/* USER CODE BEGIN Header */
/**
 ******************************************************************************
 * @file    hw_if.h
 * @author  MCD Application Team
 * @brief   Hardware Interface
 ******************************************************************************
 * @attention
 *
 * Copyright (c) 2019-2021 STMicroelectronics.
 * All rights reserved.
 *
 * This software is licensed under terms that can be found in the LICENSE file
 * in the root directory of this software component.
 * If no LICENSE file comes with this software, it is provided AS-IS.
 *
 ******************************************************************************
 */
/* USER CODE END Header */

/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef HW_IF_H
#define HW_IF_H

#ifdef __cplusplus
extern "C" {
#endif

/* Includes ------------------------------------------------------------------*/
#include "stm32wbxx.h"
#include "stm32wbxx_ll_bus.h"
#include "stm32wbxx_ll_cortex.h"
#include "stm32wbxx_ll_exti.h"
#include "stm32wbxx_ll_gpio.h"
#include "stm32wbxx_ll_hsem.h"
#include "stm32wbxx_ll_ipcc.h"
#include "stm32wbxx_ll_pwr.h"
#include "stm32wbxx_ll_rcc.h"
#include "stm32wbxx_ll_rtc.h"
#include "stm32wbxx_ll_system.h"
#include "stm32wbxx_ll_utils.h"

#ifdef USE_STM32WBXX_USB_DONGLE
#include "stm32wbxx_usb_dongle.h"
#endif
#ifdef USE_STM32WBXX_NUCLEO
#include "stm32wbxx_nucleo.h"
#endif
#ifdef USE_X_NUCLEO_EPD
#include "x_nucleo_epd.h"
#endif
#ifdef USE_STM32WB5M_DK
#include "stm32wb5mm_dk.h"
#endif

/* Private includes ----------------------------------------------------------*/
/* USER CODE BEGIN Includes */

/* USER CODE END Includes */

/******************************************************************************
 * HW UART
 ******************************************************************************/
typedef enum
{
    hw_uart1,
    hw_uart2,
    hw_lpuart1,
} hw_uart_id_t;

typedef enum
{
    hw_uart_ok,
    hw_uart_error,
    hw_uart_busy,
    hw_uart_to,
} hw_status_t;

void HW_UART_Init(hw_uart_id_t hw_uart_id);
void HW_UART_Receive_IT(hw_uart_id_t hw_uart_id, uint8_t * pData, uint16_t Size, void (*Callback)(void));
void HW_UART_Transmit_IT(hw_uart_id_t hw_uart_id, uint8_t * pData, uint16_t Size, void (*Callback)(void));
hw_status_t HW_UART_Transmit(hw_uart_id_t hw_uart_id, uint8_t * p_data, uint16_t size, uint32_t timeout);
hw_status_t HW_UART_Transmit_DMA(hw_uart_id_t hw_uart_id, uint8_t * p_data, uint16_t size, void (*Callback)(void));
void HW_UART_Interrupt_Handler(hw_uart_id_t hw_uart_id);
void HW_UART_DMA_Interrupt_Handler(hw_uart_id_t hw_uart_id);

/******************************************************************************
 * HW TimerServer
 ******************************************************************************/
/* Exported types ------------------------------------------------------------*/
/**
 * This setting is used when standby mode is supported.
 * hw_ts_InitMode_Limited should be used when the device restarts from Standby Mode. In that case, the Timer Server does
 * not re-initialized its context. Only the Hardware register which content has been lost is reconfigured
 * Otherwise, hw_ts_InitMode_Full should be requested (Start from Power ON) and everything is re-initialized.
 */
typedef enum
{
    hw_ts_InitMode_Full,
    hw_ts_InitMode_Limited,
} HW_TS_InitMode_t;

/**
 * When a Timer is created as a SingleShot timer, it is not automatically restarted when the timeout occurs. However,
 * the timer is kept reserved in the list and could be restarted at anytime with HW_TS_Start()
 *
 * When a Timer is created as a Repeated timer, it is automatically restarted when the timeout occurs.
 */
typedef enum
{
    hw_ts_SingleShot,
    hw_ts_Repeated
} HW_TS_Mode_t;

/**
 * hw_ts_Successful is returned when a Timer has been successfully created with HW_TS_Create(). Otherwise, hw_ts_Failed
 * is returned. When hw_ts_Failed is returned, that means there are not enough free slots in the list to create a
 * Timer. In that case, CFG_HW_TS_MAX_NBR_CONCURRENT_TIMER should be increased
 */
typedef enum
{
    hw_ts_Successful,
    hw_ts_Failed,
} HW_TS_ReturnStatus_t;

typedef void (*HW_TS_pTimerCb_t)(void);

/**
 * @brief  Initialize the timer server
 *         This API shall be called by the application before any timer is requested to the timer server. It
 *         configures the RTC module to be connected to the LSI input clock.
 *
 * @param  TimerInitMode: When the device restarts from Standby, it should request hw_ts_InitMode_Limited so that the
 *         Timer context is not re-initialized. Otherwise, hw_ts_InitMode_Full should be requested
 * @param  hrtc: RTC Handle
 * @retval None
 */
void HW_TS_Init(HW_TS_InitMode_t TimerInitMode, RTC_HandleTypeDef * hrtc);

