/*====================================================================== NinjaSCSI-3 / NinjaSCSI-32Bi PCMCIA SCSI hostadapter card driver By: YOKOTA Hiroshi Ver.2.0 Support 32bit PIO mode Ver.1.1.2 Fix for scatter list buffer exceeds Ver.1.1 Support scatter list Ver.0.1 Initial version This software may be used and distributed according to the terms of the GNU General Public License. ======================================================================*/ /*********************************************************************** This driver is for these PCcards. I-O DATA PCSC-F (Workbit NinjaSCSI-3) "WBT", "NinjaSCSI-3", "R1.0" I-O DATA CBSC-II (Workbit NinjaSCSI-32Bi in 16bit mode) "IO DATA", "CBSC16 ", "1" ***********************************************************************/ /* $Id: nsp_cs.c,v 1.42 2001/09/10 10:30:58 elca Exp $ */ #ifdef NSP_KERNEL_2_2 #include #include #endif #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include <../drivers/scsi/scsi.h> #include <../drivers/scsi/hosts.h> #include <../drivers/scsi/sd.h> #include #include #include #include #include #include #include #include "nsp_cs.h" MODULE_AUTHOR("YOKOTA Hiroshi "); MODULE_DESCRIPTION("WorkBit NinjaSCSI-3 / NinjaSCSI-32Bi(16bit) PCMCIA SCSI host adapter module"); MODULE_SUPPORTED_DEVICE("sd,sr,sg,st"); MODULE_LICENSE("GPL"); #ifdef PCMCIA_DEBUG static int pc_debug = PCMCIA_DEBUG; MODULE_PARM(pc_debug, "i"); MODULE_PARM_DESC(pc_debug, "set debug level"); static char *version = "$Id: nsp_cs.c,v 1.42 2001/09/10 10:30:58 elca Exp $"; #define DEBUG(n, args...) if (pc_debug>(n)) printk(KERN_DEBUG args) #else #define DEBUG(n, args...) /* */ #endif #include "nsp_io.h" /*====================================================================*/ typedef struct scsi_info_t { dev_link_t link; struct Scsi_Host *host; int ndev; dev_node_t node[8]; int stop; struct bus_operations *bus; } scsi_info_t; /*----------------------------------------------------------------*/ #if (KERNEL_VERSION(2,4,0) > LINUX_VERSION_CODE) #define PROC_SCSI_NSP PROC_SCSI_IBMMCA /* bad hack... */ static struct proc_dir_entry proc_scsi_nsp = { PROC_SCSI_NSP, 6, "nsp_cs", S_IFDIR | S_IRUGO | S_IXUGO, 2 }; #endif /*====================================================================*/ /* Parameters that can be set with 'insmod' */ static unsigned int irq_mask = 0xffff; MODULE_PARM(irq_mask, "i"); MODULE_PARM_DESC(irq_mask, "IRQ mask bits"); static int irq_list[4] = { -1 }; MODULE_PARM(irq_list, "1-4i"); MODULE_PARM_DESC(irq_list, "IRQ number list"); /*----------------------------------------------------------------*/ /* driver state info, local to driver */ static char nspinfo[100]; /* description */ /* /usr/src/linux/drivers/scsi/hosts.h */ static Scsi_Host_Template driver_template = { /* next: NULL,*/ #if (KERNEL_VERSION(2,3,99) > LINUX_VERSION_CODE) proc_dir: &proc_scsi_nsp, /* kernel 2.2 */ #else proc_name: "nsp_cs", /* kernel 2.4 */ #endif /* proc_info: NULL,*/ name: "WorkBit NinjaSCSI-3/32Bi", detect: nsp_detect, release: nsp_release, info: nsp_info, /* command: NULL,*/ queuecommand: nsp_queuecommand, /* eh_strategy_handler: nsp_eh_strategy,*/ eh_abort_handler: nsp_eh_abort, eh_device_reset_handler: nsp_eh_device_reset, eh_bus_reset_handler: nsp_eh_bus_reset, eh_host_reset_handler: nsp_eh_host_reset, abort: nsp_abort, reset: nsp_reset, /* slave_attach: NULL,*/ /* bios_param: NULL,*/ can_queue: 1, this_id: SCSI_INITIATOR_ID, sg_tablesize: SG_ALL, cmd_per_lun: 1, /* present: 0,*/ /* unchecked_isa_dma: 0,*/ use_clustering: DISABLE_CLUSTERING, use_new_eh_code: 0, /* emulated: 0,*/ }; static dev_link_t *dev_list = NULL; static dev_info_t dev_info = {"nsp_cs"}; static nsp_hw_data nsp_data; /***********************************************************/ static int nsp_queuecommand(Scsi_Cmnd *SCpnt, void (*done)(Scsi_Cmnd *)) { #ifdef PCMCIA_DEBUG //unsigned int host_id = SCpnt->host->this_id; //unsigned int base = SCpnt->host->io_port; unsigned char target = SCpnt->target; #endif nsp_hw_data *data = &nsp_data; DEBUG(0, __FUNCTION__ "() SCpnt=0x%p target=%d lun=%d buff=0x%p bufflen=%d use_sg=%d\n", SCpnt, target, SCpnt->lun, SCpnt->request_buffer, SCpnt->request_bufflen, SCpnt->use_sg); //DEBUG(0, " before CurrentSC=0x%p\n", data->CurrentSC); if(data->CurrentSC != NULL) { printk(KERN_DEBUG " " __FUNCTION__ "() CurrentSC!=NULL this can't be happen\n"); data->CurrentSC = NULL; SCpnt->result = DID_BAD_TARGET << 16; done(SCpnt); return -1; } show_command(SCpnt); SCpnt->scsi_done = done; data->CurrentSC = SCpnt; RESID = SCpnt->request_bufflen; SCpnt->SCp.Status = -1; SCpnt->SCp.Message = -1; SCpnt->SCp.have_data_in = IO_UNKNOWN; SCpnt->SCp.sent_command = 0; SCpnt->SCp.phase = PH_UNDETERMINED; /* setup scratch area SCp.ptr : buffer pointer SCp.this_residual : buffer length SCp.buffer : next buffer SCp.buffers_residual : left buffers in list SCp.phase : current state of the command */ if (SCpnt->use_sg) { SCpnt->SCp.buffer = (struct scatterlist *) SCpnt->request_buffer; SCpnt->SCp.ptr = SCpnt->SCp.buffer->address; SCpnt->SCp.this_residual = SCpnt->SCp.buffer->length; SCpnt->SCp.buffers_residual = SCpnt->use_sg - 1; } else { SCpnt->SCp.ptr = (char *) SCpnt->request_buffer; SCpnt->SCp.this_residual = SCpnt->request_bufflen; SCpnt->SCp.buffer = NULL; SCpnt->SCp.buffers_residual = 0; } if(nsphw_start_selection(SCpnt, data) == FALSE) { DEBUG(0, " selection fail\n"); data->CurrentSC = NULL; SCpnt->result = DID_NO_CONNECT << 16; done(SCpnt); return -1; } //DEBUG(0, __FUNCTION__ "() out\n"); return 0; } /* * setup PIO FIFO transfer mode and enable/disable to data out */ static void nsp_setup_fifo(nsp_hw_data *data, int enabled) { unsigned int base = data->BaseAddress; unsigned char transfer_mode_reg; //DEBUG(0, __FUNCTION__ "() enabled=%d\n", enabled); if (enabled != FALSE) { transfer_mode_reg = TRANSFER_GO | BRAIND; } else { transfer_mode_reg = 0; } transfer_mode_reg |= data->TransferMode; nsp_index_write(base, TRANSFERMODE, transfer_mode_reg); } /* * Initialize Ninja hardware */ static int nsphw_init(nsp_hw_data *data) { unsigned int base = data->BaseAddress; int i, j; sync_data tmp_sync = { SyncNegotiation: SYNC_NOT_YET, SyncPeriod: 0, SyncOffset: 0 }; DEBUG(0, __FUNCTION__ "() in base=0x%x\n", base); data->ScsiClockDiv = CLOCK_40M; data->CurrentSC = NULL; data->FifoCount = 0; data->TransferMode = MODE_IO8; /* setup sync data */ for ( i = 0; i < N_TARGET; i++ ) { for ( j = 0; j < N_LUN; j++ ) { data->Sync[i][j] = tmp_sync; } } /* block all interrupts */ nsp_write(base, IRQCONTROL, IRQCONTROL_ALLMASK); /* setup SCSI interface */ nsp_write(base, IFSELECT, IF_IFSEL); nsp_index_write(base, SCSIIRQMODE, 0); nsp_index_write(base, TRANSFERMODE, MODE_IO8); nsp_index_write(base, CLOCKDIV, data->ScsiClockDiv); nsp_index_write(base, PARITYCTRL, 0); nsp_index_write(base, POINTERCLR, POINTER_CLEAR | ACK_COUNTER_CLEAR | REQ_COUNTER_CLEAR | HOST_COUNTER_CLEAR); /* setup fifo asic */ nsp_write(base, IFSELECT, IF_REGSEL); nsp_index_write(base, TERMPWRCTRL, 0); if ((nsp_index_read(base, OTHERCONTROL) & TPWR_SENSE) == 0) { printk(KERN_INFO "nsp_cs: terminator power on\n"); nsp_index_write(base, TERMPWRCTRL, POWER_ON); } nsp_index_write(base, TIMERCOUNT, 0); nsp_index_write(base, TIMERCOUNT, 0); /* requires 2 times!! */ nsp_index_write(base, SYNCREG, 0); nsp_index_write(base, ACKWIDTH, 0); /* enable interrupts and ack them */ nsp_index_write(base, SCSIIRQMODE, SCSI_PHASE_CHANGE_EI | RESELECT_EI | SCSI_RESET_IRQ_EI ); nsp_write(base, IRQCONTROL, IRQCONTROL_ALLCLEAR); nsp_setup_fifo(data, FALSE); return TRUE; } /* * Start selection phase */ static unsigned int nsphw_start_selection(Scsi_Cmnd *SCpnt, nsp_hw_data *data) { unsigned int host_id = SCpnt->host->this_id; unsigned int base = SCpnt->host->io_port; unsigned char target = SCpnt->target; int wait_count; unsigned char phase, arbit; //DEBUG(0, __FUNCTION__ "()in\n"); phase = nsp_index_read(base, SCSIBUSMON); if(phase != BUSMON_BUS_FREE) { //DEBUG(0, " bus busy\n"); return FALSE; } /* start arbitration */ //DEBUG(0, " start arbit\n"); SCpnt->SCp.phase = PH_ARBSTART; nsp_index_write(base, SETARBIT, ARBIT_GO); wait_count = jiffies + 10 * HZ; do { /* XXX: what a stupid chip! */ arbit = nsp_index_read(base, ARBITSTATUS); //DEBUG(0, " arbit=%d, wait_count=%d\n", arbit, wait_count); udelay(1); /* hold 1.2us */ } while((arbit & (ARBIT_WIN | ARBIT_FAIL)) == 0 && time_before(jiffies, wait_count)); if((arbit & ARBIT_WIN) == 0) { //DEBUG(0, " arbit fail\n"); nsp_index_write(base, SETARBIT, ARBIT_FLAG_CLEAR); return FALSE; } /* assert select line */ //DEBUG(0, " assert SEL line\n"); SCpnt->SCp.phase = PH_SELSTART; udelay(3); nsp_index_write(base, SCSIDATALATCH, (1 << host_id) | (1 << target)); nsp_index_write(base, SCSIBUSCTRL, SCSI_SEL | SCSI_BSY | SCSI_ATN); udelay(3); nsp_index_write(base, SCSIBUSCTRL, SCSI_SEL | SCSI_BSY | SCSI_DATAOUT_ENB | SCSI_ATN); nsp_index_write(base, SETARBIT, ARBIT_FLAG_CLEAR); udelay(3); nsp_index_write(base, SCSIBUSCTRL, SCSI_SEL | SCSI_DATAOUT_ENB | SCSI_ATN); /* check selection timeout */ nsp_start_timer(SCpnt, data, 1000/51); data->SelectionTimeOut = 1; return TRUE; } struct nsp_sync_table { unsigned int min_period; unsigned int max_period; unsigned int chip_period; unsigned int ack_width; }; static struct nsp_sync_table nsp_sync_table_40M[] = { {0x0c,0x0c,0x1,0}, /* 20MB 50ns*/ {0x19,0x19,0x3,1}, /* 10MB 100ns*/ {0x1a,0x25,0x5,2}, /* 7.5MB 150ns*/ {0x26,0x32,0x7,3}, /* 5MB 200ns*/ {0x0, 0, 0, 0} }; static struct nsp_sync_table nsp_sync_table_20M[] = { {0x19,0x19,0x1,0}, /* 10MB 100ns*/ {0x1a,0x25,0x2,0}, /* 7.5MB 150ns*/ {0x26,0x32,0x3,1}, /* 5MB 200ns*/ {0x0, 0, 0, 0} }; /* * setup synchronous data transfer mode */ static int nsp_msg(Scsi_Cmnd *SCpnt, nsp_hw_data *data) { unsigned char target = SCpnt->target; unsigned char lun = SCpnt->lun; sync_data *sync = &(data->Sync[target][lun]); struct nsp_sync_table *sync_table; unsigned int period, offset; int i; DEBUG(0, __FUNCTION__ "()\n"); /**!