/*====================================================================== Device driver for the PCMCIA control functionality of StrongARM SA-1100 microprocessors. The contents of this file are subject to the Mozilla Public License Version 1.1 (the "License"); you may not use this file except in compliance with the License. You may obtain a copy of the License at http://www.mozilla.org/MPL/ Software distributed under the License is distributed on an "AS IS" basis, WITHOUT WARRANTY OF ANY KIND, either express or implied. See the License for the specific language governing rights and limitations under the License. The initial developer of the original code is John G. Dorsey . Portions created by John G. Dorsey are Copyright (C) 1999 John G. Dorsey. All Rights Reserved. Alternatively, the contents of this file may be used under the terms of the GNU Public License version 2 (the "GPL"), in which case the provisions of the GPL are applicable instead of the above. If you wish to allow the use of your version of this file only under the terms of the GPL and not to allow others to use your version of this file under the MPL, indicate your decision by deleting the provisions above and replace them with the notice and other provisions required by the GPL. If you do not delete the provisions above, a recipient may use your version of this file under either the MPL or the GPL. ======================================================================*/ #if !defined(_PCMCIA_SA1100_H) # define _PCMCIA_SA1100_H #include #include #include #include #include "cs_internal.h" #include /* MECR: Expansion Memory Configuration Register * (SA-1100 Developers Manual, p.10-13; SA-1110 Developers Manual, p.10-24) * * MECR layout is: * * FAST1 BSM1<4:0> BSA1<4:0> BSIO1<4:0> FAST0 BSM0<4:0> BSA0<4:0> BSIO0<4:0> * * (This layout is actually true only for the SA-1110; the FASTn bits are * reserved on the SA-1100.) */ #define MECR_SOCKET_0_SHIFT (0) #define MECR_SOCKET_1_SHIFT (16) #define MECR_BS_MASK (0x1f) #define MECR_FAST_MODE_MASK (0x01) #define MECR_BSIO_SHIFT (0) #define MECR_BSA_SHIFT (5) #define MECR_BSM_SHIFT (10) #define MECR_FAST_SHIFT (15) #define MECR_SET(mecr, sock, shift, mask, bs) \ ((mecr)=((mecr)&~(((mask)<<(shift))<<\ ((sock)==0?MECR_SOCKET_0_SHIFT:MECR_SOCKET_1_SHIFT)))|\ (((bs)<<(shift))<<((sock)==0?MECR_SOCKET_0_SHIFT:MECR_SOCKET_1_SHIFT))) #define MECR_GET(mecr, sock, shift, mask) \ ((((mecr)>>(((sock)==0)?MECR_SOCKET_0_SHIFT:MECR_SOCKET_1_SHIFT))>>\ (shift))&(mask)) #define MECR_BSIO_SET(mecr, sock, bs) \ MECR_SET((mecr), (sock), MECR_BSIO_SHIFT, MECR_BS_MASK, (bs)) #define MECR_BSIO_GET(mecr, sock) \ MECR_GET((mecr), (sock), MECR_BSIO_SHIFT, MECR_BS_MASK) #define MECR_BSA_SET(mecr, sock, bs) \ MECR_SET((mecr), (sock), MECR_BSA_SHIFT, MECR_BS_MASK, (bs)) #define MECR_BSA_GET(mecr, sock) \ MECR_GET((mecr), (sock), MECR_BSA_SHIFT, MECR_BS_MASK) #define MECR_BSM_SET(mecr, sock, bs) \ MECR_SET((mecr), (sock), MECR_BSM_SHIFT, MECR_BS_MASK, (bs)) #define MECR_BSM_GET(mecr, sock) \ MECR_GET((mecr), (sock), MECR_BSM_SHIFT, MECR_BS_MASK) #define MECR_FAST_SET(mecr, sock, fast) \ MECR_SET((mecr), (sock), MECR_FAST_SHIFT, MECR_FAST_MODE_MASK, (fast)) #define MECR_FAST_GET(mecr, sock) \ MECR_GET((mecr), (sock), MECR_FAST_SHIFT, MECR_FAST_MODE_MASK) /* This function implements the BS value calculation for setting the MECR * using integer arithmetic: */ static inline unsigned int sa1100_pcmcia_mecr_bs(unsigned int pcmcia_cycle_ns, unsigned int cpu_clock_khz){ unsigned int t = ((pcmcia_cycle_ns * cpu_clock_khz) / 6) - 1000000; return (t / 1000000) + (((t % 1000000) == 0) ? 