/**
 * @brief  Interface to create a virtual timer
 *         The user shall call this API to create a timer. Once created, the timer is reserved to the module until it
 *         has been deleted. When creating a timer, the user shall specify the mode (single shot or repeated), the
 *         callback to be notified when the timer expires and a module ID to identify in the timer interrupt handler
 *         which module is concerned. In return, the user gets a timer ID to handle it.
 *
 * @param  TimerProcessID:  This is an identifier provided by the user and returned in the callback to allow
 *                          identification of the requester
 * @param  pTimerId: Timer Id returned to the user to request operation (start, stop, delete)
 * @param  TimerMode: Mode of the virtual timer (Single shot or repeated)
 * @param  pTimerCallBack: Callback when the virtual timer expires
 * @retval HW_TS_ReturnStatus_t: Return whether the creation is successful or not
 */
HW_TS_ReturnStatus_t HW_TS_Create(uint32_t TimerProcessID, uint8_t * pTimerId, HW_TS_Mode_t TimerMode,
                                  HW_TS_pTimerCb_t pTimerCallBack);

/**
 * @brief  Stop a virtual timer
 *         This API may be used to stop a running timer. A timer which is stopped is move to the pending state.
 *         A pending timer may be restarted at any time with a different timeout value but the mode cannot be changed.
 *         Nothing is done when it is called to stop a timer which has been already stopped
 *
 * @param  TimerID:  Id of the timer to stop
 * @retval None
 */
void HW_TS_Stop(uint8_t TimerID);

/**
 * @brief  Start a virtual timer
 *         This API shall be used to start a timer. The timeout value is specified and may be different each time.
 *         When the timer is in the single shot mode, it will move to the pending state when it expires. The user may
 *         restart it at any time with a different timeout value. When the timer is in the repeated mode, it always
 *         stay in the running state. When the timer expires, it will be restarted with the same timeout value.
 *         This API shall not be called on a running timer.
 *
 * @param  TimerID:  The ID Id of the timer to start
 * @param  timeout_ticks: Number of ticks of the virtual timer (Maximum value is (0xFFFFFFFF-0xFFFF = 0xFFFF0000)
 * @retval None
 */
void HW_TS_Start(uint8_t TimerID, uint32_t timeout_ticks);

/**
 * @brief  Delete a virtual timer from the list
 *         This API should be used when a timer is not needed anymore by the user. A deleted timer is removed from
 *         the timer list managed by the timer server. It cannot be restarted again. The user has to go with the
 *         creation of a new timer if required and may get a different timer id
 *
 * @param  TimerID:  The ID of the timer to remove from the list
 * @retval None
 */
void HW_TS_Delete(uint8_t TimerID);

/**
 * @brief  Schedule the timer list on the timer interrupt handler
 *         This interrupt handler shall be called by the application in the RTC interrupt handler. This handler takes
 *         care of clearing all status flag required in the RTC and EXTI peripherals
 *
 * @param  None
 * @retval None
 */
void HW_TS_RTC_Wakeup_Handler(void);

/**
 * @brief  Return the number of ticks to count before the interrupt
 *         This API returns the number of ticks left to be counted before an interrupt is generated by the
 *         Timer Server. This API may be used by the application for power management optimization. When the system
 *         enters low power mode, the mode selection is a tradeoff between the wakeup time where the CPU is running
 *         and the time while the CPU will be kept in low power mode before next wakeup. The deeper is the
 *         low power mode used, the longer is the wakeup time. The low power mode management considering wakeup time
 *         versus time in low power mode is implementation specific
 *         When the timer is disabled (No timer in the list), it returns 0xFFFF
 *
 * @param  None
 * @retval The number of ticks left to count
 */
uint16_t HW_TS_RTC_ReadLeftTicksToCount(void);

/**
 * @brief  Notify the application that a registered timer has expired
 *         This API shall be implemented by the user application.
 *         This API notifies the application that a timer expires. This API is running in the RTC Wakeup interrupt
 *         context. The application may implement an Operating System to change the context priority where the timer
 *         callback may be handled. This API provides the module ID to identify which module is concerned and to allow
 *         sending the information to the correct task
 *
 * @param  TimerProcessID: The TimerProcessId associated with the timer when it has been created
 * @param  TimerID: The TimerID of the expired timer
 * @param  pTimerCallBack: The Callback associated with the timer when it has been created
 * @retval None
 */
void HW_TS_RTC_Int_AppNot(uint32_t TimerProcessID, uint8_t TimerID, HW_TS_pTimerCb_t pTimerCallBack);

/**
 * @brief  Notify the application that the wakeupcounter has been updated
 *         This API should be implemented by the user application
 *         This API notifies the application that the counter has been updated. This is expected to be used along
 *         with the HW_TS_RTC_ReadLeftTicksToCount () API. It could be that the counter has been updated since the
 *         last call of HW_TS_RTC_ReadLeftTicksToCount () and before entering low power mode. This notification
 *         provides a way to the application to solve that race condition to reevaluate the counter value before
 *         entering low power mode
 *
 * @param  None
 * @retval None
 */
void HW_TS_RTC_CountUpdated_AppNot(void);

#ifdef __cplusplus
}
#endif

#endif /*HW_IF_H */