**/ period = sync->SyncPeriod; offset = sync->SyncOffset; DEBUG(0, " period=0x%x, offset=0x%x\n", period, offset); if (data->ScsiClockDiv == CLOCK_20M) { sync_table = &nsp_sync_table_20M[0]; } else { sync_table = &nsp_sync_table_40M[0]; } for ( i = 0; sync_table->max_period != 0; i++, sync_table++) { if ( period >= sync_table->min_period && period <= sync_table->max_period ) { break; } } if (period != 0 && sync_table->max_period == 0) { /* * No proper period/offset found */ DEBUG(0, " no proper period/offset\n"); sync->SyncPeriod = 0; sync->SyncOffset = 0; sync->SyncRegister = 0; sync->AckWidth = 0; sync->SyncNegotiation = SYNC_OK; return FALSE; } sync->SyncRegister = (sync_table->chip_period << SYNCREG_PERIOD_SHIFT) | (offset & SYNCREG_OFFSET_MASK); sync->AckWidth = sync_table->ack_width; sync->SyncNegotiation = SYNC_OK; DEBUG(0, " sync_reg=0x%x, ack_width=0x%x\n", sync->SyncRegister, sync->AckWidth); return TRUE; } /* * start ninja hardware timer */ static void nsp_start_timer(Scsi_Cmnd *SCpnt, nsp_hw_data *data, int time) { unsigned int base = SCpnt->host->io_port; //DEBUG(0, __FUNCTION__ "() in SCpnt=0x%p, time=%d\n", SCpnt, time); data->TimerCount = time; nsp_index_write(base, TIMERCOUNT, time); } /* * wait for bus phase change */ static int nsp_negate_signal(Scsi_Cmnd *SCpnt, unsigned char mask, char *str) { unsigned int base = SCpnt->host->io_port; unsigned char reg; int count, i = TRUE; //DEBUG(0, __FUNCTION__ "()\n"); count = jiffies + HZ; do { reg = nsp_index_read(base, SCSIBUSMON); if (reg == 0xff) { break; } } while ((i = time_before(jiffies, count)) && (reg & mask) != 0); if (!i) { printk(KERN_DEBUG __FUNCTION__ " %s signal off timeut\n", str); } return 0; } /* * expect Ninja Irq */ static int nsp_expect_signal(Scsi_Cmnd *SCpnt, unsigned char current_phase, unsigned char mask) { unsigned int base = SCpnt->host->io_port; int wait_count; unsigned char phase, i_src; //DEBUG(0, __FUNCTION__ "() current_phase=0x%x, mask=0x%x\n", current_phase, mask); wait_count = jiffies + HZ; do { phase = nsp_index_read(base, SCSIBUSMON); if (phase == 0xff) { //DEBUG(0, " ret -1\n"); return -1; } i_src = nsp_read(base, IRQSTATUS); if (i_src & IRQSTATUS_SCSI) { //DEBUG(0, " ret 0 found scsi signal\n"); return 0; } if ((phase & mask) != 0 && (phase & BUSMON_PHASE_MASK) == current_phase) { //DEBUG(0, " ret 1 phase=0x%x\n", phase); return 1; } } while(time_before(jiffies, wait_count)); //DEBUG(0, __FUNCTION__ " : " __FUNCTION__ " timeout\n"); return -1; } /* * transfer SCSI message */ static int nsp_xfer(Scsi_Cmnd *SCpnt, nsp_hw_data *data, int phase) { unsigned int base = SCpnt->host->io_port; char *buf = data->MsgBuffer; int len = MIN(MSGBUF_SIZE, data->MsgLen); int ptr; int ret; //DEBUG(0, __FUNCTION__ "()\n"); for (ptr = 0; len > 0; len --, ptr ++) { ret = nsp_expect_signal(SCpnt, phase, BUSMON_REQ); if (ret <= 0) { DEBUG(0, " xfer quit\n"); return 0; } /* if last byte, negate ATN */ if (len == 1 && SCpnt->SCp.phase == PH_MSG_OUT) { nsp_index_write(base, SCSIBUSCTRL, AUTODIRECTION | ACKENB); } /* read & write message */ if (phase & BUSMON_IO) { DEBUG(0, " read msg\n"); buf[ptr] = nsp_index_read(base, SCSIDATAWITHACK); } else { DEBUG(0, " write msg\n"); nsp_index_write(base, SCSIDATAWITHACK, buf[ptr]); } nsp_negate_signal(SCpnt, BUSMON_ACK, "xfer"); } return len; } /* * get extra SCSI data from fifo */ static int nsp_dataphase_bypass(Scsi_Cmnd *SCpnt, nsp_hw_data *data) { unsigned int count; //DEBUG(0, __FUNCTION__ "()\n"); if (SCpnt->SCp.have_data_in != IO_IN) { return 0; } count = nsp_fifo_count(SCpnt); if (data->FifoCount == count) { //DEBUG(0, " not use bypass quirk\n"); return 0; } /* * XXX: NSP_QUIRK * data phase skip only occures in case of SCSI_LOW_READ */ SCpnt->SCp.phase = PH_DATA; nsp_pio_read(SCpnt, data); nsp_setup_fifo(data, FALSE); DEBUG(0, " use bypass quirk\n"); return 0; } /* * accept reselection */ static int nsp_reselected(Scsi_Cmnd *SCpnt, nsp_hw_data *data) { unsigned int base = SCpnt->host->io_port; unsigned char reg; //DEBUG(0, __FUNCTION__ "()\n"); nsp_negate_signal(SCpnt, BUSMON_SEL, "reselect"); nsp_nexus(SCpnt, data); reg = nsp_index_read(base, SCSIBUSCTRL) & ~(SCSI_BSY | SCSI_ATN); nsp_index_write(base, SCSIBUSCTRL, reg); nsp_index_write(base, SCSIBUSCTRL, reg | AUTODIRECTION | ACKENB); return TRUE; } /* * count how many data transferd */ static int nsp_fifo_count(Scsi_Cmnd *SCpnt) { unsigned int base = SCpnt->host->io_port; unsigned int count; unsigned int l, m, h; nsp_index_write(base, POINTERCLR, POINTER_CLEAR); l = (unsigned int)nsp_read(base, DATAREG); m = (unsigned int)nsp_read(base, DATAREG); h = (unsigned int)nsp_read(base, DATAREG); count = (h << 16) | (m << 8) | (l << 0); //DEBUG(0, __FUNCTION__ "() =0x%x\n", count); return count; } /* fifo size */ #define RFIFO_CRIT 64 #define WFIFO_CRIT 64 /* * read data in DATA IN phase */ static void nsp_pio_read(Scsi_Cmnd *SCpnt, nsp_hw_data *data) { unsigned int base = SCpnt->host->io_port; int time_out, i; int ocount, res; unsigned char stat, fifo_stat; ocount = data->FifoCount; DEBUG(0, __FUNCTION__ "() in SCpnt=0x%p resid=%d ocount=%d ptr=0x%p this_residual=%d buffers=0x%p nbuf=%d\n", SCpnt, RESID, ocount, SCpnt->SCp.ptr, SCpnt->SCp.this_residual, SCpnt->SCp.buffer, SCpnt->SCp.buffers_residual); time_out = jiffies + 10 * HZ; while ((i = time_before(jiffies,time_out)) && (SCpnt->SCp.this_residual > 0 || SCpnt->SCp.buffers_residual > 0 ) ) { stat = nsp_index_read(base, SCSIBUSMON); stat &= BUSMON_PHASE_MASK; res = nsp_fifo_count(SCpnt) - ocount; //DEBUG(0, " ptr=0x%p this=0x%x ocount=0x%x res=0x%x\n", SCpnt->SCp.ptr, SCpnt->SCp.this_residual, ocount, res); if (res == 0) { /* if some data avilable ? */ if (stat == BUSPHASE_DATA_IN) { /* phase