISCO_PID) }, { USB_DEVICE(TML_VID, TML_USB_SERIAL_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ELSTER_UNICOM_PID) }, { USB_DEVICE(FTDI_VID, FTDI_PROPOX_JTAGCABLEII_PID) }, { USB_DEVICE(FTDI_VID, FTDI_PROPOX_ISPCABLEIII_PID) }, { USB_DEVICE(OLIMEX_VID, OLIMEX_ARM_USB_OCD_PID), .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk }, { USB_DEVICE(FIC_VID, FIC_NEO1973_DEBUG_PID), .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk }, { USB_DEVICE(FTDI_VID, FTDI_OOCDLINK_PID), .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk }, { USB_DEVICE(FTDI_VID, LMI_LM3S_DEVEL_BOARD_PID), .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk }, { USB_DEVICE(FTDI_VID, LMI_LM3S_EVAL_BOARD_PID), .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk }, { USB_DEVICE(FTDI_VID, LMI_LM3S_ICDI_BOARD_PID), .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk }, { USB_DEVICE(FTDI_VID, FTDI_TURTELIZER_PID), .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk }, { USB_DEVICE(RATOC_VENDOR_ID, RATOC_PRODUCT_ID_USB60F) }, { USB_DEVICE(FTDI_VID, FTDI_REU_TINY_PID) }, /* Papouch devices based on FTDI chip */ { USB_DEVICE(PAPOUCH_VID, PAPOUCH_SB485_PID) }, { USB_DEVICE(PAPOUCH_VID, PAPOUCH_AP485_PID) }, { USB_DEVICE(PAPOUCH_VID, PAPOUCH_SB422_PID) }, { USB_DEVICE(PAPOUCH_VID, PAPOUCH_SB485_2_PID) }, { USB_DEVICE(PAPOUCH_VID, PAPOUCH_AP485_2_PID) }, { USB_DEVICE(PAPOUCH_VID, PAPOUCH_SB422_2_PID) }, { USB_DEVICE(PAPOUCH_VID, PAPOUCH_SB485S_PID) }, { USB_DEVICE(PAPOUCH_VID, PAPOUCH_SB485C_PID) }, { USB_DEVICE(PAPOUCH_VID, PAPOUCH_LEC_PID) }, { USB_DEVICE(PAPOUCH_VID, PAPOUCH_SB232_PID) }, { USB_DEVICE(PAPOUCH_VID, PAPOUCH_TMU_PID) }, { USB_DEVICE(PAPOUCH_VID, PAPOUCH_IRAMP_PID) }, { USB_DEVICE(PAPOUCH_VID, PAPOUCH_DRAK5_PID) }, { USB_DEVICE(PAPOUCH_VID, PAPOUCH_QUIDO8x8_PID) }, { USB_DEVICE(PAPOUCH_VID, PAPOUCH_QUIDO4x4_PID) }, { USB_DEVICE(PAPOUCH_VID, PAPOUCH_QUIDO2x2_PID) }, { USB_DEVICE(PAPOUCH_VID, PAPOUCH_QUIDO10x1_PID) }, { USB_DEVICE(PAPOUCH_VID, PAPOUCH_QUIDO30x3_PID) }, { USB_DEVICE(PAPOUCH_VID, PAPOUCH_QUIDO60x3_PID) }, { USB_DEVICE(PAPOUCH_VID, PAPOUCH_QUIDO2x16_PID) }, { USB_DEVICE(PAPOUCH_VID, PAPOUCH_QUIDO3x32_PID) }, { USB_DEVICE(PAPOUCH_VID, PAPOUCH_DRAK6_PID) }, { USB_DEVICE(PAPOUCH_VID, PAPOUCH_UPSUSB_PID) }, { USB_DEVICE(PAPOUCH_VID, PAPOUCH_MU_PID) }, { USB_DEVICE(PAPOUCH_VID, PAPOUCH_SIMUKEY_PID) }, { USB_DEVICE(PAPOUCH_VID, PAPOUCH_AD4USB_PID) }, { USB_DEVICE(PAPOUCH_VID, PAPOUCH_GMUX_PID) }, { USB_DEVICE(PAPOUCH_VID, PAPOUCH_GMSR_PID) }, { USB_DEVICE(FTDI_VID, FTDI_DOMINTELL_DGQG_PID) }, { USB_DEVICE(FTDI_VID, FTDI_DOMINTELL_DUSB_PID) }, { USB_DEVICE(ALTI2_VID, ALTI2_N3_PID) }, { USB_DEVICE(FTDI_VID, DIEBOLD_BCS_SE923_PID) }, { USB_DEVICE(ATMEL_VID, STK541_PID) }, { USB_DEVICE(DE_VID, STB_PID) }, { USB_DEVICE(DE_VID, WHT_PID) }, { USB_DEVICE(ADI_VID, ADI_GNICE_PID), .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk }, { USB_DEVICE(ADI_VID, ADI_GNICEPLUS_PID), .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk }, { USB_DEVICE(HORNBY_VID, HORNBY_ELITE_PID) }, { USB_DEVICE(JETI_VID, JETI_SPC1201_PID) }, { USB_DEVICE(MARVELL_VID, MARVELL_SHEEVAPLUG_PID), .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk }, { USB_DEVICE(LARSENBRUSGAARD_VID, LB_ALTITRACK_PID) }, { USB_DEVICE(GN_OTOMETRICS_VID, AURICAL_USB_PID) }, { USB_DEVICE(BAYER_VID, BAYER_CONTOUR_CABLE_PID) }, { USB_DEVICE(FTDI_VID, MARVELL_OPENRD_PID), .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk }, { USB_DEVICE(FTDI_VID, TI_XDS100V2_PID), .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk }, { USB_DEVICE(FTDI_VID, HAMEG_HO820_PID) }, { USB_DEVICE(FTDI_VID, HAMEG_HO720_PID) }, { USB_DEVICE(FTDI_VID, HAMEG_HO730_PID) }, { USB_DEVICE(FTDI_VID, HAMEG_HO870_PID) }, { USB_DEVICE(FTDI_VID, MJSG_GENERIC_PID) }, { USB_DEVICE(FTDI_VID, MJSG_SR_RADIO_PID) }, { USB_DEVICE(FTDI_VID, MJSG_HD_RADIO_PID) }, { USB_DEVICE(FTDI_VID, MJSG_XM_RADIO_PID) }, { USB_DEVICE(FTDI_VID, XVERVE_SIGNALYZER_ST_PID), .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk }, { USB_DEVICE(FTDI_VID, XVERVE_SIGNALYZER_SLITE_PID), .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk }, { USB_DEVICE(FTDI_VID, XVERVE_SIGNALYZER_SH2_PID), .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk }, { USB_DEVICE(FTDI_VID, XVERVE_SIGNALYZER_SH4_PID), .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk }, { USB_DEVICE(FTDI_VID, SEGWAY_RMP200_PID) }, { USB_DEVICE(FTDI_VID, ACCESIO_COM4SM_PID) }, { USB_DEVICE(IONICS_VID, IONICS_PLUGCOMPUTER_PID), .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk }, { USB_DEVICE(FTDI_VID, FTDI_CHAMSYS_24_MASTER_WING_PID) }, { USB_DEVICE(FTDI_VID, FTDI_CHAMSYS_PC_WING_PID) }, { USB_DEVICE(FTDI_VID, FTDI_CHAMSYS_USB_DMX_PID) }, { USB_DEVICE(FTDI_VID, FTDI_CHAMSYS_MIDI_TIMECODE_PID) }, { USB_DEVICE(FTDI_VID, FTDI_CHAMSYS_MINI_WING_PID) }, { USB_DEVICE(FTDI_VID, FTDI_CHAMSYS_MAXI_WING_PID) }, { USB_DEVICE(FTDI_VID, FTDI_CHAMSYS_MEDIA_WING_PID) }, { USB_DEVICE(FTDI_VID, FTDI_CHAMSYS_WING_PID) }, { USB_DEVICE(FTDI_VID, FTDI_SCIENCESCOPE_LOGBOOKML_PID) }, { USB_DEVICE(FTDI_VID, FTDI_SCIENCESCOPE_LS_LOGBOOK_PID) }, { USB_DEVICE(FTDI_VID, FTDI_SCIENCESCOPE_HS_LOGBOOK_PID) }, { USB_DEVICE(FTDI_VID, FTDI_CINTERION_MC55I_PID) }, { USB_DEVICE(FTDI_VID, FTDI_DOTEC_PID) }, { USB_DEVICE(QIHARDWARE_VID, MILKYMISTONE_JTAGSERIAL_PID), .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk }, { USB_DEVICE(ST_VID, ST_STMCLT1030_PID), .driver_info = (kernel_ulong_t)&ftdi_stmclite_quirk }, { USB_DEVICE(FTDI_VID, FTDI_RF_R106) }, { }, /* Optional parameter entry */ { } /* Terminating entry */ }; MODULE_DEVICE_TABLE(usb, id_table_combined); static struct usb_driver ftdi_driver = { .name = "ftdi_sio", .probe = usb_serial_probe, .disconnect = usb_serial_disconnect, .id_table = id_table_combined, .no_dynamic_id = 1, }; static const char *ftdi_chip_name[] = { [SIO] = "SIO", /* the serial part of FT8U100AX */ [FT8U232AM] = "FT8U232AM", [FT232BM] = "FT232BM", [FT2232C] = "FT2232C", [FT232RL] = "FT232RL", [FT2232H] = "FT2232H", [FT4232H] = "FT4232H" }; /* Constants for read urb and write urb */ #define BUFSZ 512 /* Used for TIOCMIWAIT */ #define FTDI_STATUS_B0_MASK (FTDI_RS0_CTS | FTDI_RS0_DSR | FTDI_RS0_RI | FTDI_RS0_RLSD) #define FTDI_STATUS_B1_MASK (FTDI_RS_BI) /* End TIOCMIWAIT */ #define FTDI_IMPL_ASYNC_FLAGS = (ASYNC_SPD_HI | ASYNC_SPD_VHI \ | ASYNC_SPD_CUST | ASYNC_SPD_SHI | ASYNC_SPD_WARP) /* function prototypes for a FTDI serial converter */ static int ftdi_sio_probe(struct usb_serial *serial, const struct usb_device_id *id); static int ftdi_sio_port_probe(struct usb_serial_port *port); static int ftdi_sio_port_remove(struct usb_serial_port *port); static int ftdi_open(struct tty_struct *tty, struct usb_serial_port *port); static void ftdi_close(struct usb_serial_port *port); static void ftdi_dtr_rts(struct usb_serial_port *port, int on); static int ftdi_write(struct tty_struct *tty, struct usb_serial_port *port, const unsigned char *buf, int count); static