/* * see notice in hfc_multi.c */ #define DEBUG_HFCMULTI_FIFO 0x00010000 #define DEBUG_HFCMULTI_CRC 0x00020000 #define DEBUG_HFCMULTI_INIT 0x00040000 #define DEBUG_HFCMULTI_PLXSD 0x00080000 #define DEBUG_HFCMULTI_MODE 0x00100000 #define DEBUG_HFCMULTI_MSG 0x00200000 #define DEBUG_HFCMULTI_STATE 0x00400000 #define DEBUG_HFCMULTI_FILL 0x00800000 #define DEBUG_HFCMULTI_SYNC 0x01000000 #define DEBUG_HFCMULTI_DTMF 0x02000000 #define DEBUG_HFCMULTI_LOCK 0x80000000 #define PCI_ENA_REGIO 0x01 #define PCI_ENA_MEMIO 0x02 #define XHFC_IRQ 4 /* SIU_IRQ2 */ #define XHFC_MEMBASE 0xFE000000 #define XHFC_MEMSIZE 0x00001000 #define XHFC_OFFSET 0x00001000 #define PA_XHFC_A0 0x0020 /* PA10 */ #define PB_XHFC_IRQ1 0x00000100 /* PB23 */ #define PB_XHFC_IRQ2 0x00000200 /* PB22 */ #define PB_XHFC_IRQ3 0x00000400 /* PB21 */ #define PB_XHFC_IRQ4 0x00000800 /* PB20 */ /* * NOTE: some registers are assigned multiple times due to different modes * also registers are assigned differen for HFC-4s/8s and HFC-E1 */ /* #define MAX_FRAME_SIZE 2048 */ struct hfc_chan { struct dchannel *dch; /* link if channel is a D-channel */ struct bchannel *bch; /* link if channel is a B-channel */ int port; /* the interface port this */ /* channel is associated with */ int nt_timer; /* -1 if off, 0 if elapsed, >0 if running */ int los, ais, slip_tx, slip_rx, rdi; /* current alarms */ int jitter; u_long cfg; /* port configuration */ int sync; /* sync state (used by E1) */ u_int protocol; /* current protocol */ int slot_tx; /* current pcm slot */ int bank_tx; /* current pcm bank */ int slot_rx; int bank_rx; int conf; /* conference setting of TX slot */ int txpending; /* if there is currently data in */ /* the FIFO 0=no, 1=yes, 2=splloop */ int Zfill; /* rx-fifo level on last hfcmulti_tx */ int rx_off; /* set to turn fifo receive off */ int coeff_count; /* curren coeff block */ s32 *coeff; /* memory pointer to 8 coeff blocks */ }; struct hfcm_hw { u_char r_ctrl; u_char r_irq_ctrl; u_char r_cirm; u_char r_ram_sz; u_char r_pcm_md0; u_char r_irqmsk_misc; u_char r_dtmf; u_char r_st_sync; u_char r_sci_msk; u_char r_tx0, r_tx1; u_char a_st_ctrl0[8]; u_char r_bert_wd_md; timer_t timer; }; /* for each stack these flags are used (cfg) */ #define HFC_CFG_NONCAP_TX 1 /* S/T TX interface has less capacity */ #define HFC_CFG_DIS_ECHANNEL 2 /* disable E-channel processing */ #define HFC_CFG_REG_ECHANNEL 3 /* register E-channel */ #define HFC_CFG_OPTICAL 4 /* the E1 interface is optical */ #define HFC_CFG_REPORT_LOS 5 /* the card should report loss of signal */ #define HFC_CFG_REPORT_AIS 6 /* the card should report alarm ind. sign. */ #define HFC_CFG_REPORT_SLIP 7 /* the card should report bit slips */ #define HFC_CFG_REPORT_RDI 8 /* the card should report remote alarm */ #define HFC_CFG_DTMF 9 /* enable DTMF-detection */ #define HFC_CFG_CRC4 10 /* disable CRC-4 Multiframe mode, */ /* use double frame instead. */ #define HFC_TYPE_E1 1 /* controller is HFC-E1 */ #define HFC_TYPE_4S 4 /* controller is HFC-4S */ #define HFC_TYPE_8S 8 /* controller is HFC-8S */ #define HFC_TYPE_XHFC 5 /* controller is XHFC */ #define HFC_CHIP_EXRAM_128 0 /* external ram 128k */ #define HFC_CHIP_EXRAM_512 1 /* external ram 256k */ #define HFC_CHIP_REVISION0 2 /* old fifo handling */ #define HFC_CHIP_PCM_SLAVE 3 /* PCM is slave */ #define HFC_CHIP_PCM_MASTER 4 /* PCM is master */ #define HFC_CHIP_RX_SYNC 5 /* disable pll sync for pcm */ #define HFC_CHIP_DTMF 6 /* DTMF decoding is enabled */ #define HFC_CHIP_CONF 7 /* conference handling is enabled */ #define HFC_CHIP_ULAW 8 /* ULAW mode */ #define HFC_CHIP_CLOCK2 9 /* double clock mode */ #define HFC_CHIP_E1CLOCK_GET 10 /* always get clock from E1 interface */ #define HFC_CHIP_E1CLOCK_PUT 11 /* always put clock from E1 interface */ #define HFC_CHIP_WATCHDOG 12 /* whether we should send signals */ /* to the watchdog */ #define HFC_CHIP_B410P 13 /* whether we have a