/* USER CODE BEGIN Header */ /** ****************************************************************************** * @file stm32wbxx_hal_conf.h * @author MCD Application Team * @brief HAL configuration file. ****************************************************************************** * @attention * * Copyright (c) 2019 STMicroelectronics. * All rights reserved. * * This software is licensed under terms that can be found in the LICENSE file * in the root directory of this software component. * If no LICENSE file comes with this software, it is provided AS-IS. * ****************************************************************************** */ /* USER CODE END Header */ /* Define to prevent recursive inclusion -------------------------------------*/ #ifndef __STM32WBxx_HAL_CONF_H #define __STM32WBxx_HAL_CONF_H #ifdef __cplusplus extern "C" { #endif /* Exported types ------------------------------------------------------------*/ /* Exported constants --------------------------------------------------------*/ /* ########################## Module Selection ############################## */ /** * @brief This is the list of modules to be used in the HAL driver */ #define HAL_MODULE_ENABLED /*#define HAL_ADC_MODULE_ENABLED */ /*#define HAL_CRYP_MODULE_ENABLED */ /*#define HAL_COMP_MODULE_ENABLED */ /*#define HAL_CRC_MODULE_ENABLED */ #define HAL_HSEM_MODULE_ENABLED #define HAL_I2C_MODULE_ENABLED #define HAL_IPCC_MODULE_ENABLED /*#define HAL_IRDA_MODULE_ENABLED */ /*#define HAL_IWDG_MODULE_ENABLED */ /*#define HAL_LCD_MODULE_ENABLED */ /*#define HAL_LPTIM_MODULE_ENABLED */ /*#define HAL_PCD_MODULE_ENABLED */ /*#define HAL_PKA_MODULE_ENABLED */ #define HAL_QSPI_MODULE_ENABLED #define HAL_RNG_MODULE_ENABLED #define HAL_RTC_MODULE_ENABLED /*#define HAL_SAI_MODULE_ENABLED */ /*#define HAL_SMBUS_MODULE_ENABLED */ /*#define HAL_SMARTCARD_MODULE_ENABLED */ #define HAL_SPI_MODULE_ENABLED #define HAL_TIM_MODULE_ENABLED /*#define HAL_TSC_MODULE_ENABLED */ #define HAL_UART_MODULE_ENABLED /*#define HAL_USART_MODULE_ENABLED */ /*#define HAL_WWDG_MODULE_ENABLED */ #define HAL_EXTI_MODULE_ENABLED #define HAL_CORTEX_MODULE_ENABLED #define HAL_DMA_MODULE_ENABLED #define HAL_FLASH_MODULE_ENABLED #define HAL_GPIO_MODULE_ENABLED #define HAL_PWR_MODULE_ENABLED #define HAL_RCC_MODULE_ENABLED #define USE_HAL_ADC_REGISTER_CALLBACKS 0u #define USE_HAL_COMP_REGISTER_CALLBACKS 0u #define USE_HAL_CRYP_REGISTER_CALLBACKS 0u #define USE_HAL_I2C_REGISTER_CALLBACKS 0u #define USE_HAL_IRDA_REGISTER_CALLBACKS 0u #define USE_HAL_LPTIM_REGISTER_CALLBACKS 0u #define USE_HAL_PCD_REGISTER_CALLBACKS 0u #define USE_HAL_PKA_REGISTER_CALLBACKS 0u #define USE_HAL_QSPI_REGISTER_CALLBACKS 0u #define USE_HAL_RNG_REGISTER_CALLBACKS 0u #define USE_HAL_RTC_REGISTER_CALLBACKS 0u #define USE_HAL_SAI_REGISTER_CALLBACKS 0u #define USE_HAL_SMARTCARD_REGISTER_CALLBACKS 0u #define USE_HAL_SMBUS_REGISTER_CALLBACKS 0u #define USE_HAL_SPI_REGISTER_CALLBACKS 0u #define USE_HAL_TIM_REGISTER_CALLBACKS 0u #define USE_HAL_TSC_REGISTER_CALLBACKS 0u #define USE_HAL_UART_REGISTER_CALLBACKS 0u #define USE_HAL_USART_REGISTER_CALLBACKS 0u #define USE_HAL_WWDG_REGISTER_CALLBACKS 0u /* ########################## Oscillator Values adaptation ####################*/ /** * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. * This value is used by the RCC HAL module to compute the system frequency * (when HSE is used as system clock source, directly or through the PLL). */ #if !defined(HSE_VALUE) #define HSE_VALUE 32000000U /*!< Value of the External oscillator in Hz */ #endif /* HSE_VALUE */ #if !defined(HSE_STARTUP_TIMEOUT) #define HSE_STARTUP_TIMEOUT ((uint32_t) 100) /*!