changed? */ //DEBUG(0, " wait for data this=%d\n", SCpnt->SCp.this_residual); continue; } else { DEBUG(0, " phase changed stat=0x%x\n", stat); break; } } fifo_stat = nsp_read(base, FIFOSTATUS); if ((fifo_stat & FIFOSTATUS_FULL_EMPTY) == 0 && stat == BUSPHASE_DATA_IN) { continue; } res = MIN(res, SCpnt->SCp.this_residual); switch (data->TransferMode) { case MODE_IO32: res &= ~(BIT(1)|BIT(0)); /* align 4 */ nsp_fifo32_read(base, SCpnt->SCp.ptr, res >> 2); break; case MODE_IO8: nsp_fifo8_read (base, SCpnt->SCp.ptr, res ); break; default: DEBUG(0, "unknown read mode\n"); break; } RESID -= res; SCpnt->SCp.ptr += res; SCpnt->SCp.this_residual -= res; ocount += res; //DEBUG(0, " ptr=0x%p this_residual=0x%x ocount=0x%x\n", SCpnt->SCp.ptr, SCpnt->SCp.this_residual, ocount); /* go to next scatter list if availavle */ if (SCpnt->SCp.this_residual == 0 && SCpnt->SCp.buffers_residual != 0 ) { //DEBUG(0, " scatterlist next timeout=%d\n", time_out); SCpnt->SCp.buffers_residual--; SCpnt->SCp.buffer++; SCpnt->SCp.ptr = SCpnt->SCp.buffer->address; SCpnt->SCp.this_residual = SCpnt->SCp.buffer->length; } time_out = jiffies + 10 * HZ; } data->FifoCount = ocount; if (!i) { printk(KERN_DEBUG __FUNCTION__ "() pio read timeout resid=%d this_residual=%d buffers_residual=%d\n", RESID, SCpnt->SCp.this_residual, SCpnt->SCp.buffers_residual); } DEBUG(0, " read ocount=0x%x\n", ocount); } /* * write data in DATA OUT phase */ static void nsp_pio_write(Scsi_Cmnd *SCpnt, nsp_hw_data *data) { unsigned int base = SCpnt->host->io_port; int time_out, i; unsigned int ocount, res; unsigned char stat; ocount = data->FifoCount; DEBUG(0, __FUNCTION__ "() in fifocount=%d ptr=0x%p this_residual=%d buffers=0x%p nbuf=%d resid=0x%x\n", data->FifoCount, SCpnt->SCp.ptr, SCpnt->SCp.this_residual, SCpnt->SCp.buffer, SCpnt->SCp.buffers_residual, RESID); time_out = jiffies + 10 * HZ; while ((i = time_before(jiffies, time_out)) && (SCpnt->SCp.this_residual > 0 || SCpnt->SCp.buffers_residual > 0)) { stat = nsp_index_read(base, SCSIBUSMON); stat &= BUSMON_PHASE_MASK; if (stat != BUSPHASE_DATA_OUT) { DEBUG(0, " phase changed stat=0x%x\n", stat); break; } res = ocount - nsp_fifo_count(SCpnt); if (res > 0) { /* write all data? */ DEBUG(0, " wait for all data out. ocount=0x%x res=%d\n", ocount, res); continue; } res = MIN(SCpnt->SCp.this_residual, WFIFO_CRIT); //DEBUG(0, " ptr=0x%p this=0x%x res=0x%x\n", SCpnt->SCp.ptr, SCpnt->SCp.this_residual, res); switch (data->TransferMode) { case MODE_IO32: res &= ~(BIT(1)|BIT(0)); /* align 4 */ nsp_fifo32_write(base, SCpnt->SCp.ptr, res >> 2); break; case MODE_IO8: nsp_fifo8_write (base, SCpnt->SCp.ptr, res ); break; default: DEBUG(0, "unknown write mode\n"); break; } RESID -= res; SCpnt->SCp.ptr += res; SCpnt->SCp.this_residual -= res; ocount += res; /* go to next scatter list if availavle */ if (SCpnt->SCp.this_residual == 0 && SCpnt->SCp.buffers_residual != 0 ) { //DEBUG(0, " scatterlist next\n"); SCpnt->SCp.buffers_residual--; SCpnt->SCp.buffer++; SCpnt->SCp.ptr = SCpnt->SCp.buffer->address; SCpnt->SCp.this_residual = SCpnt->SCp.buffer->length; } time_out = jiffies + 10 * HZ; } data->FifoCount = ocount; if (!i) { printk(KERN_DEBUG __FUNCTION__ "() pio write timeout resid=%d\n", RESID); } //DEBUG(0, " write ocount=%d\n", ocount); } #undef RFIFO_CRIT #undef WFIFO_CRIT /* * setup synchronous/asynchronous data transfer mode */ static int nsp_nexus(Scsi_Cmnd *SCpnt, nsp_hw_data *data) { unsigned int base = SCpnt->host->io_port; unsigned char target = SCpnt->target; unsigned char lun = SCpnt->lun; sync_data *sync = &(data->Sync[target][lun]); //DEBUG(0, __FUNCTION__ "() in SCpnt=0x%p\n", SCpnt); /* setup synch transfer registers */ nsp_index_write(base, SYNCREG, sync->SyncRegister); nsp_index_write(base, ACKWIDTH, sync->AckWidth); if (RESID % 4 != 0 || RESID <= 256 ) { data->TransferMode = MODE_IO8; } else { data->TransferMode = MODE_IO32; } /* setup pdma fifo */ nsp_setup_fifo(data, TRUE); /* clear ack counter */ data->FifoCount = 0; nsp_index_write(base, POINTERCLR, POINTER_CLEAR | ACK_COUNTER_CLEAR | REQ_COUNTER_CLEAR | HOST_COUNTER_CLEAR); return 0; } #include "nsp_message.c" /* * interrupt handler */ static void nspintr(int irq, void *dev_id, struct pt_regs *regs) { unsigned int base; unsigned char i_src, irq_phase, phase; Scsi_Cmnd *tmpSC; int len; unsigned char target, lun; unsigned int *sync_neg; int i, tmp; nsp_hw_data *data; //printk("&nsp_data=0x%p, dev_id=0x%p\n", &nsp_data, dev_id); /* sanity check */ if (&nsp_data != dev_id) { DEBUG(0, " irq conflict? this can't happen\n"); return; } data = dev_id; if (irq != data->IrqNumber) { return; } base = data->BaseAddress; //DEBUG(0, " base=0x%x\n", base); /* * interrupt check */ nsp_write(base, IRQCONTROL, IRQCONTROL_IRQDISABLE); i_src = nsp_read(base, IRQSTATUS); if (i_src == 0xff || (i_src & IRQSTATUS_MASK) == 0) { nsp_write(base, IRQCONTROL, 0); //DEBUG(0, " no irq\n"); return; } //DEBUG(0, " i_src=0x%x\n", i_src); /* XXX: IMPORTANT * Do not read an irq_phase register if no scsi phase interrupt. * Unless, you should lose a scsi phase interrupt. */ phase = nsp_index_read(base, SCSIBUSMON); if((i_src & IRQSTATUS_SCSI) != 0) { irq_phase = nsp_index_read(base, IRQPHASESENCE); } else { irq_phase = 0; } //DEBUG(0, " irq_phase=0x%x\n", irq_phase); /* * timer interrupt handler (scsi vs timer interrupts) */ //DEBUG(0, " timercount=%d\n", data->TimerCount); if (data->TimerCount != 0) { //DEBUG(0, " stop timer\n"); nsp_index_write(base, TIMERCOUNT, 0); nsp_index_write(base, TIMERCOUNT, 0); data->TimerCount = 0; } if ((i_src & IRQSTATUS_MASK) == IRQSTATUS_TIMER && data->SelectionTimeOut == 0) { //DEBUG(0, " timer start\n"); nsp_write(base, IRQCONTROL, IRQCONTROL_TIMER_CLEAR); return; } nsp_write(base, IRQCONTROL, IRQCONTROL_TIMER_CLEAR | IRQCONTROL_FIFO_CLEAR); if (data->CurrentSC == NULL) { printk(KERN_DEBUG __FUNCTION__ " CurrentSC==NULL irq_status=0x%x phase=0x%x irq_phase=0x%x this can't be happen\n", i_src, phase, irq_phase); return; } else { tmpSC = data->CurrentSC; target = tmpSC->target; lun = tmpSC->lun; sync_neg = &(data->Sync[target][lun].SyncNegotiation); } /* * parse hardware SCSI irq reasons register */ if ((i_src & IRQSTATUS_SCSI) != 0) { if ((irq_phase & SCSI_RESET_IRQ) != 0) { printk(KERN_DEBUG " " __FUNCTION__ "() bus reset (power off?)\n"); *sync_neg = SYNC_NOT_YET; data->CurrentSC = NULL; tmpSC->result = DID_RESET << 16; tmpSC->scsi_done(tmpSC); return; } if ((irq_phase & RESELECT_IRQ) != 0) { DEBUG(0, " reselect\n"); nsp_write(base, IRQCONTROL, IRQCONTROL_RESELECT_CLEAR); if (nsp_reselected(tmpSC, data) != FALSE) { return; } } if ((irq_phase & (PHASE_CHANGE_IRQ | LATCHED_BUS_FREE)) == 0) { return; } } //show_phase(tmpSC); switch(tmpSC->SCp.phase) { case PH_SELSTART: *sync_neg = SYNC_NOT_YET; if ((phase & BUSMON_BSY) == 0) { //DEBUG(0, " selection count=%d\n", data->SelectionTimeOut); if (data->SelectionTimeOut >= NSP_SELTIMEOUT) { DEBUG(0, " selection time out\n"); data->SelectionTimeOut = 0; nsp_index_write(base, SCSIBUSCTRL, 0); data->CurrentSC = NULL; tmpSC->result = DID_NO_CONNECT << 16; tmpSC->scsi_done(tmpSC); return; } data->SelectionTimeOut += 1; nsp_start_timer(tmpSC, data, 1000/51); return; } /* attention assert */ //DEBUG(0, " attention assert\n"); data->SelectionTimeOut = 0; tmpSC->SCp.phase = PH_SELECTED; nsp_index_write(base, SCSIBUSCTRL, SCSI_ATN); udelay(1); nsp_index_write(base, SCSIBUSCTRL, SCSI_ATN | AUTODIRECTION | ACKENB); return; break; case PH_RESELECT: //DEBUG(0, " phase reselect\n"); *sync_neg = SYNC_NOT_YET; if ((phase & BUSMON_PHASE_MASK) != BUSPHASE_MESSAGE_IN) { data->CurrentSC = NULL; tmpSC->result = DID_ABORT << 16; tmpSC->scsi_done(tmpSC); return; } /* fall thru */ default: if ((i_src & (IRQSTATUS_SCSI | IRQSTATUS_FIFO)) == 0) { return; } break; } /* * SCSI sequencer */ //DEBUG(0, " start scsi seq\n"); /* normal disconnect */ if ((irq_phase & LATCHED_BUS_FREE) != 0) { //DEBUG(0, " normal disconnect i_src=0x%x, phase=0x%x, irq_phase=0x%x\n", i_src, phase, irq_phase); if ((tmpSC->SCp.Message == MSG_COMMAND_COMPLETE)) { /* all command complete and return status */ *sync_neg = SYNC_NOT_YET; data->CurrentSC = NULL; tmpSC->result = (DID_OK << 16) | (tmpSC->SCp.Message << 8) | (tmpSC->SCp.Status << 0); DEBUG(0, " command complete result=0x%x\n", tmpSC->result); tmpSC->scsi_done(tmpSC); return; } return; } /* check unexpected bus free state */ if (phase == 0) { printk(KERN_DEBUG " " __FUNCTION__ " unexpected bus free. i_src=0x%x, phase=0x%x, irq_phase=0x%x\n", i_src, phase, irq_phase); *sync_neg = SYNC_NOT_YET; data->CurrentSC = NULL; tmpSC->result = DID_ERROR << 16; tmpSC->scsi_done(tmpSC); return; } switch (phase & BUSMON_PHASE_MASK) { case BUSPHASE_COMMAND: DEBUG(0, " BUSPHASE_COMMAND\n"); if ((phase & BUSMON_REQ) == 0) { DEBUG(0, " REQ == 0\n"); return; } tmpSC->SCp.phase = PH_COMMAND; nsp_nexus(tmpSC, data); /* write scsi command */ nsp_index_write(base, COMMANDCTRL, CLEAR_COMMAND_POINTER); for (len = 0; len < COMMAND_SIZE(tmpSC->cmnd[0]); len++) { nsp_index_write(base, COMMANDDATA, tmpSC->cmnd[len]); } nsp_index_write(base, COMMANDCTRL, CLEAR_COMMAND_POINTER | AUTO_COMMAND_GO); break; case BUSPHASE_DATA_OUT: DEBUG(0, " BUSPHASE_DATA_OUT\n"); tmpSC->SCp.phase = PH_DATA; tmpSC->SCp.have_data_in = IO_OUT; nsp_pio_write(tmpSC, data); break; case BUSPHASE_DATA_IN: DEBUG(0, " BUSPHASE_DATA_IN\n"); tmpSC->SCp.phase = PH_DATA; tmpSC->SCp.have_data_in = IO_IN; nsp_pio_read(tmpSC, data); break; case BUSPHASE_STATUS: nsp_dataphase_bypass(tmpSC, data); DEBUG(0, " BUSPHASE_STATUS\n"); tmpSC->SCp.phase = PH_STATUS; tmpSC->SCp.Status = nsp_index_read(base, SCSIDATAWITHACK); //DEBUG(0, " message=0x%x status=0x%x\n", tmpSC->SCp.Message, tmpSC->SCp.Status); break; case BUSPHASE_MESSAGE_OUT: DEBUG(0, " BUSPHASE_MESSAGE_OUT\n"); if ((phase & BUSMON_REQ) == 0) { goto timer_out; } tmpSC->SCp.phase = PH_MSG_OUT; data->MsgLen = len = 0; if (*sync_neg == SYNC_NOT_YET) { data->Sync[target][lun].SyncPeriod = 0; data->Sync[target][lun].SyncOffset = 0; nsp_msg(tmpSC, data); data->MsgBuffer[len] = IDENTIFY(TRUE, lun); len++; /* data->MsgBuffer[len] = MSG_EXTENDED; len++; data->MsgBuffer[len] = 3; len++; data->MsgBuffer[len] = MSG_EXT_SDTR; len++; data->MsgBuffer[len] = 0x0c; len++; data->MsgBuffer[len] = 15; len++; */ } if (len == 0) { data->MsgBuffer[len] = MSG_NO_OPERATION; len++; } data->MsgLen = len; show_message(data); nsp_message_out(tmpSC, data); break; case BUSPHASE_MESSAGE_IN: nsp_dataphase_bypass(tmpSC, data); DEBUG(0, " BUSPHASE_MESSAGE_IN\n"); if ((phase & BUSMON_REQ) == 0) { goto timer_out; } tmpSC->SCp.phase = PH_MSG_IN; nsp_message_in(tmpSC, data); /* if (data->MsgLen >= 5 && data->MsgBuffer[0] == MSG_EXTENDED && data->MsgBuffer[1] == 3 && data->MsgBuffer[2] == MSG_EXT_SDTR ) { data->Sync[target][lun].SyncPeriod = data->MsgBuffer[3]; data->Sync[target][lun].SyncOffset = data->MsgBuffer[4]; nsp_msg(tmpSC, data); } */ /* search last messeage byte */ tmp = -1; for (i = 0; i < data->MsgLen; i++) { tmp = data->MsgBuffer[i]; if (data->MsgBuffer[i] == MSG_EXTENDED) { i += (1 + data->MsgBuffer[i+1]); } } tmpSC->SCp.Message = tmp; DEBUG(0, " message=0x%x len=%d\n", tmpSC->SCp.Message, data->MsgLen); show_message(data); break; case BUSPHASE_SELECT: default: DEBUG(0, " BUSPHASE other\n"); break; } //DEBUG(0, __FUNCTION__ "() out\n"); return; timer_out: nsp_start_timer(tmpSC, data, 1000/102); return; } #ifdef PCMCIA_DEBUG #include "nsp_debug.c" #endif /* DBG_SHOWCOMMAND */ /*----------------------------------------------------------------*/ /* look for ninja3 card and init if found */ /*----------------------------------------------------------------*/ static int nsp_detect(Scsi_Host_Template *sht) { struct Scsi_Host *host; /* registered host structure */ nsp_hw_data *data = &nsp_data; DEBUG(0, __FUNCTION__ " this_id=%d\n", sht->this_id); request_region(data->BaseAddress, data->NumAddress, "nsp_cs"); host = scsi_register(sht, 0); host->io_port = data->BaseAddress; host->unique_id = data->BaseAddress; host->n_io_port = data->NumAddress; host->irq = data->IrqNumber; host->dma_channel = 0xff; /* not use dms */ sprintf(nspinfo, /* Buffer size is 100 bytes */ /* 0 1 2 3 4 5 6 7 8 9 0*/ /* 01234567890123456789012345678901234567890123456789012345678901234567890123456789012345678901234567890*/ "NinjaSCSI-3/32Bi Driver $Revision: 1.42 $, I/O 0x%04lx-0x%04lx IRQ %2d", host->io_port, host->io_port + host->n_io_port, host->irq); sht->name = nspinfo; DEBUG(0, __FUNCTION__ " end\n"); return 1; /* detect done. */ } /* nsp_cs requires own release handler because its uses dev_id (=data) */ static int nsp_release(struct Scsi_Host *shpnt) { nsp_hw_data *data = &nsp_data; if (shpnt->irq) { free_irq(shpnt->irq, data); } if (shpnt->io_port && shpnt->n_io_port) { release_region(shpnt->io_port, shpnt->n_io_port); } return 0; } /*----------------------------------------------------------------*/ /* return info string */ /*----------------------------------------------------------------*/ static const char *nsp_info(struct Scsi_Host *shpnt) { return nspinfo; } /*---------------------------------------------------------------*/ /* error handler */ /*---------------------------------------------------------------*/ static int nsp_reset(Scsi_Cmnd *SCpnt, unsigned int why) { DEBUG(0, __FUNCTION__ " SCpnt=0x%p why=%d\n", SCpnt, why); nsp_eh_bus_reset(SCpnt); return SCSI_RESET_SUCCESS; } static int nsp_abort(Scsi_Cmnd *SCpnt) { DEBUG(0, __FUNCTION__ " SCpnt=0x%p\n", SCpnt); nsp_eh_bus_reset(SCpnt); return SCSI_ABORT_SUCCESS; } /*static int nsp_eh_strategy(struct Scsi_Host *Shost) { return FAILED; }*/ static int nsp_eh_abort(Scsi_Cmnd *SCpnt) { DEBUG(0, __FUNCTION__ " SCpnt=0x%p\n", SCpnt); nsp_eh_bus_reset(SCpnt); return SUCCESS; } static int nsp_eh_device_reset(Scsi_Cmnd *SCpnt) { DEBUG(0, __FUNCTION__ " SCpnt=0x%p\n", SCpnt); return FAILED; } static int nsp_eh_bus_reset(Scsi_Cmnd *SCpnt) { unsigned int base = SCpnt->host->io_port; int i; DEBUG(0, __FUNCTION__ "() SCpnt=0x%p base=0x%x\n", SCpnt, base); nsp_write(base, IRQCONTROL, IRQCONTROL_ALLMASK); nsp_index_write(base, SCSIBUSCTRL, SCSI_RST); mdelay(100); /* 100ms */ nsp_index_write(base, SCSIBUSCTRL, 0); for(i = 0; i < 5; i++) { nsp_index_read(base, IRQPHASESENCE); /* dummy read */ } nsp_write(base, IRQCONTROL, IRQCONTROL_ALLCLEAR); return SUCCESS; } static int nsp_eh_host_reset(Scsi_Cmnd *SCpnt) { nsp_hw_data *data = &nsp_data; DEBUG(0, __FUNCTION__ "\n"); nsphw_init(data); return nsp_eh_bus_reset(SCpnt); } /********************************************************************** PCMCIA functions *********************************************************************/ /*====================================================================*/ static void cs_error(client_handle_t handle, int func, int ret) { error_info_t err = { func, ret }; CardServices(ReportError, handle, &err); } /*====================================================================== nsp_cs_attach() creates an "instance" of the driver, allocating local data structures for one device. The device is registered with Card Services. The dev_link structure is initialized, but we don't actually configure the card at this point -- we wait until we receive a card insertion event. ======================================================================*/ static dev_link_t *nsp_cs_attach(void) { scsi_info_t *info; client_reg_t client_reg; dev_link_t *link; int ret, i; DEBUG(0, __FUNCTION__ "()\n"); /* Create new SCSI device */ info = kmalloc(sizeof(*info), GFP_KERNEL); if (!info) { return NULL; } memset(info, 0, sizeof(*info)); link = &info->link; link->priv = info; /* Initialize the dev_link_t structure */ link->release.function = &nsp_cs_release; link->release.data = (u_long)link; /* The io structure describes IO port mapping */ link->io.NumPorts1 = 0x10; link->io.Attributes1 = IO_DATA_PATH_WIDTH_AUTO; link->io.IOAddrLines = 10; /* not used */ /* Interrupt setup */ link->irq.Attributes = IRQ_TYPE_EXCLUSIVE | IRQ_HANDLE_PRESENT; link->irq.IRQInfo1 = IRQ_INFO2_VALID | IRQ_LEVEL_ID; if (irq_list[0] == -1) { link->irq.IRQInfo2 = irq_mask; } else { for (i = 0; i < 4; i++) { link->irq.IRQInfo2 |= 1 << irq_list[i]; } } link->irq.Handler = &nspintr; link->irq.Instance = &nsp_data; /* General socket configuration */ link->conf.Attributes = CONF_ENABLE_IRQ; link->conf.Vcc = 50; link->conf.IntType = INT_MEMORY_AND_IO; link->conf.Present = PRESENT_OPTION; /* Register with Card Services */ link->next = dev_list; dev_list = link; client_reg.dev_info = &dev_info; client_reg.Attributes = INFO_IO_CLIENT | INFO_CARD_SHARE; client_reg.EventMask = CS_EVENT_CARD_INSERTION | CS_EVENT_CARD_REMOVAL | CS_EVENT_RESET_PHYSICAL | CS_EVENT_CARD_RESET | CS_EVENT_PM_SUSPEND | CS_EVENT_PM_RESUME ; client_reg.event_handler = &nsp_cs_event; client_reg.Version = 0x0210; client_reg.event_callback_args.client_data = link; ret = CardServices(RegisterClient, &link->handle, &client_reg); if (ret != CS_SUCCESS) { cs_error(link->handle, RegisterClient, ret); nsp_cs_detach(link); return NULL; } return link; } /* nsp_cs_attach */ /*====================================================================== This deletes a driver "instance". The device is de-registered with Card Services. If it has been released, all local data structures are freed. Otherwise, the structures will be freed when the device is released. ======================================================================*/ static void nsp_cs_detach(dev_link_t *link) { dev_link_t **linkp; DEBUG(0, __FUNCTION__ "(0x%p)\n", link); /* Locate device structure */ for (linkp = &dev_list; *linkp; linkp = &(*linkp)->next) { if (*linkp == link) { break; } } if (*linkp == NULL) { return; } del_timer(&link->release); if (link->state & DEV_CONFIG) { nsp_cs_release((u_long)link); if (link->state & DEV_STALE_CONFIG) { link->state |= DEV_STALE_LINK; return; } } /* Break the link with Card Services */ if (link->handle) { CardServices(DeregisterClient, link->handle); } /* Unlink device structure, free bits */ *linkp = link->next; kfree(link->priv); } /* nsp_cs_detach */ /*====================================================================== nsp_cs_config() is scheduled to run after a CARD_INSERTION event is received, to configure the PCMCIA socket, and to make the ethernet device available to the system. ======================================================================*/ #define CS_CHECK(fn, args...) \ while ((last_ret=CardServices(last_fn=(fn),args))!=0) goto cs_failed #define CFG_CHECK(fn, args...) \ if (CardServices(fn, args) != 0) goto next_entry /*====================================================================*/ static void nsp_cs_config(dev_link_t *link) { client_handle_t handle = link->handle; scsi_info_t *info = link->priv; tuple_t tuple; cisparse_t parse; int i, last_ret, last_fn; u_char tuple_data[64]; config_info_t conf; Scsi_Device *dev; dev_node_t **tail, *node; struct Scsi_Host *host; nsp_hw_data *data = &nsp_data; DEBUG(0, __FUNCTION__ "() in\n"); tuple.DesiredTuple = CISTPL_CONFIG; tuple.Attributes = 0; tuple.TupleData = tuple_data; tuple.TupleDataMax = sizeof(tuple_data); tuple.TupleOffset = 0; CS_CHECK(GetFirstTuple, handle, &tuple); CS_CHECK(GetTupleData, handle, &tuple); CS_CHECK(ParseTuple, handle, &tuple, &parse); link->conf.ConfigBase = parse.config.base; link->conf.Present = parse.config.rmask[0]; /* Configure card */ driver_template.module = &__this_module; link->state |= DEV_CONFIG; /* Look up the current Vcc */ CS_CHECK(GetConfigurationInfo, handle, &conf); link->conf.Vcc = conf.Vcc; tuple.DesiredTuple = CISTPL_CFTABLE_ENTRY; CS_CHECK(GetFirstTuple, handle, &tuple); while (1) { CFG_CHECK(GetTupleData, handle, &tuple); CFG_CHECK(ParseTuple, handle, &tuple, &parse); link->conf.ConfigIndex = parse.cftable_entry.index; link->io.BasePort1 = parse.cftable_entry.io.win[0].base; i = CardServices(RequestIO, handle, &link->io); if (i == CS_SUCCESS) { break; } next_entry: DEBUG(0, __FUNCTION__ " next\n"); CS_CHECK(GetNextTuple, handle, &tuple); } CS_CHECK(RequestIRQ, handle, &link->irq); CS_CHECK(RequestConfiguration, handle, &link->conf); /* A bad hack... */ release_region(link->io.BasePort1, link->io.NumPorts1); /* Set port and IRQ */ data->BaseAddress = link->io.BasePort1; data->NumAddress = link->io.NumPorts1; data->IrqNumber = link->irq.AssignedIRQ; DEBUG(0, __FUNCTION__ " I/O[0x%x+0x%x] IRQ %d\n", data->BaseAddress, data->NumAddress, data->IrqNumber); if(nsphw_init(data) == FALSE) { goto cs_failed; } scsi_register_module(MODULE_SCSI_HA, &driver_template); DEBUG(0, "GET_SCSI_INFO\n"); tail = &link->dev; info->ndev = 0; for (host = scsi_hostlist; host != NULL; host = host->next) { if (host->hostt == &driver_template) { for (dev = host->host_queue; dev != NULL; dev = dev->next) { u_long arg[2], id; kernel_scsi_ioctl(dev, SCSI_IOCTL_GET_IDLUN, arg); id = (arg[0]&0x0f) + ((arg[0]>>4)&0xf0) + ((arg[0]>>8)&0xf00) + ((arg[0]>>12)&0xf000); node = &info->node[info->ndev]; node->minor = 0; switch (dev->type) { case TYPE_TAPE: node->major = SCSI_TAPE_MAJOR; sprintf(node->dev_name, "st#%04lx", id); break; case TYPE_DISK: case TYPE_MOD: node->major = SCSI_DISK0_MAJOR; sprintf(node->dev_name, "sd#%04lx", id); break; case TYPE_ROM: case TYPE_WORM: node->major = SCSI_CDROM_MAJOR; sprintf(node->dev_name, "sr#%04lx", id); break; default: node->major = SCSI_GENERIC_MAJOR; sprintf(node->dev_name, "sg#%04lx", id); break; } *tail = node; tail = &node->next; info->ndev++; info->host = dev->host; } } } *tail = NULL; if (info->ndev == 0) { printk(KERN_INFO "nsp_cs: no SCSI devices found\n"); } /* Finally, report what we've done */ printk(KERN_INFO "nsp_cs: index 0x%02x: Vcc %d.