b410p with echocan in */ /* hw */ #define HFC_CHIP_PLXSD 14 /* whether we have a Speech-Design PLX */ #define HFC_CHIP_EMBSD 15 /* whether we have a SD Embedded board */ #define HFC_IO_MODE_PCIMEM 0x00 /* normal memory mapped IO */ #define HFC_IO_MODE_REGIO 0x01 /* PCI io access */ #define HFC_IO_MODE_PLXSD 0x02 /* access HFC via PLX9030 */ #define HFC_IO_MODE_EMBSD 0x03 /* direct access */ /* table entry in the PCI devices list */ struct hm_map { char *vendor_name; char *card_name; int type; int ports; int clock2; int leds; int opticalsupport; int dip_type; int io_mode; int irq; }; struct hfc_multi { struct list_head list; struct hm_map *mtyp; int id; int pcm; /* id of pcm bus */ int ctype; /* controller type */ int ports; u_int irq; /* irq used by card */ u_int irqcnt; struct pci_dev *pci_dev; int io_mode; /* selects mode */ #ifdef HFC_REGISTER_DEBUG void (*HFC_outb)(struct hfc_multi *hc, u_char reg, u_char val, const char *function, int line); void (*HFC_outb_nodebug)(struct hfc_multi *hc, u_char reg, u_char val, const char *function, int line); u_char (*HFC_inb)(struct hfc_multi *hc, u_char reg, const char *function, int line); u_char (*HFC_inb_nodebug)(struct hfc_multi *hc, u_char reg, const char *function, int line); u_short (*HFC_inw)(struct hfc_multi *hc, u_char reg, const char *function, int line); u_short (*HFC_inw_nodebug)(struct hfc_multi *hc, u_char reg, const char *function, int line); void (*HFC_wait)(struct hfc_multi *hc, const char *function, int line); void (*HFC_wait_nodebug)(struct hfc_multi *hc, const char *function, int line); #else void (*HFC_outb)(struct hfc_multi *hc, u_char reg, u_char val); void (*HFC_outb_nodebug)(struct hfc_multi *hc, u_char reg, u_char val); u_char (*HFC_inb)(struct hfc_multi *hc, u_char reg); u_char (*HFC_inb_nodebug)(struct hfc_multi *hc, u_char reg); u_short (*HFC_inw)(struct hfc_multi *hc, u_char reg); u_short (*HFC_inw_nodebug)(struct hfc_multi *hc, u_char reg); void (*HFC_wait)(struct hfc_multi *hc); void (*HFC_wait_nodebug)(struct hfc_multi *hc); #endif void (*read_fifo)(struct hfc_multi *hc, u_char *data, int len); void (*write_fifo)(struct hfc_multi *hc, u_char *data, int len); u_long pci_origmembase, plx_origmembase; void __iomem *pci_membase; /* PCI memory */ void __iomem *plx_membase; /* PLX memory */ u_long xhfc_origmembase; u_char *xhfc_membase; u_long *xhfc_memaddr, *xhfc_memdata; #ifdef CONFIG_MISDN_HFCMULTI_8xx struct immap *immap; #endif u_long pb_irqmsk; /* Portbit mask to check the IRQ line */ u_long pci_iobase; /* PCI IO */ struct hfcm_hw hw; /* remember data of write-only-registers */ u_long chip; /* chip configuration */ int masterclk; /* port that provides master clock -1=off */ unsigned char silence;/* silence byte */ unsigned char silence_data[128];/* silence block */ int dtmf; /* flag that dtmf is currently in process */ int Flen; /* F-buffer size */ int Zlen; /* Z-buffer size (must be int for calculation)*/ int max_trans; /* maximum transparent fifo fill */ int Zmin; /* Z-buffer offset */ int DTMFbase; /* base address of DTMF coefficients */ u_int slots; /* number of PCM slots */ u_int leds; /* type of leds */ u_long ledstate; /* save last state of leds */ int opticalsupport; /* has the e1 board */ /* an optical Interface */ u_int bmask[32]; /* bitmask of bchannels for port */ u_char dnum[32]; /* array of used dchannel numbers for port */ u_char created[32]; /* what port is created */ u_int activity_tx; /* if there is data TX / RX */ u_int activity_rx; /* bitmask according to port number */ /* (will be cleared after */ /* showing led-states) */ u_int flash[8]; /* counter for flashing 8 leds on activity */ u_long wdcount; /* every 500 ms we need to */ /* send the watchdog a signal */ u_char wdbyte; /* watchdog toggle byte */ int e1_state; /* keep track of last state */ int e1_getclock; /* if sync is retrieved from interface */ int syncronized; /* keep track