< Time out for HSE start up, in ms */ #endif /* HSE_STARTUP_TIMEOUT */ /** * @brief Internal Multiple Speed oscillator (MSI) default value. * This value is the default MSI range value after Reset. */ #if !defined(MSI_VALUE) #define MSI_VALUE ((uint32_t) 4000000) /*!< Value of the Internal oscillator in Hz*/ #endif /* MSI_VALUE */ /** * @brief Internal High Speed oscillator (HSI) value. * This value is used by the RCC HAL module to compute the system frequency * (when HSI is used as system clock source, directly or through the PLL). */ #if !defined(HSI_VALUE) #define HSI_VALUE 16000000U /*!< Value of the Internal oscillator in Hz*/ #endif /* HSI_VALUE */ /** * @brief Internal Low Speed oscillator (LSI1) value. */ #if !defined(LSI1_VALUE) #define LSI1_VALUE ((uint32_t) 32000) /*!< LSI1 Typical Value in Hz*/ #endif /* LSI1_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz \ The real value may vary depending on the variations \ in voltage and temperature.*/ /** * @brief Internal Low Speed oscillator (LSI2) value. */ #if !defined(LSI2_VALUE) #define LSI2_VALUE ((uint32_t) 32000) /*!< LSI2 Typical Value in Hz*/ #endif /* LSI2_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz \ The real value may vary depending on the variations \ in voltage and temperature.*/ /** * @brief External Low Speed oscillator (LSE) value. * This value is used by the UART, RTC HAL module to compute the system frequency */ #if !defined(LSE_VALUE) #define LSE_VALUE 32768U /*!< Value of the External oscillator in Hz*/ #endif /* LSE_VALUE */ /** * @brief Internal Multiple Speed oscillator (HSI48) default value. * This value is the default HSI48 range value after Reset. */ #if !defined(HSI48_VALUE) #define HSI48_VALUE ((uint32_t) 48000000) /*!< Value of the Internal oscillator in Hz*/ #endif /* HSI48_VALUE */ #if !defined(LSE_STARTUP_TIMEOUT) #define LSE_STARTUP_TIMEOUT 5000U /*!< Time out for LSE start up, in ms */ #endif /* LSE_STARTUP_TIMEOUT */ /** * @brief External clock source for SAI1 peripheral * This value is used by the RCC HAL module to compute the SAI1 & SAI2 clock source * frequency. */ #if !defined(EXTERNAL_SAI1_CLOCK_VALUE) #define EXTERNAL_SAI1_CLOCK_VALUE ((uint32_t) 2097000) /*!< Value of the SAI1 External clock source in Hz*/ #endif /* EXTERNAL_SAI1_CLOCK_VALUE */ /* Tip: To avoid modifying this file each time you need to use different HSE, === you can define the HSE value in your toolchain compiler preprocessor. */ /* ########################### System Configuration ######################### */ /** * @brief This is the HAL system configuration section */ #define VDD_VALUE 3300U /*!< Value of VDD in mv */ #define TICK_INT_PRIORITY 0U /*!< tick interrupt priority */ #define USE_RTOS 0U #define PREFETCH_ENABLE 1U #define INSTRUCTION_CACHE_ENABLE 1U #define DATA_CACHE_ENABLE 1U /* ########################## Assert Selection ############################## */ /** * @brief Uncomment the line below to expanse the "assert_param" macro in the * HAL drivers code */ /* #define USE_FULL_ASSERT 1U */ /* ################## SPI peripheral configuration ########################## */ /* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver * Activated: CRC code is present inside driver * Deactivated: CRC code cleaned from driver */ #define USE_SPI_CRC 0U /* Includes ------------------------------------------------------------------*/ /** * @brief Include module's header file */ #ifdef HAL_DMA_MODULE_ENABLED #include "stm32wbxx_hal_dma.h" #endif /* HAL_DMA_MODULE_ENABLED */ #ifdef HAL_ADC_MODULE_ENABLED #include "stm32wbxx_hal_adc.h" #endif /* HAL_ADC_MODULE_ENABLED */ #ifdef HAL_COMP_MODULE_ENABLED #include "stm32wbxx_hal_comp.h" #endif /* HAL_COMP_MODULE_ENABLED */ #ifdef HAL_CORTEX_MODULE_ENABLED #include "stm32wbxx_hal_cortex.h" #endif /* HAL_CORTEX_MODULE_ENABLED */ #ifdef HAL_CRC_MODULE_ENABLED #include "stm32wbxx_hal_crc.h" #endif /* HAL_CRC_MODULE_ENABLED */ #ifdef HAL_CRYP_MODULE_ENABLED #include "stm32wbxx_hal_cryp.h" #endif /* HAL_CRYP_MODULE_ENABLED */ #ifdef HAL_EXTI_MODULE_ENABLED #include "stm32wbxx_hal_exti.h" #endif /* HAL_EXTI_MODULE_ENABLED */ #ifdef HAL_FLASH_MODULE_ENABLED #include "stm32wbxx_hal_flash.h" #endif /* HAL_FLASH_MODULE_ENABLED */ #ifdef HAL_GPIO_MODULE_ENABLED #include "stm32wbxx_hal_gpio.h" #endif /* HAL_GPIO_MODULE_ENABLED */ #ifdef HAL_HSEM_MODULE_ENABLED #include "stm32wbxx_hal_hsem.h" #endif /* HAL_HSEM_MODULE_ENABLED */ #ifdef HAL_I2C_MODULE_ENABLED #include "stm32wbxx_hal_i2c.h" #endif /* HAL_I2C_MODULE_ENABLED */ #ifdef HAL_IPCC_MODULE_ENABLED #include "stm32wbxx_hal_ipcc.h" #endif /* HAL_IPCC_MODULE_ENABLED */ #ifdef HAL_IRDA_MODULE_ENABLED #include "stm32wbxx_hal_irda.h" #endif /* HAL_IRDA_MODULE_ENABLED */ #ifdef HAL_IWDG_MODULE_ENABLED #include "stm32wbxx_hal_iwdg.h" #endif /* HAL_IWDG_MODULE_ENABLED */ #ifdef HAL_LCD_MODULE_ENABLED #include "stm32wbxx_hal_lcd.h" #endif /* HAL_LCD_MODULE_ENABLED */ #ifdef HAL_LPTIM_MODULE_ENABLED #include "stm32wbxx_hal_lptim.h" #endif /* HAL_LPTIM_MODULE_ENABLED */ #ifdef HAL_PCD_MODULE_ENABLED #include "stm32wbxx_hal_pcd.h" #endif /* HAL_PCD_MODULE_ENABLED */ #ifdef HAL_PKA_MODULE_ENABLED #include "stm32wbxx_hal_pka.h" #endif /* HAL_PKA_MODULE_ENABLED */ #ifdef HAL_PWR_MODULE_ENABLED #include "stm32wbxx_hal_pwr.h" #endif /* HAL_PWR_MODULE_ENABLED */ #ifdef HAL_QSPI_MODULE_ENABLED #include "stm32wbxx_hal_qspi.h" #endif /* HAL_QSPI_MODULE_ENABLED */ #ifdef HAL_RCC_MODULE_ENABLED #include "stm32wbxx_hal_rcc.h" #endif /* HAL_RCC_MODULE_ENABLED */ #ifdef HAL_RNG_MODULE_ENABLED #include "stm32wbxx_hal_rng.h" #endif /* HAL_RNG_MODULE_ENABLED */ #ifdef HAL_RTC_MODULE_ENABLED #include "stm32wbxx_hal_rtc.h" #endif /* HAL_RTC_MODULE_ENABLED */ #ifdef HAL_SAI_MODULE_ENABLED #include "stm32wbxx_hal_sai.h" #endif /* HAL_SAI_MODULE_ENABLED */ #ifdef HAL_SMARTCARD_MODULE_ENABLED #include "stm32wbxx_hal_smartcard.h" #endif /* HAL_SMARTCARD_MODULE_ENABLED */ #ifdef HAL_SMBUS_MODULE_ENABLED #include "stm32wbxx_hal_smbus.h" #endif /* HAL_SMBUS_MODULE_ENABLED */ #ifdef HAL_SPI_MODULE_ENABLED #include "stm32wbxx_hal_spi.h" #endif /* HAL_SPI_MODULE_ENABLED */ #ifdef HAL_TIM_MODULE_ENABLED #include "stm32wbxx_hal_tim.h" #endif /* HAL_TIM_MODULE_ENABLED */ #ifdef HAL_TSC_MODULE_ENABLED #include "stm32wbxx_hal_tsc.h" #endif /* HAL_TSC_MODULE_ENABLED */ #ifdef HAL_UART_MODULE_ENABLED #include "stm32wbxx_hal_uart.h" #endif /* HAL_UART_MODULE_ENABLED */ #ifdef HAL_USART_MODULE_ENABLED #include "stm32wbxx_hal_usart.h" #endif /* HAL_USART_MODULE_ENABLED */ #ifdef HAL_WWDG_MODULE_ENABLED #include "stm32wbxx_hal_wwdg.h" #endif /* HAL_WWDG_MODULE_ENABLED */ /* Exported macro ------------------------------------------------------------*/ #ifdef USE_FULL_ASSERT /** * @brief The assert_param macro is used for function's parameters check. * @param expr If expr is false, it calls assert_failed function * which reports the name of the source file and the source * line number of the call that failed. * If expr is true, it returns no value. * @retval None */ #define assert_param(expr) ((expr) ? (void) 0U : assert_failed((uint8_t *) __FILE__, __LINE__)) /* Exported functions ------------------------------------------------------- */ void assert_failed(uint8_t * file, uint32_t line); #else #define assert_param(expr) ((void) 0U) #endif /* USE_FULL_ASSERT */ #ifdef __cplusplus } #endif #endif /* __STM32WBxx_HAL_CONF_H */