%d", link->conf.ConfigIndex, link->conf.Vcc/10, link->conf.Vcc%10); if (link->conf.Vpp1) { printk(", Vpp %d.%d", link->conf.Vpp1/10, link->conf.Vpp1%10); } if (link->conf.Attributes & CONF_ENABLE_IRQ) { printk(", irq %d", link->irq.AssignedIRQ); } if (link->io.NumPorts1) { printk(", io 0x%04x-0x%04x", link->io.BasePort1, link->io.BasePort1+link->io.NumPorts1-1); } printk("\n"); link->state &= ~DEV_CONFIG_PENDING; return; cs_failed: cs_error(link->handle, last_fn, last_ret); nsp_cs_release((u_long)link); return; } /* nsp_cs_config */ #undef CS_CHECK #undef CFG_CHECK /*====================================================================== After a card is removed, nsp_cs_release() will unregister the net device, and release the PCMCIA configuration. If the device is still open, this will be postponed until it is closed. ======================================================================*/ static void nsp_cs_release(u_long arg) { dev_link_t *link = (dev_link_t *)arg; DEBUG(0, __FUNCTION__ "(0x%p)\n", link); /* * If the device is currently in use, we won't release until it * is actually closed. */ if (link->open) { DEBUG(1, "nsp_cs: release postponed, '%s' still open\n", link->dev->dev_name); link->state |= DEV_STALE_CONFIG; return; } /* Unlink the device chain */ scsi_unregister_module(MODULE_SCSI_HA, &driver_template); link->dev = NULL; if (link->win) { CardServices(ReleaseWindow, link->win); } CardServices(ReleaseConfiguration, link->handle); if (link->io.NumPorts1) { CardServices(ReleaseIO, link->handle, &link->io); } if (link->irq.AssignedIRQ) { CardServices(ReleaseIRQ, link->handle, &link->irq); } link->state &= ~DEV_CONFIG; if (link->state & DEV_STALE_LINK) { nsp_cs_detach(link); } } /* nsp_cs_release */ /*====================================================================== The card status event handler. Mostly, this schedules other stuff to run after an event is received. A CARD_REMOVAL event also sets some flags to discourage the net drivers from trying to talk to the card any more. When a CARD_REMOVAL event is received, we immediately set a flag to block future accesses to this device. All the functions that actually access the device should check this flag to make sure the card is still present. ======================================================================*/ static int nsp_cs_event(event_t event, int priority, event_callback_args_t *args) { dev_link_t *link = args->client_data; scsi_info_t *info = link->priv; DEBUG(1, __FUNCTION__ "(0x%06x)\n", event); switch (event) { case CS_EVENT_CARD_REMOVAL: DEBUG(0, " event: remove\n"); link->state &= ~DEV_PRESENT; if (link->state & DEV_CONFIG) { ((scsi_info_t *)link->priv)->stop = 1; mod_timer(&link->release, jiffies + HZ/20); } break; case CS_EVENT_CARD_INSERTION: DEBUG(0, " event: insert\n"); link->state |= DEV_PRESENT | DEV_CONFIG_PENDING; info->bus = args->bus; nsp_cs_config(link); break; case CS_EVENT_PM_SUSPEND: link->state |= DEV_SUSPEND; /* Fall through... */ case CS_EVENT_RESET_PHYSICAL: /* Mark the device as stopped, to block IO until later */ info->stop = 1; if (link->state & DEV_CONFIG) { CardServices(ReleaseConfiguration, link->handle); } break; case CS_EVENT_PM_RESUME: link->state &= ~DEV_SUSPEND; /* Fall through... */ case CS_EVENT_CARD_RESET: DEBUG(0, " event: reset\n"); if (link->state & DEV_CONFIG) { Scsi_Cmnd tmp; CardServices(RequestConfiguration, link->handle, &link->conf); tmp.host = info->host; nsp_eh_host_reset(&tmp); } info->stop = 0; break; default: DEBUG(0, " event: unknown\n"); break; } DEBUG(0, __FUNCTION__ " end\n"); return 0; } /* nsp_cs_event */ /*======================================================================* * module entry point *====================================================================*/ static int __init nsp_cs_init(void) { servinfo_t serv; DEBUG(0, __FUNCTION__ "() in\n"); DEBUG(0, "%s\n", version); CardServices(GetCardServicesInfo, &serv); if (serv.Revision != CS_RELEASE_CODE) { printk(KERN_DEBUG "nsp_cs: Card Services release " "does not match!\n"); return -1; } register_pcmcia_driver(&dev_info, &nsp_cs_attach, &nsp_cs_detach); DEBUG(0, __FUNCTION__ "() out\n"); return 0; } static void __exit nsp_cs_cleanup(void) { DEBUG(0, __FUNCTION__ "() unloading\n"); unregister_pcmcia_driver(&dev_info); while (dev_list != NULL) { if (dev_list->state & DEV_CONFIG) { nsp_cs_release((u_long)dev_list); } nsp_cs_detach(dev_list); } } module_init(nsp_cs_init); module_exit(nsp_cs_cleanup); /* * * */ /* end */