of existing sync interface */ int e1_resync; /* resync jobs */ spinlock_t lock; /* the lock */ struct mISDNclock *iclock; /* isdn clock support */ int iclock_on; /* * the channel index is counted from 0, regardless where the channel * is located on the hfc-channel. * the bch->channel is equvalent to the hfc-channel */ struct hfc_chan chan[32]; signed char slot_owner[256]; /* owner channel of slot */ }; /* PLX GPIOs */ #define PLX_GPIO4_DIR_BIT 13 #define PLX_GPIO4_BIT 14 #define PLX_GPIO5_DIR_BIT 16 #define PLX_GPIO5_BIT 17 #define PLX_GPIO6_DIR_BIT 19 #define PLX_GPIO6_BIT 20 #define PLX_GPIO7_DIR_BIT 22 #define PLX_GPIO7_BIT 23 #define PLX_GPIO8_DIR_BIT 25 #define PLX_GPIO8_BIT 26 #define PLX_GPIO4 (1 << PLX_GPIO4_BIT) #define PLX_GPIO5 (1 << PLX_GPIO5_BIT) #define PLX_GPIO6 (1 << PLX_GPIO6_BIT) #define PLX_GPIO7 (1 << PLX_GPIO7_BIT) #define PLX_GPIO8 (1 << PLX_GPIO8_BIT) #define PLX_GPIO4_DIR (1 << PLX_GPIO4_DIR_BIT) #define PLX_GPIO5_DIR (1 << PLX_GPIO5_DIR_BIT) #define PLX_GPIO6_DIR (1 << PLX_GPIO6_DIR_BIT) #define PLX_GPIO7_DIR (1 << PLX_GPIO7_DIR_BIT) #define PLX_GPIO8_DIR (1 << PLX_GPIO8_DIR_BIT) #define PLX_TERM_ON PLX_GPIO7 #define PLX_SLAVE_EN_N PLX_GPIO5 #define PLX_MASTER_EN PLX_GPIO6 #define PLX_SYNC_O_EN PLX_GPIO4 #define PLX_DSP_RES_N PLX_GPIO8 /* GPIO4..8 Enable & Set to OUT, SLAVE_EN_N = 1 */ #define PLX_GPIOC_INIT (PLX_GPIO4_DIR | PLX_GPIO5_DIR | PLX_GPIO6_DIR \ | PLX_GPIO7_DIR | PLX_GPIO8_DIR | PLX_SLAVE_EN_N) /* PLX Interrupt Control/STATUS */ #define PLX_INTCSR_LINTI1_ENABLE 0x01 #define PLX_INTCSR_LINTI1_STATUS 0x04 #define PLX_INTCSR_LINTI2_ENABLE 0x08 #define PLX_INTCSR_LINTI2_STATUS 0x20 #define PLX_INTCSR_PCIINT_ENABLE 0x40 /* PLX Registers */ #define PLX_INTCSR 0x4c #define PLX_CNTRL 0x50 #define PLX_GPIOC 0x54 /* * REGISTER SETTING FOR HFC-4S/8S AND HFC-E1 */ /* write only registers */ #define R_CIRM 0x00 #define R_CTRL 0x01 #define R_BRG_PCM_CFG 0x02 #define R_RAM_ADDR0 0x08 #define R_RAM_ADDR1 0x09 #define R_RAM_ADDR2 0x0A #define R_FIRST_FIFO 0x0B #define R_RAM_SZ 0x0C #define R_FIFO_MD 0x0D #define R_INC_RES_FIFO 0x0E #define R_FSM_IDX 0x0F #define R_FIFO 0x0F #define R_SLOT 0x10 #define R_IRQMSK_MISC 0x11 #define R_SCI_MSK 0x12 #define R_IRQ_CTRL 0x13 #define R_PCM_MD0 0x14 #define R_PCM_MD1 0x15 #define R_PCM_MD2 0x15 #define R_SH0H 0x15 #define R_SH1H 0x15 #define R_SH0L 0x15 #define R_SH1L 0x15 #define R_SL_SEL0 0x15 #define R_SL_SEL1 0x15 #define R_SL_SEL2 0x15 #define R_SL_SEL3 0x15 #define R_SL_SEL4 0x15 #define R_SL_SEL5 0x15 #define R_SL_SEL6 0x15 #define R_SL_SEL7 0x15 #define R_ST_SEL 0x16 #define R_ST_SYNC 0x17 #define R_CONF_EN 0x18 #define R_TI_WD 0x1A #define R_BERT_WD_MD 0x1B #define R_DTMF 0x1C #define R_DTMF_N 0x1D #define R_E1_WR_STA 0x20 #define R_E1_RD_STA 0x20 #define R_LOS0 0x22 #define R_LOS1 0x23 #define R_RX0 0x24 #define R_RX_FR0 0x25 #define R_RX_FR1 0x26 #define R_TX0 0x28 #define R_TX1 0x29 #define R_TX_FR0 0x2C #define R_TX_FR1 0x2D #define R_TX_FR2 0x2E #define R_JATT_ATT 0x2F /* undocumented */ #define A_ST_RD_STATE 0x30 #define A_ST_WR_STATE 0x30 #define R_RX_OFF 0x30 #define A_ST_CTRL0 0x31 #define R_SYNC_OUT 0x31 #define A_ST_CTRL1 0x32 #define A_ST_CTRL2 0x33 #define A_ST_SQ_WR 0x34 #define R_TX_OFF 0x34 #define R_SYNC_CTRL 0x35 #define A_ST_CLK_DLY 0x37 #define R_PWM0 0x38 #define R_PWM1 0x39 #define A_ST_B1_TX 0x3C #define A_ST_B2_TX 0x3D #define A_ST_D_TX 0x3E #define R_GPIO_OUT0 0x40 #define R_GPIO_OUT1 0x41 #define R_GPIO_EN0 0x42 #define R_GPIO_EN1 0x43 #define R_GPIO_SEL 0x44 #define R_BRG_CTRL 0x45 #define R_PWM_MD 0x46 #define R_BRG_MD 0x47 #define R_BRG_TIM0 0x48 #define R_BRG_TIM1 0x49 #define R_BRG_TIM2 0x4A #define R_BRG_TIM3 0x4B #define R_BRG_TIM_SEL01 0x4C #define R_BRG_TIM_SEL23 0x4D #define R_BRG_TIM_SEL45 0x4E #define R_BRG_TIM_SEL67 0x4F #define A_SL_CFG 0xD0 #define A_CONF 0xD1 #define A_CH_MSK 0xF4 #define A_CON_HDLC 0xFA #define