int ftdi_write_room(struct tty_struct *tty); static int ftdi_chars_in_buffer(struct tty_struct *tty); static void ftdi_write_bulk_callback(struct urb *urb); static void ftdi_read_bulk_callback(struct urb *urb); static void ftdi_process_read(struct usb_serial_port *port); static void ftdi_set_termios(struct tty_struct *tty, struct usb_serial_port *port, struct ktermios *old); static int ftdi_tiocmget(struct tty_struct *tty, struct file *file); static int ftdi_tiocmset(struct tty_struct *tty, struct file *file, unsigned int set, unsigned int clear); static int ftdi_ioctl(struct tty_struct *tty, struct file *file, unsigned int cmd, unsigned long arg); static void ftdi_break_ctl(struct tty_struct *tty, int break_state); static void ftdi_throttle(struct tty_struct *tty); static void ftdi_unthrottle(struct tty_struct *tty); static unsigned short int ftdi_232am_baud_base_to_divisor(int baud, int base); static unsigned short int ftdi_232am_baud_to_divisor(int baud); static __u32 ftdi_232bm_baud_base_to_divisor(int baud, int base); static __u32 ftdi_232bm_baud_to_divisor(int baud); static __u32 ftdi_2232h_baud_base_to_divisor(int baud, int base); static __u32 ftdi_2232h_baud_to_divisor(int baud); static struct usb_serial_driver ftdi_sio_device = { .driver = { .owner = THIS_MODULE, .name = "ftdi_sio", }, .description = "FTDI USB Serial Device", .usb_driver = &ftdi_driver , .id_table = id_table_combined, .num_ports = 1, .probe = ftdi_sio_probe, .port_probe = ftdi_sio_port_probe, .port_remove = ftdi_sio_port_remove, .open = ftdi_open, .close = ftdi_close, .dtr_rts = ftdi_dtr_rts, .throttle = ftdi_throttle, .unthrottle = ftdi_unthrottle, .write = ftdi_write, .write_room = ftdi_write_room, .chars_in_buffer = ftdi_chars_in_buffer, .read_bulk_callback = ftdi_read_bulk_callback, .write_bulk_callback = ftdi_write_bulk_callback, .tiocmget = ftdi_tiocmget, .tiocmset = ftdi_tiocmset, .ioctl = ftdi_ioctl, .set_termios = ftdi_set_termios, .break_ctl = ftdi_break_ctl, }; #define WDR_TIMEOUT 5000 /* default urb timeout */ #define WDR_SHORT_TIMEOUT 1000 /* shorter urb timeout */ /* High and low are for DTR, RTS etc etc */ #define HIGH 1 #define LOW 0 /* number of outstanding urbs to prevent userspace DoS from happening */ #define URB_UPPER_LIMIT 42 /* * *************************************************************************** * Utility functions * *************************************************************************** */ static unsigned short int ftdi_232am_baud_base_to_divisor(int baud, int base) { unsigned short int divisor; /* divisor shifted 3 bits to the left */ int divisor3 = base / 2 / baud; if ((divisor3 & 0x7) == 7) divisor3++; /* round x.7/8 up to x+1 */ divisor = divisor3 >> 3; divisor3 &= 0x7; if (divisor3 == 1) divisor |= 0xc000; else if (divisor3 >= 4) divisor |= 0x4000; else if (divisor3 != 0) divisor |= 0x8000; else if (divisor == 1) divisor = 0; /* special case for maximum baud rate */ return divisor; } static unsigned short int ftdi_232am_baud_to_divisor(int baud) { return ftdi_232am_baud_base_to_divisor(baud, 48000000); } static __u32 ftdi_232bm_baud_base_to_divisor(int baud, int base) { static const unsigned char divfrac[8] = { 0, 3, 2, 4, 1, 5, 6, 7 }; __u32 divisor; /* divisor shifted 3 bits to the left */ int divisor3 = base / 2 / baud; divisor = divisor3 >> 3; divisor |= (__u32)divfrac[divisor3 & 0x7] << 14; /* Deal with special cases for highest baud rates. */ if (divisor == 1) divisor = 0; else if (divisor == 0x4001) divisor = 1; return divisor; } static __u32 ftdi_232bm_baud_to_divisor(int baud) { return ftdi_232bm_baud_base_to_divisor(baud, 48000000); } static __u32 ftdi_2232h_baud_base_to_divisor(int baud, int base) { static const unsigned char divfrac[8] = { 0, 3, 2, 4, 1, 5, 6, 7 }; __u32 divisor; int divisor3; /* hi-speed baud rate is 10-bit sampling instead of 16-bit */ divisor3 = (base / 10 / baud) * 8; divisor = divisor3 >> 3; divisor |= (__u32)divfrac[divisor3 & 0x7] << 14; /* Deal with special cases for highest baud rates. */ if (divisor == 1) divisor = 0; else if (divisor == 0x4001) divisor = 1; /* * Set this bit to turn off a divide by 2.5 on baud rate generator * This enables baud rates up to 12Mbaud but cannot reach below 1200 * baud with this bit set */ divisor |= 0x00020000; return divisor; } static __u32 ftdi_2232h_baud_to_divisor(int baud) { return ftdi_2232h_baud_base_to_divisor(baud, 120000000); } #define set_mctrl(port, set) update_mctrl((port), (set), 0) #define clear_mctrl(port, clear) update_mctrl((port), 0, (clear)) static int update_mctrl(struct usb_serial_port *port, unsigned int set, unsigned int clear) { struct ftdi_private *priv = usb_get_serial_port_data(port); char *buf; unsigned urb_value; int rv; if (((set | clear) & (TIOCM_DTR | TIOCM_RTS)) == 0) { dbg("%s - DTR|RTS not being set|cleared", __func__); return 0; /* no change */ } buf = kmalloc(1, GFP_NOIO); if (!buf) return -ENOMEM; clear &= ~set; /* 'set' takes precedence over 'clear' */ urb_value = 0; if (clear & TIOCM_DTR) urb_value |= FTDI_SIO_SET_DTR_LOW; if (clear & TIOCM_RTS) urb_value |= FTDI_SIO_SET_RTS_LOW; if (set & TIOCM_DTR) urb_value |= FTDI_SIO_SET_DTR_HIGH; if (set & TIOCM_RTS) urb_value |= FTDI_SIO_SET_RTS_HIGH; rv = usb_control_msg(port->serial->dev, usb_sndctrlpipe(port->serial->dev, 0), FTDI_SIO_SET_MODEM_CTRL_REQUEST, FTDI_SIO_SET_MODEM_CTRL_REQUEST_TYPE, urb_value, priv->interface, buf, 0, WDR_TIMEOUT); kfree(buf); if (rv < 0) { dbg("%s Error from MODEM_CTRL urb: DTR %s, RTS %s", __func__, (set & TIOCM_DTR) ? "HIGH" : (clear & TIOCM_DTR) ? "LOW" : "unchanged", (set & TIOCM_RTS) ? "HIGH" : (clear & TIOCM_RTS) ? "LOW" : "unchanged"); } else { dbg("%s - DTR %s, RTS %s", __func__, (set & TIOCM_DTR) ? "HIGH" : (clear & TIOCM_DTR) ? "LOW" : "unchanged", (set & TIOCM_RTS) ? "HIGH" : (clear & TIOCM_RTS) ? "LOW" : "unchanged"); /* FIXME: locking on last_dtr_rts */ priv->last_dtr_rts = (priv->last_dtr_rts & ~clear) | set; } return rv; } static __u32 get_ftdi_divisor(struct tty_struct *tty, struct usb_serial_port *port) { /* get_ftdi_divisor */ struct ftdi_private *priv = usb_get_serial_port_data(port); __u32 div_value = 0; int div_okay = 1; int baud; /* * The logic involved in setting the baudrate can be cleanly split into * 3 steps. * 1. Standard baud rates are set in tty->termios->c_cflag * 2. If these are not enough, you can set any speed using alt_speed as * follows: * - set tty->termios->c_cflag speed to B38400 * - set your real speed in tty->alt_speed; it gets ignored when * alt_speed==0, (or) * - call TIOCSSERIAL ioctl with (struct serial_struct) set as * follows: * flags & ASYNC_SPD_MASK == ASYNC_SPD_[HI, VHI, SHI, WARP], * this just sets alt_speed to (HI: 57600, VHI: 115200, * SHI: 230400, WARP: 460800) * ** Steps 1, 2 are done courtesy of tty_get_baud_rate * 3. You can also set baud rate by setting custom divisor as follows * - set tty->termios->c_cflag speed to B38400 * - call TIOCSSERIAL ioctl with (struct