/*
 *  This program is free software; you can redistribute it and/or modify it
 *  under the terms of the GNU General Public License version 2 as published
 *  by the Free Software Foundation.
 *
 *  Copyright (C) 2010 John Crispin <blogic@openwrt.org>
 */

#include <linux/init.h>
#include <linux/io.h>
#include <linux/ioport.h>
#include <linux/pm.h>
#include <linux/export.h>
#include <linux/delay.h>
#include <linux/of_address.h>
#include <linux/of_platform.h>

#include <asm/reboot.h>

#include <lantiq_soc.h>

#include "../prom.h"

#define ltq_rcu_w32(x, y)	ltq_w32((x), ltq_rcu_membase + (y))
#define ltq_rcu_r32(x)		ltq_r32(ltq_rcu_membase + (x))

/* reset request register */
#define RCU_RST_REQ		0x0010
/* reset status register */
#define RCU_RST_STAT		0x0014
/* vr9 gphy registers */
#define RCU_GFS_ADD0_XRX200	0x0020
#define RCU_GFS_ADD1_XRX200	0x0068

/* reboot bit */
#define RCU_RD_GPHY0_XRX200	BIT(31)
#define RCU_RD_SRST		BIT(30)
#define RCU_RD_GPHY1_XRX200	BIT(29)

/* reset cause */
#define RCU_STAT_SHIFT		26
/* boot selection */
#define RCU_BOOT_SEL(x)		((x >> 18) & 0x7)
#define RCU_BOOT_SEL_XRX200(x)	(((x >> 17) & 0xf) | ((x >> 8) & 0x10))

/* remapped base addr of the reset control unit */
static void __iomem *ltq_rcu_membase;
static struct device_node *ltq_rcu_np;

/* This function is used by the watchdog driver */
int ltq_reset_cause(void)
{
	u32 val = ltq_rcu_r32(RCU_RST_STAT);
	return val >> RCU_STAT_SHIFT;
}
EXPORT_SYMBOL_GPL(ltq_reset_cause);

/* allow platform code to find out what source we booted from */
unsigned char ltq_boot_select(void)
{
	u32 val = ltq_rcu_r32(RCU_RST_STAT);

	if (of_device_is_compatible(ltq_rcu_np, "lantiq,rcu-xrx200"))
		return RCU_BOOT_SEL_XRX200(val);

	return RCU_BOOT_SEL(val);
}

/* reset / boot a gphy */
static struct ltq_xrx200_gphy_reset {
	u32 rd;
	u32 addr;
} xrx200_gphy[] = {
	{RCU_RD_GPHY0_XRX200, RCU_GFS_ADD0_XRX200},
	{RCU_RD_GPHY1_XRX200, RCU_GFS_ADD1_XRX200},
};

/* reset and boot a gphy. these phys only exist on xrx200 SoC */
int xrx200_gphy_boot(struct device *dev, unsigned int id, dma_addr_t dev_addr)
{
	struct clk *clk;

	if (!of_device_is_compatible(ltq_rcu_np, "lantiq,rcu-xrx200")) {
		dev_err(dev, "this SoC has no GPHY\n");
		return -EINVAL;
	}

	clk = clk_get_sys("1f203000.rcu", "gphy");
	if (IS_ERR(clk))
		return PTR_ERR(clk);

	clk_enable(clk);

	if (id > 1) {
		dev_err(dev, "%u is an invalid gphy id\n", id);
		return -EINVAL;
	}
	dev_info(dev, "booting GPHY%u firmware at %X\n", id, dev_addr);

	ltq_rcu_w32(ltq_rcu_r32(RCU_RST_REQ) | xrx200_gphy[id].rd,
			RCU_RST_REQ);
	ltq_rcu_w32(dev_addr, xrx200_gphy[id].addr);
	ltq_rcu_w32(ltq_rcu_r32(RCU_RST_REQ) & ~xrx200_gphy[id].rd,
			RCU_RST_REQ);
	return 0;
}

/* reset a io domain for u micro seconds */
void ltq_reset_once(unsigned int module, ulong u)
{
	ltq_rcu_w32(ltq_rcu_r32(RCU_RST_REQ) | module, RCU_RST_REQ);
	udelay(u);
	ltq_rcu_w32(ltq_rcu_r32(RCU_RST_REQ) & ~module, RCU_RST_REQ);
}

#if !defined(CONFIG_AR10) && !defined(CONFIG_VR9)
static void ltq_machine_restart(char *command)
{
	local_irq_disable();
	ltq_rcu_w32(ltq_rcu_r32(RCU_RST_REQ) | RCU_RD_SRST, RCU_RST_REQ);
	unreachable();
}

static void ltq_machine_halt(void)
{
	local_irq_disable();
	unreachable();
}

static void ltq_machine_power_off(void)
{
	local_irq_disable();
	unreachable();
}

static int __init mips_reboot_setup(void)
{
	struct resource res;

	ltq_rcu_np = of_find_compatible_node(NULL, NULL, "lantiq,rcu-xway");
	if (!ltq_rcu_np)
		ltq_rcu_np = of_find_compatible_node(NULL, NULL,
							"lantiq,rcu-xrx200");

	/* check if all the reset register range is available */
	if (!ltq_rcu_np)
		panic("Failed to load reset resources from devicetree");

	if (of_address_to_resource(ltq_rcu_np, 0, &res))
		panic("Failed to get rcu memory range");

	if (request_mem_region(res.start, resource_size(&res), res.name) < 0)
		pr_err("Failed to request rcu memory");

	ltq_rcu_membase = ioremap_nocache(res.start, resource_size(&res));
	if (!ltq_rcu_membase)
		panic("Failed to remap core memory");

	_machine_restart = ltq_machine_restart;
	_machine_halt = ltq_machine_halt;
	pm_power_off = ltq_machine_power_off;

	return 0;
}

arch_initcall(mips_reboot_setup);
#endif /* !CONFIG_AR10 */