A_SUBCH_CFG 0xFB #define A_CHANNEL 0xFC #define A_FIFO_SEQ 0xFD #define A_IRQ_MSK 0xFF /* read only registers */ #define A_Z12 0x04 #define A_Z1L 0x04 #define A_Z1 0x04 #define A_Z1H 0x05 #define A_Z2L 0x06 #define A_Z2 0x06 #define A_Z2H 0x07 #define A_F1 0x0C #define A_F12 0x0C #define A_F2 0x0D #define R_IRQ_OVIEW 0x10 #define R_IRQ_MISC 0x11 #define R_IRQ_STATECH 0x12 #define R_CONF_OFLOW 0x14 #define R_RAM_USE 0x15 #define R_CHIP_ID 0x16 #define R_BERT_STA 0x17 #define R_F0_CNTL 0x18 #define R_F0_CNTH 0x19 #define R_BERT_EC 0x1A #define R_BERT_ECL 0x1A #define R_BERT_ECH 0x1B #define R_STATUS 0x1C #define R_CHIP_RV 0x1F #define R_STATE 0x20 #define R_SYNC_STA 0x24 #define R_RX_SL0_0 0x25 #define R_RX_SL0_1 0x26 #define R_RX_SL0_2 0x27 #define R_JATT_DIR 0x2b /* undocumented */ #define R_SLIP 0x2c #define A_ST_RD_STA 0x30 #define R_FAS_EC 0x30 #define R_FAS_ECL 0x30 #define R_FAS_ECH 0x31 #define R_VIO_EC 0x32 #define R_VIO_ECL 0x32 #define R_VIO_ECH 0x33 #define A_ST_SQ_RD 0x34 #define R_CRC_EC 0x34 #define R_CRC_ECL 0x34 #define R_CRC_ECH 0x35 #define R_E_EC 0x36 #define R_E_ECL 0x36 #define R_E_ECH 0x37 #define R_SA6_SA13_EC 0x38 #define R_SA6_SA13_ECL 0x38 #define R_SA6_SA13_ECH 0x39 #define R_SA6_SA23_EC 0x3A #define R_SA6_SA23_ECL 0x3A #define R_SA6_SA23_ECH 0x3B #define A_ST_B1_RX 0x3C #define A_ST_B2_RX 0x3D #define A_ST_D_RX 0x3E #define A_ST_E_RX 0x3F #define R_GPIO_IN0 0x40 #define R_GPIO_IN1 0x41 #define R_GPI_IN0 0x44 #define R_GPI_IN1 0x45 #define R_GPI_IN2 0x46 #define R_GPI_IN3 0x47 #define R_INT_DATA 0x88 #define R_IRQ_FIFO_BL0 0xC8 #define R_IRQ_FIFO_BL1 0xC9 #define R_IRQ_FIFO_BL2 0xCA #define R_IRQ_FIFO_BL3 0xCB #define R_IRQ_FIFO_BL4 0xCC #define R_IRQ_FIFO_BL5 0xCD #define R_IRQ_FIFO_BL6 0xCE #define R_IRQ_FIFO_BL7 0xCF /* read and write registers */ #define A_FIFO_DATA0 0x80 #define A_FIFO_DATA1 0x80 #define A_FIFO_DATA2 0x80 #define A_FIFO_DATA0_NOINC 0x84 #define A_FIFO_DATA1_NOINC 0x84 #define A_FIFO_DATA2_NOINC 0x84 #define R_RAM_DATA 0xC0 /* * BIT SETTING FOR HFC-4S/8S AND HFC-E1 */ /* chapter 2: universal bus interface */ /* R_CIRM */ #define V_IRQ_SEL 0x01 #define V_SRES 0x08 #define V_HFCRES 0x10 #define V_PCMRES 0x20 #define V_STRES 0x40 #define V_ETRES 0x40 #define V_RLD_EPR 0x80 /* R_CTRL */ #define V_FIFO_LPRIO 0x02 #define V_SLOW_RD 0x04 #define V_EXT_RAM 0x08 #define V_CLK_OFF 0x20 #define V_ST_CLK 0x40 /* R_RAM_ADDR0 */ #define V_RAM_ADDR2 0x01 #define V_ADDR_RES 0x40 #define V_ADDR_INC 0x80 /* R_RAM_SZ */ #define V_RAM_SZ 0x01 #define V_PWM0_16KHZ 0x10 #define V_PWM1_16KHZ 0x20 #define V_FZ_MD 0x80 /* R_CHIP_ID */ #define V_PNP_IRQ 0x01 #define V_CHIP_ID 0x10 /* chapter 3: data flow */ /* R_FIRST_FIFO */ #define V_FIRST_FIRO_DIR 0x01 #define V_FIRST_FIFO_NUM 0x02 /* R_FIFO_MD */ #define V_FIFO_MD 0x01 #define V_CSM_MD 0x04 #define V_FSM_MD 0x08 #define V_FIFO_SZ 0x10 /* R_FIFO */ #define V_FIFO_DIR 0x01 #define V_FIFO_NUM 0x02 #define V_REV 0x80 /* R_SLOT */ #define V_SL_DIR 0x01 #define V_SL_NUM 0x02 /* A_SL_CFG */ #define V_CH_DIR 0x01 #define V_CH_SEL 0x02 #define V_ROUTING 0x40 /* A_CON_HDLC */ #define V_IFF 0x01 #define V_HDLC_TRP 0x02 #define V_TRP_IRQ 0x04 #define V_DATA_FLOW 0x20 /* A_SUBCH_CFG */ #define V_BIT_CNT 0x01 #define V_START_BIT 0x08 #define V_LOOP_FIFO 0x40 #define V_INV_DATA 0x80 /* A_CHANNEL */ #define V_CH_DIR0 0x01 #define V_CH_NUM0 0x02 /* A_FIFO_SEQ */ #define V_NEXT_FIFO_DIR 0x01 #define V_NEXT_FIFO_NUM 0x02 #define V_SEQ_END 0x40 /* chapter 4: FIFO handling and HDLC controller */ /* R_INC_RES_FIFO */ #define V_INC_F 0x01 #define V_RES_F 0x02 #define V_RES_LOST 0x04 /* chapter 5: S/T interface */ /* R_SCI_MSK */ #define V_SCI_MSK_ST0 0x01 #define V_SCI_MSK_ST1 0x02 #define V_SCI_MSK_ST2 0x04 #define V_SCI_MSK_ST3 0x08 #define V_SCI_MSK_ST4 0x10 #define V_SCI_MSK_ST5 0x20 #define V_SCI_MSK_ST6 0x40 #define V_SCI_MSK_ST7 0x80 /* R_ST_SEL */ #define V_ST_SEL 0x01 #define V_MULT_ST 0x08 /* R_ST_SYNC */ #define V_SYNC_SEL 0x01 #define V_AUTO_SYNC 0x08 /* A_ST_WR_STA */ #define V_ST_SET_STA 0x01 #define V_ST_LD_STA 0x10 #define V_ST_ACT 0x20 #define V_SET_G2_G3 0x80 /* A_ST_CTRL0 */ #define V_B1_EN 0x01 #define V_B2_EN 0x02 #define V_ST_MD 0x04 #define V_D_PRIO 0x08 #define V_SQ_EN 0x10 #define V_96KHZ 0x20 #define V_TX_LI 0x40 #define V_ST_STOP 0x80 /* A_ST_CTRL1 */ #define V_G2_G3_EN 0x01 #define V_D_HI 0x04 #define V_E_IGNO 0x08 #define V_E_LO 0x10 #define V_B12_SWAP 0x80 /* A_ST_CTRL2 */ #define V_B1_RX_EN 0x01 #define V_B2_RX_EN 0x02 #define V_ST_TRIS 0x40 /* A_ST_CLK_DLY */ #define V_ST_CK_DLY 0x01 #define V_ST_SMPL 0x10 /* A_ST_D_TX */ #define V_ST_D_TX 0x40 /* R_IRQ_STATECH */ #define V_SCI_ST0 0x01 #define V_SCI_ST1 0x02 #define V_SCI_ST2 0x04 #define V_SCI_ST3 0x08 #define V_SCI_ST4 0x10 #define V_SCI_ST5 0x20 #define V_SCI_ST6 0x40 #define V_SCI_ST7 0x80 /* A_ST_RD_STA */ #define V_ST_STA 0x01 #define V_FR_SYNC_ST 0x10 #define V_TI2_EXP 0x20 #define V_INFO0 0x40 #define V_G2_G3 0x80 /* A_ST_SQ_RD */ #define V_ST_SQ 0x01 #define V_MF_RX_RDY 0x10 #define V_MF_TX_RDY 0x80 /* A_ST_D_RX */ #define V_ST_D_RX 0x40 /* A_ST_E_RX */ #define V_ST_E_RX 0x40 /* chapter 5: E1 interface */ /* R_E1_WR_STA */ /* R_E1_RD_STA */ #define V_E1_SET_STA 0x01 #define V_E1_LD_STA 0x10 /* R_RX0 */ #define V_RX_CODE 0x01 #define V_RX_FBAUD 0x04 #define V_RX_CMI 0x08 #define V_RX_INV_CMI 0x10 #define V_RX_INV_CLK 0x20 #define V_RX_INV_DATA 0x40 #define V_AIS_ITU 0x80 /* R_RX_FR0 */ #define V_NO_INSYNC 0x01 #define V_AUTO_RESYNC 0x02 #define V_AUTO_RECO 0x04 #define V_SWORD_COND 0x08 #define V_SYNC_LOSS 0x10 #define V_XCRC_SYNC 0x20 #define V_MF_RESYNC 0x40 #define V_RESYNC 0x80 /* R_RX_FR1 */ #define V_RX_MF 0x01 #define V_RX_MF_SYNC 0x02 #define V_RX_SL0_RAM 0x04 #define V_ERR_SIM 0x20 #define V_RES_NMF 0x40 /* R_TX0 */ #define V_TX_CODE 0x01 #define V_TX_FBAUD 0x04 #define V_TX_CMI_CODE 0x08 #define V_TX_INV_CMI_CODE 0x10 #define V_TX_INV_CLK 0x20 #define V_TX_INV_DATA 0x40 #define V_OUT_EN 0x80 /* R_TX1 */ #define V_INV_CLK 0x01 #define V_EXCHG_DATA_LI 0x02 #define V_AIS_OUT 0x04 #define V_ATX 0x20 #define V_NTRI 0x40 #define V_AUTO_ERR_RES 0x80 /* R_TX_FR0 */ #define V_TRP_FAS 0x01 #define V_TRP_NFAS 0x02 #define V_TRP_RAL 0x04 #define V_TRP_SA 0x08 /* R_TX_FR1 */ #define V_TX_FAS 0x01 #define V_TX_NFAS 0x02 #define V_TX_RAL 0x04 #define V_TX_SA 0x08 /* R_TX_FR2 */ #define V_TX_MF 0x01 #define V_TRP_SL0 0x02 #define V_TX_SL0_RAM 0x04 #define V_TX_E 0x10 #define V_NEG_E 0x20 #define V_XS12_ON 0x40 #define V_XS15_ON 0x80 /* R_RX_OFF */ #define V_RX_SZ 0x01 #define V_RX_INIT 0x04 /* R_SYNC_OUT */ #define V_SYNC_E1_RX 0x01 #define V_IPATS0 0x20 #define V_IPATS1 0x40 #define V_IPATS2 0x80 /* R_TX_OFF */ #define V_TX_SZ 0x01 #define V_TX_INIT 0x04 /* R_SYNC_CTRL */ #define V_EXT_CLK_SYNC 0x01 #define V_SYNC_OFFS 0x02 #define V_PCM_SYNC 0x04 #define V_NEG_CLK 0x08 #define V_HCLK 0x10 /* #define V_JATT_AUTO_DEL 0x20 #define V_JATT_AUTO 0x40 */ #define V_JATT_OFF 0x80 /* R_STATE */ #define V_E1_STA 0x01 #define V_ALT_FR_RX 0x40 #define V_ALT_FR_TX 0x80 /* R_SYNC_STA */ #define V_RX_STA 0x01 #define V_FR_SYNC_E1 0x04 #define V_SIG_LOS 0x08 #define V_MFA_STA 0x10 #define V_AIS 0x40 #define V_NO_MF_SYNC 0x80 /* R_RX_SL0_0 */ #define V_SI_FAS 0x01 #define V_SI_NFAS 0x02 #define V_A 0x04 #define V_CRC_OK 0x08 #define V_TX_E1 0x10 #define V_TX_E2 0x20 #define V_RX_E1 0x40 #define V_RX_E2 0x80 /* R_SLIP */ #define V_SLIP_RX 0x01 #define V_FOSLIP_RX 0x08 #define V_SLIP_TX 0x10 #define V_FOSLIP_TX 0x80 /* chapter 6: PCM interface */ /* R_PCM_MD0 */ #define V_PCM_MD 0x01 #define V_C4_POL 0x02 #define V_F0_NEG 0x04 #define V_F0_LEN 0x08 #define V_PCM_ADDR 0x10 /* R_SL_SEL0 */ #define V_SL_SEL0 0x01 #define V_SH_SEL0 0x80 /* R_SL_SEL1 */ #define V_SL_SEL1 0x01 #define V_SH_SEL1 0x80 /* R_SL_SEL2 */ #define V_SL_SEL2 0x01 #define V_SH_SEL2 0x80 /* R_SL_SEL3 */ #define V_SL_SEL3 0x01 #define V_SH_SEL3 0x80 /* R_SL_SEL4 */ #define V_SL_SEL4 0x01 #define V_SH_SEL4 0x80 /* R_SL_SEL5 */ #define V_SL_SEL5 0x01 #define V_SH_SEL5 0x80 /* R_SL_SEL6 */ #define V_SL_SEL6 0x01 #define V_SH_SEL6 0x80 /* R_SL_SEL7 */ #define V_SL_SEL7 0x01 #define V_SH_SEL7 0x80 /* R_PCM_MD1 */ #define V_ODEC_CON 0x01 #define V_PLL_ADJ 0x04 #define V_PCM_DR 0x10 #define V_PCM_LOOP 0x40 /* R_PCM_MD2 */ #define V_SYNC_PLL 0x02 #define V_SYNC_SRC 0x04 #define V_SYNC_OUT 0x08 #define V_ICR_FR_TIME 0x40 #define V_EN_PLL 0x80 /* chapter 7: pulse width modulation */ /* R_PWM_MD */ #define V_EXT_IRQ_EN 0x08 #define V_PWM0_MD 0x10 #define V_PWM1_MD 0x40 /* chapter 8: multiparty audio conferences */ /* R_CONF_EN */ #define V_CONF_EN 0x01 #define V_ULAW 0x80 /* A_CONF */ #define V_CONF_NUM 0x01 #define V_NOISE_SUPPR 0x08 #define V_ATT_LEV 0x20 #define V_CONF_SL 0x80 /* R_CONF_OFLOW */ #define V_CONF_OFLOW0 0x01 #define V_CONF_OFLOW1 0x02 #define V_CONF_OFLOW2 0x04 #define V_CONF_OFLOW3 0x08 #define V_CONF_OFLOW4 0x10 #define V_CONF_OFLOW5 0x20 #define V_CONF_OFLOW6 0x40 #define V_CONF_OFLOW7 0x80 /* chapter 9: DTMF contoller */ /* R_DTMF0 */ #define V_DTMF_EN 0x01 #define V_HARM_SEL 0x02 #define V_DTMF_RX_CH 0x04 #define V_DTMF_STOP 0x08 #define V_CHBL_SEL 0x10 #define V_RST_DTMF 0x40 #define V_ULAW_SEL 0x80 /* chapter 10: BERT */ /* R_BERT_WD_MD */ #define V_PAT_SEQ 0x01 #define V_BERT_ERR 0x08 #define V_AUTO_WD_RES 0x20 #define V_WD_RES 0x80 /* R_BERT_STA */ #define V_BERT_SYNC_SRC 0x01 #define V_BERT_SYNC 0x10 #define V_BERT_INV_DATA 0x20 /* chapter 11: auxiliary interface */ /* R_BRG_PCM_CFG */ #define V_BRG_EN 0x01 #define V_BRG_MD 0x02 #define V_PCM_CLK 0x20 #define V_ADDR_WRDLY 0x40 /* R_BRG_CTRL */ #define V_BRG_CS 0x01 #define V_BRG_ADDR 0x08 #define V_BRG_CS_SRC 0x80 /* R_BRG_MD */ #define V_BRG_MD0 0x01 #define V_BRG_MD1 0x02 #define V_BRG_MD2 0x04 #define V_BRG_MD3 0x08 #define V_BRG_MD4 0x10 #define V_BRG_MD5 0x20 #define V_BRG_MD6 0x40 #define V_BRG_MD7 0x80 /* R_BRG_TIM0 */ #define V_BRG_TIM0_IDLE 0x01 #define V_BRG_TIM0_CLK 0x10 /* R_BRG_TIM1 */ #define V_BRG_TIM1_IDLE 0x01 #define V_BRG_TIM1_CLK 0x10 /* R_BRG_TIM2 */ #define V_BRG_TIM2_IDLE 0x01 #define V_BRG_TIM2_CLK 0x10 /* R_BRG_TIM3 */ #define V_BRG_TIM3_IDLE 0x01 #define V_BRG_TIM3_CLK 0x10 /* R_BRG_TIM_SEL01 */ #define V_BRG_WR_SEL0 0x01 #define V_BRG_RD_SEL0 0x04 #define V_BRG_WR_SEL1 0x10 #define V_BRG_RD_SEL1 0x40 /* R_BRG_TIM_SEL23 */ #define V_BRG_WR_SEL2 0x01 #define V_BRG_RD_SEL2 0x04 #define V_BRG_WR_SEL3 0x10 #define V_BRG_RD_SEL3 0x40 /* R_BRG_TIM_SEL45 */ #define V_BRG_WR_SEL4 0x01 #define V_BRG_RD_SEL4 0x04 #define V_BRG_WR_SEL5 0x10 #define V_BRG_RD_SEL5 0x40 /* R_BRG_TIM_SEL67 */ #define V_BRG_WR_SEL6 0x01 #define V_BRG_RD_SEL6 0x04 #define V_BRG_WR_SEL7 0x10 #define V_BRG_RD_SEL7 0x40 /* chapter 12: clock, reset, interrupt, timer and watchdog */ /* R_IRQMSK_MISC */ #define V_STA_IRQMSK 0x01 #define V_TI_IRQMSK 0x02 #define V_PROC_IRQMSK 0x04 #define V_DTMF_IRQMSK 0x08 #define V_IRQ1S_MSK 0x10 #define V_SA6_IRQMSK 0x20 #define V_RX_EOMF_MSK 0x40 #define V_TX_EOMF_MSK 0x80 /* R_IRQ_CTRL */ #define V_FIFO_IRQ 0x01 #define V_GLOB_IRQ_EN 0x08 #define V_IRQ_POL 0x10 /* R_TI_WD */ #define V_EV_TS 0x01 #define V_WD_TS 0x10 /* A_IRQ_MSK */ #define V_IRQ 0x01 #define V_BERT_EN 0x02 #define V_MIX_IRQ 0x04 /* R_IRQ_OVIEW */ #define V_IRQ_FIFO_BL0 0x01 #define V_IRQ_FIFO_BL1 0x02 #define V_IRQ_FIFO_BL2 0x04 #define V_IRQ_FIFO_BL3 0x08 #define V_IRQ_FIFO_BL4 0x10 #define V_IRQ_FIFO_BL5 0x20 #define V_IRQ_FIFO_BL6 0x40 #define V_IRQ_FIFO_BL7 0x80 /* R_IRQ_MISC */ #define V_STA_IRQ 0x01 #define V_TI_IRQ 0x02 #define V_IRQ_PROC 0x04 #define V_DTMF_IRQ 0x08 #define V_IRQ1S 0x10 #define V_SA6_IRQ 0x20 #define V_RX_EOMF 0x40 #define V_TX_EOMF 0x80 /* R_STATUS */ #define V_BUSY 0x01 #define V_PROC 0x02 #define V_DTMF_STA 