serial_struct) set as * follows: * o flags & ASYNC_SPD_MASK == ASYNC_SPD_CUST * o custom_divisor set to baud_base / your_new_baudrate * ** Step 3 is done courtesy of code borrowed from serial.c * I should really spend some time and separate + move this common * code to serial.c, it is replicated in nearly every serial driver * you see. */ /* 1. Get the baud rate from the tty settings, this observes alt_speed hack */ baud = tty_get_baud_rate(tty); dbg("%s - tty_get_baud_rate reports speed %d", __func__, baud); /* 2. Observe async-compatible custom_divisor hack, update baudrate if needed */ if (baud == 38400 && ((priv->flags & ASYNC_SPD_MASK) == ASYNC_SPD_CUST) && (priv->custom_divisor)) { baud = priv->baud_base / priv->custom_divisor; dbg("%s - custom divisor %d sets baud rate to %d", __func__, priv->custom_divisor, baud); } /* 3. Convert baudrate to device-specific divisor */ if (!baud) baud = 9600; switch (priv->chip_type) { case SIO: /* SIO chip */ switch (baud) { case 300: div_value = ftdi_sio_b300; break; case 600: div_value = ftdi_sio_b600; break; case 1200: div_value = ftdi_sio_b1200; break; case 2400: div_value = ftdi_sio_b2400; break; case 4800: div_value = ftdi_sio_b4800; break; case 9600: div_value = ftdi_sio_b9600; break; case 19200: div_value = ftdi_sio_b19200; break; case 38400: div_value = ftdi_sio_b38400; break; case 57600: div_value = ftdi_sio_b57600; break; case 115200: div_value = ftdi_sio_b115200; break; } /* baud */ if (div_value == 0) { dbg("%s - Baudrate (%d) requested is not supported", __func__, baud); div_value = ftdi_sio_b9600; baud = 9600; div_okay = 0; } break; case FT8U232AM: /* 8U232AM chip */ if (baud <= 3000000) { div_value = ftdi_232am_baud_to_divisor(baud); } else { dbg("%s - Baud rate too high!", __func__); baud = 9600; div_value = ftdi_232am_baud_to_divisor(9600); div_okay = 0; } break; case FT232BM: /* FT232BM chip */ case FT2232C: /* FT2232C chip */ case FT232RL: if (baud <= 3000000) { __u16 product_id = le16_to_cpu( port->serial->dev->descriptor.idProduct); if (((FTDI_NDI_HUC_PID == product_id) || (FTDI_NDI_SPECTRA_SCU_PID == product_id) || (FTDI_NDI_FUTURE_2_PID == product_id) || (FTDI_NDI_FUTURE_3_PID == product_id) || (FTDI_NDI_AURORA_SCU_PID == product_id)) && (baud == 19200)) { baud = 1200000; } div_value = ftdi_232bm_baud_to_divisor(baud); } else { dbg("%s - Baud rate too high!", __func__); div_value = ftdi_232bm_baud_to_divisor(9600); div_okay = 0; baud = 9600; } break; case FT2232H: /* FT2232H chip */ case FT4232H: /* FT4232H chip */ if ((baud <= 12000000) & (baud >= 1200)) { div_value = ftdi_2232h_baud_to_divisor(baud); } else if (baud < 1200) { div_value = ftdi_232bm_baud_to_divisor(baud); } else { dbg("%s - Baud rate too high!", __func__); div_value = ftdi_232bm_baud_to_divisor(9600); div_okay = 0; baud = 9600; } break; } /* priv->chip_type */ if (div_okay) { dbg("%s - Baud rate set to %d (divisor 0x%lX) on chip %s", __func__, baud, (unsigned long)div_value, ftdi_chip_name[priv->chip_type]); } tty_encode_baud_rate(tty, baud, baud); return div_value; } static int change_speed(struct tty_struct *tty, struct usb_serial_port *port) { struct ftdi_private *priv = usb_get_serial_port_data(port); char *buf; __u16 urb_value; __u16 urb_index; __u32 urb_index_value; int rv; buf = kmalloc(1, GFP_NOIO); if (!buf) return -ENOMEM; urb_index_value = get_ftdi_divisor(tty, port); urb_value = (__u16)urb_index_value; urb_index = (__u16)(urb_index_value >> 16); if (priv->interface) { /* FT2232C */ urb_index = (__u16)((urb_index << 8) | priv->interface); } rv = usb_control_msg(port->serial->dev, usb_sndctrlpipe(port->serial->dev, 0), FTDI_SIO_SET_BAUDRATE_REQUEST, FTDI_SIO_SET_BAUDRATE_REQUEST_TYPE, urb_value, urb_index, buf, 0, WDR_SHORT_TIMEOUT); kfree(buf); return rv; } static int write_latency_timer(struct usb_serial_port *port) { struct ftdi_private *priv = usb_get_serial_port_data(port); struct usb_device *udev = port->serial->dev; char buf[1]; int rv = 0; int l = priv->latency; if (priv->flags & ASYNC_LOW_LATENCY) l = 1; dbg("%s: setting latency timer = %i", __func__, l); rv = usb_control_msg(udev, usb_sndctrlpipe(udev, 0), FTDI_SIO_SET_LATENCY_TIMER_REQUEST, FTDI_SIO_SET_LATENCY_TIMER_REQUEST_TYPE, l, priv->interface, buf, 0, WDR_TIMEOUT); if (rv < 0) dev_err(&port->dev, "Unable to write latency timer: %i\n", rv); return rv; } static int read_latency_timer(struct usb_serial_port *port) { struct ftdi_private *priv = usb_get_serial_port_data(port); struct usb_device *udev = port->serial->dev; unsigned short latency = 0; int rv = 0; dbg("%s", __func__); rv = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0), FTDI_SIO_GET_LATENCY_TIMER_REQUEST, FTDI_SIO_GET_LATENCY_TIMER_REQUEST_TYPE, 0, priv->interface, (char *) &latency, 1, WDR_TIMEOUT); if (rv < 0) { dev_err(&port->dev, "Unable to read latency timer: %i\n", rv); return -EIO; } return latency; } static int get_serial_info(struct usb_serial_port *port, struct serial_struct __user *retinfo) { struct ftdi_private *priv = usb_get_serial_port_data(port); struct serial_struct tmp; if (!retinfo) return -EFAULT; memset(&tmp, 0, sizeof(tmp)); tmp.flags = priv->flags; tmp.baud_base = priv->baud_base; tmp.custom_divisor = priv->custom_divisor; if (copy_to_user(retinfo, &tmp, sizeof(*retinfo))) return -EFAULT; return 0; } /* get_serial_info */ static int set_serial_info(struct tty_struct *tty, struct usb_serial_port *port, struct serial_struct __user *newinfo) { /* set_serial_info */ struct ftdi_private *priv = usb_get_serial_port_data(port); struct serial_struct new_serial; struct ftdi_private old_priv; if (copy_from_user(&new_serial, newinfo, sizeof(new_serial))) return -EFAULT; lock_kernel(); old_priv = *priv; /* Do error checking and permission checking */ if (!capable(CAP_SYS_ADMIN)) { if (((new_serial.flags & ~ASYNC_USR_MASK) != (priv->flags & ~ASYNC_USR_MASK))) { unlock_kernel(); return -EPERM; } priv->flags = ((priv->flags & ~ASYNC_USR_MASK) | (new_serial.flags & ASYNC_USR_MASK)); priv->custom_divisor = new_serial.custom_divisor; goto check_and_exit; } if (new_serial.baud_base != priv->baud_base) { unlock_kernel(); return -EINVAL; } /* Make the changes - these are privileged changes! */ priv->flags = ((priv->flags & ~ASYNC_FLAGS) | (new_serial.flags & ASYNC_FLAGS)); priv->custom_divisor = new_serial.custom_divisor; write_latency_timer(port); check_and_exit: if ((old_priv.flags & ASYNC_SPD_MASK) != (priv->flags & ASYNC_SPD_MASK)) { if ((priv->flags & ASYNC_SPD_MASK) == ASYNC_SPD_HI) tty->alt_speed = 57600; else if ((priv->flags & ASYNC_SPD_MASK) == ASYNC_SPD_VHI) tty->alt_speed = 115200; else if ((priv->flags & ASYNC_SPD_MASK) == ASYNC_SPD_SHI) tty->alt_speed = 230400; else if ((priv->flags & ASYNC_SPD_MASK) == ASYNC_SPD_WARP) tty->alt_speed = 460800; else tty->alt_speed = 0; } if (((old_priv.flags & ASYNC_SPD_MASK) != (priv->flags & ASYNC_SPD_MASK)) || (((priv->flags & ASYNC_SPD_MASK) == ASYNC_SPD_CUST) && (old_priv.custom_divisor != priv->custom_divisor))) { unlock_kernel(); change_speed(tty, port); } else unlock_kernel(); return 0; } /* set_serial_info */ /* Determine type of FTDI chip based on USB config and descriptor. */ static void ftdi_determine_type(struct usb_serial_port *port) { struct ftdi_private *priv = usb_get_serial_port_data(port); struct usb_serial *serial = port->serial; struct usb_device *udev = serial->dev; unsigned version; unsigned interfaces; /* Assume it is not the original SIO device for now. */ priv->baud_base = 48000000 / 2; priv->write_offset = 0; version = le16_to_cpu(udev->descriptor.bcdDevice); interfaces = udev->actconfig->desc.bNumInterfaces; dbg("%s: bcdDevice = 0x%x, bNumInterfaces = %u", __func__, version, interfaces); if (interfaces > 1) { int inter; /* Multiple interfaces.