0 : 1); } /* This function returns the (approxmiate) command assertion period, in * nanoseconds, for a given CPU clock frequency and MECR BS value: */ static inline unsigned int sa1100_pcmcia_cmd_time(unsigned int cpu_clock_khz, unsigned int pcmcia_mecr_bs){ return (((10000000 * 2) / cpu_clock_khz) * (3 * (pcmcia_mecr_bs + 1))) / 10; } /* SA-1100 PCMCIA Memory and I/O timing * ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ * The SA-1110 Developer's Manual, section 10.2.5, says the following: * * "To calculate the recommended BS_xx value for each address space: * divide the command width time (the greater of twIOWR and twIORD, * or the greater of twWE and twOE) by processor cycle time; divide * by 2; divide again by 3 (number of BCLK's per command assertion); * round up to the next whole number; and subtract 1." * * The PC Card Standard, Release 7, section 4.13.4, says that twIORD * has a minimum value of 165ns. Section 4.13.5 says that twIOWR has * a minimum value of 165ns, as well. Section 4.7.2 (describing * common and attribute memory write timing) says that twWE has a * minimum value of 150ns for a 250ns cycle time (for 5V operation; * see section 4.7.4), or 300ns for a 600ns cycle time (for 3.3V * operation, also section 4.7.4). Section 4.7.3 says that taOE * has a maximum value of 150ns for a 300ns cycle time (for 5V * operation), or 300ns for a 600ns cycle time (for 3.3V operation). * * When configuring memory maps, Card Services appears to adopt the policy * that a memory access time of "0" means "use the default." The default * PCMCIA I/O command width time is 165ns. The default PCMCIA 5V attribute * and memory command width time is 150ns; the PCMCIA 3.3V attribute and * memory command width time is 300ns. */ #define SA1100_PCMCIA_IO_ACCESS (165) #define SA1100_PCMCIA_5V_MEM_ACCESS (150) #define SA1100_PCMCIA_3V_MEM_ACCESS (300) /* The socket driver actually works nicely in interrupt-driven form, * so the (relatively infrequent) polling is "just to be sure." */ #define SA1100_PCMCIA_POLL_PERIOD (2*HZ) /* This structure encapsulates per-socket state which we might need to * use when responding to a Card Services query of some kind. */ struct sa1100_pcmcia_socket { socket_state_t cs_state; struct pcmcia_state k_state; unsigned int irq; void (*handler)(void *, unsigned int); void *handler_info; pccard_io_map io_map[MAX_IO_WIN]; pccard_mem_map mem_map[MAX_WIN]; ioaddr_t virt_io, phys_attr, phys_mem; unsigned short speed_io, speed_attr, speed_mem; }; /* I/O pins replacing memory pins * (PCMCIA System Architecture, 2nd ed., by Don Anderson, p.75) * * These signals change meaning when going from memory-only to * memory-or-I/O interface: */ #define iostschg bvd1 #define iospkr bvd2 /* * Declaration for all implementation specific low_level operations. */ extern struct pcmcia_low_level assabet_pcmcia_ops; extern struct pcmcia_low_level neponset_pcmcia_ops; extern struct pcmcia_low_level h3600_pcmcia_ops; extern struct pcmcia_low_level cerf_pcmcia_ops; extern struct pcmcia_low_level gcplus_pcmcia_ops; extern struct pcmcia_low_level xp860_pcmcia_ops; extern struct pcmcia_low_level yopy_pcmcia_ops; extern struct pcmcia_low_level pangolin_pcmcia_ops; extern struct pcmcia_low_level freebird_pcmcia_ops; extern struct pcmcia_low_level pfs168_pcmcia_ops; extern struct pcmcia_low_level jornada720_pcmcia_ops; extern struct pcmcia_low_level flexanet_pcmcia_ops; extern struct pcmcia_low_level simpad_pcmcia_ops; extern struct pcmcia_low_level graphicsmaster_pcmcia_ops; extern struct pcmcia_low_level adsbitsy_pcmcia_ops; extern struct pcmcia_low_level stork_pcmcia_ops; #endif /* !defined(_PCMCIA_SA1100_H) */