0x04 #define V_LOST_STA 0x08 #define V_SYNC_IN 0x10 #define V_EXT_IRQSTA 0x20 #define V_MISC_IRQSTA 0x40 #define V_FR_IRQSTA 0x80 /* R_IRQ_FIFO_BL0 */ #define V_IRQ_FIFO0_TX 0x01 #define V_IRQ_FIFO0_RX 0x02 #define V_IRQ_FIFO1_TX 0x04 #define V_IRQ_FIFO1_RX 0x08 #define V_IRQ_FIFO2_TX 0x10 #define V_IRQ_FIFO2_RX 0x20 #define V_IRQ_FIFO3_TX 0x40 #define V_IRQ_FIFO3_RX 0x80 /* R_IRQ_FIFO_BL1 */ #define V_IRQ_FIFO4_TX 0x01 #define V_IRQ_FIFO4_RX 0x02 #define V_IRQ_FIFO5_TX 0x04 #define V_IRQ_FIFO5_RX 0x08 #define V_IRQ_FIFO6_TX 0x10 #define V_IRQ_FIFO6_RX 0x20 #define V_IRQ_FIFO7_TX 0x40 #define V_IRQ_FIFO7_RX 0x80 /* R_IRQ_FIFO_BL2 */ #define V_IRQ_FIFO8_TX 0x01 #define V_IRQ_FIFO8_RX 0x02 #define V_IRQ_FIFO9_TX 0x04 #define V_IRQ_FIFO9_RX 0x08 #define V_IRQ_FIFO10_TX 0x10 #define V_IRQ_FIFO10_RX 0x20 #define V_IRQ_FIFO11_TX 0x40 #define V_IRQ_FIFO11_RX 0x80 /* R_IRQ_FIFO_BL3 */ #define V_IRQ_FIFO12_TX 0x01 #define V_IRQ_FIFO12_RX 0x02 #define V_IRQ_FIFO13_TX 0x04 #define V_IRQ_FIFO13_RX 0x08 #define V_IRQ_FIFO14_TX 0x10 #define V_IRQ_FIFO14_RX 0x20 #define V_IRQ_FIFO15_TX 0x40 #define V_IRQ_FIFO15_RX 0x80 /* R_IRQ_FIFO_BL4 */ #define V_IRQ_FIFO16_TX 0x01 #define V_IRQ_FIFO16_RX 0x02 #define V_IRQ_FIFO17_TX 0x04 #define V_IRQ_FIFO17_RX 0x08 #define V_IRQ_FIFO18_TX 0x10 #define V_IRQ_FIFO18_RX 0x20 #define V_IRQ_FIFO19_TX 0x40 #define V_IRQ_FIFO19_RX 0x80 /* R_IRQ_FIFO_BL5 */ #define V_IRQ_FIFO20_TX 0x01 #define V_IRQ_FIFO20_RX 0x02 #define V_IRQ_FIFO21_TX 0x04 #define V_IRQ_FIFO21_RX 0x08 #define V_IRQ_FIFO22_TX 0x10 #define V_IRQ_FIFO22_RX 0x20 #define V_IRQ_FIFO23_TX 0x40 #define V_IRQ_FIFO23_RX 0x80 /* R_IRQ_FIFO_BL6 */ #define V_IRQ_FIFO24_TX 0x01 #define V_IRQ_FIFO24_RX 0x02 #define V_IRQ_FIFO25_TX 0x04 #define V_IRQ_FIFO25_RX 0x08 #define V_IRQ_FIFO26_TX 0x10 #define V_IRQ_FIFO26_RX 0x20 #define V_IRQ_FIFO27_TX 0x40 #define V_IRQ_FIFO27_RX 0x80 /* R_IRQ_FIFO_BL7 */ #define V_IRQ_FIFO28_TX 0x01 #define V_IRQ_FIFO28_RX 0x02 #define V_IRQ_FIFO29_TX 0x04 #define V_IRQ_FIFO29_RX 0x08 #define V_IRQ_FIFO30_TX 0x10 #define V_IRQ_FIFO30_RX 0x20 #define V_IRQ_FIFO31_TX 0x40 #define V_IRQ_FIFO31_RX 0x80 /* chapter 13: general purpose I/O pins (GPIO) and input pins (GPI) */ /* R_GPIO_OUT0 */ #define V_GPIO_OUT0 0x01 #define V_GPIO_OUT1 0x02 #define V_GPIO_OUT2 0x04 #define V_GPIO_OUT3 0x08 #define V_GPIO_OUT4 0x10 #define V_GPIO_OUT5 0x20 #define V_GPIO_OUT6 0x40 #define V_GPIO_OUT7 0x80 /* R_GPIO_OUT1 */ #define V_GPIO_OUT8 0x01 #define V_GPIO_OUT9 0x02 #define V_GPIO_OUT10 0x04 #define V_GPIO_OUT11 0x08 #define V_GPIO_OUT12 0x10 #define V_GPIO_OUT13 0x20 #define V_GPIO_OUT14 0x40 #define V_GPIO_OUT15 0x80 /* R_GPIO_EN0 */ #define V_GPIO_EN0 0x01 #define V_GPIO_EN1 0x02 #define V_GPIO_EN2 0x04 #define V_GPIO_EN3 0x08 #define V_GPIO_EN4 0x10 #define V_GPIO_EN5 0x20 #define V_GPIO_EN6 0x40 #define V_GPIO_EN7 0x80 /* R_GPIO_EN1 */ #define V_GPIO_EN8 0x01 #define V_GPIO_EN9 0x02 #define V_GPIO_EN10 0x04 #define V_GPIO_EN11 0x08 #define V_GPIO_EN12 0x10 #define V_GPIO_EN13 0x20 #define V_GPIO_EN14 0x40 #define V_GPIO_EN15 0x80 /* R_GPIO_SEL */ #define V_GPIO_SEL0 0x01 #define V_GPIO_SEL1 0x02 #define V_GPIO_SEL2 0x04 #define V_GPIO_SEL3 0x08 #define V_GPIO_SEL4 0x10 #define V_GPIO_SEL5 0x20 #define V_GPIO_SEL6 0x40 #define V_GPIO_SEL7 0x80 /* R_GPIO_IN0 */ #define V_GPIO_IN0 0x01 #define V_GPIO_IN1 0x02 #define V_GPIO_IN2 0x04 #define V_GPIO_IN3 0x08 #define V_GPIO_IN4 0x10 #define V_GPIO_IN5 0x20 #define V_GPIO_IN6 0x40 #define V_GPIO_IN7 0x80 /* R_GPIO_IN1 */ #define V_GPIO_IN8 0x01 #define V_GPIO_IN9 0x02 #define V_GPIO_IN10 0x04 #define V_GPIO_IN11 0x08 #define V_GPIO_IN12 0x10 #define V_GPIO_IN13 0x20 #define V_GPIO_IN14 0x40 #define V_GPIO_IN15 0x80 /* R_GPI_IN0 */ #define V_GPI_IN0 0x01 #define V_GPI_IN1 0x02 #define V_GPI_IN2 0x04 #define V_GPI_IN3 0x08 #define V_GPI_IN4 0x10 #define V_GPI_IN5 0x20 #define V_GPI_IN6 0x40 #define