*/ if (version == 0x0800) { priv->chip_type = FT4232H; /* Hi-speed - baud clock runs at 120MHz */ priv->baud_base = 120000000 / 2; } else if (version == 0x0700) { priv->chip_type = FT2232H; /* Hi-speed - baud clock runs at 120MHz */ priv->baud_base = 120000000 / 2; } else priv->chip_type = FT2232C; /* Determine interface code. */ inter = serial->interface->altsetting->desc.bInterfaceNumber; if (inter == 0) { priv->interface = INTERFACE_A; } else if (inter == 1) { priv->interface = INTERFACE_B; } else if (inter == 2) { priv->interface = INTERFACE_C; } else if (inter == 3) { priv->interface = INTERFACE_D; } /* BM-type devices have a bug where bcdDevice gets set * to 0x200 when iSerialNumber is 0. */ if (version < 0x500) { dbg("%s: something fishy - bcdDevice too low for multi-interface device", __func__); } } else if (version < 0x200) { /* Old device. Assume its the original SIO. */ priv->chip_type = SIO; priv->baud_base = 12000000 / 16; priv->write_offset = 1; } else if (version < 0x400) { /* Assume its an FT8U232AM (or FT8U245AM) */ /* (It might be a BM because of the iSerialNumber bug, * but it will still work as an AM device.) */ priv->chip_type = FT8U232AM; } else if (version < 0x600) { /* Assume its an FT232BM (or FT245BM) */ priv->chip_type = FT232BM; } else { /* Assume its an FT232R */ priv->chip_type = FT232RL; } dev_info(&udev->dev, "Detected %s\n", ftdi_chip_name[priv->chip_type]); } /* Determine the maximum packet size for the device. This depends on the chip * type and the USB host capabilities. The value should be obtained from the * device descriptor as the chip will use the appropriate values for the host.*/ static void ftdi_set_max_packet_size(struct usb_serial_port *port) { struct ftdi_private *priv = usb_get_serial_port_data(port); struct usb_serial *serial = port->serial; struct usb_device *udev = serial->dev; struct usb_interface *interface = serial->interface; struct usb_endpoint_descriptor *ep_desc = &interface->cur_altsetting->endpoint[1].desc; unsigned num_endpoints; int i = 0; num_endpoints = interface->cur_altsetting->desc.bNumEndpoints; dev_info(&udev->dev, "Number of endpoints %d\n", num_endpoints); /* NOTE: some customers have programmed FT232R/FT245R devices * with an endpoint size of 0 - not good. In this case, we * want to override the endpoint descriptor setting and use a * value of 64 for wMaxPacketSize */ for (i = 0; i < num_endpoints; i++) { dev_info(&udev->dev, "Endpoint %d MaxPacketSize %d\n", i+1, interface->cur_altsetting->endpoint[i].desc.wMaxPacketSize); ep_desc = &interface->cur_altsetting->endpoint[i].desc; if (ep_desc->wMaxPacketSize == 0) { ep_desc->wMaxPacketSize = cpu_to_le16(0x40); dev_info(&udev->dev, "Overriding wMaxPacketSize on endpoint %d\n", i); } } /* set max packet size based on descriptor */ priv->max_packet_size = le16_to_cpu(ep_desc->wMaxPacketSize); dev_info(&udev->dev, "Setting MaxPacketSize %d\n", priv->max_packet_size); } /* * *************************************************************************** * Sysfs Attribute * *************************************************************************** */ static ssize_t show_latency_timer(struct device *dev, struct device_attribute *attr, char *buf) { struct usb_serial_port *port = to_usb_serial_port(dev); struct ftdi_private *priv = usb_get_serial_port_data(port); if (priv->flags & ASYNC_LOW_LATENCY) return sprintf(buf, "1\n"); else return sprintf(buf, "%i\n", priv->latency); } /* Write a new value of the latency timer, in units of milliseconds. */ static ssize_t store_latency_timer(struct device *dev, struct device_attribute *attr, const char *valbuf, size_t count) { struct usb_serial_port *port = to_usb_serial_port(dev); struct ftdi_private *priv = usb_get_serial_port_data(port); int v = simple_strtoul(valbuf, NULL, 10); int rv = 0; priv->latency = v; rv = write_latency_timer(port); if (rv < 0) return -EIO; return count; } /* Write an event character directly to the FTDI register. The ASCII value is in the low 8 bits, with the enable bit in the 9th bit. */ static ssize_t store_event_char(struct device *dev, struct device_attribute *attr, const char *valbuf, size_t count) { struct usb_serial_port *port = to_usb_serial_port(dev); struct ftdi_private *priv = usb_get_serial_port_data(port); struct usb_device *udev = port->serial->dev; char buf[1]; int v = simple_strtoul(valbuf, NULL, 10); int rv = 0; dbg("%s: setting event char = %i", __func__, v); rv = usb_control_msg(udev, usb_sndctrlpipe(udev, 0), FTDI_SIO_SET_EVENT_CHAR_REQUEST, FTDI_SIO_SET_EVENT_CHAR_REQUEST_TYPE, v, priv->interface, buf, 0, WDR_TIMEOUT); if (rv < 0) { dbg("Unable to write event character: %i", rv); return -EIO; } return count; } static DEVICE_ATTR(latency_timer, S_IWUSR | S_IRUGO, show_latency_timer, store_latency_timer); static DEVICE_ATTR(event_char, S_IWUSR, NULL, store_event_char); static int create_sysfs_attrs(struct usb_serial_port *port) { struct ftdi_private *priv = usb_get_serial_port_data(port); int retval = 0; dbg("%s", __func__); /* XXX I've no idea if the original SIO supports the event_char * sysfs parameter, so I'm playing it safe. */ if (priv->chip_type != SIO) { dbg("sysfs attributes for %s", ftdi_chip_name[priv->chip_type]); retval = device_create_file(&port->dev, &dev_attr_event_char); if ((!retval) && (priv->chip_type == FT232BM || priv->chip_type == FT2232C || priv->chip_type == FT232RL || priv->chip_type == FT2232H || priv->chip_type == FT4232H)) { retval = device_create_file(&port->dev, &dev_attr_latency_timer); } } return retval; } static void remove_sysfs_attrs(struct usb_serial_port *port) { struct ftdi_private *priv = usb_get_serial_port_data(port); dbg("%s", __func__); /* XXX see create_sysfs_attrs */ if (priv->chip_type != SIO) { device_remove_file(&port->dev, &dev_attr_event_char); if (priv->chip_type == FT232BM || priv->chip_type == FT2232C || priv->chip_type == FT232RL || priv->chip_type == FT2232H || priv->chip_type == FT4232H) { device_remove_file(&port->dev, &dev_attr_latency_timer); } } } /* * *************************************************************************** * FTDI driver specific functions * *************************************************************************** */ /* Probe function to check for special devices */ static int ftdi_sio_probe(struct usb_serial *serial, const struct usb_device_id *id) { struct ftdi_sio_quirk *quirk = (struct ftdi_sio_quirk *)id->driver_info; if (quirk && quirk->probe) { int ret = quirk->probe(serial); if (ret != 0) return ret; } usb_set_serial_data(serial, (void *)id->driver_info); return 0; } static int ftdi_sio_port_probe(struct usb_serial_port *port) { struct ftdi_private *priv; struct ftdi_sio_quirk *quirk = usb_get_serial_data(port->serial); dbg("%s", __func__); priv = kzalloc(sizeof(struct ftdi_private), GFP_KERNEL); if (!priv) { dev_err(&port->dev, "%s- kmalloc(%Zd) failed.