ampwait.1

[PREV] [HOME] [NEXT]

ampwait(1) Qualcomm Atheros Open Powerline Toolkit ampwait(1)

NAME
ampwait - Qualcomm Atheros Powerline Procrastinator

SYNOPSIS
ampwait [options] [device] [device] [...]

DESCRIPTION
Poll a Qualcomm Atheros powerline device, waiting for one or more events to occur before continuing or returning. The
events include reset or power off, restart or power on and network association. It is used to pause shell scripts at
critical points where a device must be in a known state before continuing.

This program is part of the Qualcomm Atheros Powerline Toolkit. See the plc man page for an overview and installation
instructions.

OPTIONS
-a Poll the device every few seconds using VS_NW_INFO messages until the device indicates that a networks exists and
has at least one station. This option can give false readings if other devices have dropped off-line and the
device bridging table still holds information about them. The program always checks for this event last if other
event options are specified.

-e Redirects stderr messages to stdout. By convention status and error messages are printed on stderr while primary
program output is printed on stdout. This option prints all output on stdout in cases where this is desired.

-f firmware
The identification string for firmware that should be running after the device starts. This option can be used to
detect a failed firmware load. If the actual identification string does not match this one once the device starts
then an error is reported. If option -x is present then the program terminates with a non-zero exit code. This
option has no effect unless option -s is present. An identification string looks like
"INT6000-MAC-3-1-3143-1690-20071107-FINAL-B" and can be obtained using int6k -r.

-i Select the host Ethernet interface. All requests are sent via this host interface and only reponses received via
this host interface are recognized. The default interface is eth1 because most people use eth0 as their principle
network connection; however, if environment string "PLC" is defined then it takes precedence over the default
interface. This option then takes precedence over either default.

-p seconds
Fixed pause time in seconds. This adds an fixed delay after the other events have occured. A pause does not
occur if any of the specified events timeout. When no other events are specified this option is effectively
equivalent to sleep. This option can be used to allow the device or the network to settle. For example, a nomi‐
nal 5 second wait is recommended after a device successfully associates before attempting to transfer data.

-q Enter quiet mode. Progress messages are suppressed.

-R Reset the device then check return status. Exit program on error if option -x is present; otherwise, repeat the
reset request until the device either accepts the request or the wait time is exceeded.

-s Poll the device every few seconds using VS_SW_VER messages until the bootloader or runtime firmware responds or
the poll count exhausts. The presence of a response indicates that the device has either connected to the host,
received power or finished reboot.

-t milliseconds
Channel read/write timeout in milliseconds. This is the maximum time allowed for a confirmation or a response
from a powerline device before abandoning a read/write operation. Permitted values range from 0 through UINT_MAX
as defined in limits.h. The default is 50 milliseconds.

-v Enter verbose mode. All Etherenet frames sent or received by the program are displayed on stdout.

-w seconds
Wait timeout in seconds. This is the maximum time that this application will wait for an event to occur where an
event is reset, start or assoc. If an event does no occur within this time, the program proceeds to wait for the
next specified event. This timeout applies to each event in turn when more than one event is specified. Permit‐
ted values are 0 through 86400 seconds which is 24 hours.

-x Exit program on first error with a non-zero exit code. This option allows shell scripts to detect failed or
incomplete operations and take the appropriate action.

-y Display actual wait times on stdout.

-?, --help
Print program help summary on stdout. This option takes precedence over other options on the command line.

-!, --version
Print program version information on stdout. This option takes precedence over other options on the command line.
Use this option when sending screen dumps to Atheros Technical Support so that they know exactly which version of
the Linux Toolkit you are using.

ARGUMENTS
device The Media Access Control (MAC) address of some device. Addresses are 6 hexadecimal octets optionally separated by
colon. For example, the addresses "00b052000001", "00:b0:52:00:00:01" and "00b052:000001" are all valid and
equivalent. For convenience, the symbolic address "local" resolves to "00:b0:52:00:00:01" and the symbolic
addresses "all" and "broadcast" both resolve to "ff:ff:ff:ff:ff:ff".

REFERENCES
See the Qualcomm Atheros HomePlug AV Firmware Technical Reference Manual for more information.

DISCLAIMER
Atheros HomePlug AV Vendor Specific Management Message Entry structure and content is proprietary to Qualcomm Atheros,
Ocala FL USA. Consequently, public information may not be available. Qualcomm Atheros reserves the right to modify mes‐
sage structure and content in future firmware releases without any obligation to notify or compensate users of this pro‐
gram.

EXAMPLES
The following command polls the local device until firmware stops running then polls the device until firmware starts
running again. This command can be inserted into a shell script at a point where the device must reset and reboot before
proceeding. Observe that the program waits up to 60 seconds for each event, in turn, because 60 seconds is the default
wait period. If an event occurs before the specified timeout the program will move on to the next event.

# ampwait -rs
eth0 00:B0:52:BA:BA:01 Allow 60 seconds for Reset
eth0 00:B0:52:BA:BA:01 Allow 60 seconds for Start

The following example waits up to 30 seconds for the local device to reset (-r) then up to 50 seconds for the local
device to start (-s). This is the same as above but we have specified 30 seconds using option -w.

# ampwait -r -s -w 30
eth0 00:B0:52:BA:BA:01 Allow 30 seconds for Reset
eth0 00:B0:52:BA:BA:01 Allow 30 seconds for Start

The next example reports the actual amount of time taken for each event to occur. Observe that the last event, device
association, did not occur within the allotted time.

# ampwait -rsay
eth0 00:B0:52:BA:BA:01 Allow 60 seconds for Reset
etho 00:B0:52:BA:BA:01 Waited 22 seconds to Reset
eth0 00:B0:52:BA:BA:01 Allow 60 seconds for Start
etho 00:B0:52:BA:BA:01 Waited 4 seconds to Start
eth0 00:B0:52:BA:BA:01 Allow 60 seconds for Assoc
etho 00:B0:52:BA:BA:01 Waited 60 seconds for Assoc
etho 00:B0:52:BA:BA:01 Device did not Assoc

The following example illustrates use of the revision string to detect mismatched firmware. In this example, we reset
the device first, using program amptool, then wait for it to reset then start up again. There are also operation that
can cause the device to reset.

# amptool -R
# ampwait -xrsf INT6000-MAC-3-1-3143-1690-20071107-FINAL-B
eth0 00:B0:52:BA:BA:01 Device started wrong firmware

Immediately after a reset we wait for the firmware to stop responding, with option -r, and then start responding, with
option -s, and then perform a string comparison against the actual firmware revision string, with option -f. If the
strings do not match then an error is reported. In this case, the program will exit with a non-zero return code since
option -x is present.

SEE ALSO
amp(1), amptool(1), amphost(1), amprate(1), ampid(1), ampstat(1)

CREDITS
Charles Maier <cmaier@qca.qualcomm.com>

open-plc-utils-0.0.3 Mar 2014 ampwait(1)

[PREV] [HOME] [NEXT]