V_GPI_IN7 0x80 /* R_GPI_IN1 */ #define V_GPI_IN8 0x01 #define V_GPI_IN9 0x02 #define V_GPI_IN10 0x04 #define V_GPI_IN11 0x08 #define V_GPI_IN12 0x10 #define V_GPI_IN13 0x20 #define V_GPI_IN14 0x40 #define V_GPI_IN15 0x80 /* R_GPI_IN2 */ #define V_GPI_IN16 0x01 #define V_GPI_IN17 0x02 #define V_GPI_IN18 0x04 #define V_GPI_IN19 0x08 #define V_GPI_IN20 0x10 #define V_GPI_IN21 0x20 #define V_GPI_IN22 0x40 #define V_GPI_IN23 0x80 /* R_GPI_IN3 */ #define V_GPI_IN24 0x01 #define V_GPI_IN25 0x02 #define V_GPI_IN26 0x04 #define V_GPI_IN27 0x08 #define V_GPI_IN28 0x10 #define V_GPI_IN29 0x20 #define V_GPI_IN30 0x40 #define V_GPI_IN31 0x80 /* map of all registers, used for debugging */ #ifdef HFC_REGISTER_DEBUG struct hfc_register_names { char *name; u_char reg; } hfc_register_names[] = { /* write registers */ {"R_CIRM", 0x00}, {"R_CTRL", 0x01}, {"R_BRG_PCM_CFG ", 0x02}, {"R_RAM_ADDR0", 0x08}, {"R_RAM_ADDR1", 0x09}, {"R_RAM_ADDR2", 0x0A}, {"R_FIRST_FIFO", 0x0B}, {"R_RAM_SZ", 0x0C}, {"R_FIFO_MD", 0x0D}, {"R_INC_RES_FIFO", 0x0E}, {"R_FIFO / R_FSM_IDX", 0x0F}, {"R_SLOT", 0x10}, {"R_IRQMSK_MISC", 0x11}, {"R_SCI_MSK", 0x12}, {"R_IRQ_CTRL", 0x13}, {"R_PCM_MD0", 0x14}, {"R_0x15", 0x15}, {"R_ST_SEL", 0x16}, {"R_ST_SYNC", 0x17}, {"R_CONF_EN", 0x18}, {"R_TI_WD", 0x1A}, {"R_BERT_WD_MD", 0x1B}, {"R_DTMF", 0x1C}, {"R_DTMF_N", 0x1D}, {"R_E1_XX_STA", 0x20}, {"R_LOS0", 0x22}, {"R_LOS1", 0x23}, {"R_RX0", 0x24}, {"R_RX_FR0", 0x25}, {"R_RX_FR1", 0x26}, {"R_TX0", 0x28}, {"R_TX1", 0x29}, {"R_TX_FR0", 0x2C}, {"R_TX_FR1", 0x2D}, {"R_TX_FR2", 0x2E}, {"R_JATT_ATT", 0x2F}, {"A_ST_xx_STA/R_RX_OFF", 0x30}, {"A_ST_CTRL0/R_SYNC_OUT", 0x31}, {"A_ST_CTRL1", 0x32}, {"A_ST_CTRL2", 0x33}, {"A_ST_SQ_WR", 0x34}, {"R_TX_OFF", 0x34}, {"R_SYNC_CTRL", 0x35}, {"A_ST_CLK_DLY", 0x37}, {"R_PWM0", 0x38}, {"R_PWM1", 0x39}, {"A_ST_B1_TX", 0x3C}, {"A_ST_B2_TX", 0x3D}, {"A_ST_D_TX", 0x3E}, {"R_GPIO_OUT0", 0x40}, {"R_GPIO_OUT1", 0x41}, {"R_GPIO_EN0", 0x42}, {"R_GPIO_EN1", 0x43}, {"R_GPIO_SEL", 0x44}, {"R_BRG_CTRL", 0x45}, {"R_PWM_MD", 0x46}, {"R_BRG_MD", 0x47}, {"R_BRG_TIM0", 0x48}, {"R_BRG_TIM1", 0x49}, {"R_BRG_TIM2", 0x4A}, {"R_BRG_TIM3", 0x4B}, {"R_BRG_TIM_SEL01", 0x4C}, {"R_BRG_TIM_SEL23", 0x4D}, {"R_BRG_TIM_SEL45", 0x4E}, {"R_BRG_TIM_SEL67", 0x4F}, {"A_FIFO_DATA0-2", 0x80}, {"A_FIFO_DATA0-2_NOINC", 0x84}, {"R_RAM_DATA", 0xC0}, {"A_SL_CFG", 0xD0}, {"A_CONF", 0xD1}, {"A_CH_MSK", 0xF4}, {"A_CON_HDLC", 0xFA}, {"A_SUBCH_CFG", 0xFB}, {"A_CHANNEL", 0xFC}, {"A_FIFO_SEQ", 0xFD}, {"A_IRQ_MSK", 0xFF}, {NULL, 0}, /* read registers */ {"A_Z1", 0x04}, {"A_Z1H", 0x05}, {"A_Z2", 0x06}, {"A_Z2H", 0x07}, {"A_F1", 0x0C}, {"A_F2", 0x0D}, {"R_IRQ_OVIEW", 0x10}, {"R_IRQ_MISC", 0x11}, {"R_IRQ_STATECH", 0x12}, {"R_CONF_OFLOW", 0x14}, {"R_RAM_USE", 0x15}, {"R_CHIP_ID", 0x16}, {"R_BERT_STA", 0x17}, {"R_F0_CNTL", 0x18}, {"R_F0_CNTH", 0x19}, {"R_BERT_ECL", 0x1A}, {"R_BERT_ECH", 0x1B}, {"R_STATUS", 0x1C}, {"R_CHIP_RV", 0x1F}, {"R_STATE", 0x20}, {"R_SYNC_STA", 0x24}, {"R_RX_SL0_0", 0x25}, {"R_RX_SL0_1", 0x26}, {"R_RX_SL0_2", 0x27}, {"R_JATT_DIR", 0x2b}, {"R_SLIP", 0x2c}, {"A_ST_RD_STA", 0x30}, {"R_FAS_ECL", 0x30}, {"R_FAS_ECH", 0x31}, {"R_VIO_ECL", 0x32}, {"R_VIO_ECH", 0x33}, {"R_CRC_ECL / A_ST_SQ_RD", 0x34}, {"R_CRC_ECH", 0x35}, {"R_E_ECL", 0x36}, {"R_E_ECH", 0x37}, {"R_SA6_SA13_ECL", 0x38}, {"R_SA6_SA13_ECH", 0x39}, {"R_SA6_SA23_ECL", 0x3A}, {"R_SA6_SA23_ECH", 0x3B}, {"A_ST_B1_RX", 0x3C}, {"A_ST_B2_RX", 0x3D}, {"A_ST_D_RX", 0x3E}, {"A_ST_E_RX", 0x3F}, {"R_GPIO_IN0", 0x40}, {"R_GPIO_IN1", 0x41}, {"R_GPI_IN0", 0x44}, {"R_GPI_IN1", 0x45}, {"R_GPI_IN2", 0x46}, {"R_GPI_IN3", 0x47}, {"A_FIFO_DATA0-2", 0x80}, {"A_FIFO_DATA0-2_NOINC", 0x84}, {"R_INT_DATA", 0x88}, {"R_RAM_DATA", 0xC0}, {"R_IRQ_FIFO_BL0", 0xC8}, {"R_IRQ_FIFO_BL1", 0xC9}, {"R_IRQ_FIFO_BL2", 0xCA}, {"R_IRQ_FIFO_BL3", 0xCB}, {"R_IRQ_FIFO_BL4", 0xCC}, {"R_IRQ_FIFO_BL5", 0xCD}, {"R_IRQ_FIFO_BL6", 0xCE}, {"R_IRQ_FIFO_BL7", 0xCF}, }; #endif /* HFC_REGISTER_DEBUG */