\n", __func__, sizeof(struct ftdi_private)); return -ENOMEM; } kref_init(&priv->kref); spin_lock_init(&priv->tx_lock); init_waitqueue_head(&priv->delta_msr_wait); /* This will push the characters through immediately rather than queue a task to deliver them */ priv->flags = ASYNC_LOW_LATENCY; if (quirk && quirk->port_probe) quirk->port_probe(priv); /* Increase the size of read buffers */ kfree(port->bulk_in_buffer); port->bulk_in_buffer = kmalloc(BUFSZ, GFP_KERNEL); if (!port->bulk_in_buffer) { kfree(priv); return -ENOMEM; } if (port->read_urb) { port->read_urb->transfer_buffer = port->bulk_in_buffer; port->read_urb->transfer_buffer_length = BUFSZ; } priv->port = port; /* Free port's existing write urb and transfer buffer. */ if (port->write_urb) { usb_free_urb(port->write_urb); port->write_urb = NULL; } kfree(port->bulk_out_buffer); port->bulk_out_buffer = NULL; usb_set_serial_port_data(port, priv); ftdi_determine_type(port); ftdi_set_max_packet_size(port); read_latency_timer(port); create_sysfs_attrs(port); return 0; } /* Setup for the USB-UIRT device, which requires hardwired * baudrate (38400 gets mapped to 312500) */ /* Called from usbserial:serial_probe */ static void ftdi_USB_UIRT_setup(struct ftdi_private *priv) { dbg("%s", __func__); priv->flags |= ASYNC_SPD_CUST; priv->custom_divisor = 77; priv->force_baud = 38400; } /* ftdi_USB_UIRT_setup */ /* Setup for the HE-TIRA1 device, which requires hardwired * baudrate (38400 gets mapped to 100000) and RTS-CTS enabled. */ static void ftdi_HE_TIRA1_setup(struct ftdi_private *priv) { dbg("%s", __func__); priv->flags |= ASYNC_SPD_CUST; priv->custom_divisor = 240; priv->force_baud = 38400; priv->force_rtscts = 1; } /* ftdi_HE_TIRA1_setup */ /* * Module parameter to control latency timer for NDI FTDI-based USB devices. * If this value is not set in modprobe.conf.local its value will be set to 1ms. */ static int ndi_latency_timer = 1; /* Setup for the NDI FTDI-based USB devices, which requires hardwired * baudrate (19200 gets mapped to 1200000). * * Called from usbserial:serial_probe. */ static int ftdi_NDI_device_setup(struct usb_serial *serial) { struct usb_device *udev = serial->dev; int latency = ndi_latency_timer; int rv = 0; char buf[1]; if (latency == 0) latency = 1; if (latency > 99) latency = 99; dbg("%s setting NDI device latency to %d", __func__, latency); dev_info(&udev->dev, "NDI device with a latency value of %d", latency); rv = usb_control_msg(udev, usb_sndctrlpipe(udev, 0), FTDI_SIO_SET_LATENCY_TIMER_REQUEST, FTDI_SIO_SET_LATENCY_TIMER_REQUEST_TYPE, latency, 0, buf, 0, WDR_TIMEOUT); return 0; } /* * First port on JTAG adaptors such as Olimex arm-usb-ocd or the FIC/OpenMoko * Neo1973 Debug Board is reserved for JTAG interface and can be accessed from * userspace using openocd. */ static int ftdi_jtag_probe(struct usb_serial *serial) { struct usb_device *udev = serial->dev; struct usb_interface *interface = serial->interface; dbg("%s", __func__); if (interface == udev->actconfig->interface[0]) { dev_info(&udev->dev, "Ignoring serial port reserved for JTAG\n"); return -ENODEV; } return 0; } static int ftdi_8u2232c_probe(struct usb_serial *serial) { struct usb_device *udev = serial->dev; dbg("%s", __func__); if ((udev->manufacturer) && (strcmp(udev->manufacturer, "CALAO Systems") == 0)) return ftdi_jtag_probe(serial); return 0; } /* * First and second port on STMCLiteadaptors is reserved for JTAG interface * and the forth port for pio */ static int ftdi_stmclite_probe(struct usb_serial *serial) { struct usb_device *udev = serial->dev; struct usb_interface *interface = serial->interface; dbg("%s", __func__); if (interface == udev->actconfig->interface[2]) return 0; dev_info(&udev->dev, "Ignoring serial port reserved for JTAG\n"); return -ENODEV; } /* * The Matrix Orbital VK204-25-USB has an invalid IN endpoint. * We have to correct it if we want to read from it. */ static int ftdi_mtxorb_hack_setup(struct usb_serial *serial) { struct usb_host_endpoint *ep = serial->dev->ep_in[1]; struct usb_endpoint_descriptor *ep_desc = &ep->desc; if (ep->enabled && ep_desc->wMaxPacketSize == 0) { ep_desc->wMaxPacketSize = cpu_to_le16(0x40); dev_info(&serial->dev->dev, "Fixing invalid wMaxPacketSize on read pipe\n"); } return 0; } static void ftdi_sio_priv_release(struct kref *k) { struct ftdi_private *priv = container_of(k, struct ftdi_private, kref); kfree(priv); } static int ftdi_sio_port_remove(struct usb_serial_port *port) { struct ftdi_private *priv = usb_get_serial_port_data(port); dbg("%s", __func__); remove_sysfs_attrs(port); kref_put(&priv->kref, ftdi_sio_priv_release); return 0; } static int ftdi_submit_read_urb(struct usb_serial_port *port, gfp_t mem_flags) { struct urb *urb = port->read_urb; struct usb_serial *serial = port->serial; int result; usb_fill_bulk_urb(urb, serial->dev, usb_rcvbulkpipe(serial->dev, port->bulk_in_endpointAddress), urb->transfer_buffer, urb->transfer_buffer_length, ftdi_read_bulk_callback, port); result = usb_submit_urb(urb, mem_flags); if (result) dev_err(&port->dev, "%s - failed submitting read urb, error %d\n", __func__, result); return result; } static int ftdi_open(struct tty_struct *tty, struct usb_serial_port *port) { /* ftdi_open */ struct ktermios dummy; struct usb_device *dev = port->serial->dev; struct ftdi_private *priv = usb_get_serial_port_data(port); unsigned long flags; int result = 0; char buf[1]; /* Needed for the usb_control_msg I think */ dbg("%s", __func__); spin_lock_irqsave(&priv->tx_lock, flags); priv->tx_bytes = 0; spin_unlock_irqrestore(&priv->tx_lock, flags); write_latency_timer(port); /* No error checking for this (will get errors later anyway) */ /* See ftdi_sio.h for description of what is reset */ usb_control_msg(dev, usb_sndctrlpipe(dev, 0), FTDI_SIO_RESET_REQUEST, FTDI_SIO_RESET_REQUEST_TYPE, FTDI_SIO_RESET_SIO, priv->interface, buf, 0, WDR_TIMEOUT); /* Termios defaults are set by usb_serial_init. We don't change port->tty->termios - this would lose speed settings, etc. This is same behaviour as serial.c/rs_open() - Kuba */ /* ftdi_set_termios will send usb control messages */ if (tty) { memset(&dummy, 0, sizeof(dummy)); ftdi_set_termios(tty, port, &dummy); } /* Not throttled */ spin_lock_irqsave(&port->lock, flags); port->throttled = 0; port->throttle_req = 0; spin_unlock_irqrestore(&port->lock, flags); /* Start reading from the device */ result = ftdi_submit_read_urb(port, GFP_KERNEL); if (!result) kref_get(&priv->kref); return result; } /* ftdi_open */ static void ftdi_dtr_rts(struct usb_serial_port *port, int on) { struct ftdi_private *priv = usb_get_serial_port_data(port); char buf[1]; mutex_lock(&port->serial->disc_mutex); if (!port->serial->disconnected) { /* Disable flow control */ if (!on && usb_control_msg(port->serial->dev, usb_sndctrlpipe(port->serial->dev, 0), FTDI_SIO_SET_FLOW_CTRL_REQUEST, FTDI_SIO_SET_FLOW_CTRL_REQUEST_TYPE, 0, priv->interface, buf, 0, WDR_TIMEOUT) < 0) { dev_err(&port->dev, "error from flowcontrol urb\n"); } /* drop RTS and DTR */ if (on) set_mctrl(port, TIOCM_DTR | TIOCM_RTS); else clear_mctrl(port, TIOCM_DTR | TIOCM_RTS); } mutex_unlock(&port->serial->disc_mutex); } /* * usbserial:__serial_close only calls ftdi_close if the point is open * * This only gets called when it is the last close * * */ static void ftdi_close(struct usb_serial_port *port) { /* ftdi_close */ struct ftdi_private *priv = usb_get_serial_port_data(port); dbg("%s", __func__); /* shutdown our bulk read */ usb_kill_urb(port->read_urb); kref_put(&priv->kref, ftdi_sio_priv_release); } /* ftdi_close */ /* The SIO requires the first byte to have: * B0 1 * B1 0 * B2..7 length of message excluding byte 0 * * The new devices do not require this byte */ static int ftdi_write(struct tty_struct *tty, struct usb_serial_port *port, const unsigned char *buf, int count) { /* ftdi_write */ struct ftdi_private *priv = usb_get_serial_port_data(port); struct urb *urb; unsigned char *buffer; int data_offset ; /* will be 1 for the SIO and 0 otherwise */ int status; int transfer_size; unsigned long flags; dbg("%s port %d, %d bytes", __func__, port->number, count); if (count == 0) { dbg("write request of 0 bytes"); return 0; } spin_lock_irqsave(&priv->tx_lock, flags); if (priv->tx_outstanding_urbs > URB_UPPER_LIMIT) { spin_unlock_irqrestore(&priv->tx_lock, flags); dbg("%s - write limit hit\n", __func__); return 0; } priv->tx_outstanding_urbs++; spin_unlock_irqrestore(&priv->tx_lock, flags); data_offset = priv->write_offset; dbg("data_offset set to %d", data_offset); /* Determine total transfer size */ transfer_size = count; if (data_offset > 0) { /* Original sio needs control bytes too... */ transfer_size += (data_offset * ((count + (priv->max_packet_size - 1 - data_offset)) / (priv->max_packet_size - data_offset))); } buffer = kmalloc(transfer_size, GFP_ATOMIC); if (!buffer) { dev_err(&port->dev, "%s ran out of kernel memory for urb ...\n", __func__); count = -ENOMEM; goto error_no_buffer; } urb = usb_alloc_urb(0, GFP_ATOMIC); if (!urb) { dev_err(&port->dev, "%s - no more free urbs\n", __func__); count = -ENOMEM; goto error_no_urb; } /* Copy data */ if (data_offset > 0) { /* Original sio requires control byte at start of each packet. */ int user_pktsz = priv->max_packet_size - data_offset; int todo = count; unsigned char *first_byte = buffer; const unsigned char *current_position = buf; while (todo > 0) { if (user_pktsz > todo) user_pktsz = todo; /* Write the control byte at the front of the packet*/ *first_byte = 1 | ((user_pktsz) << 2); /* Copy data for packet */ memcpy(first_byte + data_offset, current_position, user_pktsz); first_byte += user_pktsz + data_offset; current_position += user_pktsz; todo -= user_pktsz; } } else { /* No control byte required. */ /* Copy in the data to send */ memcpy(buffer, buf, count); } usb_serial_debug_data(debug, &port->dev, __func__, transfer_size, buffer); /* fill the buffer and send it */ usb_fill_bulk_urb(urb, port->serial->dev, usb_sndbulkpipe(port->serial->dev, port->bulk_out_endpointAddress), buffer, transfer_size, ftdi_write_bulk_callback, port); status = usb_submit_urb(urb, GFP_ATOMIC); if (status) { dev_err(&port->dev, "%s - failed submitting write urb, error %d\n", __func__, status); count = status; goto error; } else { spin_lock_irqsave(&priv->tx_lock, flags); priv->tx_outstanding_bytes += count; priv->tx_bytes += count; spin_unlock_irqrestore(&priv->tx_lock, flags); } /* we are done with this urb, so let the host driver * really free it when it is finished with it */ usb_free_urb(urb); dbg("%s write returning: %d", __func__, count); return count; error: usb_free_urb(urb); error_no_urb: kfree(buffer); error_no_buffer: spin_lock_irqsave(&priv->tx_lock, flags); priv->tx_outstanding_urbs--; spin_unlock_irqrestore(&priv->tx_lock, flags); return count; } /* ftdi_write */ /* This function may get called when the device is closed */ static void ftdi_write_bulk_callback(struct urb *urb) { unsigned long flags; struct usb_serial_port *port = urb->context; struct ftdi_private *priv; int data_offset; /* will be 1 for the SIO and 0 otherwise */ unsigned long countback; int status = urb->status; /* free up the transfer buffer, as usb_free_urb() does not do this */ kfree(urb->transfer_buffer); dbg("%s - port %d", __func__, port->number); priv = usb_get_serial_port_data(port); if (!priv) { dbg("%s - bad port private data pointer - exiting", __func__); return; } /* account for transferred data */ countback = urb->transfer_buffer_length; data_offset = priv->write_offset; if (data_offset > 0) { /* Subtract the control bytes */ countback -= (data_offset * DIV_ROUND_UP(countback, priv->max_packet_size)); } spin_lock_irqsave(&priv->tx_lock, flags); --priv->tx_outstanding_urbs; priv->tx_outstanding_bytes -= countback; spin_unlock_irqrestore(&priv->tx_lock, flags); if (status) { dbg("nonzero write bulk status received: %d", status); } usb_serial_port_softint(port); } /* ftdi_write_bulk_callback */ static int ftdi_write_room(struct tty_struct *tty) { struct usb_serial_port *port = tty->driver_data; struct ftdi_private *priv = usb_get_serial_port_data(port); int room; unsigned long flags; dbg("%s - port %d", __func__, port->number); spin_lock_irqsave(&priv->tx_lock, flags); if (priv->tx_outstanding_urbs < URB_UPPER_LIMIT) { /* * We really can take anything the user throws at us * but let's pick a nice big number to tell the tty * layer that we have lots of free space */ room = 2048; } else { room = 0; } spin_unlock_irqrestore(&priv->tx_lock, flags); return room; } static int ftdi_chars_in_buffer(struct tty_struct *tty) { struct usb_serial_port *port = tty->driver_data; struct ftdi_private *priv = usb_get_serial_port_data(port); int buffered; unsigned long flags; dbg("%s - port %d", __func__, port->number); spin_lock_irqsave(&priv->tx_lock, flags); buffered = (int)priv->tx_outstanding_bytes; spin_unlock_irqrestore(&priv->tx_lock, flags); if (buffered < 0) { dev_err(&port->dev, "%s outstanding tx bytes is negative!