--- zzzz-none-000/linux-3.10.107/include/linux/mmc/host.h	2017-06-27 09:49:32.000000000 +0000
+++ vr9-7490-729/linux-3.10.107/include/linux/mmc/host.h	2021-11-10 11:53:56.000000000 +0000
@@ -11,7 +11,6 @@
 #define LINUX_MMC_HOST_H
 
 #include <linux/leds.h>
-#include <linux/mutex.h>
 #include <linux/sched.h>
 #include <linux/device.h>
 #include <linux/fault-inject.h>
@@ -53,12 +52,12 @@
 #define MMC_TIMING_LEGACY	0
 #define MMC_TIMING_MMC_HS	1
 #define MMC_TIMING_SD_HS	2
-#define MMC_TIMING_UHS_SDR12	3
-#define MMC_TIMING_UHS_SDR25	4
-#define MMC_TIMING_UHS_SDR50	5
-#define MMC_TIMING_UHS_SDR104	6
-#define MMC_TIMING_UHS_DDR50	7
-#define MMC_TIMING_MMC_HS200	8
+#define MMC_TIMING_UHS_SDR12	MMC_TIMING_LEGACY
+#define MMC_TIMING_UHS_SDR25	MMC_TIMING_SD_HS
+#define MMC_TIMING_UHS_SDR50	3
+#define MMC_TIMING_UHS_SDR104	4
+#define MMC_TIMING_UHS_DDR50	5
+#define MMC_TIMING_MMC_HS200	6
 
 #define MMC_SDR_MODE		0
 #define MMC_1_2V_DDR_MODE	1
@@ -136,6 +135,7 @@
 
 	/* The tuning command opcode value is different for SD and eMMC cards */
 	int	(*execute_tuning)(struct mmc_host *host, u32 opcode);
+	void	(*enable_preset_value)(struct mmc_host *host, bool enable);
 	int	(*select_drive_strength)(unsigned int max_dtr, int host_drv, int card_drv);
 	void	(*hw_reset)(struct mmc_host *host);
 	void	(*card_event)(struct mmc_host *host);
@@ -254,9 +254,16 @@
 #define MMC_CAP_UHS_SDR50	(1 << 17)	/* Host supports UHS SDR50 mode */
 #define MMC_CAP_UHS_SDR104	(1 << 18)	/* Host supports UHS SDR104 mode */
 #define MMC_CAP_UHS_DDR50	(1 << 19)	/* Host supports UHS DDR50 mode */
+#define MMC_CAP_SET_XPC_330	(1 << 20)	/* Host supports >150mA current at 3.3V */
+#define MMC_CAP_SET_XPC_300	(1 << 21)	/* Host supports >150mA current at 3.0V */
+#define MMC_CAP_SET_XPC_180	(1 << 22)	/* Host supports >150mA current at 1.8V */
 #define MMC_CAP_DRIVER_TYPE_A	(1 << 23)	/* Host supports Driver Type A */
 #define MMC_CAP_DRIVER_TYPE_C	(1 << 24)	/* Host supports Driver Type C */
 #define MMC_CAP_DRIVER_TYPE_D	(1 << 25)	/* Host supports Driver Type D */
+#define MMC_CAP_MAX_CURRENT_200	(1 << 26)	/* Host max current limit is 200mA */
+#define MMC_CAP_MAX_CURRENT_400	(1 << 27)	/* Host max current limit is 400mA */
+#define MMC_CAP_MAX_CURRENT_600	(1 << 28)	/* Host max current limit is 600mA */
+#define MMC_CAP_MAX_CURRENT_800	(1 << 29)	/* Host max current limit is 800mA */
 #define MMC_CAP_CMD23		(1 << 30)	/* CMD23 supported. */
 #define MMC_CAP_HW_RESET	(1 << 31)	/* Hardware reset */
 
@@ -283,6 +290,10 @@
 #define MMC_CAP2_NO_PRESCAN_POWERUP (1 << 14)	/* Don't power up before scan */
 
 	mmc_pm_flag_t		pm_caps;	/* supported pm features */
+	unsigned int        power_notify_type;
+#define MMC_HOST_PW_NOTIFY_NONE		0
+#define MMC_HOST_PW_NOTIFY_SHORT	1
+#define MMC_HOST_PW_NOTIFY_LONG		2
 
 #ifdef CONFIG_MMC_CLKGATE
 	int			clk_requests;	/* internal reference counter */
@@ -342,7 +353,9 @@
 
 	mmc_pm_flag_t		pm_flags;	/* requested pm features */
 
+#ifdef CONFIG_LEDS_TRIGGERS
 	struct led_trigger	*led;		/* activity led */
+#endif
 
 #ifdef CONFIG_REGULATOR
 	bool			regulator_enabled; /* regulator state */