\n", __func__); buffered = 0; } return buffered; } static int ftdi_process_packet(struct tty_struct *tty, struct usb_serial_port *port, struct ftdi_private *priv, char *packet, int len) { int i; char status; char flag; char *ch; dbg("%s - port %d", __func__, port->number); if (len < 2) { dbg("malformed packet"); return 0; } /* Compare new line status to the old one, signal if different/ N.B. packet may be processed more than once, but differences are only processed once. */ status = packet[0] & FTDI_STATUS_B0_MASK; if (status != priv->prev_status) { priv->diff_status |= status ^ priv->prev_status; wake_up_interruptible(&priv->delta_msr_wait); priv->prev_status = status; } /* * Although the device uses a bitmask and hence can have multiple * errors on a packet - the order here sets the priority the error is * returned to the tty layer. */ flag = TTY_NORMAL; if (packet[1] & FTDI_RS_OE) { flag = TTY_OVERRUN; dbg("OVERRRUN error"); } if (packet[1] & FTDI_RS_BI) { flag = TTY_BREAK; dbg("BREAK received"); usb_serial_handle_break(port); } if (packet[1] & FTDI_RS_PE) { flag = TTY_PARITY; dbg("PARITY error"); } if (packet[1] & FTDI_RS_FE) { flag = TTY_FRAME; dbg("FRAMING error"); } len -= 2; if (!len) return 0; /* status only */ ch = packet + 2; if (!(port->console && port->sysrq) && flag == TTY_NORMAL) tty_insert_flip_string(tty, ch, len); else { for (i = 0; i < len; i++, ch++) { if (!usb_serial_handle_sysrq_char(tty, port, *ch)) tty_insert_flip_char(tty, *ch, flag); } } return len; } static void ftdi_process_read(struct usb_serial_port *port) { struct urb *urb = port->read_urb; struct tty_struct *tty; struct ftdi_private *priv = usb_get_serial_port_data(port); char *data = (char *)urb->transfer_buffer; int i; int len; int count = 0; tty = tty_port_tty_get(&port->port); if (!tty) return; for (i = 0; i < urb->actual_length; i += priv->max_packet_size) { len = min_t(int, urb->actual_length - i, priv->max_packet_size); count += ftdi_process_packet(tty, port, priv, &data[i], len); } if (count) tty_flip_buffer_push(tty); tty_kref_put(tty); } static void ftdi_read_bulk_callback(struct urb *urb) { struct usb_serial_port *port = urb->context; unsigned long flags; dbg("%s - port %d", __func__, port->number); if (urb->status) { dbg("%s - nonzero read bulk status received: %d", __func__, urb->status); return; } usb_serial_debug_data(debug, &port->dev, __func__, urb->actual_length, urb->transfer_buffer); ftdi_process_read(port); spin_lock_irqsave(&port->lock, flags); port->throttled = port->throttle_req; if (!port->throttled) { spin_unlock_irqrestore(&port->lock, flags); ftdi_submit_read_urb(port, GFP_ATOMIC); } else spin_unlock_irqrestore(&port->lock, flags); } static void ftdi_break_ctl(struct tty_struct *tty, int break_state) { struct usb_serial_port *port = tty->driver_data; struct ftdi_private *priv = usb_get_serial_port_data(port); __u16 urb_value = 0; char buf[1]; /* break_state = -1 to turn on break, and 0 to turn off break */ /* see drivers/char/tty_io.c to see it used */ /* last_set_data_urb_value NEVER has the break bit set in it */ if (break_state) urb_value = priv->last_set_data_urb_value | FTDI_SIO_SET_BREAK; else urb_value = priv->last_set_data_urb_value; if (usb_control_msg(port->serial->dev, usb_sndctrlpipe(port->serial->dev, 0), FTDI_SIO_SET_DATA_REQUEST, FTDI_SIO_SET_DATA_REQUEST_TYPE, urb_value , priv->interface, buf, 0, WDR_TIMEOUT) < 0) { dev_err(&port->dev, "%s FAILED to enable/disable break state " "(state was %d)\n", __func__, break_state); } dbg("%s break state is %d - urb is %d", __func__, break_state, urb_value); } /* old_termios contains the original termios settings and tty->termios contains * the new setting to be used * WARNING: set_termios calls this with old_termios in kernel space */ static void ftdi_set_termios(struct tty_struct *tty, struct usb_serial_port *port, struct ktermios *old_termios) { /* ftdi_termios */ struct usb_device *dev = port->serial->dev; struct ftdi_private *priv = usb_get_serial_port_data(port); struct ktermios *termios = tty->termios; unsigned int cflag = termios->c_cflag; __u16 urb_value; /* will hold the new flags */ char buf[1]; /* Perhaps I should dynamically alloc this? */ /* Added for xon/xoff support */ unsigned int iflag = termios->c_iflag; unsigned char vstop; unsigned char vstart; dbg("%s", __func__); /* Force baud rate if this device requires it, unless it is set to B0. */ if (priv->force_baud && ((termios->c_cflag & CBAUD) != B0)) { dbg("%s: forcing baud rate for this device", __func__); tty_encode_baud_rate(tty, priv->force_baud, priv->force_baud); } /* Force RTS-CTS if this device requires it. */ if (priv->force_rtscts) { dbg("%s: forcing rtscts for this device", __func__); termios->c_cflag |= CRTSCTS; } cflag = termios->c_cflag; if (old_termios->c_cflag == termios->c_cflag && old_termios->c_ispeed == termios->c_ispeed && old_termios->c_ospeed == termios->c_ospeed) goto no_c_cflag_changes; /* NOTE These routines can get interrupted by ftdi_sio_read_bulk_callback - need to examine what this means - don't see any problems yet */ if ((old_termios->c_cflag & (CSIZE|PARODD|PARENB|CMSPAR|CSTOPB)) == (termios->c_cflag & (CSIZE|PARODD|PARENB|CMSPAR|CSTOPB))) goto no_data_parity_stop_changes; /* Set number of data bits, parity, stop bits */ termios->c_cflag &= ~CMSPAR; urb_value = 0; urb_value |= (cflag & CSTOPB ? FTDI_SIO_SET_DATA_STOP_BITS_2 : FTDI_SIO_SET_DATA_STOP_BITS_1); urb_value |= (cflag & PARENB ? (cflag & PARODD ? FTDI_SIO_SET_DATA_PARITY_ODD : FTDI_SIO_SET_DATA_PARITY_EVEN) : FTDI_SIO_SET_DATA_PARITY_NONE); if (cflag & CSIZE) { switch (cflag & CSIZE) { case CS5: urb_value |= 5; dbg("Setting CS5"); break; case CS6: urb_value |= 6; dbg("Setting CS6"); break; case CS7: urb_value |= 7; dbg("Setting CS7"); break; case CS8: urb_value |= 8; dbg("Setting CS8"); break; default: dev_err(&port->dev, "CSIZE was set but not CS5-CS8\n"); } } /* This is needed by the break command since it uses the same command - but is or'ed with this value */ priv->last_set_data_urb_value = urb_value; if (usb_control_msg(dev, usb_sndctrlpipe(dev, 0), FTDI_SIO_SET_DATA_REQUEST, FTDI_SIO_SET_DATA_REQUEST_TYPE, urb_value , priv->interface, buf, 0, WDR_SHORT_TIMEOUT) < 0) { dev_err(&port->dev, "%s FAILED to set " "databits/stopbits/parity\n", __func__); } /* Now do the baudrate */ no_data_parity_stop_changes: if ((cflag & CBAUD) == B0) { /* Disable flow control */ if (usb_control_msg(dev, usb_sndctrlpipe(dev, 0), FTDI_SIO_SET_FLOW_CTRL_REQUEST, FTDI_SIO_SET_FLOW_CTRL_REQUEST_TYPE, 0, priv->interface, buf, 0, WDR_TIMEOUT) < 0) { dev_err(&port->dev, "%s error from disable flowcontrol urb\n", __func__); } /* Drop RTS and DTR */ clear_mctrl(port, TIOCM_DTR | TIOCM_RTS); } else { /* set the baudrate determined before */ if (change_speed(tty, port)) dev_err(&port->dev, "%s urb failed to set baudrate\n", __func__); /* Ensure RTS and DTR are raised when baudrate changed from 0 */ if (!old_termios || (old_termios->c_cflag & CBAUD) == B0) set_mctrl(port, TIOCM_DTR | TIOCM_RTS); } /* Set flow control */ /* Note device also supports DTR/CD (ugh) and Xon/Xoff in hardware */ no_c_cflag_changes: if (cflag & CRTSCTS) { dbg("%s Setting to CRTSCTS flow control", __func__); if (usb_control_msg(dev, usb_sndctrlpipe(dev, 0), FTDI_SIO_SET_FLOW_CTRL_REQUEST, FTDI_SIO_SET_FLOW_CTRL_REQUEST_TYPE, 0 , (FTDI_SIO_RTS_CTS_HS | priv->interface), buf, 0, WDR_TIMEOUT) < 0) { dev_err(&port->dev, "urb failed to set to rts/cts flow control\n"); } } else { /* * Xon/Xoff code * * Check the IXOFF status in the iflag component of the * termios structure. If IXOFF is not set, the pre-xon/xoff * code is executed. */ if (iflag & IXOFF) { dbg("%s request to enable xonxoff iflag=%04x", __func__, iflag); /* Try to enable the XON/XOFF on the ftdi_sio * Set the vstart and vstop -- could have been done up * above where a lot of other dereferencing is done but * that would be very inefficient as vstart and vstop * are not always needed. */ vstart = termios->c_cc[VSTART]; vstop = termios->c_cc[VSTOP]; urb_value = (vstop << 8) | (vstart); if (usb_control_msg(dev, usb_sndctrlpipe(dev, 0), FTDI_SIO_SET_FLOW_CTRL_REQUEST, FTDI_SIO_SET_FLOW_CTRL_REQUEST_TYPE, urb_value , (FTDI_SIO_XON_XOFF_HS | priv->interface), buf, 0, WDR_TIMEOUT) < 0) { dev_err(&port->dev, "urb failed to set to " "xon/xoff flow control\n"); } } else { /* else clause to only run if cflag ! CRTSCTS and iflag * ! XOFF. CHECKME Assuming XON/XOFF handled by tty * stack - not by device */ dbg("%s Turning off hardware flow control", __func__); if (usb_control_msg(dev, usb_sndctrlpipe(dev, 0), FTDI_SIO_SET_FLOW_CTRL_REQUEST, FTDI_SIO_SET_FLOW_CTRL_REQUEST_TYPE, 0, priv->interface, buf, 0, WDR_TIMEOUT) < 0) { dev_err(&port->dev, "urb failed to clear flow control\n"); } } } return; } static int ftdi_tiocmget(struct tty_struct *tty, struct file *file) { struct usb_serial_port *port = tty->driver_data; struct ftdi_private *priv = usb_get_serial_port_data(port); unsigned char buf[2]; int ret; dbg("%s TIOCMGET", __func__); switch (priv->chip_type) { case SIO: /* Request the status from the device */ ret = usb_control_msg(port->serial->dev, usb_rcvctrlpipe(port->serial->dev, 0), FTDI_SIO_GET_MODEM_STATUS_REQUEST, FTDI_SIO_GET_MODEM_STATUS_REQUEST_TYPE, 0, 0, buf, 1, WDR_TIMEOUT); if (ret < 0) return ret; break; case FT8U232AM: case FT232BM: case FT2232C: case FT232RL: case FT2232H: case FT4232H: /* the 8U232AM returns a two byte value (the sio is a 1 byte value) - in the same format as the data returned from the in point */ ret = usb_control_msg(port->serial->dev, usb_rcvctrlpipe(port->serial->dev, 0), FTDI_SIO_GET_MODEM_STATUS_REQUEST, FTDI_SIO_GET_MODEM_STATUS_REQUEST_TYPE, 0, priv->interface, buf, 2, WDR_TIMEOUT); if (ret < 0) return ret; break; default: return -EFAULT; } return (buf[0] & FTDI_SIO_DSR_MASK ? TIOCM_DSR : 0) | (buf[0] & FTDI_SIO_CTS_MASK ? TIOCM_CTS : 0) | (buf[0] & FTDI_SIO_RI_MASK ? TIOCM_RI : 0) | (buf[0] & FTDI_SIO_RLSD_MASK ? TIOCM_CD : 0) | priv->last_dtr_rts; } static int ftdi_tiocmset(struct tty_struct *tty, struct file *file, unsigned int set, unsigned int clear) { struct usb_serial_port *port = tty->driver_data; dbg("%s TIOCMSET", __func__); return update_mctrl(port, set, clear); } static int ftdi_ioctl(struct tty_struct *tty, struct file *file, unsigned int cmd, unsigned long arg) { struct usb_serial_port *port = tty->driver_data; struct ftdi_private *priv = usb_get_serial_port_data(port); dbg("%s cmd 0x%04x", __func__, cmd); /* Based on code from acm.c and others */ switch (cmd) { case TIOCGSERIAL: /* gets serial port data */ return get_serial_info(port, (struct serial_struct __user *) arg); case TIOCSSERIAL: /* sets serial port data */ return set_serial_info(tty, port, (struct serial_struct __user *) arg); /* * Wait for any of the 4 modem inputs (DCD,RI,DSR,CTS) to change * - mask passed in arg for lines of interest * (use |'ed TIOCM_RNG/DSR/CD/CTS for masking) * Caller should use TIOCGICOUNT to see which one it was. * * This code is borrowed from linux/drivers/char/serial.c */ case TIOCMIWAIT: while (priv != NULL) { interruptible_sleep_on(&priv->delta_msr_wait); /* see if a signal did it */ if (signal_pending(current)) return -ERESTARTSYS; else { char diff = priv->diff_status; if (diff == 0) return -EIO; /* no change => error */ /* Consume all events */ priv->diff_status = 0; /* Return 0 if caller wanted to know about these bits */ if (((arg & TIOCM_RNG) && (diff & FTDI_RS0_RI)) || ((arg & TIOCM_DSR) && (diff & FTDI_RS0_DSR)) || ((arg & TIOCM_CD) && (diff & FTDI_RS0_RLSD)) || ((arg & TIOCM_CTS) && (diff & FTDI_RS0_CTS))) { return 0; } /* * Otherwise caller can't care less about what * happened,and so we continue to wait for more * events. */ } } return 0; default: break; } /* This is not necessarily an error - turns out the higher layers * will do some ioctls themselves (see comment above) */ dbg("%s arg not supported - it was 0x%04x - check /usr/include/asm/ioctls.h", __func__, cmd); return -ENOIOCTLCMD; } static void ftdi_throttle(struct tty_struct *tty) { struct usb_serial_port *port = tty->driver_data; unsigned long flags; dbg("%s - port %d", __func__, port->number); spin_lock_irqsave(&port->lock, flags); port->throttle_req = 1; spin_unlock_irqrestore(&port->lock, flags); } void ftdi_unthrottle(struct tty_struct *tty) { struct usb_serial_port *port = tty->driver_data; int was_throttled; unsigned long flags; dbg("%s - port %d", __func__, port->number); spin_lock_irqsave(&port->lock, flags); was_throttled = port->throttled; port->throttled = port->throttle_req = 0; spin_unlock_irqrestore(&port->lock, flags); /* Resubmit urb if throttled and open. */ if (was_throttled && test_bit(ASYNCB_INITIALIZED, &port->port.flags)) ftdi_submit_read_urb(port, GFP_KERNEL); } static int __init ftdi_init(void) { int retval; dbg("%s", __func__); if (vendor > 0 && product > 0) { /* Add user specified VID/PID to reserved element of table. */ int i; for (i = 0; id_table_combined[i].idVendor; i++) ; id_table_combined[i].match_flags = USB_DEVICE_ID_MATCH_DEVICE; id_table_combined[i].idVendor = vendor; id_table_combined[i].idProduct = product; } retval = usb_serial_register(&ftdi_sio_device); if (retval) goto failed_sio_register; retval = usb_register(&ftdi_driver); if (retval) goto failed_usb_register; printk(KERN_INFO KBUILD_MODNAME ": " DRIVER_VERSION ":" DRIVER_DESC "\n"); return 0; failed_usb_register: usb_serial_deregister(&ftdi_sio_device); failed_sio_register: return retval; } static void __exit ftdi_exit(void) { dbg("%s", __func__); usb_deregister(&ftdi_driver); usb_serial_deregister(&ftdi_sio_device); } module_init(ftdi_init); module_exit(ftdi_exit); MODULE_AUTHOR(DRIVER_AUTHOR); MODULE_DESCRIPTION(DRIVER_DESC); MODULE_LICENSE("GPL"); module_param(debug, bool, S_IRUGO | S_IWUSR); MODULE_PARM_DESC(debug, "Debug enabled or not"); module_param(vendor, ushort, 0); MODULE_PARM_DESC(vendor, "User specified vendor ID (default=" __MODULE_STRING(FTDI_VID)")"); module_param(product, ushort, 0); MODULE_PARM_DESC(product, "User specified product ID"); module_param(ndi_latency_timer, int, S_IRUGO | S_IWUSR); MODULE_PARM_DESC(ndi_latency_timer, "NDI device latency timer override");